Planar AX3 Quick Reference

AX3 Display Controller
QUICK REFERENCE
Windows XP Windows 2000
020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 1
Experienced users and system administrators can follow the instructions in this document to install the AX3 display controller. This board provides dual display functionality.
Check the system requirements and the safety precautions on page 3. Then follow this order of installation for the Dome display system.
1 Install the AX3 display controller into your computer.
2 Connect one or two displays to the display controller.
3 Install the display driver.
4 Configure the display(s).
5 Install the Dome CXtra software.
For more information, refer to the user’s manuals for the display and the Dome CXtra software.
2
020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 2
Before You Begin
Check that your system meets these requirements and runs one of these Microsoft operating systems.
Warning
Avertissement
Avvertenza
Advertencia
Warnung
Before disconnecting a peripheral or removing a component from the motherboard, wait 20 seconds after unplugging the power cord to avoid possible damage to the motherboard.
Wear an antistatic heel or wrist strap when installing the board to avoid damage to computer components.
Discharge your body’s static electricity by touching the power supply or the metal surface of the computer chassis.
3
Operating System
Windows XP or Windows 2000 with Service Pack 4 or higher
System Requirements
Intel Pentium 4/Xeon; AMD Athlon 64/K7/XP or compatible
PCI Express x16 lane slot
50 MB hard disk space
256 MB RAM
CD-ROM drive
Power supply,
350 watts or greater
EX Display Display Controller
Dome E3 AX3
Dome E3c
Dome E4c
020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 3
4
Installing the Display Controller
1
Open PCI Express slot
AX3 controller
installed
Blank bracket
Remove any existing graphics card and its driver from your computer system before you install the AX3 controller and driver. Also disable any onboard graphics capability on the motherboard. See safety precautions on page 3.
To install the controller
1 Turn off your computer and all peripherals.
Disconnect all cables from your computer. Leave the power cord plugged into the grounded outlet.
2 Remove the computer cover.
3 Remove any existing graphics card and
video signal cable, if necessary.
4 Remove the blank bracket from the available
PCI Express slot.
5 Insert the controller into the slot,
align the connector pins, and press the board down until it is firmly seated.
6 Secure the mounting bracket.
7 Reattach the computer cover and the peripherals.
020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 4
Use only the cables and power cord supplied with your display.
To connect the display
1 Plug one end of the DVI signal cable to
the DVI port on the display.Tighten the thumbscrews to secure the connection.
2 Plug the power cord into the power
input port.
3 Plug the other end of the DVI cable into
the video port on the installed controller. (Use DVI port #1 for the first display if you are installing only one display.)
4 Plug the other end of the power cord
into a grounded outlet.
5 Repeat steps 1 to 4 to connect a second
display to the controller.
6 Power on your display first, then
the computer.
5
Connecting the Display
2
Connection
for a single
display or the
first display of
a dual setup
DVI cable
AX3 controller
installed
DVI port 1
DVI port 2
020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 5
6
Installing the Display Driver
3
Before you install the driver, remove any previously installed display driver for the display controller from your system.
To install the driver
1 Start the system. Click Cancel on the Found New Hardware Wizard. Click No when the
system prompts you to restart the computer. 2 Insert the driver installation CD and run SETUP.EXE. 3 Click Next. 4 Click Yes to the license agreement.The installation starts. 5 Follow the onscreen instructions to complete the installation. Planar recommends that
you select the Express installation option. 6 When the Setup complete message appears, select Yes, I want to restart my computer
now and click Finish. 7 If the Digital Signature Not Found message appears, click Yes or Continue to complete
the driver installation.
020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 6
7
Use the Display Properties dialog to make changes to the video settings.
To set the display mode manually
1 Right-click the desktop and select Properties > Settings. 2 Select the monitor that you want to change.Then click Advanced. 3 Click the Monitor tab. Make sure that the check box for Hide modes that this monitor
cannot display is empty (unchecked). 4 Click the Adapter tab, then click the List All Modes button. 5 Choose the mode and click OK.Then click Apply or OK.
To set the brightness
You must have the Dome CXtra software installed to change the display brightness. Adjust the value of the white level on the Backlight tab of the RightLight Panel Configuration.
Adjusting the Display Properties
4
020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page 7
020-0424-00A-AX3-QRUG 11/16/05 8:59 PM Page a
America Sales
Planar Systems, Inc. 1195 NW Compton Drive Beaverton, OR 97006-1992 USA
phone + 1 (503) 748-1100 fax + 1 (503) 748-1493
Medical Sales
Planar Systems, Inc. 400 Fifth Avenue Waltham, MA 02451-8738 USA
phone + 1 (781) 895-1155 fax + 1 (781) 895-1133
Europe Sales
European Representative Planar Systems, Inc. Olarinluoma 9, P. O. Box 46 FIN-02201 Espoo, Finland
phone + 358 9 420 01 fax + 358 9 420 0200
Asia-Pacific Sales
Planar Systems, Inc. 388 Nan Jing West Road, Suite 3905 Shanghai Peoples Republic of China
phone + 86 21 6334 5050 fax + 86 21 6334 6339
Customer Support
Visit www.planar.com
E-mail medicalsupport@planar.com
Call (866) PLANAR1
Copyright © 2005 Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc. Technical information in this document is subject to change without notice. 020-0424-00B
Loading...