Planar PT1501MX, PT1500MX, PT1585P, PT1550MX, PT1575S User Manual 2

PT1500MX / PT1550MX / PT1501MX / PT1575S / PT1585P Touch Screen LCD Monitors

USER’S GUIDE

www.planartouch.com

Important Recycle Instructions:

Lamp(s) inside this product contains mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordanc e with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG

For more information on how to recycle your product, please visit

WWW.PLANARSYSTEMS.COM/GREEN.

. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG.

Table of Contents

Usage Notice ........................................................................... 3

Precautions .........................................................................................3

Introduction ............................................................................. 4

About PT1500MX / PT1550MX / PT1501MX / PT1575S / PT1585P ..4

Touch Screen for PT1500MX / PT1550MX.................................. 4

Touch Screen for PT1501MX.......................................................4

Touch Screen for PT1575S..........................................................4

Touch Screen for PT1585P..........................................................6

Package Overview ..............................................................................7

Installation ............................................................................... 8

Product Overview................................................................................8

Front View......................................................................................8

PT1500MX / PT1550MX / PT1501MX / PT1575S Bottom View....8

PT1585P Bottom View................................................................... 8

Start Your Installation ..........................................................................9

Connecting the Display (Figure 12.1)................................................ 11

Kensington Security Slot ...................................................................13

VESA Mount your monitor................................................................. 14

Remove the Deskstand..............................................................15

User Controls ........................................................................ 16

Side Panel Controls ..........................................................................16

How to Use the OSD Menus .............................................................17

On-Screen

Display

Menus

.............................................................19

Appendix................................................................................ 20

Troubleshooting.................................................................................20

Warning Signal..................................................................................21

No Signal ....................................................................................21

Going to Sleep .............................................................................21

Out of Range ...............................................................................21

Product Dimensions ..........................................................................22

Compatibility Modes..........................................................................24

Touch Screen Driver Installation .......................................................25

Product Registration and Technical Support..................................... 31

Usage Notice

Warning- To prevent the risk of fire or shock hazards, do not

expose this product to rain or moisture.

Warning- Please do not open or disassemble the product as

this may cause electric shock.

Precautions

Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit.

Do:

 Turn off the product before cleaning.  Touch screen surface may be cleaned using a soft clean cloth

moistened with mild window glass commercial cleaners or 50/5 0 mixture of water and isopropyl alcohol.

 Use a soft cloth moistened with mild detergent to clean the display

housing.

 Use only high quality and safety approved AC/DC adapter.  Disconnect the power plug from AC outlet if the product is not going

to be used for an extended period of time.

Don’t:

 Do not touch the LCD Display screen surface with sharp or hard

objects.

 Do not use abrasive cleaners, waxes or solvents for your cleanin g.  Do not operate the product under the following conditions:

- Extremely hot, cold or humid environment.

- Areas susceptible to excessive dust and dirt.

- Near any appliance generating a strong magnetic field.

- In direct sunlight.

Introduction

About PT1500MX / PT1550MX / PT1501MX / PT1575S / PT1585P

The PT1500MX / PT1550MX / PT1501MX / PT1575S / PT1585P is a 15” flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD).

Features include:

 Direct Analog signal input  Active matrix TFT LCD technology  1024x768 XGA resolution  15” viewable display area  31.47 ~ 60.02 kHz horizontal scan  56 ~ 75 Hz high refresh rate  0.297mm x 0.297mm pixel pitch  Auto adjustment function  Multilingual OSD user controls  VESA DPMS power saving  Kensington security slot  75 mm VESA mount  Removable base for flexible mounting solutions.  PT1500MX / PT1550MX – 5-wire resistive touch screen with dual RS-232

Serial/USB controller

 PT1501MX – Capacitive touch screen with dual RS-232 Serial/USB

controller

 PT1575S – SAW touch screen with dual RS-232 Serial/USB controller  PT1585P – Projected capacitive touch screen with USB controller  Built-in speakers-1W X 2

Touch Screen for PT1500MX / PT1550MX

 5-wire resistive touch screen for finger and stylus input  Surface: Anti-glare treatment  Interface: Dual RS-232 Serial/USB controller  Durability: 35 million touches at a single point  Hardness of surface: 3H Typical  Operating force: 40g~200g when using a silicon rubber tipped pen with a

1 mm diameter minimum and a hardness of 60 degree.

 Transmittance: 82%±5%  Driver: Windows

Linux, Apple

7, VISTA, XP, 2000, ME, 98, NT4.0, CE, XP Embedded,

Mac OS

Touch Screen for PT1501MX

 Capacitive touch screen for finger input  Surface: Anti-glare treatment  Interface: Dual RS-232 Serial/USB controller  Durability: 225 million touches at a single point  Hardness of surface: Mohs’ Hardness rating of 7  Transmittance: 85%±5%  Driver: Windows

Linux, Apple

7, VISTA, XP, 2000, ME, 98, NT4.0, CE, XP Embedded,

Mac OS

Touch Screen for PT1575S

 Surface Acoustic Wave (SAW) touch screen for finger and stylus input  Surface: Anti-glare treatment  Interface: Dual RS-232 Serial/USB controller  Durability: 50 million touches at a single point  Hardness of surface: Mohs’ Hardness rating of 7  Operating force: Typically less than 85 g  Transmittance: 92%±5%  Driver: Windows

Linux, Apple

7, VISTA, XP, 2000, ME, 98, NT4.0, CE, XP Embedded,

Mac OS

Touch Screen for PT1585P

 Project capacitive touch screen for finger input only  Surface: Glare treatment  Interface: USB controller  Transmittance: 90%±5%  Driver: Windows

Express, Linux, Apple

7, VISTA 64/32 bits, XP, 2000, CE, XP Embedded

Mac OS

Package Overview

LCD Display Power Cord VGA Signal Cable

USB Cable (A to A)

(PT1550MX)

USB Cable (A to B) Touch Screen Driver

Audio-in Cable

Installation CD-ROM

RS-232 Cable

(PT1500MX / PT1550MX

PT1501MX / PT1575S only)

User’s Manual

User’s Guide

Landing Strip DC Power Supply

(sold separately)

Screw

Cable Cover

Installation

Product Overview

► Front View

PT1500MX/PT1550MX PT1585P PT1501MX/PT1575S

► PT1500MX/PT1550MX/PT1501MX/PT1575S

Bottom View (Without Stand)

► PT1585P Bottom View (Without Stand)

Start Your Installation

1. Lay the LCD flat on an even surfa ce.

2. Remove the stand back cover by pullin g in the directi on of the arrow a s seen in step 2 diagram.

3. Move the stand into position as seen in step 3 diagra m.

4. Connect the cables to the appropriate connectors as seen in Step 4 diagram. Use step 4-1 diagram if using the RS-232 seri al connecto r. Use step 4-2 diagram if using the USB connector.

+ 23 hidden pages