Planar Q2, Dome RP2, Dome RQ2, Dome RC2, Dome RC3 User Manual

Dome Surgery Review Cart

The portability of the Dome Surgery Review Cart allows you to implement a DICOM-compliant, PACS referral viewing station—
on demand—in any area of a healthcare facility. When it is fully integrated, the cart consists of the computer unit that you
supply and these components:

•Review cart for attaching a computer and two displays • Dome CXtra software for DICOM compliance

•Dual Dome displays for side-by-side image review • Cleanable keyboard and mouse

•Display controller and driver • Power adapters (display dependent)

To facilitate integration at your location, Planar has partially assembled the review cart by prerouting power and video cables.
You need only to install the display controller into your computer, attach the computer and the displays to the cart, and
connect the power and video cables. Check the display documentation for safety guidelines on handling the components.

System requirements

Check that the computer unit you are mounting to the cart
meets the requirements of the Dome displays, display
controller and driver, and Dome CXtra software.

Dome P2 or Q2 display using the EX2 display controller

•Intel Pentium 4/Xeon clocked at 2.0 GHz (or faster),
AMD Athlon/Opteron with 2000+ rating (or faster)

•Microsoft Windows XP or Windows 2000
operating system

•AGP 8X/4X bus with full height AGP slot: H 4.2"

• 256 MB system memory (512 MB or more
recommended)

• CD-ROM drive

• 300 Watt (or greater) power supply

Dome CX display using the DX or DX2 display controller

•Intel Pentium 4/Xeon clocked at 2.0 GHz (or faster),
AMD Athlon/Opteron with 2000+ rating (or faster), or
equivalent CPU

•Microsoft Windows XP or Windows 2000
operating system

•Full height half length PCI slot: H 4.2" x L 6.95"
(PCI64/66 slot recommended for maximum
performance)

• 256 MB system memory (512 MB or
more recommended)

• CD-ROM drive

• 200 Watt (or greater) power supply

Computer specifications

Your computer unit must not exceed these specifications:

•Weight – 35 lb (16 kg)

•Size (W x H x D) – 7.5" x 16" x 20"
(190 mm x 406 mm x 508 mm)

Here, dual Dome C3i displays are mounted to the cart.
Other display configurations may have variations for
power supply connection and peripherals.

ONE: Check the Package Contents

Confirm that you received these items.

•Box 1: Preconfigured cart, containing:
–Video and power cables (2 each),

routed

–Power supplies (2), mounted,

as required per display
–Keyboard and mouse
–Display mounts with VESA 100-mm

hole pattern, attached
–Power strip (4 outlets), mounted

and routed
–Computer straps (3)
–Tie cables (5)

•Box 2: Dual display unit
– Screws, Phillips buttonhead (8)
–Display controller
–Driver software
–Display documentation
–Dome CXtra Edition

Cart as shipped.

Video and power cables routed through
the column of the cart, keyboard and mouse,
and binding materials.

TWO: Install the Display Controller

Install the display controller into your computer before you attach the computer to the cart. Refer to the display
documentation for instructions.

THREE: Attach the Computer

Be sure to thread the straps through the slits on each side of the cradle and center the computer unit in the cradle.

1

Position the cart so that you face

the rear. Lock the front wheels.

4

Turn the two thumbscrews under­neath the unit counterclockwise to
extend the cradle.

2

Remove cables bundled on

the cradle.

5

Place the computer in the cradle
and push in the cradle extension to fit.
Retighten the thumbscrews.

3

Thread the straps through the slits

on the bottom of the cradle.

6

Secure the computer straps.
See “Tips” for how to secure larger
computer units.