Dome E4c Display
User’s Guide
© 2006 Planar Systems, Inc. All rights reserved.
Information in this document has been carefully checked for accuracy; however, no
guarantee is given to the correctness of the contents. This document is subject to
change without notice. Planar provides this information as reference only. Reference
to other vendors’ product does not imply any recommendation or endorsement.
This document contains proprietary information protected by copyright. No part of
this manual may be reproduced by any mechanical, electronic, or other means, in
any form, without prior written permission of the manufacturer.
Planar, Dome, E4c, CXtra, RightLight are either registered trademark or trademarks of
Planar Systems, Inc. All other trademarks are the property of their respective owners.
020-0436-00A
Product Information
The design of the Dome E4c digital display takes into account every
known measure to ensure your personal safety. Improper use of the
display can result in electric shock, fire, or damage to the display.
Read all instructions before setting up the display.
Classification:
Shock Protection: Class I.
Degree of Protection Against Electric Shock: No applied part.
Degree of Protection Against Harmful Ingress of Water:
Ordinary equipment (IPX0).
Degree of Safety in the Presence of Flammable Anaesthetic
Mixture with Air or with Oxygen or Nitrous Oxide:
Not suitable for use in the presence of a flammable
anaesthetic mixture with air or with oxygen or nitrous oxide.
Mode of Operation: Continuous.
Important recycle instruction:
LCD lamp(s) inside this product contain mercury. This
product may contain other electronic waste that can be
hazardous if not disposed of properly. Recycle or dispose
in accordance with local, state, or federal laws. For more
information, contact the Electronic Industries Alliance at
WWW.EIAE.ORG. For lamp-specific disposal information, check
WWW.LAMPRECYCLE.ORG.
Symbol explanations
DISPOSAL. Do not use household or municipal waste
collection services for disposal of electrical and
electronic equipment. EU countries require the
use of separate recycling collection services.
CAUTION. Read the accompanying text carefully, for
proper operation and maintenance of the display
system.
DANGEROUS VOLTAGE. Important precautions about
electric shock. Read the accompanying text carefully,
to prevent damage to components of the display
system and for your safety.
DIRECT CURRENT.
BAROMETRIC PRESSURE.
Maximum operating altitude, up
to 3,048 meters (10,000 feet). Maximum unpressurized
shipping and storage altitude, up to 12,192 meters
(40,000 feet).
RELATIVE HUMIDITY. Operating 10% to 90% (non-
condensing). Transport and storage 5% to 90%
(non-condensing).
TEMPERATURE. Operating 0° to 40° C. (Ambient air
temperature surrounding the display.) Transport and
storage -10° to 60° C. (NOTE: After shipping or storage,
allow display unit to reach room temperature before
powering on. Ambient room temperature ranges from
20° to 25° C (68° to 77° F).
Intended use
The Dome E4c display is an AMLCD unit designed for viewing medical
X-ray images. This unit should not be used near patients and should
be kept outside of 1.83 m perimeter and 2.29 m vertical.
This device must not be used in primary image diagnosis in
mammography.
CAUTION: Federal law restricts this device to sale by or on the order of
a medical practitioner.
iv | Dome E4c Display
Safety precautions
External equipment intended for connection to signal input, signal
output, or other connectors, must comply with the relevant IEC
standard (EN/IEC 60601-1 series for medical electrical equipment). In
addition, all such combinations (systems) must comply with the
standard IEC 60601-1-1, Safety requirements for medical electrical
systems.
Equipment not complying to IEC 60601 must be kept outside the
patient environment, as defined in the standard as at least 1.5 meters
from the patient or the patient support.
Any person who connects external equipment to signal input, signal
output, or other connectors has formed a system and is therefore
responsible for the system to comply with the requirements of IEC
60601-1-1. If in doubt, speak with a qualified technician.
Safety tips
• Never open the display case, even when the power is off. Do not drop or
push objects into the display case. Dangerous voltage inside may cause
electric shock or death.
• Use the grounded power supply and the video cable supplied by Planar.
Replace the power supply or video cable if damaged.
• Be sure the display is electrically grounded. Connect the third grounding
pin on the US power cord to a grounded outlet. The European power
cord does not have a third grounding pin, but it must be plugged into a
grounded outlet. If the power cord connects directly into the computer,
make sure the computer is grounded.
• Keep the display dry if it is part of a surgical system. The display lacks
protection against liquids or spills.
• Do not plug the power supply into an overloaded AC outlet or extension
cord. Overloaded AC outlets and cords can result in electric shock or fire.
• Unplug the power cord from the wall outlet during thunderstorms.
• Do not place magnetic devices, such as motors, near the display.
• In locations where 240V outlets are used, use the E4c display only on
a center-tapped, 240V, single-phase supply.
GROUNDING RELIABILITY CAN ONLY BE ACHIEVED WHEN EQUIPMENT IS
CONNECTED TO AN EQUIVALENT RECEPTABLE MARKED “HOSPITAL ONLY” OR
“HOSPITAL GRADE.”
Product Information | v
Unpacking and handling tips
The Dome E4c display is a precision instrument that requires proper
care to maintain adherence to specification. Unpack the display
carefully, then set up and handle the unit properly to avoid damage
to the LCD panel.
• Use both hands to grasp the display case when lifting it from
the shipping carton, but avoid touching the screen.
• Do not apply pressure to the screen or touch the screen with
bare fingers or objects. Pressure can affect image quality.
• Allow the display to warm to room temperature before turning it
on. Avoid sudden temperature changes in environment to prevent
condensation.
• Secure the display onto the Planar-supplied wall or cart mounting
hardware to ensure safety if you elect not to use the desk stand.
• Do not set up the display near strong light or heat sources.
• Do not block the vents on the display or install the display in a builtin enclosure. Blocked vents cause excessive heat inside the display.
• Do not remove the back cover or disassemble the display. There are
no user-serviceable parts inside.
Shipping/storing the display
Keep the display in its shipping container until installation. Return the
display to its original container whenever you need to store the unit,
move it to another location, or return it for repair.
vi | Dome E4c Display
Cleaning the display unit
Periodically wipe the display housing with a soft, dry cloth to prevent
dust and other material from clogging the venting holes.
The display screen can be damaged by excessive scrubbing and by
incompatible cleaning solvents. Dampen a clean, soft lint-free cloth
with distilled de-ionized water and wipe the screen gently. Use a
clean, soft, dry lint-free cloth to remove any residue.
To remove grease or other organic contaminants from the display
screen, use a 50% to 70% IPA (isopropyl alcohol) solution sparingly.
Never use acetone, as it can damage the antistatic hard coating and
void the warranty.
WARNING
DISCONNECT SUPPLY BEFORE SERVICING
AVERTISSEMENT
COUPER L’ALIMENTATION AVANT L’ENTRETIEN ET LE DEPANNAGE
Disposal information
Follow your local governing ordinance for proper disposal or
recycling of electronic components.
Product Information | vii
AMLCD panel mounted on desk stand
PCI Express
display controller
Dual-link
DVI cable
DC power adapter Power cords
Display driver and
Quick reference
calibration software
Options available: VESA wall-mounting kit and Dome Surgery Review Cart.
See page 8 for more information.
About the Display
The Dome E4c display is a 30-inch AMLCD color panel designed for
widescreen diagnostic imaging. The combination of high resolution
and high contrast ratio allow the viewing of color and grayscale
images simultaneously.
Bezel-free framing of 4 megapixels of data is presented in a landscape
resolution of 2560 x 1600 pixels. Gamma correction is achieved on
this true color display from a palette of 1786 near-gray values.
The integrated Dome RightLight Controller monitors and stabilizes
backlight luminance.
The display unit includes a PCI Express graphics card to support
the required dual-link connectivity for the display, and an external
power adapter.
System requirements
• Intel Pentium 4/Xeon; AMD Athlon 64/K7/XP or compatible
• PCI Express x16 lane slot
• 50 MB hard disk space
•256 MB RAM
•CD-ROM drive
• Power supply, 350 watts or greater
• Windows XP or Windows 2000 with Service Pack 4 or higher
Display components
The Dome E4c display has a light-emitting diode, or LED, on the front
panel to indicate display status.
• Green. The display is connected and running properly.
• Amber. The video signal is not being received
LED on display front
There is no power switch on the display unit. The unit turns on
automatically when the computer system is turned on. The LED
appears green to indicate functional system, or normal operation.
2 | Dome E4c Display
Improper cable connections could cause no image to appear on the
display screen or the LED to glow amber. See “Troubleshooting” on
page 9 for more information.
The ports for connecting the power cord and the video cable are on
the back. The power input port is an 8-pin DIN connector that drives
power to the display. The power input is 24V ±5% (115 W typical).
See detail below for pin assignment.
The dual-link DVI connector drives the data to the display. When the
DVI cable is disconnected, the display backlight turns off and the unit
enters power-saving mode.
Display brightness and power saving functions are controlled via the
Dome CXtra software. No other user-accessible controls are available.
DIN connector, left
Dual-link DVI connector, right
Pin assignment of DIN connector
VCC 8
VCC 7
VCC 6
VCC 5 3 GND
4 GND
1 GND
2 GND
8-pin connector on
Dome E4c display
About the Display | 3
Display Installation
Before you install the display controller, remove any existing graphics
card and its driver from your computer. After installation, the display
turns on automatically when you turn on your computer system.
WAR NING
In locations where 240V outlets are used, use the E4c display only on
a center-tapped, 240V, single-phase supply.
Turn off your computer before you install the board, but leave
the power cord plugged into the grounded outlet. Otherwise, you
could get an electric shock and cause damage to the components.
To prevent electrostatic discharge, take these precautions:
• Remove the controller slowly from its static-shielding bag.
• Wear an antistatic wrist strap.
• Repeatedly touch the power supply or the metal surface of
the computer chassis to discharge your body’s static electricity.
4 | Dome E4c Display
Installing the controller and display
1 Remove the computer cover and the blank bracket from
the available PCI Express slot.
2 Insert the display controller into the slot, align the connector pins,
and press the board down until it is firmly seated. Secure the
mounting bracket and reattach the cover.
3Plug the DC power cord into the power input port on the display.
Connect the dual-link DVI cable to the display.
4 Connect the DVI cable to the display controller installed in
the computer. Use video port #1. Plug the AC power cord into
the power adapter and into the grounded power outlet.
Remove the computer cover and
1 2
the PCI Express bracket.
Install the board and reattach the
cover.
Connect the power adapter cord and
3
the dual-link DVI cable to the display.
Connect the DVI cable to port #1 of the
4
installed controller and plug the power
cord to the grounded outlet.
Display Installation | 5
Installing the display driver
Before you install the driver, remove any previously installed display
driver for the display controller from your system.
1 Start the system. Click Cancel on the Found New Hardware Wizard.
Click No when the system prompts you restart the computer.
2 Insert the driver installation CD and run SETUP.EXE.
3Click Next.
4 Click Yes to the license agreement. The installation starts.
5 Follow the onscreen instructions to complete the installation.
Planar recommends that you select the Express installation option.
6 When the Setup complete message appears, select Yes, I want to
restart my computer now, and click Finish.
7 If the Digital Signature Not Found message appears, click Yes or
Continue to complete the driver installation.
Configuring the display
1 Right-click the desktop and select Properties > Settings.
2 Use the native resolution of the display.
3 Click OK until you return to the desktop.
Adjusting display properties
Use the Display Properties dialog to make changes to
the video settings.
6 | Dome E4c Display
Setting the display mode
1 Right-click the desktop and select Properties > Settings.
2 Select the monitor that you want to change. Then click Advanced.
3 Click the Monitor tab. Make sure that the check box for Hide modes
that this monitor cannot display is empty (unchecked).
4 Click the Adapter tab, then click the List All Modes button.
5 Choose the mode and click OK.
6Click Apply or OK.
Display information is read via the DDC interface between the
graphics board and the display interface board. The video board
driver configures timing parameters using the EDID of the display.
Any rotation support is provided by the display controller, which also
provides lookup table support for gamma correction.
Setting brightness
You must have the Dome CXtra software installed to change the
display brightness. Adjust the value of the white level on the
Backlight tab of the RightLight Panel Configuration.
Removing the driver
1 Close all applications that are running.
2 Navigate to the Control Panel. Select Add/Remove Programs.
3 Select your current graphics card drivers. Select Add/Remove.
Follow the wizard to remove your current display drivers.
4 Restart your system.
Display Installation | 7
Installing Dome CXtra
Bundled with the display system, the Dome CXtra software enhances
the functionality of the Dome E4c display with a range of value-added
services, such as DICOM calibration, error reporting, and backlight
saver. Network management of Dome displays running the Dome
CXtra software require the Enterprise Management Service for
Dome CXtra. For more information and instructions on installation,
refer to Dome CXtra User’s Guide.
Conserving energy use
You have two ways to lower energy usage when the display is idle:
• Dome CXtra Backlight Saver service (preferred)
• Screen Saver (set via Windows operating system)
Activate the power saver when you anticipate periods of inactivity,
such as at the end of the work day or work week. Once activated,
Backlight Saver (or Screen Saver) automatically turns the backlight off
during the period of inactivity. Backlight Saver and Screen Saver both
extend the life of the backlight and reduce the burn-in of images.
Do not use the Backlight Saver and Screen Saver concurrently.
Options available
8 | Dome E4c Display
The following options are available for the Dome E4c display.
• VESA (100 mm x 200 mm) wall-mounting kit
• Dome Surgery Review Cart
WARNING: Use only the mounting devices supplied by Planar to
attach the display to the wall unit or to the cart. Failure to use the
specified device or to follow the mounting instructions exactly
could be hazardous.
Troubleshooting
Problem Possible Cause Solution
Display does not light up. Power is not on. Make sure that the computer
is turned on.
Activate the computer from
sleep mode.
Power cord is not securely
connected.
No image appears on
the screen
Power LED is amber. Video cable is not securely
Video cable is not securely
connected.
fastened.
Tighten power cord
connection and turn on
computer.
Check to see that all cables
are properly connected to
the computer and to the
display.
Make sure that DVI cable is
connected to the video #1
port on the display
controller.
Turn off the computer. Make
sure that the video cable is
properly connected to the
display and to the display
controller.
Check the computer power
and graphics adapter
configuration.
Troubleshooting | 9
Specification
In locations where 240V outlets are used, use the E4c display only on a center-tapped,
240V, single-phase supply.
Category Characteristic Item Specification
Screen Screen size diagonal 756.228 mm (30 in.)
Interface Digital Video In DVI Rev. 1.0 digital dual-link connector
Input formats Landscape orientation 2560 x 1600 (24-bit color)
Physical Screen type AMLCD (active matrix liquid crystal display)
Power requirements Power supply 100 ~ 240 VAC 50 ~ 60 Hz universal Auto
Resolution 2560 x 1600 pixels (landscape)
Pixel pitch 0.2505 mm, 101 dpi
Pixel arrangement RGB vertical stripe
Active area 641.28 mm x 400.8 mm (25.25 in. x 15.78 in.)
Number of colors supported 16.7 million colors, 256 shades of gray from
a palette of 1786 near-gray shades
Refresh rate 60 Hz
Contrast ratio 600:1 (typical)
Brightness 300 cd/m
330 cd/m
Pixel rise/fall time 14 ms typical Black-White
Viewing angle ± 85° (170°) horizontal
Display control –
Brightness/contrast
Display identification EDID read using DDC2B+
Display status LED on front of unit
VGA/XGA 640 x 480 –1280 x 800
Protective glass Antistatic hard coating (3H)
Display size (without stand) 713 mm x 473 mm x 72 mm
Display weight (without stand) 12.7 kg (28 lb)
Mounting options Desktop stand (standard);
Input voltage +24 V ±5%
Power consumption 115 Watts typical
11 ms typical Gray-Gray
± 85° (170°) vertical
DDC2B+
(28.0 in. x 18.6 in. x 2.8 in.) nominal
100 mm x 200 mm VESA wall mount (optional)
Switching with Medical Approvals and PFC
2
(typical) – protective glass model
2
(typical) – open bezel model
10 | Dome E4c Display
Power supply
CAUTION: Use only the power adapter supplied with the E4c display unit
(JEC Korea Corporation, Type JMW1150KA2423F51).
Category Characteristic Item Specification
Power input
requirements
Power output
requirements
Physical Size 223.5 mm x 90 mm x 56.6 mm
Voltage selection Auto-ranging
Voltage 100 – 240V AC
Current 3.0 A
Frequency 47 to 63 Hz
Voltage 24 V DC
Current 6.25 A (150 W)
(8.8 in x 3.5 in x 2.2 in)
Weight 1.4 kg (3 lb)
±5%
Reliability
Characteristic item Specification
Display MTBF >50,000 hours
Backlight MTBF 50,000 hours typical
Environment
Characteristic item Specification
EMI shielding No emission of low-level radiation
Temperature operating 0° C to 40° C
storage -10° to 60° C
Humidity operating 10% to 90% Relative Humidity
(non-condensing)
storage 5% to 90% Relative Humidity
(non-condensing)
Specification | 11
Regulatory Compliance
Canada, European Union, United States
This display has been tested and
found to comply with IEC/EN
60601-1 and IEC/EN 60601-1-2
standards, and is certified to
meet medical standard C22.2
No. 601.1-M1990 (C US Mark).
The medical display, in addition to meeting medical requirements, has been
tested and found to comply with the limits for Federal Communications
Commission (FCC) Class B computing devices in a typically configured system
since many medical offices are located in residential areas. It is the system
integrator’s responsibility to test and ensure that the entire system complies
with applicable electromagnetic compatibility (EMC) laws.
Planar Systems, Inc. has made great efforts to support the medical device
industry, in particular, medical device manufacturers and medical device
system integrators. We offer state-of-the-art color displays that are compliant
with worldwide accepted medical device safety standards, and for the
European market, CE-marked displays based on compliance with counsel
directive 93/42/EEC—commonly referred to as the Medical Device Directive
(MDD). The following summarizes our qualification of these displays as it
relates to compliance with the MDD.
The European Medical Device Directive requires that the intended use of the
device be defined. The intended use of these displays is “to display
alphanumeric, graphic, and image data as inputted from any type of medical
device.” These displays do not provide a measurement function in any way,
and it is the device and systems manufacturer’s responsibility to verify its
function in the integrated device or system.
The display was classified as required by the MDD according to Annex IX of
the directive and the medical device (MEDDEV) guidance available at the time
of classification. Because the display uses electrical energy and has no direct
patient connections and—by itself—no medical utility, the display is
classified according to Rule 12 as an MDD Class I device, component, or
accessory. The MDD states that manufacturers of Class I medical devices or
accessories shall satisfy the requirements in regard to design and
manufacturing controls, that is, the applicable assessment route to be used
for CE-marking under the MDD, and it shall carry the CE mark according to
Annex XII of the directive, with no notified body annotation.
The applicable safety standards for an MDD Class I display are IEC/EN
60601-1:1990 along with Amendments 1 and 2. To help the medical device
designer evaluate the suitability of these displays, Planar has also conducted
EMC testing to IEC 60601-1-2 as it can be applied. The display with its power
supply alone does not represent a functional medical device. Hence, Planar
configured a minimal operating system to exercise the display. The resulting
data are made available to interested parties.
This is informative data, not certification data. Certification data must be
obtained by the device or system integrator according to Article 12 of the
MDD titled “Particular procedure for systems and procedure packs.”
Paragraph 2 clearly outlines the device or system integrator’s responsibility in
this matter.
In summary, Planar Systems, Inc. is CE-marking these displays under the
Medical Device Directive, which establishes compliance to the basic medical
safety standards. However, EMC compliance can only be accomplished in the
configured medical device or system and is the responsibility of the device or
system manufacturer. Planar has the necessary documentation such as IEC
60601-1 notified body and other third-party test reports and certifications, a
risk/hazard analysis, an essential requirements checklist, and the Planar
International Electrotechnical Commission (IEC) declaration of conformity.
Planar Systems, Inc., located in Beaverton, Oregon, USA, is the manufacturer
of these displays in the meaning of the directive. As required by the MDD in
Article 14, Planar Systems, Inc., not residing in the European Economic Area
(EEA), has a European representative, Planar Systems, Inc.—Olarinluoma 9,
P. O. Box 46, FIN-02201 Espoo, Finland (phone + 358 9 420 01;
fax + 358 9 420 0200).
In the opinion of Planar Systems, Inc. registration required to put this device
into commerce is the responsibility of the medical device/
system
manufacturer, and Planar supports this requirement by providing a
European Commission (EC) declaration of conformity. If Planar
supplies a display to an end user, rather than a device manufacturer, it
is the end user’s responsibility to ensure continued compliance with
the MDD of the system in which the display is integrated.
The supplier will make available on request, circuit diagrams, component part
lists, etc.
For vigilance reporting as required under Article 10 of the MDD, Planar
Systems, Inc. will provide any information requested by competent authority
to support any reported incident investigation by such an authority.
EU Declaration of Conformity for Medical Application
A Declaration of Conformity has been filed for this product. For
additional copies of the Declaration of Conformity document,
contact Planar Systems.
The Dome E4c digital flat-panel display meets the essential health
and safety requirements, is in conformity with, and the CE marking
has been applied according to the relevant EU Directives listed below,
using the relevant section of the following EU standards and other
normative documents;
EU EMC Directive 89/336/EEC
EU Electromagnetic Compatibility Directive
EN 60601-1-2 (2001)
Medical Electrical
Equipment
EN 55011 (Class B) Limits and methods of measurements for radio
IEC 1000-3-2 Harmonic emissions
IEC 1000-3-3 Voltage fluctuations/flicker emissions
IEC 1000-4-2 Electrostatic discharge requirements for industrial
IEC 1000-4-3 Radiated electromagnetic field requirements for
IEC 1000-4-4 Electrically fast transients for industrial process
IEC 1000-4-5 Surge requirements
IEC 1000-4-11 Voltage variations/dips/interrupts
IEC 1000-4-6 Conducted immunity
IEC 1000-4-8 Magnetic field immunity
EN 60601-1 Medical
Electrical
Equipment
Section 1.2. Collateral standard electromagnetic
compatibility requirements
interference characteristics of industrial, scientific,
and medical equipment
process measurement and control equipment
industrial process measurement and control
equipment
measurement and control equipment
Conformance to the Medical Device Directive 93/
42/EEC
Part 1: General requirements for safety
U.S. FCC Compliance Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications to this equipment not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Standard Warranty
Summary
• Standard one-year “repair-and-return” warranty
•Two-year backlight warranty
• Typical repair turnaround time of 10 business days
Standard Warranty Return Procedure
As a Planar Standard Warranty customer, you must follow the procedure below if you
have a non-functioning Dome E4c display. The Planar customer service staff will
attempt to correct any minor issues that may be causing the problem. Once Planar has
determined that you have a non-functioning product, Planar will arrange for return and
repair of the non-functioning product.
1 Contact Planar via the web at http://www.planar.com/support. In North America,
call (866) PLANAR1 (866.752.6271). In Europe, call +358 9 420 01 or send your info by
fax to +358 9 420 0200. Have the model number, serial number, and proof-ofpurchase available.
2 Planar customer service staff will attempt to correct any minor issues that may be
causing the problem. If we are unable to correct the problem to your satisfaction, we
will issue a Return Material Authorization (RMA).
3 You must return the product, as specified, to Planar Systems. Planar will validate the
defect, repair the unit, and return the unit to you. The typical turnaround time is
10 business days.
*
* If, within 2 years of initial purchase, the maximum output of
the Dome E4c display is determined by Planar Systems to be less than 175 cd/m
Planar will repair or replace the display at its sole discretion.
2
,
Summary Limitations and Exclusions of Dome Displays
1 Customer must provide original proof of purchase of the display system.
2 Warranty is void on any product with a defaced, modified, or removed
serial number.
3 Warranty is void on any product with damage, deterioration, or malfunction
resulting from the following:
a) Accident, misuse, neglect, fire, water, lightning, or other acts of nature,
unauthorized product modification, or failure to follow instructions supplied with
the product.
b) Repair or attempted repair by anyone not authorized by Planar.
c) Any damage of the product due to shipment.
d) Removal or installation of the product.
e) Causes external to the product, such as electric power fluctuations or failure.
f) Use of supplies or parts not meeting Planar's specifications.
g) Normal wear and tear.
h) Any other cause, which does not relate to a product defect.
4 Warranty excludes removal, installation, and setup service charges.
Limitation of Implied Warranties
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Exclusion of Damages
THE LIABILITY OF PLANAR IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF
THE PRODUCT. PLANAR SHALL NOT BE LIABLE FOR THE FOLLOWING:
1 DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT,
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF
TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL,
INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS,
EVEN IF ADVISED OF THEIR POSSIBILITY OF SUCH DAMAGES.
2 ANY OTHER DAMAGES, WHETHER INCIDENTAL, INDIRECT, CONSEQUENTIAL OR
OTHERWISE.
3 ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
Effect of Local Law
This warranty gives you specific legal rights, and you may have other rights, which vary
from locality to locality. Some localities do not allow limitations on implied warranties
and/or do not allow the exclusion of incidental or consequential damages, so the
above limitations and exclusions may not apply to you.
America Sales
Planar Systems, Inc.
1195 NW Compton Drive
Beaverton, OR 97006-1992 USA
(503) 748-1100 phone
(503) 748-1493 fax
Medical Sales
Planar Systems, Inc.
400 Fifth Avenue
Waltham, MA 02451-8738 USA
(781) 895-1155 phone
(781) 895-1133 fax
medicalsales@planar.com
medicalsupport@planar.com
www.planar.com
Europe & Asia-Pacific Sales
European Representative
Planar Systems, Inc.
Olarinluoma 9, P. O. Box 46
FIN-02201 Espoo, Finland
+ 358 9 420 01 phone
+ 358 9 420 0200 fax
vertrieb@planar.com
medicalsupport@planar.com
www.planar.com
Asia-Pacific Sales
Planar Systems, Inc.
388 Nan Jing West Road, Suite 3905
Shanghai Peoples Republic of China
+ 86 21 6334 5050 phone
+ 86 21 6334 6339 fax
sales @planar.com.cn
support@planar.com.cn
www.planar.com.cn
Loading...