PiXORD
Dual Streaming Network Camera /
Video Server
P-500/1500
User’s Manual
Version: 1.0
Date: 02/20/2008
- 1 -
CONTENTS
CHAPTER 1 INTRODUCTION................................................................................................................................- 2 -
1. WHAT IS PIXORD DUAL STREAMING NETWORK CAMERA/VIDEO SERVER?.....................................................- 2 -
2. FEATURES..........................................................................................................................................................- 3 -
CHAPTER 2 PHYSICAL IMAGES.......................................................................................................................... - 4 -
1. P1500 VIDEO SERVER.......................................................................................................................................- 4 -
2. P500 NETWORK CAMERA .................................................................................................................................- 5 -
CHAPTER 3 INSTALLATION.................................................................................................................................. - 6 -
1. HARDWARE CONNECTION..................................................................................................................................- 6 -
2. SOFTWARE INSTALLATION.................................................................................................................................- 7 -
3. NETWORK CONFIGURATION..............................................................................................................................- 9 -
CHAPTER 4 USING THE WEB UI ........................................................................................................................ - 13 -
1. LIVE VIEW ......................................................................................................................................................- 14 -
2. PLAYBACK ......................................................................................................................................................- 17 -
3. CONFIGURATION PAGE.....................................................................................................................................- 22 -
CHAPTER 5 CONFIGURE THE SETTINGS WITH WEB UI............................................................................- 23 -
1. SUB ITEMS.......................................................................................................................................................- 23 -
2. VIDEO SETUP (AVAI L ABLE F OR ADMINISTRATOR ONLY)..................................................................................- 24 -
3. CAMERA SETUP...............................................................................................................................................- 26 -
4. EVENT SETUP..................................................................................................................................................- 29 -
5. SYSTEM SETUP....................................................................................................................................................35
6. NETWORK SETUP ................................................................................................................................................ 42
7. STORAGE SETUP..................................................................................................................................................48
APPENDIX A SPECIFICATIONS................................................................................................................................50
1. P500....................................................................................................................................................................50
2. P1500..................................................................................................................................................................52
APPENDIX B THE MINI DIN CONNECTOR........................................................................................................... 53
APPENDIX C FAQ.........................................................................................................................................................55
1. HOW CAN I SET FACTORY DEFAULT?....................................................................................................................55
2. HOW TO CHANGE THE TV STANDARD (P1500 ONL Y)...........................................................................................57
3. HOW TO UPGRADE FIRMWARE FOR THE DEVICE? .................................................................................................58
4. WHY ACTIVEX REMAINS IN OLD VERSION AFTER UPGRADING TO NEW VERSION FIRMWARE?..............................60
- 2 -
Chapter 1
Introduction
1. What is PiXORD Dual Streaming Network Camera/Video Server?
The PiXORD 500 (Network Camera, hereinafter called P500) and 1500 (Network Video Server,
hereinafter called P1500) are professional MPEG-4/MJPEG dual streaming surveillance products. Dual
streaming allows seamless remote video monitoring using MPEG-4/MJPEG concurrently with
transmission of high quality MPEG-4 stream to an optional storage. The audio stream can also be
compressed and distributed over Intranet/Internet as the result of capable being recorded. Both P500 and
P1500 have 2 USB 2.0 host ports; with external storage connected the video/audio can be recorded
locally. For power solution, while normal adapter is applied for both devices they also come with the
optional PoE model. The P500/1500 successfully provides the solution of remote monitoring and quality
recording in surveillance.
- 3 -
2. Features
Self-Contained Web Server providing Internet capability for remote access
MPEG-4 ASP / MJPEG dual compression formats
Simultaneous MPEG-4 and MJPEG stream for multiple clients
Supports up to 30/25 FPS at Full D1 resolution
More than 480 TV lines resolution (P500)
Built-in internal microphone (P500)
Event handling trigger by alarm/motion and action to send video clip by Email / FTP
Two USB 2.0 Host ports support external storage and/or wireless USB connection (to be firmware
upgraded)
IP setup by easy IP Installer / DHCP / Static IP / PPPoE
Supports DDNS for dynamic IP application
NTP (network time server) with DST supported which provide accurate unify system time
Hardware watchdog providing robustness system in critical environment
Chapter 2
Physical Images
1. P1500 Video Server
COM/ GPIO LAN Port
Reset hole
USB Ports Power Jack
Audio Output
Video Input
Video Output Audio Input
NTSC/PAL Switch
- 4 -
2. P500 Network Camera
COM/ GPIO LAN Port
Audio Line Out
Reset hole
USB Ports Power Jack
Camera Lens Built-In Microphone
- 5 -
Chapter 3
Installation
1. Hardware connection
Physical connection of P1500 video server
1. Prepare a PC with Ethernet link to the network
2. Connect P1500 device to a network hub/switch with standard pass through (CAT5) cable, or
connect directly to PC with a cross over cable.
3. Connect the video output of a CCD camera using standard 75 Ω coaxial cable terminated with
BNC connector.
4. Connect power jack
- 6 -
5. Ensure the power adapter specification matches the power system (110V or 220V). Connect
the adapter to the outlet.
6. Check both LEDs (Power/Network); ensure they are light on after the steps above.
Follow the same steps as connecting P1500 video server except step 3, to perform the P500
connections.
Physical connection of P500 Camera
2. Software Installation
The following software is necessary for the proper display and use of the P500/1500 from the Web site.
- 7 -
- 8 -
The software will be taken from the Software Package CD.
IP Installer
The IP Installer is used to locate and configure network cameras and video servers on the LAN. This
utility is useful for conveniently configuring the network settings of the device, or for finding a device once
the network settings have been modified.
To install the IP Installer, from the Software Package CD UI, select IP installer, then follow the on screen
instructions.
Component Installer
The ActiveX component is used by our devices for video display and device configuration. Usually, when
you connect to the P500/1500 via IE browser, the ActiveX component will be installed automatically. If the
components can not be installed, install this software from the Software Package CD.
XVID Codec
An MPEG-4 codec is applied for displaying the video stream and playing the recoded AVI files. If the
video stream can’t be displayed or the recorded AVI files can be play on PC, install this software from the
Software Package CD.
VLC
Though not necessary, this can be used for viewing the streaming without a Web browser.
3. Network Configuration
IP Installer is a utility that provides an easier, more efficient way to configure the IP address and network
settings of the devices. It even provides a convenient way to set the network settings for multiple devices
simultaneously using the batch setting function. Moreover, IP Installer can save the network settings for
all devices as a backup and restore them when necessary.
Preparation before IP As signment
1. Always consult your network administrator before assigning an IP address to your server in order to avoid
using a previously assigned IP address.
2. Ensure the P500/1500 is powered on and correctly connected to the network.
3. MAC Address: Each device has a unique Ethernet address (MAC address) shown on the label of the
device as the serial number (S/N) with 12 digits (e.g. 000429-XXXXXX).
- 9 -
4. Although the IP Installer is able to find and configure any P500/1500 on the LAN except those that are
behind a router, it is a good idea to set the host PC to the same subnet. In order to connect to the
Web-based user interface of P500/1500, the host PC must be in the same subnet. For more information
about subnets, please consult your network administrator.
*0004290000B1
Using IP Installer to Assign an IP Address to P500/1500
1. Once IP Installer has been successfully installed on the PC, double click the IP Installer icon on the
desktop, or select it from Start > Programs > IP Installer > IP Installer > Launch IP Installer.
2. Click the menu bar Tool > Search Network Device to search the device in the LAN.
3. From the list, select the device with the MAC Address that corresponds to the P500/1500 that is to be
configured. The MAC Address is identical to the unit’s S/N (Serial Number).
4. Double click the item to open the Property Page for the selected device or click the menu bar View >
Property.
- 10 -
5. After filling in the properties, click [Synchronize] button to complete the configuration settings in the
remote P500/1500 while saving configuration in the PC. If click [OK] button, the configuration is only be
saved in the PC.
Open the Web-based UI of the Selected P500/1500
1. To access the Web-based UI of the selected unit, run the View > Open Web on the menu bar.
2. If the device has been configured correctly, the default Web browser will open to the home page of the
selected device.
3. If you find your browser is opened and automatically connected to the P500/1500 Home Page, it means
you’ve assigned an IP Address to the unit successfully. Now you can close the IP Installer and start to use
your P500/1500.
- 11 -
- 12 -
Verify and Complete the Installation from Your Browser
When browsing the Home Page at the first time with the Microsoft Internet Explorer
TM
, you must temporarily
lower your security settings to perform a one-time-only installation of the ActiveX component onto your
workstation, as described below:
1. From the Tools menu, select [Internet Options]
2. Click the [Security] tab and then click [Custom Level] button to see your current security settings.
3. Set the security level to Low and click [OK].
4. Type the URL or IP address of your P500/1500 into the Address field.
5. A dialog box will pop up asking if the ActiveX control should be installed. Click [Yes] to start the
installation.
6. Once the ActiveX installation is complete, return the security settings to their original value, as noted
above.
Chapter 4
Using the Web UI
Start your Web browser and enter the URL or IP address in the Address field. The Home page of the
P500/1500 is now displayed.
The status of the
video stream
The display of channel information can be
configured in the OSD setting, including
video status, channel number, camera title,
frame rate and transfer speed (bit rate).
Note: Please notice to install the version of XVID codec and recommends V1.1 above, it can be found in the
CD package.
- 13 -
1. Live View
Functions in live view page
The following are the available keys in the Live View mode:
Button Description
Select the display language for web user interface
Check “Actual Size” to display the video stream at the actual resolution
Check “Audio” to enable audio recording.
Click “Rotation” to rotate the selected video on 90 degrees clockwise direction.
Click “Record” to start/stop recording.
Click “PTZ” to show up a panel for the PTZ operation.
- 14 -
Click “Deinterlace” to expend the option of deinterlace On/Off
Users need to set the file path before taking the snapshot. Click on [BMP] or [JPEG]
to take an image with the bmp or jpeg file format respectively.
Set the recording parameters including the recording path, file name, total file
space, maximum file length, enabling/disabling cycle recording and synchronize to
timestamp. Click on “Setting” to apply the change.
Go to the Playback page for search and play back recorded video file
Note: The user that log in with user account* can’t use the Playback function
Go to the Configuration page for setup
Note: The user that log in with user account* won’t have an access to this page
* P500/1500 user setting can be categorized in three groups, the Admin, operator and user. Detail
description can be found in Configuration page > System > User.
- 15 -
P/T/Z Control for Dome Camera
The following are the available keys to control the PTZ dome camera:
Button Description
Select the preset point for quick view or setup
Click on the arrow buttons to move the camera to that direction
Click on the rectangle button to stop the movement
Zoom
Zoom out the video
Zoom in the video
Stop the adjustment
Iris
Open the iris and reduce glare
Open the iris and brighten the picture
Stop the adjustment
Focus
The target will become farther
The target will become nearer
Stop the adjustment
Auto Pan
Activate the auto pan function
Stop the auto pan function
Save Click this button will save the current data as a preset point
- 16 -
2. Playback
To play back the recorded file, click the button in Home page
- 17 -
Button Description
This will be displaying playback status include the speed
of playing, playing mode and name of the controlling user.
Select “Record HDD” or “Backup HDD” to search for the
recorded file. Click [Search] button to open the Search
panel, see Figure 1.
Click this button to expand a setting panel for recording
the playback stream to the client PC, see Figure 3.
Click this button back to the Live View mode
Go to the Configuration page for setup
Note: only 1 user can control play back streaming in a meantime. Other than the first user will be able to see
the playing only (not to control) and who is controlling.
For the first user (must at least have an operator authority) going to start playback:
1. Select the hard disk that will be searched for.
2. Click Search button to open the Date/Time panel for choosing.
3. Select by Date/Time in the calendar. To know the usage of the calendar, just move the cursor on the
button, the tips for the button will appear.
4. After select the Date/Time, click on [Begin Playback] button to playback all recorded video from the
selected time or [Event list] button to choose the recorded video files from events list, see figure 1& 2.
For other clients (even logged in as an administrator)
As one user is controlling the playback, the other clients must wait until the user stops the playback function.
During the waiting time these clients can only view the streaming of playback.
Close this panel
The start and end time of the all video recording
The start time of the recording you can manual input
or click calendar to play
The event type of the recording you can select to play
Status of control playback
You can click this to change play time
You can click this to increase of number or press button
of “Shift” and click this to decrease of number
You can click button of “Begin Playback” to play time or
click “Event List” to play event list
Figure 1
- 18 -
Current page
Tota l page
“Next“” button
Event List
Item
Channel
Event Type
Duration
Event Time
Event Date
Figure 2
Playback Screen
Controller’s View
Other clients’ View
- 19 -
The following are the available keys to control the playback:
Button Description
Rotation: Rotate the playback images.
Record: Record the playback video while viewing.
Click “Deinterlace” to expend the option of deinterlace On/Off
Same operation as in live page. Snapshot the playback video.
Play / Pause / Resume the playback
Back to 1X speed for playback
Stop the playback and exit the Playback function
Fast forward / Rewind the playback. 1X ~ 32X speeds
selectable.
Playback in slow motion. After pause, select the speed from
1X ~ 1/32X.
Show the status of playback.
Click [Search] button to search and play back the recorded video.
See
Remote Record Playback Stream for detail.
Click this button back to the Live View mode
Go to the Configuration page for setup
- 20 -
Remote Record P layback Strea m
The playback stream can also be saved to a client PC while viewing. This is a handy function for that
when a user is far away from P500/1500 but needs an actual copy of recorded video file.
1. Set a path to store the video. Click on [Record setting] button. A setting panel will be expanded and
shown. See below figure.
2. Press on the red button [Record], the playback video will be saving to the path set previously.
3. Besides save playback video, user can also snapshot an image from the video. The operation is
identical to operating in the live page.
- 21 -
3. Configuration page
Click “Config” icon to open the Configure Page.
- Video: Set up the resolution and quality for recording and live view, and the schedule recording
- Camera: Setup video parameters, PTZ settings for cameras
- Event: Setup for event trigger
- System: Setup for system including date/time, user, COM port and commands etc.
- Network: Setup for network
- Storage: Setup for recording storage and schedule.
- Home: Back to the Home Page
The detail descriptions / configurations are in the following chapter.
- 22 -
Chapter 5
Configure the Settings with Web UI
1. Sub items
Video:
Camera:
Event:
System:
Network:
Storage:
- 23 -
2. Video Setup (Available for Administrator only)
Video Setup
Video system: Configuration of video system in NTSC, PAL or Auto for auto detection of connected
camera. This option only applies (presents) to video setup page of P1500 video server.
Total IPS: Decide each “Total IPS” in Day, Night and Weekend of time for this channel, up to 30 for each
time period. When stream2 is enabled, the total IPS can be shared by both streams.
Stream 1 IPS: Set distributed IPS for Stream1 out of 30.
Stream 2 IPS: Set IPS for Stream 2 out of a number the rest IPS after occupied by Stream 1.
- 24 -
- 25 -
Stream 1:
- Resolution: Streaming / Recording resolution can be selected from 352X240 (SIF), 720X240
(Half D1) and 720X480 (Full D1).
- GOP: Define a duration that a GOP (Group of Pictures) will present. Options start from 1/2 to 1,
2, 3 and 4 FPS. The images will be from clearer to less clear accordingly, the required recording
space will be relatively increasing in the choice of smaller number.
- MPEG4 Profile: Selection of SP (Simple Profile) or ASP (Advanced Simple Profile).
- Video Mode: Choose video encoding mode between VBR (Variable Bit Rate) and CBR
(Constant Bit Rate)
- Video Quality: When VBR mode is set, the video quality can be set from 31 levels (1~31, high
~ low). Note: when resolution is set to Full D1, the quality level can only be set from 5 to 31.
- Video Bitrate: When choosing CBR for the video mode, video bitrate can be selected among
64 Kbps, 128 Kbps, 256 Kbps, 512 Kbps, 768 Kbps, 1 Mbps, 1.5 Mbps, 2 Mbps, 3 Mbps and 4
Mbps.
- Event action: Choose Motion (motion detection), Sensor (sensor triggering) or Both (enable
both types) for the event action. The configurations hereafter titled with “Event” will take effects
when any event action is selected; no effects when None is selected.
- Event max IPS: Select the maximum IPS that will be applied when there is an event.
- Event Mode: Choose encoding mode (VBR/CBR) when there is an event.
- Event Quality: Choose image quality when there is an event.
- Event Bitrate: Select the video bitrate when there is an event. The CBR must be selected for
event mode to enable this selection.
Stream 2:
- Dual stream enable: Set the second stream On/Off.
- Stream format: The stream format can be set to “MJPEG” or “MPEG4”.
- MPEG4 Profile: Selection of SP (Simple Profile) or ASP (Advanced Simple Profile).
- Resolution: Streaming resolution can be selected from 352X240 (SIF), 720X240 (Half D1) and
720X480 (Full D1).
- Video Mode: Choose VBR or CBR for stream2 video encoding mode.
- Video Quality: When VBR mode is set the stream2 video quality can be set from 31 levels
(1~31, high ~ low) in MPEG4 format or 100 levels (1~100, low ~ high) in MJPEG. Note: when
resolution is set to Full D1, the quality level can only be set from 5 to 31 in MPEG4 mode, or
from 1 to 90 in MJPEG.
- Video Bitrate: Choose Stream2 video bitrate when video mode is CBR.
- Apply: Confirm the settings.
3. Camera Setup
General Setup
- Brightness / Contrast / Saturation / Hue: Adjust the values from -100 to +100.
- BLC: Enable/disable BLC (Back Light Compensation) function.
- AES: Enable/disable AES (Auto Electronic shutter) function.
Note: The BLC and AES functions will not appear in this page when connecting to a video server,P1500 (show
only in camera P500 setting page)
- Camera Title: Input the camera title to shown on the screen.
- Stream time: on/off the time displaying on the live video.
- Stream title: on/off the title displaying on the live video.
- Stream text: when stream title is set off, this filed can be input some texts for displaying on the video.
- Load Default: Restore to the default settings.
- Apply: Confirm the settings.
- 26 -
PTZ Setup
- PTZ Setting:
Remove: No dome camera is connected to this channel.
Add: A dome camera is connected to this channel.
- PTZ Protocol: Various protocols can be selected, including PELCO P, PELCO D, LI-LIN and
Dynacolor.
- PTZ ID: The ID number must match the ID address set by the dome camera.
- Speed: Select the control speed from 1 ~ 10.
- Apply: Confirm the settings.
- 27 -
OSD Setup
- OSD Display: Check the check box to display the following messages on the video of each channel.
Note: The settings work with this client PC only; it won’t affect/change the settings of this device.
- Status Display: Display the video status (Live or Playback video).
- Channel Display: Display the channel number.
- Title Display: Display the camera title.
- Frame rate Display: Display the frame rate and bit rate.
- Apply: Confirm the settings.
Channel Display
Title Display
Status Display
Frame rate Display
- 28 -
4. Event Setup
General Setup
- Event Icon: M / S displaying on the screen indicates respectively motion detection or GPIN is
triggered. Set this function “On” to enable displaying the two icons.
- Event Duration: Set the duration time for recording after the event goes away. Available selections
are 5, 10, 15, 20, 25 and 30 seconds.
- Pre Alarm: When an event is triggered, a video clip will be sent with Email or saved to FTP site. You
can adjust this option to determine the beginning time of video clip before the event is triggered. The
unit is in second.
- Apply: Confirm the settings.
- 29 -
Triggers Config
Motion trigger: Define parameters for actions responding to detected motion.
- Motion Detect: Set the Motion Detect feature for each channel to “ON” or “OFF”.
- Alarm Out: Enable a relay output that will respond to a detected motion.
- Pass Alarm: Adjust this option to determine the end time of a video clip after the triggered
event. The value is counted in second.
- Email Notice: Enable or disable the Email notice when motion detection is triggered.
- Email Attachment: Set whether attach the video clip with the Email notice when motion
detection is triggered.
- FTP Storage: Enable or disable whether send the video clip to FTP site when motion detection
is triggered.
- CGI Alert: Enable or disable to send CGI alert when motion detection is triggered.
- Period Time / Week: Select the period that the motion detection should be activated. Day、
night、 weekday、 weekend or all the time.
- Sensitivity: Set the sensitivity of motion detection.
- 30 -
GPIN trigger: Apply the sensor relays as trigger. Define the actions/parameters responding to an event
- Alarm in: enable the GPINs as a sensor for the event triggering.
- Alarm Out: Enable a relay output that will respond to a triggered sensor.
- Normal state: set the relays’ initial status.
- Pass alarm: as described in motion config.
- Email notice: send email responding to a sensed event
- Email attachment: send email with attached video file.
- FTP storage: send video file to FTP server responding to a sensed event.
- CGI alert: enable the CGI alert responding to a sensed event.
- Period time / week: select the period of time/day in a week that the sensor will be activated.
- 31 -
Video loss trigger: Set actions responding to an event which the video is missing. For instance, line has
been cut or camera has been crashed.
- Video loss detect: on/off this function.
- Email notice: as described in previous two items.
- CGI alert: as described in previous two items.
- 32 -
Motion Area Setup
Move mouse cursor to point the area, left-click mouse to set the area for motion detection; left-click the
selected area again will clear the area.
- Select All: Clear all areas for motion detection.
- Clear All: Select all areas for motion detection.
- Set: Confirm the settings.
- 33 -
GPIO Setup
- GPIO Input Status: Displays the current GPIO input status
- Relay Settings: Displays the output relays’ status. The relays can be forced open or closed.
- 34 -
5. System Setup
General Setup
- Unit Name: Assign a name for the device.
- Model: The model name of the device.
- Hardware Version: The version of the hardware.
- Software Version: The version of the software.
- Firmware Version: The version of the firmware.
- Apply: Confirm the settings.
35
Date/Time Setup
Set the year, date and time for the device.
- DST Enable: If your region use daylight saving time, set the item to “ON”.
- Bias: Set the amount of time to move forward from the standard time for daylight saving time.
- Start: Set the beginning date/time of the daylight saving.
- End: Set the ending date/time of the daylight saving.
- NTP Enable: Set to “ON” if you wish to connect to a NTP server, this will synchronize the time with
the time server via network.
- GMT: Set the time zone.
- NTP Server: Input the IP address of the NTP server.
- Set Manually: Set the time manually. You can select the time from the calendar.
- Apply: Confirm the settings.
36
User Password Setup (Available for Administrator only)
- Enable Authentication: Select “YES” to enable the password authentication.
- User name / Password: Up to 15 accounts can be added for accessing this device. The account
name and password can be flexible (but restricted in 8 characters long of any combination of 0-9, a-z
or A-Z).
- Group: A user should also be configured into a group (Administrator, Operator, User) for different
level of authority, in addition, the rights on access to the device (the capabilities of viewing live video,
controlling PTZ cameras or none/both of them) if it is not set to the administrator group.
- Apply: Confirm the settings.
37
COM Port Setup
- COM Status: Set COM port for PTZ, RS-232 or RS-485.
- PTZ ID: The number must match the ID address set by the dome camera.
- Baud Rate: Set the value if necessary.
- Data Bit: Set the value if necessary.
- Stop Bit: Set the value if necessary.
- Parity: Set the value if necessary.
- Flow Control: Set the value if necessary.
- PTZ Protocol / Status: Display the PTZ protocol and the status of the connected dome camera.
- Apply: Confirm the settings.
38
System Commands (Available for Administrator only)
- Factory Default: Restore the settings to the factory defaults.
- Reboot: Restart the device.
39
System Information
Display the information of this device. Information includes video port, resolution video type, bit rate, PTZ
model/status, motion status, sensor status and ActiveX version.
40
System Audio
System audio enable and adjustment: Mute check box for silence, Volume for the sound volume
adjustment.
41
6. Network Setup
General Setup
- Ethernet Mode: If using static IP, set to “Static” and then setup the following settings. If there is a DHCP
server on the network, set to “DHCP”, the device will get the following settings from the server
automatically.
- IP Address: Set the IP address of the device.
- Subnet Mask: Set the subnet mask.
- Gateway: Set the IP address of the gateway on the network.
- MAC Address: Shows the MAC address of the device.
- HTTPS: on/off the HTTPS option.
- HTTP Port: Change the port if necessary.
- RTSP Port: Change the port if necessary. Default port is recommended.
- RTSP Start: Change the port if necessary. Default port is recommended.
- RTSP End: Change the port if necessary. Default port is recommended.
- DNS1 / DNS2: Set the IP address of the DNS server.
- Apply: Confirm the settings.
42
DDNS Setup
Dynamic DNS Settings 1:
- DDNS Enable: DDNS allows the dynamic IP address to be registered so others can connect to it by a domain
name. If you wish to use DDNS service and set to “ON”.
- Host Name: Assign a host name for the device, this name will be the domain name.
- Port: Change the port if necessary.
- DDNS Server: Input the domain name of the DDNS server.
- Router Incoming Port: If the device is connected to a router, change the port to match the Port Forwarding setting
in the router.
- Update Time: Set the interval time to detect the IP address and update to the DDNS server. The time setting must
be in the range 600~86400 seconds.
- Response: After confirm the settings; a message will appear for check the DDNS status.
- Apply: Confirm the settings.
43
Dynamic DNS Settings 2:
- DDNS Enable: As in settings 1 mentioned.
- Host Name: As in settings 1 mentioned.
- Account ID: For the server needs an account to log in, the field here is then for the account identification.
- Password: password for the account to log in.
- Update Time: As in settings 1 mentioned.
- Response: As in settings 1 mentioned.
- Apply: Confirm the settings.
44
Email Setup
- Email via SMTP: Set to “ON” if use a SMTP server to send the Email.
- SMTP Server: SMTP server IP address.
- SMTP Port: Change the port if necessary. Default is recommended.
- Authorization: Set to “ON” if the Email service needs account and password.
- SMTP Account / Password: If the SMTP server has enabled authentication function. You have to fill up the
Account and Password to pass through the authentication.
- Email to Address: The Email address to receive the Email.
- Email from Address: The Email address that send the Email.
- Apply: Confirm the settings.
45
FTP Setup
- FTP enable: Set to “ON” if use a FTP server to receive the event notification.
- Server IP: Enter the IP address of the FTP server.
- User Name / Password: The account name and password to login the FTP server.
- Storage Path: Path of the FTP site to put the file.
- Apply: Confirm the settings.
46
PPPoE Setup
- PPPoE enable: Enable/disable PPPoE function.
- User name / Password: Account authentication; enter user name and password for the PPPoE
account.
- Apply: Confirm the settings.
47
7. Storage Setup
Storage USB Setup
Display the information and status of the storage devices that connected to P500/1500.
- Active: represents the disk will act as a “Record” or “Backup”, or “Off” as taking no action.
- Action: shows the disk’s mounting status, Add/Remove.
- Priority: Set the priority in number if there is more than one disk. The number is counted from 0 to 8;
0 indicates the top priority while 8 is the lowest. Disk with higher priority will always be taken to act
unless it is full.
- Type: the disk will be formatted with EXT file system if “Record” is taken active, while EXT or FAT file
system can be applied for “Backup” activity
- Format: Format the disk with these conditions.
48
Storage Record Setup
- Start Schedule Record: When set to “ON”, the recording will depend on the set day and night time,
or weekend time.
- Day Time Start: Set the beginning time of the day.
- Night Time Start: Set the beginning time of the night.
- Weekend Schedule: When set to “ON”, the weekend schedule will be enabled.
- Weekend Start Week / Time: Set the beginning day and time of the weekend.
- Weekend End Week / Time: Set the ending day and time of the weekend.
- Overwrite Recording: When set to “ON”, if the record HDD is full, the recording will overwrite the
earliest recorded file in the HDD.
- Audio Recording: When set to “ON”, both video and audio will be recorded.
- Apply: Confirm the settings.
- “Record Hard Disk setting error!” This message shows when there is no storage to be set active.
49
50
Appendix A
Specifications
1. P500
P-500
System Embedded Linux, 32-Bit RISC Processor, 8MB Flash ROM, 64MB SDRAM
Video Compression MPEG-4 ASP / MJPEG, Dual streaming
Full D1: NTSC = 720 x 480; PAL = 720 x 576
Half D1: NTSC = 720 x 240; PAL = 720 x 288
Video Resolution
CIF: NTSC = 352 x 240; PAL = 352 x 288
Frame Rate Up to 30(NTSC) / 25(PAL)
Image Device 1/3” Sony SuperHAD CCD
Lens Type CS mount, Fixed iris, Focal Length 6.0mm, F1.6; With DC-iris jack to support auto iris lens
Horizontal Resolution More than 480 TV Lines
Minimum Illumination 0.5 Lux at F2.0
White Balance Auto
Backlight Compensation ON / OFF selectable
Auto Electronic Shutter ON / OFF selectable
Trigger GPIN, Motion detection,
Event System
Action GPOUT, FTP, Email and alert message
Local Storage Support schedule / event recording via external USB2.0 port
10/100 Base-T Ethernet
Network Interface
Optional IEEE 802.11b/g wireless LAN via USB (to be upgraded)
Protocols TCP(UDP)/IP, HTTP, FTP, Telnet, SMTP, DHCP, NTP, DDNS, RTSP, RTP/TCP(UDP)
Audio Capability 1x Built-in Microphone, 1x 2.5mm Line out jack (to be firmware upgraded)
DC switching power adapter, output: DC 12V/1.5A
Power Supply
Optional built-in PoE IEEE 802.3af
Operation Temperature 5oC ~ 45oC
Operation Humidity 20% ~ 80% RHG
Dimension (L x W x H) 135mm x 85mm x 40mm
Net Weight 600 g (approximately)
51
2 x USB 2.0 Host ports for external storage or USB wireless LAN (to be firmware upgraded)
1 x Mini-DIN for RS-485 / Photo-coupled GPIN / Relay GPOUT / Video out
1 x Reset hole to restore factory defaults
1 x RJ-45 Ethernet connector with 2 LEDs (power/status)
I/O Connectors
1 x DC In connector
Package Contents
1 x CD (manual and software), 1 x Ethernet cable, 1 x Mini Din to Terminal block extend cable,
1x Stand for mount, 1 x ACDC Power Adapter (Not included with PoE model)
52
2. P1500
P-1500
System Embedded Linux, 32-Bit RISC Processor, 8MB Flash ROM, 64MB SDRAM
Video Compression MPEG-4 ASP / MJPEG, Dual streaming
Full D1: NTSC = 720 x 480; PAL = 720 x 576
Half D1: NTSC = 720 x 240; PAL = 720 x 288
Video Resolution
CIF: NTSC = 352 x 240; PAL = 352 x 288
Frame Rate Up to 30(NTSC) / 25(PAL)
Analog Video Input / Output 2 x BNC (1 video input, 1 x video out)
Pan / Tilt / Zoom Control Yes, supports Peloco-P, Pelco-D, Lilin, Dynacolor protocols
Trigger GPIN, Motion detection,
Event System
Action GPOUT, FTP, Email and alert message
Local Storage Support schedule / event recording via external USB2.0 port
10/100 Base-T Ethernet
Network Interface
Optional IEEE 802.11b/g wireless LAN via USB (to be upgraded)
Protocols TCP(UDP)/IP, HTTP, FTP, Telnet, SMTP, DHCP, NTP, DDNS, RTSP, RTP/TCP(UDP)
Audio Capability 1x 3.5mm Line in jack, 1x 3.5mm Line out jack (to be firmware upgraded)
DC switching power adapter, output: DC 12V/1.5A
Power Supply
Optional built-in PoE IEEE 802.3af
Operation Temperature 5oC ~ 45oC
Operation Humidity 20% ~ 80% RHG
Dimension (L x W x H) 119mm x 142mm x 46mm
Net Weight 510 g (approximately)
2 x BNC connectors for analog video in / out
2 x Line jacks (Audio In/Out)
2 x USB 2.0 Host ports for external storage or USB wireless LAN (to be firmware upgraded)
1 x Mini-DIN for RS-485 / Photo-coupled GPIN / Relay GPOUT / Video out
1 x Reset hole to restore factory defaults
I/O Connectors
1 x RJ-45 Ethernet connector with 2 LEDs (power/status)
Package Contents
1 x CD (manual and software), 1 x Ethernet cable, 1 x Mini Din to Terminal block extend cable,
1 x ACDC Power Adapter (Not included with PoE model)
Appendix B
The Mini Din Connector
The mini-din connector provides control signal input and output, which including GPIO input, GPIO output
as Relay connection and one RS-485 port multiplex with COM port. It also provides connection of PTZ
device and external console to control the device.
COM / GPIO MINI-DIN
PIN FUNCTION
1 GPIN
2 RXD (Receive Data)
3 TXD (Transmit Data)
4 RS-485A
5 GND (System Ground)
6 GPOUT- Relay NO
7 GPOUT- Relay COM
8 RS-485B
9 Video Out
GPIN: Input high when opening the connection; input low when sinking more than 10mA or
shorting to pin 5 (GND).
RXD (COM Port Receive Data)
TXD (COM Port Transmit Data)
RS485A/RS485B: To connect with external PTZ devices, please contact your dealer/distributor
to get the information of the supported PTZ models.
GND (System Ground): System Ground is also connected to chassis as frame ground.
GPOUT-Relay NO/COM: When there is a triggered event, this can be a response that pin 6 is
short to pin 7 and enables an alarm device.
Video Out: directly output the analog video signal.
53
Mini-Din to Terminal block extended cable
This cable within the product package is provided for an easier application/connection. See below figure.
54
Appendix C
FAQ
1. How can I set factory default?
ANS:
1. Unplug the power jack to turn off the power of P500/1500.
2. Insert a pin into the reset hole as circled with red in the below figures. Sense a button and keep
it pressed until instructed to release.
3. Plug in the power jack to turn on P500/1500, in about 20 seconds the network LED circled in
blue will be flashing
4. Release the button (remove the pin from the reset hole).
5. The P500/1500 should now be back to factory default. Have an access to the device by
changing to the attempt IP address from the default 192.168.0.200.
P500
P1500
55
Note:
1. When P500/1500 can be scanned by IPInstaller with this IP “192.168.0.200” after factory
setting, it means the reset process is successful.
2. There will be totally 9 On-Off flashings, within this period the reset progress will be launched. If
the inserted pin is removed before or after flashings, the system wouldn’t take any effect; the
reset will be unsuccessful. Redo from step 1 for another chance.
3. Do not remove power any time in the reset process, the flash memory inside the device can be
damaged otherwise.
56
2. How to change the TV standard (P1500 only)
ANS:
1. Unplug the power jack to turn off P1500, and then set the DIP Switch in the front panel:
- NTSC: set the switch 1 to the up position.
- PAL: set the switch 1 to the down position.
2. Plug in the power jack to turn on P1500, the video output of P1500 will meet the TV standard.
57
3. How to upgrade firmware for the device?
ANS:
Download the newest software and unzip it into your local driver, for example "C:\temp". Then, confirm
the "flash.bin" (or flash_all.bin) file exists in this directory.
Restart the device by clicking on the <Reboot> button on Configuration page -> System -> Commands.
Caution: You must reboot the device before doing the following procedures; otherwise, some
occasional internal conflicts ma
y
endanger the Flash devices.
Start the FTP session and log in to the P500/1500.
For example, in our case for Windows XP:
Enter DOS by "
Start > All Programs > Command Prompt."
Change to the directory where the latest flash.bin exists.
Start ftp session by enter “ftp <Device IP Address>
Enter "root" for USERNAME, "pass" for PASSWORD as default administrator; you will have to use your
administrator's USERNAME and PASSWORD to login if you ever added a user with administrator
authority.
Set FTP to binary mode using the command "bin".
In FTP session window, enter "bin"
Upload the software into the device by FTP "put" command.
In FTP session window, enter "put flash.bin"
In FTP session window, enter "bye" to quit FTP session.
FTP session may freeze for around 1~2 minute to transfer and automatically upgrade the software.
Use “ping” to check whether the device is accessible. If you get replies after pinging, you then should
be able to access the device via Web interface. The figure of Command Prompt below shows an
example of the whole operation.
58
Note: Flash products can become damaged if the updating operation is not performed correctly. So please
follow u
p
above procedures carefully.
59
4. Why ActiveX remains in old version after upgrading to new version
firmware?
ANS:
Launch an IE browser and click on “Tools” -> “Internet Options”. The Internet Options window then
shows up.
60
In Temporary Internet files, click on Delete Files.
Press “OK” to confirm deletion.
61
Re-open IE browser and access to the device. You will this time be prompt to install newer version of
ActiveX control. After installation, you should see the new version installed.
62
Loading...