Pixsys TCT101-1ABC User Manual

Download

CN1

1 6

MEMORY C.121

TCT101

1 2 3

Dima di foratura

28.5 x 70.5 mm

Frontal panel cut-out

Spessore suggerito 2 mm

Suggested thickness

÷8

77 mm

35 mm

53 mm

42mm

Enter

Memory Card

CN1

1 6

PI XSY S

Memory Card (optional)

with battery

Cod. MEMORY C243

Memory Card (optional)

Cod. MEMORY C121

Guarnizione per 32x74 Cod. 1600.00.082 (optional)

Gasket for 32x74

USER MANUAL TCT101-1ABC

PIXSYS www.pixsys.net

e-mail: sales@pixsys.net - support@pixsys.net

Software V 2.00

2300.10.120-RevB 091109

*2300.10.120-B*

Operating

conditions

Sealing

Material

Digital inputs

Outputs

Back-UP

Programming

software

Power supply

TECHNICAL DATA

0-40°C, humidity 35..95uR%

Front panel IP65 (with optional gasket) , Box IP30, Terminal blocks IP20

Polycarbonate UL94V0 self-exstinguishing

3PNP/NPN selectable, also analogic for potentiometers

2 relays 5A resistive

Rechargeable battery, approx 7days autonomy

Labsoftview 2.0

24...230Vac/Vdc +/-15% 50/60Hz / 2W

DIMENSION and INSTALLATION

INTRODUCTION

Thanks for choosing a Pixsys device.

Timer TCT101 can be set in 5 different modes: Timer-ON, Timer-OFF, Pause-Work, Oscillator, PWM (time-proportioned output), all options with independent setting of ON-OFF time. 3 digital inputs are available (NPN/PNP) for external commands like Start, Stop, Reset; one input is also analogic in order to allow the modification of working times by external potentiometer. 5 different time bases (hundredths, tenths, seconds, minutes, hours). Counting can be incremental or decremental.

MEMORY CARD (optional)

Parameters and setpoint values can be copied from one device to another using the Memory car

There are two methods:

With the device connected to the power supply

insert the memory card when the controller is off.

On activation display 1 shows and display 2 shows

The device loads the new data and starts again

With the controller disconnected from the power supply:

The memory card is equipped with an internal battery with a life of about 1000 uses.

Insert the memory card and press the programming button.

When writing the parameters, the LED turns red and on completing the procedure it changes to green. It is possible to repeat the procedure.

To update the memory card values, follow the procedure described in the first method, setting display 2 to so as not to load the parameters on controller.

Enter configuration and change at least one parameter. Exit configuration. Changes are saved automatically.

LOADING DEFAULT VALUES

This procedure restores the factory settings of the instrument.

(Only if the values stored on Mmeory Card are correct).

By pressing the key display 2 shows

Confirm using the key .

UPDATING MEMORY CARD.

PRESS

for 3 seconds

Display 1 shows

and 1st digit flashes,

display 2 shows

EFFECT OPERATION

Modify flashing digit,

press to reach the following digit

Enter password

to confirm

Display shows first parameter

of configuration table

WIRING DIAGRAM

GND

POSITIVO

OUTPUT

POTENZIOMETER 5..10 Kohm Accuracy 1000 points

Proximity sensor PNP 3 3wires

Proximity sensor PNP 2 2wires

Proximity sensor PNP 1 2wires

PNP

NPN

P-01 Timer Function

Timer On Timer Off Pause/Work Oscillator PWM

FUNCTION CONFIGURATION

P-02 Power-off Memory

Disable Only Timer Timer / State

BACKUP MEMORY CONFIGURATION

P-03 Hardware Input 1

INPUT CONFIGURATION

LIST of PARAMETERS

PNP

NPN

To modify Set1 or Set2 by external potentiometer follow the steps below:

1- use potentiometers 5kOhm to 10kohm 2- connect cursor to pin I3; a wrong connection may damage the potentiometer and lead to lock of the device. 3- accuracy on input is max 1000 points, therefore set the parameters "Upper limit" and "Lower limit" with a max difference of 1000 units.

(Ex.: LoS1 to 50,0 and uPS1 to 150,0 to modify time value related to Set1 between 50 and 150 seconds with steps of one tenth). Greater differences would make unstable the less significant digit.

4- To calibrate the scale of potentiometer enter the configuration mode and select:

Hin.3 as Pot Fin.3 as Set1 or Set2 P.tAr as Enable Exit configuration mode and place potentiometer at minimum level and press key, then place potentiometer at max level and press premere key: the device automatically exit the calibration procedure. N.B.: A switch-off of the device would interrupt the calibration.

Potentiometer:

Timer operating modes

Activate output at elapsing of counting Deactivate output at elapsing of counting T1 and T2 start in sequence T1 and T2 start in sequence and cycling Activate a percentage of output on a fixed time base

Memory after switch-off

Disabled Memory stores only value of Timer Memory stores value of Timer and START/STOP status

NPN PNP TTL

P-04 Hardware Input 2

Configuration Input 1

NPN PNP TTL

Configuration Input 2

Default

SETPOINT CONFIGURATION

OUTPUT CONFIGURATION

DISPLAY CONFIGURATION

P-05 Hardware Input 3

P-06 Active State Input 1

P-07 Active State Input 2

P-08 Active State Input 3

PNP TTL Potent.

High Level Low Level Rising edge

Configuration input 3

Activate Input 1

Activate Input 2

Activate Input 3

PNP TTL Potentiometer

High level Low level Rising edge

P-09 Function Input 1

P-12 Function Key UP

P-10 Function Input 2

P-11 Function Input 3

P-16 Format Set 1

P-18 Display Set 1

P-17 Format Set 2

P-19 Display Set 2

P-13 Output Q1 Setup

P-14 Output Q2 Setup

P-15 Type of Timer

Disable Start / Stop Start / Stop-Reset Reset-Start / Stop Reset / Start / Stop

Second.Cent Second.Decimal Second Minute.Second Hour.Minute

Disable Start / Stop Start / Stop-Reset Reset-Start / Stop Reset / Start / Stop Reset Wait Hold

Disable Out Timer 1 n.o. Out Timer 1 n.c. Out Timer 2 n.o. Out Timer 2 n.c. Start Stop

Incremental Decremental

Disable Visualized Modifiable

Disable Enable

P-24 Potent. tarature

P-20 Lower limit Set 1

P-21 Upper limit Set 1

P-22 Lower limit Set 2

P-23 Upper limit Set 2

Disable Reset

Disable Wait Hold Potent. To SET1 Potent. To SET2

Function of Input 1

Function of key

Function Input 2

Function Input 3

Format of counting

Visualization of Set 1

Format of counting

Visualization of Set 2

Setting of output Q1

Setting of output Q2

Counting mode

Disabled Start / Stop Start / Stop-Reset Reset-Start / Stop Reset / Start / Stop

Seconds, Hundredths Seconds, Tenths Seconds Minutes, Seconds Hours, Minutes

Disabled Start / Stop Start / Stop-Reset Reset-Start / Stop Reset / Start / Stop Reset Wait (stop the counting) Hold (hold value on display but counting goes on)

Disabled Output Timer 1 N.O. Output Timer 1 N.C. OutputTimer 2 N.O. Output Timer 2 N.C. Start Stop

Disabled Output Timer 1 N.O. Output Timer 1 N.C. Output Timer 2 N.O. Output Timer 2 N.C. Start Stop

Incremental Decremental

Disabled Visualized Visualized and modifiable

Disabledd Enabled

Calibration of potentiometer

Low limit Set 1

Upper limit Set 1

Low limit Set 2

Upper limit Set 2

Reset

Disabledd

Wait (stop the counting) Hold (Hold value on display but counting goes on) Modify SET1 by potentiometer Modify SET2 by potentiometer

Disabled

Default

0.0

99.9

Default

PRESS

for 3 seconds

Display 1shows

and 1st digit flashes,

Display 2 shows

EFFECT

OPERATION

Modify the flashing digit,

press to reach the next digit

Enter password

to confirm

The device loads default values

(factory settings)

Switch-off and restart

the device

Scroll the parameters

Increade or decrease value on display

by pressing and one of the arrow keys

at same time

Enter new data

which will be stored

releasing the keys

+ Or

End of configuration,

the device exits programming mode.

MODIFY PARAMETERS

LOADING DEFAULT SETTINGS

PRESS

Display SETPOINT 1 / 2

EFFECT

Modify selected SETPOINT

Select the chosen digit

Modify the flashing digit of the selected setpoint

MODIFY SETPOINT

Timer On Stop/Reset Start/Stop/Reset Reset Wait/Hold/Set1-2

Timer Off

Start/Stop/Reset Reset Wait/Hold/Set1-2 Start/Stop/Reset/Wait/Hold

Oscillator

Start/Stop/Reset Reset Wait/Hold/Set1-2 Start/Stop/Reset/Wait/Hold

PWM

Start/Stop/Reset Reset Wait/Hold/Set1-2 Start/Stop/Reset/Wait/Hold

Pause / Work

Start/Stop/Reset Reset Wait/Hold/Set1-2 Start/Stop/Reset/Wait/Hold

TCT101-1ABC “TIMER”

P-01

Timer

Function

Timer On Timer Off Pause/Work Oscillator PWM

FUNCTION CONFIGURATION

P-02

Power-off

Memory

Disabled Only Timer Timer / State

POWER-ON

RESET

BACKUP MEMORY CONFIGURATION

Timer value Out Timer 1 Out Timer 2

Start/Stop/Reset/Wait/Hold Set1 Set2

Stop/Reset

Set1 Set2

Stop/Reset

Set1 Set2

Stop/Reset

Set1 Set2

Stop/Reset

Set1 Set2

P-06

Active State

Input 1

High Level Low Level Rising edge

Disable Start / Stop Start / Stop-Reset Reset-Start / Stop Reset / Start / Stop

P-09

Function

Input 1

P-03

Hardware

Input 1

NPN PNP TTL

Disabled Start / Stop Start / Stop-Reset Reset-Start / Stop Reset / Start / Stop Reset Wait Hold

P-12

Function

Key UP

P-07

Active State

Input 2

High Level Low Level Rising edge

P-04

Hardware

Input 2

NPN PNP TTL

Disabled Reset

P-10

Function

Input 2

P-08

Active State

Input 3

High Level Low Level Rising edge

P-05

Hardware

Input 3

PNP TTL Potent.

Disabled Wait Hold Potent. To SET1 Potent. To SET2

P-11

Function

Input 3

P-24

Potentiometer

calibration

Disable Enable

INPUT CONFIGURATION

Second,Hundredth Second,Tenth Second Minute,Second Hour.Minute

P-16

Format

Set 1

Disabled Visualized Modifiable

P-18

Display

Set 1

P-20

Lower limit

Set 1

P-21

Upper limit

Set 1

Disabled Visualized Modifiable

Second,Hundredth Second,Tenth Second Minute,Second Hour,Minute

P-17

Format

Set 2

P-19

Display

Set 2

P-22

Lower limit

Set 2

P-23

Upper limit

Set 2

SETPOINT CONFIGURATION

Timer value Out Timer 1 Out Timer 2

P-13

Output Q1

Setup

Disabled Out Timer 1 n.o. Out Timer 1 n.c. Out Timer 2 n.o. Out Timer 2 n.c. Start Stop

P-14

Output Q2

Setup

Disabled Out Timer 1 n.o. Out Timer 1 n.c. Out Timer 2 n.o. Out Timer 2 n.c. Start Stop

OUTPUT CONFIGURATION

DISPLAY CONFIGURATION

P-15 Type

of Timer

Incremental Decremental

123

SetSet

SET1

Time

1 0

Out Timer 1

Start

Stop

Reset

TIMER 1

1 0

SetSet

SET1

Time

1 0

Out Timer 1

Start

Stop

Reset

TIMER 1

1 0

SetSet

SET1

Time

1 0

Out Timer 1

Out Timer 2

Start

Stop

TIMER 1

1 0

SET2

TIMER 2

SetSet

SET1

Time

1 0

Out Timer 1

Out Timer 2

Start

Stop

TIMER 1

1 0

SET2

TIMER 2

SetSet

SET2 (Period)

Time

1 0

Out Timer 1

Out Timer 2

Start

Stop

TIMER 1

1 0

SET1(% duty-Cycle)

In PWM mode, the only option available on parameters 16 and 17 for format of SET1 and SET2 is (seconds). Low and upper limits for SET1 (related to percentage of work or Duty Cycle) are allowed in the range 0 ... 100 (%).

ERROR in WRITING of EEPROM Memory (Note

TABLE of ERROR MESSAGES

Note 1: Switch the device off and restart it; if error is still notified, contact technical service

Note 2:

Discharged battery: keep the device connected to power supply in order to recharge the battery.

ERROR in READING of EEPROM Memory

Incorrect parameters (Note 1)

Incorrect calibration data (Note 1)

Incorrect status data (Note 1) Incorrect BACKUP registersI (Note 2)

Pixsys TCT101-1ABC User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual