The information contained in this document is subject to change without notice.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be reproduced, translated to
another language or stored in a retrieval system, or transmitted by any means,
electronic, mechanical, photocopying, recording, or otherwise, without prior written
permission.
Windows is a registered trademark of Microsoft, Inc.
Other brand or product names are trademarks of their respective holders.
Contents
Important Information........................................................................................................................... 1
"CAUTION: If the same image is displayed continuously, a permanent image
may remain on the screen. This is due to burning of the fluorescent material and
is typical for all Plasma displays. To minimize this, use at least the display
picture move feature, selectable through the on-screen display adjustment
menu (OSD)."
Warning: To reduce the risk of fire or electric shock, do not expose this product to
rain or moisture.
Caution: To reduce the risk of electric shock, do not remove cover (or back). No
user-serviceable parts inside. Refer servicing to qualified service personnel.
Note to CATV system installer: This reminder is provided to call CATV system installer’s
attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian
Electrical Code, Part 1), that provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the
building as close as to the point of cable entry as practical.
Example of antenna grounding as per National Electrical Code is as the following picture.
Caution: FCC/ CSA regulations state that any unauthorized changes or
modifications to this equipment may void the user's authority to operate it.
Important: One Federal Court has held that unauthorized recording of copyrighted TV
programs is an infringement of U.S. copyright laws. Certain Canadian programs
may also be copyrighted and any unauthorized recording in whole or in part may be in
violation of these rights.
CAUTION
Risk of electric
shock. Do not open.
1
Safety Precautions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long period of
time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have galled into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15. Apparatus shall not be exposed to dripping or splashing and no objects filled
with liquids, such as vases, shall be placed on the apparatus.
2
Product Features
The Product features include:
Built-in Screen Move: Screen move feature to reduce the possibility of screen
burn.
3-D Digital Comb Filter: Enhances color purity of Composite Video and TV
input sources, reducing cross-color artifacts like dot crawl and moiré.
Wide Viewing Angle: Over 160 degrees (horizontal and vertical) viewing angle.
Picture in Picture: Users may simultaneously watch two images from different
video sources.
Channel Memory: Allows users to add and remove channel according to
personal preference.
16:9 Enhancement: Widescreen technology that maximizes picture quality
when playing widescreen enhanced video.
Parental Control: V-Chip technology allows parents to block unsuitable
programming for under age viewers.
Color Temperature: 3 user selectable color temperature settings are available
for image optimization.
D-Sub 15 VGA Input: Allows users to connect the computer to the plasma TV
to use the plasma TV as a computer monitor.
Digital Visual Interface (DVI): This product is equipped with a DVI-D interface
for a digital-to-digital connection.
TV Tuner Built-in: Built-in NTSC tuner to receive conventional analog
broadcasts; de-interlacing circuit with 3:2 pull down converting interlaced
analog sources to the progressive-scan display, significantly improving picture
quality
Built-in TV Video and Audio Out: Outputs TV video/audio signal to an external
device.
Built-in Speakers: Built-in stereo speakers with 3 watts per channel.
Input Signals
Component Video (YCbCr/ YPbPr)
Composite Video
S-Video
Analog VGA (D-Sub 15pin)
Digital DVI
RS232 Communication Port (D-Sub 9pin)
TV Tuner Built-in
(1) an optional set-top HDTV receiver box is required to receive digital signals
3
Content of Package
When you are unpacking the product, make sure that you have the following items:
Plasma TV Monitor Monitor Stand
Power cord S-Video cable
Analog video signal cable
(D-Sub 15 cable)
RCA Video/Audio cable
Remote Control and AAA Battery User’s Manual
4
If you find that any of these items are missing or appear damaged, please contact
your dealer immediately. Do not throw away the packing material or shipping
carton in case you need to ship or store the plasma TV in the future.
Optional Accessories
External Speakers and Stands
Wall mount bracket
5
Quick Start
Front Panel
Indicator Light
Remote Control Sensor
Remote Control Sensor: Receives infrared signals from the remote control.
Aim the remote control within 30 degrees left and right.
Indicator Light: This LED light indicates the main power status.
Indicator (Amber): Standby mode
Indicator (Blue): Power ON mode
6
Front Panel Controls
Menu Volume Up/Down
Select
Button Function
Menu Displays the OSD menu
Volume Up (X)
Down (W)
Select
Channel Up (S)
Down (T)
(1) Adjust volume by pressing "W" to decrease the volume and "X" to
increase the volume
(2) Change the configurations under the OSD menu
Switches between signal sources. The signal source selection is in a
loop:
Composite-Video --> S-Video --> Component-Video --> TV --> ANALOG
VGA --> DVI
(1) Changing channel under TV mode
(2) Select options under OSD menu
Channel Up/Down
Standby/On
Standby/On Power on the plasma TV or change to Standby mode
7
Rear Panel
Video/Audio
Line Out
Video/Audio Connection Interface: Video connection includes Component
Video, Composite Video, S-video, DVI, D-Sub 15, TV Tuner, and TV Video/Audio
Out.
Main Power Switch: Master power switch to switch the plasma TV between
Power Off mode and Standby mode.
Power Input Jack: Power source for the plasma TV.
External Speaker Line Out: Allows users to connect external speakers to the
plasma TV.
Connection Interface
Main Power Switch
Power Input Jack External Speaker
8
Set-up Instructions
Getting Started
Power Input Jack: Auto switch power supply accepts input of 100 VAC~240
VAC. Use only UL approved power cord with proper grounding.
Main Power Switch: Press the Power Switch on the back of your plasma TV. The
Indicator Light on the front will turn to Amber color indicating the plasma TV is
in Standby mode. If the plasma TV will not be used for an extended period of
time, turn off your plasma TV with the Main Power Switch.
9
Video/Audio Connection
Composite (AV) Input: Single RCA connector to connect with the composite
video output of a DVD Player, VCR or any other device with a composite video
connection.
S-Video Input: Single S-video connector to connect with the S-video output of
a DVD Player, VCR or any other device with a S-video connection.
Component Video Input: 3 RCA connectors to connect with the component
video output of a DVD player, DTV receiver or any other device with a
component connection.
Composite (AV)/S-Video Audio: 2 RCA connectors to connect with the audio
output of the composite or s-video source.
Component Audio: 2 RCA connectors to connect with the audio output of the
component Y/Cb/Cr or Y/Pb/Pr source.
PC Audio: 2 RCA connectors to connect with the audio output of a PC.
TV Video/Audio Out: 3 RCA connectors (1 video and 2 audio) that output the
TV video and audio signals to an external device.
10
External Speakers
+
ExternalSpeaker Line Out:
External speaker output. Please
refer to the drawing for the
connection details. It is strongly
recommend to use only Planar
Accessories for performance and
safety purposes.
11
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.