Dome Surgery Review Cart
The portability of the Dome Surgery Review Cart allows you to implement a DICOM-compliant, PACS referral
viewing station—on demand—in any area of a healthcare facility. When it is fully integrated, the cart consists of
the computer unit that you supply and these components:
• Review cart for attaching computer and display • Dome CXtra software for DICOM compliance
• One or two displays for side-by-side image review • Cleanable keyboard and mouse
• Display controller and driver • Power adapters (display dependent)
The displays available in dual-unit cart configurations include the Dome C3i, Dome E2, Dome E2c, Dome E3,
Dome E3c, Dome P2, and Dome Q2 displays. The Dome E4c display, designed for widescreen diagnostic imaging,
is also available in a single-unit cart configuration.
To facilitate integration at your location, Planar has partially assembled the review cart by prerouting power and
video cables. You need only to install the display controller into your computer, attach the computer and the
Dome displays to the cart, and connect the power and video cables. Check the display documentation for safety
guidelines on handling the components.
System Requirements
Check that the computer unit you are mounting to the
cart has the following bus interface per configuration:
Dome RP2 or Dome RQ2 using the AX1 or EX2 board
Dome RE2c using the AX1 board
•AX1 board
•EX2 board
AGP slot: H 4.2"
– PCIe bus with full-height 16x slot
– AGP 8X/4X bus with full-height
Dome RE3, Dome RE3c, or Dome RE4c using
the AX3 board
PCIe bus with full-height 16x slot
Dome RC3, Dome RE2, Dome RE3, or
Dome RE3c using the DX2 board
Full height half length PCI slot: H 4.2" x L 6.95"
(PCI64/66 slot recommended)
Your computer unit must also meet the following
requirements:
• Size (W x H x D) – No larger than 7.5" x 18" x 20"
(190 mm x 406 mm x 508 mm)
• Weight – No heavier than 35 lb (16 kg)
• Intel Pentium 4/Xeon clocked at 2.0 GHz (or faster),
AMD Athlon/Opteron with 2000+ rating (or faster),
or equivalent CPU
•CD-ROM drive
• Microsoft Windows XP or Windows 2000 with
Service Pack 4 or higher
• 256 MB or more system memory
• 350 Watt (or greater) power supply
The Dome E4c display mounted to the cart. Other display
configurations may have variations for power supply
connection and peripherals.
ONE: Checking the Package Contents
The components for the review cart ship in two boxes. Confirm that you have received these items.
Box 1: Preconfigured cart, containing:
– Video and power cables (2 each),
routed
– Power supplies (2), mounted,
as required per display
– Keyboard and mouse
– Keyboard cover
– Mounting brackets with VESA
100-mm hole pattern, attached
– Power strip (4 outlets), mounted
and routed
– Computer straps (2)
–Cable ties (5)
Box 2: Dual Dome CX, EX, PX, or QX or single Dome E4c display unit, including:
– Screws, Phillips buttonhead (8)
–Display controller
– Driver software
– Display documentation
–Dome CXtra software
TWO: Installing the Display Controller
Install the display controller into your computer before you attach the computer to the cart. Refer to the display
documentation for instructions.
THREE: Mounting the Computer
Be sure to center the computer unit on the L-bracket for stability. To use a UPS on the cart, position the device on the shelf at
the bottom of the cart, as shown in step 3. Use a 3" x 5" pad of hook & loop tape on the bottom of the UPS. Secure the UPS
to the shelf with long cable ties routed around the UPS and through the four slits on the bracket.
1
Position the cart so that you face
the rear. Lock the front wheels.
2
Remove the cables bundled on
the L-bracket and unfasten the straps.
3
Place the computer on the
L-bracket and secure the straps.
FOUR: Mounting Dual Displays
Mounting dual displays to the cart is a two-person task. Ask someone to hold each display in place, while you secure it to
the mounting bracket. See page 3 for mounting of the Dome E4c display.
1
Attach the first display to
a mounting bracket and secure
the two top screws.
2
Rotate the display to landscape
mode to secure the two bottom
screws. Repeat steps 1 and 2 for
the second display.
3
Slide the mounting brackets
toward the center so that the dual
displays are side by side.
Mounting the Dome E4c Display
Ask someone to help you lift and mount the display. You also need a protective cloth on which to put the display
screen-down (on a flat surface) to adjust and remove the mounting screws.
1
Loosen the four top mounting
screws until they protrude halfway
from the display. The screws must still
be firmly seated. Completely remove
the four bottom screws.
2
With a person on each side, lift the
display and set the protruding screws
into the top screw slots to hook the
display onto the mounting bracket.
3
Insert the four bottom screws into
the mounting bracket and the display.
Tighten all the screws. Use the lever on
the bracket to adjust the tilt position
of the display.
FIVE: Connecting the Power Cords and Video Cables
Refer to the display documentation for proper connection of the video cables, that is, from the display to the display
controller. After you make the connections, you can check that the cables are neatly routed and firmly attached to the cart.
1
Plug the power and video cables
into each display. The video cable for
the first display is marked with tape.
2
Plug the power cord into
the computer.
3
Plug the video cables into the
computer. (The cable for the first
display plugs into the top port.)
4
Plug the keyboard and mouse
cables into the computer.
SIX: Installing the Software
To finish the integration, install the display driver and the Dome CXtra software onto the computer hard drive. Install the
display driver before you install the software. Refer to the display or software documentation for more information.
5
Plug all power cords into the
power strip. Use the cable ties to
bundle and secure the cords and
cables. (If using a UPS, plug the power
cords into the power strip, plug the
strip cord into the UPS, and plug the
UPS cord into a grounded outlet.)
6
Plug the power strip cord into
a grounded outlet. Be sure that you
make the connection to the power
source last. Refer to the display
documentation before powering on
the system.
Warnings
• Use the cart only on flat surfaces.
• Do not use the cart within 6 feet of the patient.
• Always use caution when moving the cart. Use both hands to steer or maneuver the cart.
Do not use your feet to push or move the cart.
• Before transport, unplug power cords and data cables from wall outlets. Secure all cords and cables to
avoid tipping over and tripping upon the cart.
• Always lock the front wheels when the cart is not in use. Do not leave the cart unattended on an incline.
• Transport the cart from floor to floor by elevator. Do not move the cart by stairway.
• Routinely clean the cart wheels with a noncorrosive cleaning agent.
• When storing the cart with the displays attached, follow the environment specification provided in
the display documentation.
Tips
• Attach the excess length of the video cables to one side of the L-bracket and attach the excess length of
the power and peripheral cables to the other side.
• Use the hook on the back of the cart to coil the AC power cord when the system is not in use.
Cart Configurations Available
• Dome RP2 – Dual Planar PX212M displays with AX1 or EX2 board • Dome RE2c – Dual Dome E2c displays with AX1 board
• Dome RQ2 – Dual Dome Q2 displays with AX1 or EX2 board • Dome RE3 – Dual Dome E3 displays with AX3 or DX2 board
• Dome RC3 – Dual Dome C3i displays with DX2 board • Dome RE3c – Dual Dome E3c displays with AX3 or DX2 board
• Dome RE2 – Dual Dome E2 displays with AX1 or DX2 board • Dome RE4c – Single Dome E4c display with AX3 board
Left. Cart as shipped. This mobile
unit forms the base of all the display
configurations.
• Video and power cables prerouted.
• Cleanable keyboard and mouse
included.
• Binding materials provided
Right. Customer-provided computer and
UPS mounted on the cart.
America Sales
Planar Systems, Inc.
1195 NW Compton Drive
Beaverton, OR 97006-1992 USA
phone (503) 748-1100
fax (503) 748-1493
© 2006 Planar Systems, Inc. All rights reserved.
Planar, Dome, and CXtra are either registered trademarks or trademarks of Planar Systems, Inc. All other trademarks are
the property of their respective owners.
020-0336-02A
Medical Sales
Planar Systems, Inc.
400 Fifth Avenue
Waltham, MA 02451-8738 USA
phone (781) 895-1155
fax (781) 895-1133
Europe Sales
European Representative
Planar Systems, Inc.
Olarinluoma 9, P. O. Box 46
FIN-02201 Espoo, Finland
phone + 358 9 420 01
fax + 358 9 420 0200
Customer Support
•Go to www.planar.com
•E-mail medicalsupport@planar.com
• Call (866) PLANAR1 and select
Option 4.
Loading...