Planar Dome E2c User Manual 2

Dome E2c Display
Quick Reference
Windows XP Windows 2000
Read all instructions before setting up the Dome E2c display. Improper use of the display can result in electric shock,  re, or damage to display components.
For more product information, go to www.planar.com/support.
System Requirements
Intel Pentium 4/Xeon;
PCI Express x16 lane slot
50 MB hard disk space
256 MB RAM
CD-ROM drive
Power supply, 350 watts
or greater
Windows XP or Windows 2000
with Service Pack 4 or higher
Warning
Avertissement
Avvertenza
Advertencia
Wear an antistatic heel or wrist strap when installing the controller and display to avoid damage to computer components.
Warnung
2
Unpacking the Display
Check the contents of your Dome E2c display package for all the items shown here. Save the original packaging materials for storage and shipping.
Video card
Dome E2c display
Also included: Composite Video, S-Video, and VGA cables.
Power adapter
Power cord Software CDs
DVI cable
3
Display Components
The high-bright UXGA 1200x1600 AMLCD panel is sized to a 541 mm (21.3 in.) display screen. The reset button, LED indicator, and input power and video ports are located on the back of the display. No other user-accessible controls are available.
You can change the brightness of the Dome E2c display in the Display Properties dialog of the Windows operating system. However, when DICOM auto-calibration is running, you must control display bright­ness via the Dome CXtra software.
NOTE: Diagnosis requiring calibration with the Dome CXtra software can only be supported on the DVI-D interface.
Front view
2-megapixel AMLCD screen
4
Back view
2
1 3 4 5 6 7
8 9
Legend
1 Reset. Restores default
display setting.
2 LED indicator. Shows
display status.
3 DIN 8-pin port. Drives
power to the display.
4 S-Video, separate video
analog input port. Requires a 4-pin mini-DIN connector.
5 C-Video, composite
video analog input port. Requires an RCA or phono connector.
6 DVI, DVI-I video input port.
Supports DVI-D digital or DVI-A analog video. Requires DVI connector.
7 VGA. VGA video analog
input port. Requires an HD15 D-Sub or VGA connector.
8 USB-B port 9 USB-A port (2)
5
Installing the Display Controller
Remove any existing graphics card and its driver from your computer system before you install the controller and driver. Also disable any onboard graphics capability on the motherboard. See safety precautions on page 2.
To install the controller
1 Turn o your computer and all
peripherals. Disconnect all cables from your computer. Leave the power cord plugged into the
grounded outlet. 2 Remove the computer cover. 3 Remove any existing graphics card
and video signal cable, if necessary. 4 Remove the blank bracket from the
available PCI Express slot. 5 Insert the controller into the
slot, align the connector pins,
and press the board down until
it is  rmly seated. 6 Secure the mounting bracket. 7 Reattach the computer cover
and the peripherals.
Blank bracket
Open PCI Express slot
Controller installed
6
Connecting the Display
Use only the cables and power cord supplied with your display.
To connect the display
1 Plug one end of the DVI signal cable to
the DVI port on the display. Tighten the
thumbscrews to secure the connection. 2 Plug the power cord into the power
connector on the connector plate. 3 Plug the other end of the DVI cable
into the video port on the installed
controller. (Use DVI port #1 for
the  rst display if you are installing
only one display.) 4 Plug the other end of the power
cord into a grounded outlet. 5 Repeat steps 1 to 4 to
connect a second display
to the controller. 6 Power on your
display  rst,
then the
computer.
DVI
port 2
DVI
port 1
Power cord DVI cable
DVI cable
Controller installed
Connection
for a single
display or
the  rst display of a dual setup
7
Installing the Display Driver
Upon restarting your computer system, you must log on with administrator privileges. On Windows 2000 systems, Service Pack 4 or higher must be installed.
To install the display driver
1 Start the system. Click Cancel on the Found New Hardware Wizard dialog box. 2 Insert the Planar Installation CD and run the SETUP.EXE utility. 3 Click Next on the Welcome dialog. 4 Click Yes to the license agreement. The installation starts. 5 Follow the onscreen instructions to complete the installation.
Planar recommends that you select the Express installation option.
6 When the Setup complete message appears, select Yes, I want to restart
my computer now and click Finish.
To con gure the display
1 Right-click the desktop and select Properties > Settings. 2 Use the native resolution of your display. 3 Click OK until you return to the desktop.
8
Adjusting the Display Properties
Use the Display Properties dialog to make changes to the video settings or to set up dual-display con guration.
To set the display orientation
1 Right-click the desktop and select Properties > Settings. 2 Select the monitor that you want to change. Then click Advanced. 3 Click the Monitor tab. Make sure the check box for Hide modes that this
monitor cannot display is empty (unchecked).
4 Click the Rotation tab.
• Check Standard Landscape for landscape mode.
• Check Rotate 90 Left or Right for portrait mode.
5 Click Yes to save the setting. Then click OK until to return to the desktop.
To use a dual-display con guration
1 Right-click the desktop and select Properties > Settings. 2 Click the monitor icon 2. Then select Extend my Windows desktop
onto this monitor. 3 Set the resolution and color quality for the second display. 4 Click Apply or OK.
9
Handling the Display
Set up your display on a stable,
level surface away from any direct light or heat source, but near a grounded AC outlet.
Choose a well-ventilated location
with an adequate amount of space. Do not block the vents on the back of the display.
Never lift the display by the desk
stand. Use both hands to lift or move the display. Avoid touching the screen.
Never apply pressure to the screen
or touch the screen with bare  ngers or with any objects.
Allow the display unit to reach room
temperature before powering on.
Avoid sudden temperature changes
in the environment, as this may cause condensation, which damages the display.
Never remove the back cover or
disassemble the display. There are no user-serviceable parts inside.
In locations where 240V outlets
are used, connect the Dome E2c display only to a center-tapped, 240V, single-phase supply.
When troubleshooting, check that
all cables are properly connected and that your computer is turned on and not in power-saving mode.
Follow your local governing
ordinance for proper disposal or recycling of electronic components.
10
Cleaning the LCD Screen
Use a dry, clean, lint-free cotton cloth to remove surface dust from the display screen. Do not use chemically treated dust cloths.
To remove grease or organic contaminants, follow this procedure:
1 Disconnect the power supply from the display. 2 Dampen a soft, clean cloth with a small amount
of isopropyl alcohol.
3 Wipe the display screen gently with the
dampened cloth.
4 Use a dry, clean, lint-free cotton cloth to wipe
o the residue.
Do not spray or use acetone, toluene, or harsh solvents on the display case or screen. Chemical cleansers may cause damage to the display.
Do not touch the LCD screen with your  ngers. Skin oils are hard to remove from the screen.
Do not saturate the cleaning cloth. Liquid that drips on the glass may seep into the display case.
11
America Sales
Planar Systems, Inc. 1195 NW Compton Drive Beaverton, OR 97006-1992 USA
(503) 748-1100 phone (503) 748-1493 fax
Medical Sales
Planar Systems, Inc. 400 Fifth Avenue Waltham, MA 02451-8738 USA
(781) 895-1155 phone (781) 895-1133 fax
Customer Support
Visit www.planar.com E-mail: medicalsupport@planar.com Call (866) PLANAR1
Europe Sales
European Representative Planar Systems, Inc. Olarinluoma 9, P. O. Box 46 FIN-02201 Espoo, Finland
+ 358 9 420 01 phone + 358 9 420 0200 fax vertrieb@planar.com medicalsupport@planar.com www.planar.com
Asia-Pacifi c Sales
Planar Systems, Inc. 388 Nan Jing West Road, Suite 3905 Shanghai Peoples Republic of China
+ 86 21 6334 5050 phone + 86 21 6334 6339 fax sales@planar.com.cn support@planar.com.cn www.planar.com.cn
For more information, download the Dome E2c display manual from the Planar web site.
© 2006 Planar Systems, Inc. Planar, Dome, Dome E2c, and Dome CXtra are either registered trademarks or trademarks of Planar Systems, Inc. Technical information in this document is subject to change without notice. 020-0458-00A
Loading...