Pixel Magic Crystalio II VPS3300, Crystalio II VPS3800 Owner's Manual
Owner’s Guide
For Models
VPS3300 & VPS3800
2
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not expose this appliance to dripping or splashing water and no object filled with liquids (such as
vases) should be placed on this appliance.
10. Do not interfere with the safety aspects of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
11. Protect the power cord from being walked on or pinched particularly at plugs and the point where they exit
from the apparatus.
12. Only use attachments/accessories specified by the manufacturer.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as if the power-supply cord or plug has been damaged, liquid has been spilled,
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
SAFETY INFORMATION
3
ADDITIONAL SAFETY INSTRUCTIONS
• To ensure maximum performance, please read this manual carefully. Keep it in a safe place for future reference
• Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust,
moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not
expose the unit to rain or water
• Never remove the unit cover. Contact your dealer if an object falls inside the unit
• Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug
and the wires connected to other equipment. Never pull on the wires themselves
• The openings on the unit cover assure proper ventilation of the unit. If these openings are obstructed, the
temperature inside the unit will rise rapidly. Therefore, avoid placing objects against these openings, and install
the unit in a well-ventilated area to prevent fire and damage
• Be sure to allow a space of at least 30 cm behind, 20 cm on both sides and 10 cm above the top panel of the
unit to prevent fire and damage
• Digital signals generated by this unit may interfere with other equipment such as tuners, receivers or TVs.
Move this unit further away from such equipment if interference is observed
• Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth
• Be sure to read Section
8: Troubleshooting regarding common operating errors before concluding that the
unit is faulty
• When not planning to use this unit for long periods of time, disconnect the AC power plug from the wall outlet
• To prevent lightning damage, disconnect the AC power plug when there is an electrical storm
• Grounding or polarization - Precautions should be taken so that the grounding or polarization of an appliance
is not defeated
• This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this
unit itself is turned off. This state is called the standby mode. In this mode, this unit is designed to consume a
small amount of power
4
Thank you very much for purchasing Crystalio II, the World’s most advanced video processor! This unit will
bring you a breathtaking visual experience by revealing the full potential of your display devices.
After unpacking Crystalio II, please save all packing materials; they may be useful as a safe way to transport
your system. If any part of your system is missing or appears damaged, contact your dealer immediately.
Before you start, please check that you have all of the following contents with you:
1. Crystalio II VPS3300/VPS3800 Video Processor
2. Backlit Crystalio II Remote Control
3. Mains power lead
4. Crystalio II Owner’s Guide
5. USB Firmware upgrade thumb disk
6. Rack mounting brackets
If everything is ready, you may now:
1. Connect your Crystalio II to your AV devices with reference to Section 3: Hardware Installation.
2. Configure Crystalio II with reference to Section 4: Basic Setup and Section 5: Crystalio II
Configuration.
3. Register your Crystalio II to enjoy official warranty, technical support, and software updates
from Pixel Magic Systems Ltd.
4. Upgrade your Crystalio II with the USB Firmware upgrade thumb disk as provided. Also check the
official Crystalio II website (http://www.crystalio.com) regularly to download the latest firmware.
Enjoy!
Caution: Make sure you read and follow the instructions of the Crystalio II User Guide to connect the
Crystalio II to your AV system.
PRODUCT REGISTRATION
To enjoy the 12-month warranty for your Crystalio II, you must register online at:
http://www.crystalio.com/support.html
This will only take a couple of minutes. You will need your serial number so please make a note of it prior to
registering your Crystalio II.
Once registered, you will be entitled to view technical information, online product support and, of course
software updates for your Crystalio II.
WELCOME
5
Safety Information 2
Important Safety Instructions 2
Additional Safety Instructions 3
Welcome 4
1. About Crystalio II 8
1.1 Why do I need Crystalio II? 8
1.2 Video Processing History 8
1.3 Video Processing Technology Primer 9
Gennum VXPTMTechnologies 9
Faroudja Technologies 10
2. Familiarizing yourself with Crystalio II 11
2.1 Crystalio II Front Panel 11
2.2 Crystalio II Rear Panel 13
2.3 Remote Control 15
2.3.1 Main Crystalio II remote control 15
3. Hardware Installation 18
3.1 Compatible Equipment 18
3.2 Mains 18
3.3 Video Inputs 18
3.4 Video Outputs 19
4. Basic Setup 20
4.1 Configure Your Video Source 20
4.2 Switch On Crystalio II 20
4.3 Select Input Video Source 20
4.4 Select Primary Output Port 20
4.5 Set Output Format/Resolution 21
4.6 Basic Setup Tips for Digital Displays/Projectors 21
4.6.1 Pixel Perfect 21
4.6.2 Output 50Hz or 60Hz automatically 23
4.6.3 Basic Calibrations 23
4.6.3.1 Display video level and color calibration 23
4.6.3.2 Source video level and color calibration 24
4.6.3.3 Calibrating color to compensate for display source inaccurracies 25
4.6.4 Digital projector with anamorphic lens 26
4.6.5 Tips for avoiding burn-in on Plasma Displays 27
4.7 Basic Setup Tips for CRT Projectors 27
4.7.1 Sweet Spot Timings 28
4.7.2 48Hz/72Hz Cadence Lock 28
4.7.3 Basic Calibration 28
TABLE OF CONTENTS
6
5. Crystalio II Configuration 29
Tips for using this section 29
5.1 INPUT Sub-Menu 29
5.1.1 Input Select 29
5.1.2 Input Port Configuration 30
5.1.3 Hide Input Source 31
5.1.4 Input Profile 31
5.2 IMAGE Sub-Menu 32
5.2.1 Video Settings 32
5.2.2 Color Temperature 32
5.2.3 Gamma Correction 33
5.2.4 Aspect Ratio 34
5.2.5 Overscan 35
5.2.6 Position 35
5.2.7 Crop 36
5.2.8 Deinterlace 37
5.2.9 Noise Reducer 38
5.2.10 DCDi 38
5.2.11 Video Profile 38
5.3 OUTPUT Sub-Menu 39
5.3.1 Output Select 40
5.3.2 Output Port Configuration 40
5.3.3 Output Resolution 41
5.3.4 Screen Shape 42
5.3.5 Screen Masking (Blanking) 43
5.3.6 Output Gamma Correction 44
5.3.7 Output Profile 44
5.4 AUDIO Sub-Menu 45
5.4.1 Audio Input Select 45
5.4.2 Input Port Configuration 46
5.4.3 Audio Delay 46
5.4.4 Output Port Configuration 47
5.5 SYSTEM Sub-Menu 47
5.5.1 OSD Options 48
5.5.2 Front Panel 48
5.5.3 Video Test Patterns 49
5.5.4 Passthru 49
5.6 PIcture in Picture/Picture by Picture 49
5.6.1 Advanced Option 52
5.6.2 Import/Export Settings 52
5.6.3 Factory Settings Reset 53
5.6.4 Firmware Upgrade 53
7
6. Front panel configuration 54
Front panel LCD menu tree 55
6.1 Controls unique to the Front Panel 56
6.1.1 System Info 56
6.1.2 Network (VPS3800 only) 56
6.1.3 OSD Control 56
6.1.4 Front Panel 56
6.1.5 Power Up Action 56
7. Advanced OSD options 57
7.1 Digital Input Configuration 57
7.1.1 SDI Input Configuration 57
7.1.2 HDMI Input Configuration 58
7.2 DynamicVP
TM
58
7.3 Advanced Gamma Correction 60
7.3.1 User Defined Gamma Curve 60
7.3.2 R/G/B Individual Gamma Curve 61
7.4 Non-Linear Stretch (NLS) Configuration 61
7.5 Y/C Delay 62
7.6 Noise Reducer 62
7.7 Smooth Scaling 63
7.8 Video Filters 63
7.9 Faroudja DCDi Processor Chip Advanced Options 64
7.9.1 True Life 64
7.9.2 Film Bias 65
7.9.3 Film Detect 66
7.10 Advanced Output Port Configuration 66
7.10.1 Voltage Pump 66
7.10.2 HDMI Output Port Configuration 67
7.10.3 Force DVI 67
7.10.4 Output Sync Polarity/Sync Type 68
7.10.5 Output Port Configuration when in Passthru Mode 69
7.10.6 Output Sync Polarity/Sync Type when in Passthru Mode 70
7.11 Gamma Correction 71
7.12 Color 72
7.13 Output Master Levels 72
7.14 Audio Delay Profile 73
7.15 Secondary Passthru 73
7.16 Macros 76
8. Troubleshooting 78
9. Support & warranty information 80
8
With the huge success of Crystalio in past years, Pixel Magic Systems Ltd. is now proud to introduce an
absolute must for any videophile passionate about their hi-performance home entertainment system: Crystalio II.
It has been designed to deliver the most natural and artifact-free images with smooth motion, true colors and
stunning detail that you have ever experienced.
1.1 WHY DO I NEED CRYSTALIO II?
Crystalio II is the perfect companion for any commercial or home theater application. This is made possible by
the use of Gennum’s Visual Excellence Processing (VXP) image processor which offers revolutionary
improvements over today’s existing solutions by integrating next-generation broadcast-quality algorithms.
You may wonder why you need a separate video processor, if you can simply purchase a projector or a DVD
player with some scaling capability built in. The reasons are performance and flexibility. Crystalio II allows you
to have sophisticated control over every aspect of video processing, so that you can control the performance
of the entire video system to a far greater extent. Crystalio II also gives you the flexibility to enjoy this feature
from basic component video sources right through to pure digital HD SDI and HDMI video.
HD SDI (High Definition Serial Digital Interface) is a specialist video distribution standard for uncompressed
high definition video transmission in the broadcast industry at maximum quality over long distance by co-axial
or fiber optic cable.
High Definition Multimedia Interface (HDMI), on the other hand, is the first and only digital interface to combine
uncompressed high definition video, multi-channel audio and intelligent format and command data in a single
digital interface. You can dramatically simplify home theater system installation by using a single cable for audio
and video and eliminate the cable quagmire typically associated with home theater system components. Most
importantly, HDMI offers significant advantages over analog A/V connections, including the ability to transmit
uncompressed digital video and audio content.
In a nutshell, Crystalio II is able to maximize the performance of any video source, from traditional SVHS
recordings and video games consoles to DVD players, high definition TV broadcast and future high definition
Blu-Ray or HD-DVD players.
The following will describe in-depth the evolution of video processing that has led to the innovation of Crystalio II.
Alternatively you may skip these paragraphs and go directly to Section 1.3 for an overview of the most cuttingedge technologies that Crystalio II has embodied.
1.2 VIDEO PROCESSING HISTORY
So many home theater viewers find that their new projector, plasma or LCD does not provide the expected
increase in image quality and may even appear noisier or less clear than their old standard definition system
or CRT set.
Few people realize when they purchase their first high definition TV set that the majority of TV programming is
still delivered in standard definition. Even true high definition TV transmissions, Blu-Ray and HD-DVD sources
are often still interlaced or have significant noise, or may contain artifacts due to the original recording medium.
To make matters worse, in order to fill a high resolution high definition TV screen the standard definition image
has to be enlarged, unfortunately enlarging all the flaws in the original image too. The video processing built
into most home theater displays and progressive-scan DVD players has limited processing ability, runs basic
algorithms and is unable to properly deal with these flaws.
1. ABOUT CRYSTALIO II
9
1.3 VIDEO PROCESSING TECHNOLOGY PRIMER
Crystalio II gets to the very heart of this problem by a combination of expert video engineering design from Pixel
Magic together with the awesome power of the Gennum Visual Excellence Processing (VXP) image processor.
Crystalio II is the first video processor on the market to use the latest Gennum VXP processor so, if you want to
enjoy the benefit of the new benchmarks for video realism and processing flexibility, Crystalio II is your video
processor of choice.
Listed below are some of the state-of-the-art video processing technologies featured in Crystalio II:
GENNUM VXP™ TECHNOLOGIES:
RealityExpansion™
Traditional banding artifacts are eliminated and images appear smooth and natural by adopting a full 10-bit
video processing architecture to deliver eye-catching and realistic imagery.
FineEdge™
FineEdge™ advanced directional interpolation algorithm eliminates jaggy artifacts found in traditional
de-interlacing solutions. FineEdge™ processing maintains overall image sharpness and detail and is applied
to both SDTV and HDTV sources for optimal image quality.
TruMotionHD™
TruMotionHD™ de-interlacing algorithm is unique in its ability to perform pixe-based motion adaptive
de-interlacing with automatic 3:2 and 2:2 pull-down on both HDTV and SDTV formats. TruMotionHD™
de-interlacing technology supports fully adaptive 1080i > 1080p de-interlacing to ensure optimal image
quality in demanding applications.
FidelityEngine™
FidelityEngine™ enhances the image by removing unwanted noise and improving detail for uncompromised
image quality. Unlike traditional processing algorithms, FidelityEngine™ processing can be applied to both
SDTV and HDTV sources!
Intelligent Scaling Algorithms
Intelligent scaling algorithms can take content intended for one resolution and scale it up or down to match the
desired resolution. The image processors use long and high-resolution poly-phase filters to ensure all of the
HDTV bandwidth is passed to the output. The process is performed in full broadcast-quality 10-bit resolution
with programmable scaling coefficients. As a result, standard definition signals can be seamlessly converted
and displayed on high definition displays. Similarly, high definition video content can be scaled down for display
on common standard definition devices.
Aspect Ratio Conversion
Ideal for flat panel displays and other widescreen appliances that often require conversion between 4:3 and
16:9 aspect ratios. The dynamic resizing parameters allow users to choose between letterbox and pillarbox
formats as well as custom zoom, stretch and shrink modes.
High Resolution Support
Crystalio II can de-interlace HDTV formats to 10-bit 1080p60 for advanced video realism. The high temporal and
spatial bandwidth provided by this format allow for stunning results when down-converting to popular display
formats such as WXGA.
10
FAROUDJA TECHNOLOGIES:
DCDi
®
DCDi® eliminates the jaggedness that conventional up-converters cause to diagonal edges in video.
DCDi®’s unique algorithm identifies all the moving edges in a scene and adjusts the angle of interpolation
at each pixel so that the interpolation always follows the edge instead of crossing it, eliminating staircasing
or jagged edge artifacts.
TrueLife®Enhancement
TrueLife® Enhancement identifies patterns of transition which contain important detail in an image such as skin
texture, freckles or hair. These areas of transition are deliberately enhanced to render the details more visible
and more lifelike. At the same time, the technology enhances large edges to create greater depth of perception
without introducing visible artifacts or distortion.
Cross Color Suppression
Cross Color Suppression uses motion detection to selectively perform the filtering of cross color artifacts like
flickering, flashing colors or rainbow patterns in an intelligent manner, identifying where there is no motion in
the image and using the existing frame memory for the chroma information.
Motion Adaptive Noise Reduction
Motion Adaptive processing reduces noise in an image without causing the smearing of moving objects which
results from temporal filtering (3-D) if not accurately performed.
11
2.1 CRYSTALIO II FRONT PANEL
POWER button
Press once to switch on; press once again to switch to standby.
The status is shown by the power indicator LED.
Caution: When Crystalio II is switched off, please wait for at least 10 seconds before
switching it on again.
POWER indicator LED
Green - Crystalio II is running
Red - Crystalio II is in standby mode
Caution: Never unplug the power plug when Crystalio II is running.
INPUT button
Press to cycle through the Crystalio II video input sources.
Input sources support HDMI; SDI; Component; RGBHV; S-Video; RGBs etc. Please refer to Section 5.1.1:
Input Select for details.
OUTPUT button
Press to cycle through the Crystalio II output ports:
HDMI 1; HDMI 2; Analog. See Section 5.3.1 to 5.3.3 for more information.
Navigation buttons
OK (setup) button
BACK button
2. FAMILIARIZING YOURSELF WITH CRYSTALIO II
1
2
3
4
5
6
7
12
FILM & 2:2 PULLDOWN indicator LEDs
PASSTHRU indicator LED
LCD Display
The LCD display has 2 distinct modes see Section 6 for further details:
Status Display
By default, the LCD displays the current status of Crystalio II,
which includes the following information:
• Input source format
‘(HDCP)’ is shown if signal is HDCP encrypted
• Image aspect ratio
• Overscan
• Gamma type
• Primary output port
• Output resolution
• Deinterlacing mode
Setup Display
When you are setting up Crystalio II, the LCD display shows the setup menu. Typical operation includes:
• To enter menu set up mode, press [OK]
• To highlight the previous or next item, press [UP] or [DOWN]
• To increase or decrease value, press [LEFT] or [RIGHT]
• To select an item or confirm setting, press [OK]
• To exit and go up one level of the menu, press [BACK]
Infra Red (IR) input sensor
Film 2:2 Pulldown Mode
OFF OFF Video (Motion Adaptive Deinterlacing)
ON OFF Film (3:2 Pulldown)
ON ON Film (2:2 Pulldown)
OFF ON Not applicable
8
9
10
11
13
2.2 CRYSTALIO II REAR PANEL
POWER
Power Supply Cable Entry
Use the cable supplied with your Crystalio II.
VIDEO INPUT TERMINALS
These allow you to connect your video sources to
Crystalio II. Please refer to Section 3.3 for
details.
Digital
HDMI 1; HDMI 2; HDMI 3; HDMI 4 (all HDCP and embedded digital audio)
Supported input resolutions:
480i, 576i, 480p, 576p, 720p, 1080i, 1080p,
640x480, 848x480, 852x480, 854x480, 856x480, 1024x576,
800x600, 1280x720, 1024x768, 1280x768, 1360x768, 1366x768, 1368x768,
1400x788, 1280x1024, 1400x1050, 1600x1200, 1920x1080
HD-SDI/SD-SDI 1; HD-SDI/SD-SDI 2
VPS3800 Pro supports all HD-SDI formats; 480i, 576i, 480p, 576p, 720p, 1080i, 1080p24sf
VPS3300 supports only SD-SDI formats; 480i, 576i
Analog
Component 1
Supports the following formats and resolutions:
• Component Video YPbPr; 480i, 576i, 480p, 576p, 720p, 1080i
• RGsB (RGB with sync on Green); 480p, 576p, 720p, 1080i, 800x600, 1024x768
Component 2
Supports the following formats and resolutions:
• Component Video YPbPr; 480i, 576i, 480p, 576p, 720p, 1080i
• RGBHV; 480p, 576p, 720p, 1080i, 800x600, 1024x768
• RGBS (RGB with composite sync); 480p, 576p, 720p, 1080i, 800x600, 1024x768
• RGsB (RGB with sync on Green); 480p, 576p, 720p, 1080i, 800x600, 1024x768
1
2
3
4
5
14
Component 3, Component 4
Support the following formats and resolutions:
• Component Video YPbPr; 480i, 576i
• RGBS (RGB with composite sync); 480i, 576i
• 2 x Composite (CVBS) Video and 1 x S-Video; 480i, 576i
AUDIO INPUT TERMINALS
Digital
Optical
Coaxial 1; Coaxial 2; Coaxial 3
Analog
Stereo Audio 1; Stereo Audio 2; Stereo Audio 3
VIDEO OUTPUT TERMINALS
Your display device(s) should be connected to these terminals. Crystalio II offers the following connection
configurations:
Digital
HDMI 1; HDMI 2 (both HDCP and embedded digital audio)
The HDMI (High Definition Multimedia Interface) provides the best quality video and audio output from Crystalio II.
If you are connecting to a display device that has a HDMI terminal, this is the recommended option to use. This
allows direct transmission of the video information from Crystalio II to the display without any conversion from
digital to analogue signals. Always use high quality HDMI cables, especially for longer cable runs.
Supported output resolutions:
480p, 576p, 720p, 1080i, 1080p, 1080p24sf, 640x480, 800x600, 852x480, 1024x576,1024x768,
1024x1024 ALiS, 1280x720, 1280x768, 1280x1024,1360x768, 1360x1024, 1366x768, 1368x768,
1400x788, 1400x1050,1920x1080, and customized resolutions up to 150MHz
Analog
BNC 1; BNC 2; BNC 3; BNC 4; BNC 5
Can be used either as:
• RGBHV
• RGBS (RGB with composite sync)
Supported RGBHV/RGBS output resolutions:
480p, 576p, 720p, 1080i, 640x480, 800x600, 852x480, 1024x576, 1024x768, 1024x1024 ALiS,
1280x720, 1280x768, 1280x1024, 1360x768, 1360x1024, 1366x768,1368x768, 1400x788,
1400x1050, 1920x1080, and customized resolutions up to 165MHz
• Component Video YPbPr; 480p, 576p, 720p, 1080i
AUDIO OUTPUT TERMINALS
Digital
Optical
Coaxial
Analog
Stereo Audio 1
7
8
9
10
11
12
13
14
6
15
COMPUTER/NETWORK CONNECTIVITY
These are optional/advanced connections
RS-232 DB9 Male Serial connection
Allows Crystalio II to be integrated into and controlled by third party control systems.
Infrared In/Out for room-to-room remote control
USB2.0 port 1; USB2.0 port 2
Allows Crystalio II to be upgraded using a USB thumb disk and attached external drives for media storage
expansion (model VPS3800 Pro only).
On models shipped with projectiondesign Action Model 1080 projectors, an RS-232 to USB adapter can also be
used to allow Crystalio II to be controlled by third party control systems.
RJ45 Ethernet connection
Allows Crystalio II (model VPS3800 only) to be connected to a computer network for playing media files stored
on shared folders or network servers, and network access of the internal hard disk by networked PCs.
IEEE1394 Firewire connections (model VPS3800 Pro only)
The Firewire connection is reserved for future use. If possible, activation will be carried out by a future firmware
update. Please check future firmware updates for information.
2.3 REMOTE CONTROL
There are two remote controls; one for main Crystalio II functions and one for media player functions on
Crystalio II model VPS3800 Pro (please refer to the Crystalio II Media Player Supplementary Guide for detailed
information about the Media Player and the remote control).
2.3.1 MAIN CRYSTALIO II REMOTE CONTROL
The main Crystalio II remote control is equipped with a motion sensor. Backlight automatically turns on when
the remote control is picked up.
18
19
16
17
15
16
1 OSD group keys
Keys for OSD operations are:
• Menu - enters and exits the on-screen display (OSD)
• Arrow keys: Up, Down, Left,
Right - selects different items,
or adjusts values
• OK - confirms the selected
item, or performs an action
• Back - goes back to the previous
step or previous OSD page
When not in OSD menu, some keys have different functions:
• OK - shows the Crystalio II status information:
• Input:
• Input source name, or user defined source name
• Format, or resolution
• Film, or Video source
• Output:
• Output port name, or user defined output name
• Format, or resolution
• Screen Shape
• Image:
• Aspect Ratio
• Overscan
• Deinterlace:
• Faroudja mode if source is SD and DCDi is enabled (see Section 5.2.10)
• VXP mode if source is HD
• Firmware version
• Down - selects the next input source
• Up - selects the previous input source
• Left - decreases image brightness by 1
• Right - increases image brightness by 1
2 Quick Mini Menu Selection
When these keys are pressed, a mini menu selection list pops up on
screen. The following mini menu options are available:
• Input - selects the input source
• Output - selects the primary output port
• Picture - adjusts Brightness, Contrast, Color Temp, Saturation, Hue
• A/R - selects the image aspect ratio
• i to P - selects the deinterlace method.
• when input is HD, sets VXP deinterlace method
• when input is SD and DCDi is enabled, sets Faroudja FLI2300 deinterlace method
Options are labeled by numbers and user can select options by pressing number keys directly.
See “Number Keys” below.
3 Number Keys
When in numeric entry box, pressing number keys enters the
number directly
• Pressing Up arrow key will increase the numeric value by 1
• Pressing Down arrow key will decrease the numeric value by 1
• Pressing OK key confirms the numeric entry
• Pressing the Back key will cancel the numeric value entered,
and escape from the numeric entry box
17
When in text entry box, pressing number keys enters the associated characters. For example, pressing the 2
key will enter “A”. Pressing the 2 key again within a short period of time will change “A” to “B”. Pausing between
key presses will confirm the selection and the highlighted area will move to the next character. The exact
character sequences of pressing the number keys are:
• 1 key: “1”, “-”, “(“, “)”, then “1” again
• 2 key: “A”, “B”, “C”, “2”, “a”, “b”, “c”, then “A” again
• 3 key to 9 key: similar to 2 key but taking you through the rest of the alphabet
• 0 key: “0”, “ “, then “0” again
• Pressing the Up arrow key will change the character to the previous letter
• Pressing the Down arrow key will change the character to the next letter
• Pressing OK key confirms the text entry
• Pressing the Back key will clear the current character entered; the highlight
will move left to the previous character position
When in Quick Mini Menu Selection, pressing a number key selects one of the options directly
(no need to use arrow key followed by OK).
When not in OSD mode, pressing number keys will perform the following operations:
[1] : Input Select HDMI1
[2] : Input Select HDMI2
[3] : Input Select HDMI3
[4] : Input Select SDI1
[5] : Input Select Component1
[6] : Input Select Component2
[7] : Image Aspect Ratio 4:3
[8] : Image Aspect Ratio 16:9
[9] : Image Aspect Ratio NLS
[0] : Image Gamma Adjust OSD Setup
4 Other keys
On: Power on
Off: Power off
Light:
• Turns on Crystalio II Front Panel LCD light for a short time
• When in OSD menu, toggles Hide/Show of the whole OSD
(note that the OSD menu will still exit after the time-out period)
Profile: Video Profile recall
Macro: Macro recall
Passthru: Toggles the current input source between passthru mode and normal processing mode
18
3.1 COMPATIBLE EQUIPMENT
In simple terms, Crystalio II serves as a video processor which enhances video signals from source devices and
then delivers the enhanced video signal to the display devices.
Crystalio II is compatible with:
Any source device capable of outputting:
• Composite Video
• S-Video
• RGsB (RGB with sync on Green)
• RGBS (RGB with Composite Sync)
• Component (YPbPr)
• VGA (HD15 RGBHV)
• Digital DVI
• SDI (Serial Digital Interface)
• HDMI (High Definition Multimedia Interface)
• HD-SDI (High Definition Serial Digital Interface. Model VPS3800 Pro only)
Any analog or digital display device capable of accepting input in the form of:
• Analog RGBHV
• Analog RGBS (RGB with composite sync)
• Analog Component (YPbPr)
• Digital HDMI
• Digital DVI (With suitable adaptor or HDMI>DVI cable)
3.2 MAINS
Caution: Connect Crystalio II to a power point using the mains cable provided.
3.3 VIDEO INPUTS
Crystalio II includes a comprehensive set of input terminals to allow you to connect a wide range of video
sources. Please refer to Section 2.2 for the supported input resolutions of each input port.
For the best results you should:
• use the highest quality output that your video source provides
• use high quality cables for all connections
When deciding on which output to use from your device, use the following list as a guideline
(with highest quality being first):
High Definition
1 HD-SDI - A direct digital broadcast-quality connection.
2 HDMI - A direct digital connection available on many high definition consumer devices.
3 Component (YPbPr) - An analog connection capable of carrying high definition signals.
Standard Definition
1 SD-SDI or HDMI - (a direct digital connection from a compatible set top box or DVD player).
2 RGB (RGBHV/RGsB/RGBS) - often available from set top boxes, DVD players, games consoles etc.
3 Component (YPbPr) - typically available on mid-range to high-end DVD players and some games
consoles.
4 S-Video - a general purpose connection found on many devices. Sometimes incorrectly referred
to as SVHS.
5 Composite - the most common and lowest performing video connection.
3. HARDWARE INSTALLATION
19
TIPS: It is recommended that you try to bypass any internal processing in your source by choosing the output
signal that matches the media type. For example, choose the interlaced output from your DVD player or
standard definition set-top-box instead of the progressive (e.g. 480i instead of 480p). This leaves the conversion
from interlaced video to progressive video to be performed by Crystalio II, which has sophisticated processing
dedicated to this task.
3.4 VIDEO OUTPUTS
For maximum performance you should use the digital connection where possible.
The reason for this is that the display of a digital device (for example a plasma panel, TFT monitor or
LCD/LCOS/DLP projector) is built up of a grid of a fixed number of elements or pixels, which are all directly and
individually controlled by the internal digital electronics of the display. Using the HDMI interface of the display
allows these individual pixels to be directly controlled by Crystalio II, bypassing the internal picture processing
electronics of the display device, and thereby producing more detailed and accurate images.
When deciding on which output to use from Crystalio II, use the following list as a guideline (highest quality first):
1 HDMI (a direct digital connection from Crystalio II to the display device).
2 RGBHV/RGBS.
3 Component video.
Some digital displays may not accept their native resolution via HDMI. In these cases better results
may be possible using the display’s VGA or computer RGBHV input. This may allow 1:1 pixel mapping to be
achieved (See Section 4.6.1).
20
4.1 CONFIGURE YOUR VIDEO SOURCE
Even if your standard definition video source has the option to output progressive video (denoted by a number
and then the letter ‘p’, for example 480p), for maximum results, it is recommended to disable such an option
and select interlaced video mode instead (denoted by a number and then the letter ‘i’, for example 480i).
Crystalio II features state-of-the-art technology specifically designed to convert interlaced video into progressive
video. This will usually deliver higher performance than the converter built into your source device.
Similarly, your high definition source may have an option to scale the incoming signal to a fixed output
resolution. Again, it is advisable to turn this feature off as the sophisticated scaling algorithms in Crystalio II
will produce far cleaner results.
4.2 SWITCH ON CRYSTALIO II
Press the POWER button on the front panel. The Power LED should show green and the LCD display
illuminates. Note that you will need to wait for approximately 15 seconds for Crystalio II to initialize and for
video to display.
If you do not see video as expected, refer to Section 8: Troubleshooting.
The default video output of Crystalio II is 720p. Most high definition displays can lock to 720p
which should then enable you to use the OSD to correctly configure Crystalio II.
4.3 SELECT INPUT VIDEO SOURCE
Using the remote control
Press the Menu remote control key to enter the OSD menu, then select Input Select in the Input sub-menu.
Select the type of input port via which your input device has been connected and press OK to confirm.
OR
Press the Input remote control key and a mini menu selection list pops up. Select the type of input port
via which your input device has been connected and press OK to confirm.
OR
Using the front panel control
1 Press OK button to start Main Menu
2 Select Input and choose Input Select
3 Choose input port via which your input device is connected
4 Press OK button to confirm
OR
Press the INPUT front panel button to cycle through the various input terminals and stop at the one
through which your input device is connected.
4.4 SELECT PRIMARY OUTPUT PORT
Using the remote control
Press the Menu remote control key to enter the OSD menu, then select Output Select in the Output sub-menu.
Select the output terminal via which your display device has been connected and press OK to confirm.
OR
Press the Output remote control key and a mini menu selection list pops up. Select the output terminal via
which your display device has been connected and press OK to confirm.
4. BASIC SETUP
21
OR
Using the front panel control
1 Press OK button to start Main Menu
2 Select Output and choose Output Select
3 Choose output terminal to which your display device is connected
4 Press OK button to confirm
OR
Press the Output front panel remote control key to cycle through the various output terminals and stop at the
one through which your display device is connected.
4.5 SET OUTPUT FORMAT/RESOLUTION
Using the remote control
Press the Menu remote control key to enter the OSD menu, then select Resolution in the Output sub-menu.
Choose Standard Format or Fixed Resolution of the display device being connected in and press the
action button to confirm.
OR
Using the front panel control
1 Press OK button to start Main Menu
2 Select Output and choose Resolution
3 Choose output resolution which your display device requires
4 Press OK button to confirm
4.6 BASIC SETUP TIPS FOR DIGITAL DISPLAYS/PROJECTORS
4.6.1 PIXEL PERFECT
Every pixel-based digital display has a native resolution*, so any video source displayed needs to be scaled
from its original resolution (size) to the native resolution of the display for optimum results. If the Crystalio II
output resolution is mapped to the display in 1:1 mode, or pixel perfect mode, this ensures all video processing
and scaling is done by Crystalio II. This is very important because:
• It ensures that the display’s internal scaler is bypassed, allowing you to benefit from the image
processing power of Crystalio II
• It avoids double scaling and processing done to the video source, which would introduce video
artifacts, especially during smooth motion e.g. camera pans
* A display’s native resolution is expressed as number of pixels wide by number of pixels high. For example many DLP projectors are 1280 x
720, so for optimum results all video should be scaled to that number of pixels. Think of this as addressing the exact number of active pixels;
once this has been done as detailed below you have achieved 1:1 mapping, or pixel perfect mode.
To make sure Crystalio II’s output is pixel perfect, please make use of the Crystalio II internal video test patterns
to confirm 1:1 pixel mapping has been achieved. See the examples overleaf:
22
Video Test Pattern: Horizontal Line 50
Pixel Perfect
Video Test Pattern: Horizontal Line 50
Not Pixel Perfect
Video Test Pattern: Vertical Line 50
Pixel Perfect
Video Test Pattern: Vertical Line 50
Not Pixel Perfect
Video Test Pattern: Pixel Magic
Pixel Perfect
Video Test Pattern: Pixel Magic
Not Pixel Perfect
If viewing these images on a computer screen please use the zoom function in
Adobe Acrobat Reader to properly view the differences between these images
TIP: If you think that you have set Crystalio II to your display's native resolution, yet the images above still don't appear
correctly, try using the 'Horizontal Line 50' pattern and making small adjustments to your display's V-Size. There may be a
setting where it 'snaps' into focus. Then try 'Vertical Line 50' and adjust your display's H-Size. Once you think you have the
patterns in focus, select the 'Overscan' test pattern and use your display's H- and V-Position controls to center the image.
23
4.6.2 OUTPUT 50HZ OR 60HZ AUTOMATICALLY
If your display supports 50Hz input and can produce real 50Hz refresh rate video image*, it is better to
configure Crystalio II to output 50Hz resolution when source video is 50Hz (i.e. PAL signal); and output 60Hz
resolution when the source video is 60Hz (i.e. NTSC signal). This is because the output video will be perfectly
smooth if the refresh rate of video image displayed is the same as that of the video source. Otherwise, you will
see slight jerkiness of subject movement, especially when there are camera pans.
* Some displays that support 50Hz input will convert the 50Hz video back to the display’s native 60Hz (the majority of pixel-based
displays have a native 60Hz vertical refresh rate) and produce a 60Hz refresh rate video image. You can verify this if you have
configured Crystalio II to output the same refresh rate as the input; if with a 50Hz source you see jerkiness in the image, your
display’s internal scaler may be performing a frame rate conversion to 60Hz
To configure Crystalio II to output 50Hz resolution when input refresh rate is 50Hz, and output 60Hz resolution
when input refresh rate is 60Hz, follow the steps below:
• Press the Menu remote control key to enter the OSD (On Screen Display) menu
• Select Output then DynamicVP
TM
(if you can’t see the DynamicVPTMoption, select
the Advanced Option under System sub-menu and turn Advanced Option ON first)
• Turn the DynamicVP Mode ON
• In the first line of rules under When Input, select 50Hz
• In the first line of rules under Action/Resolution, select Output Resolution
• In the dropdown list of resolutions, select your display’s native resolution;
then in the dropdown list of refresh rates, select 50Hz
• In the second line of rules under When Input, select 60Hz
• In the second line of rules under Action/Resolution, select Fixed Resolution
• In the dropdown list of resolutions, select your display’s native resolution;
then in the dropdown list of refresh rates, select 60Hz
• Press the Menu remote control key to exit the OSD menu
4.6.3 BASIC CALIBRATIONS
Crystalio II has been designed and built to output broadcast standard video. You can even use Crystalio II as a
reference video signal generator. You should therefore make use of the internal video test patterns to calibrate
the video output level and color balance of your display. Once your display is accurately showing grayscale and
color, each individual source device can be fine-tuned to match.
Good results can be achieved following the steps in this section. However, more accurate results can be
achieved by using a color analyzer (colorimeter) at the screen to take measurements. If you are not confident
with this process, your dealer or a calibration specialist may be able to calibrate the system for you.
4.6.3.1 DISPLAY VIDEO LEVEL AND COLOR CALIBRATION
Step 1: Reset Crystalio II’s video settings to the default values, which include:
• Contrast, Brightness (default = 0)
• Red, Green, Blue Offsets and Gains (default = 0)
• Gamma correction (default type Standard, and value = 0)
Step 2: Select a correct output video level from Crystalio II’s HDMI output port:
• Press the Menu remote control key to enter the OSD (On Screen Display) menu
• Select Output then Output Port Configuration. You should see output configuration options of HDMI
output ports (If not, select the Advanced Option under System sub-menu
• and turn Advanced Option ON first)
• If your display is expecting video from a video source with HDMI output, configure Crystalio II’s HDMI
output level as HDMI Standard
• If your display is expecting video from a normal consumer AV product, configure Crystalio II’s HDMI
output level as Video Level (16-235)
• If your display is expecting video from a PC, configure Crystalio II’s HDMI output level as PC Level
(0-255)
24
• If you are not sure which video level is correct, leave it at the default setting. Or, if the picture is
excessively dark or very washed out, try changing the HDMI output level to see which one looks
correct
Step 3: Calibrate the black level (brightness) of your display:
• Show the internal video test pattern Black 1-3% (under the OSD menu System and Video Test Patterns)
• Turn the brightness setting of your display down excessively so that the whole screen is black
• Turn the brightness up until you can barely see the difference of the 1%, 2%, and 3% bars
Step 4: Calibrate the white level (contrast or peak white level) of your display:
• Show the internal video test pattern White 97-99%
• Turn the contrast setting of your display up excessively so that you see the whole image as white
• Turn the contrast down until you can barely see the difference between the 97%, 98%, and 99% bars
Step 5: Calibrate the color balance of your display:
• Show the internal video test pattern Cross Gray Steps, and pay attention
to the black bar and white (100 IRE) bar
• Adjust Red, Green, and/or Blue offset/bias settings of your display to fine
tune the color of the black bar if it doesn’t look a neutral black*
• Adjust Red, Green, and/or Blue gain settings of your display to fine tune
the color of white bar if it doesn’t look a neutral white*
*Aim to lower the color you see as dominant rather than increasing the other two
Step 6: Repeat steps 3 to 5 until the brightness and contrast settings don’t need changing,
and the R/G/B offset and R/G/B gain settings of your display are satisfactory.
4.6.3.2 SOURCE VIDEO LEVEL AND COLOR CALIBRATION
Once you have calibrated your display for correct video output levels and color balance, you don’t need to
calibrate your video sources if they also have correct video level and color balance. In practice, however,
most of the video sources will still have some form of problem with video levels or color balance and we
have to calibrate them one by one for perfect results.
To calibrate video sources, we ideally need test patterns originating from the video source. This is
straightforward using readily available specialist calibration DVDs. Many HDTV stations also carry test material
at certain times of the day. In the absence of any specific test material it is difficult to calibrate accurately, as you
can only make the picture look how you expect it should be, so check several discs to gain a good balance.
Please follow the steps below for each video source connected to Crystalio II:
Step 1: Reset Crystalio II’s video settings to the default values:
• Contrast, Brightness (default = 0)
• Red, Green, Blue Offsets and Gains (default = 0)
• Gamma correction (default type Standard, and value = 0)
Step 2: For sources connected to Crystalio II’s HDMI input ports, select the correct input video:
• Press the Menu remote control key to enter OSD (On Screen Display) menu
• Select Input, then Input Port Configuration, and then press the action button.
(If you can’t find this button, select the Advanced Option under System sub-menu and turn
Advanced Option ON first)
• If your source device is equipped with HDMI output, configure Crystalio II’s HDMI input level
as HDMI Standard
• If your source device is a normal consumer AV product, configure Crystalio II’s HDMI output
level as Video Level (16-235)
• If your source device is a PC, configure Crystalio II’s HDMI output level as PC Level (0-255)
• If you are not sure what video level is correct, leave it set at Standard. Or if the picture is excessively
dark or very washed out, try changing the HDMI input level to see which one looks the best
25
Step 3: Calibrate the black level (brightness) of your video source:
• Find a video test pattern for adjusting black level, e.g. the Black Bar pattern from AVIA DVD from
Ovation Multimedia
• Turn the brightness setting of Crystalio II down excessively so that you see the whole image as black
• Turn the brightness up until you can barely see the difference between the black background and the
slightly brighter black bar (in the AVIA test pattern)
Step 4: Calibrating the white level (contrast or peak white level) of your video source:
• Find a video test pattern for adjusting white level, e.g. the Needle Pulse from the AVIA DVD from
Ovation Multimedia
• Turn the contrast setting of Crystalio II up excessively so that you see the whole image as white
• Turn the contrast down until you can barely see the difference between the white background and the
slightly darker white bar
Step 5: Repeat step 3 to step 4 until the brightness and contrast settings need not be changed,
and R/G/B Offset and R/G/B Gain settings of the video source are satisfactory
To calibrate all video sources, you must perform the above steps to all video sources.
Remember to reset Crystalio II’s video settings for each input before your calibration.
If you have two kinds of video source, which have different level and/or color balance, from a single input port
(for example a DVD player used for both NTSC and PAL discs); or you wish to have a selection of different
video setups available, you can do the calibration and store the video settings in different Video Profiles. Note
that Crystalio II has 10 different Video Profiles for each individual video input port. If you use both NTSC and PAL
video into an input you can program DynamicVP™ to automatically load the appropriate video profile depending
on the input vertical refresh rate Crystalio II detects.
Tips for calibrating sources without test patterns
• If you don’t have a test pattern for adjusting black level, select a scene with lots of dark areas (for
example, a man wearing a black jacket in a dark night background), and adjust the brightness just as
in step 3 above, using the black background and the near-black object instead of the bars test pattern
• If you don’t have a test pattern for adjusting white level, select a scene with lots of bright areas (for
example, a sunny sky with a little bit of cloud), and adjust the contrast just as in step 4 above, using
the white background and the near-white object instead of the bars test pattern
4.6.3.3 CALIBRATING COLOR TO COMPENSATE FOR DISPLAY AND SOURCE
INACCURACIES
Color calibration in Crystalio II is designed for instances where displays and sources cannot be accurately
calibrated using their own controls. It is a way of compensating for inaccuracies in connected devices.
For calibrating your display devices, there are separate RGB Gamma Correction controls and a Color
control in the Output menu.
For calibrating your source devices, there are separate RGB Gamma Correction controls and a Color
Temperature control in the Image menu.
In order to see these controls it is necessary to select the Advanced Option under the System sub-menu
and turn Advanced Option ON
Ways in which we can check for color accuracy are:
1. Check that shades of grey are really neutral (equal levels of R, G and B).
2. Check that pure R, G and B are really pure.
Sometimes it is necessary for a color measurement tool to be used at the screen to determine accurate levels.
Loading...