Pivot Mega RAIZIN User Manual

(
VS-M As of March, 2008 No.2
Voltage Stabilizer
)
Mega RAIZIN
USER'S GUIDE
Thank you for purchasing PIVOT “Mega RAIZIN”. Please read these instructions carefully before installing or using this device. Please do not lose this user’s guide, as you will held liable for the cost of reissuing it.
CAUTION
Due to vehicle exhaust emission poisoning or fire may result in a damage to humans.
Safety Precautions for Installation and Checking Operations
When the key is switched to ON, there is a possibility that the fan or belt may suddenly begin moving and cause bodily injury. When doing any work, make sure that the key is switched to OFF and when checking operation make sure not to put your face or hands in a close position which could cause bodily injury.
Improper use or disregard of these warnings may result in the injury or death of people.
Please securely fasten the product to a stable place
Make sure to install and fasten the unit to a safe place that will not become entangled in a fan or belt.
Do not crush the cable
Please do not place the unit or the wires in any place that is exposed to high temperature nor near any rotating objects such as a fan or belt. Wires may become broken causing a short and/or fire. Do not splash water on the unit.
Mega
High Capacity System & Battery Performance Monitor
Please check the contents of the package.
Double-sided
Main Unit
Do not allow water to come into contact with the unit.
The unit has been processed for water resistance but do not splash with water when washing the car and so on.
This product is for DC12V cars;
installation cannot be carried out on cars with other voltage batteries.
2 User’s Guide
M6 Nut
Tape
3
1
FEATURES
Results you can
count on
NOTE
1.The unit assesses battery performance through changes in lowest voltage readings and when it has been judged to be reduced allows the user to take necessary measures to improve performance (replacement, recharging, etc...) and thereby provide voltage stability to all electronic devices.
2.The condenser circuitry reduces electrical noise and provides a stable voltage supply to the ignition coil as well as all other electronic devices.
About Improved Performance
About Judging Battery Life
Stabilize Voltage and Know when Battery Performance is Reduced !
......
Installation of this product will lead to improvement in electrical aspects of your automobile but due to actual car and driving conditions these improvements may be negligible or in some cases no change will occur.
......
Depending on the characteristics of the battery itself even a small change in the lowest voltage reading may signal the end of a battery's life.
Voltage Stabilizer
Our newly designed three-fold (compared to Blue Raizin) large capacity condenser and our newly designed filter circuitry results in decreases in both circuitry noise and high frequency impedance which results in a more stable supply of voltage to the ignition coil and all electronic devices as well as improvements in power loss.
INSTALLATION PROCEDURE
WARNING
Please install safely and surely by following these instructions. In particular, please be very careful about connecting the and cables. Mixing these up will cause damage to the product.
Make sure that and are connected correctly.
BASIC WIRING
Battery terminal
Cable
Digital Display
Things to prepare
.
Wrenches (Socket Wrench . Combination Wrench)
.
Vinyl Electrical Tape . Cloth . Absorbing Agent
Installation Preparation
1
Remove the cable from the battery terminal.
1
Insulate the battery terminal with vinyl tape.
2
CAUTION
To prevent making any mistakes with the and
and causing a short during installation,
please make sure to insulate.
2
Installing the RAIZIN unit.
Decide installation place.
1
.
Without forcing, make sure you can connect
the two cables to the correct terminals.
.
Make sure the installation place is a flat
surface where the unit can be fixed with double-sided tape.
Ex) The top or side of the battery or any other
flat surface near the battery. (fuse box, etc...)
If you're installing on the side surface, install so
the cables go out the bottom.
that
Do not to install in areas subject to water.
Circuitry has waterproof coating. But do not to install in areas subject to water or spray with water.
.
If you install with the cables
going out the top, water may enter the unit and cause damage. Make sure
install with cables
to
going out the bottom of the unit.
2
Clean off all oil and dirt from the bottom of the main unit and affix the double-sided tape included in the kit.
3
Clean off all oil and dirt from the installation place and fasten the main unit.
If you're installing on the top surface, make sure the car hood will not to hit the unit when closed.
.
Do not allow water to come
into contact with the unit.
If it is a good chance of water
coming into contact, please
Cable terminal
Battery terminal
Insulate with vinyl tape.
cover with waterproof sheeting.
Waterproof Sheeting, etc.
CAUTION
1.If you're installing on the side surface, the double-sided tape will take about two hours to become secure. During that time do not allow any vibration to the unit.
2.Reinstalling will cause the tape's adhesive strength to weaken, so please do not to it.
CLEAN TO REMOVE
OIL & DUST
A World's First: View Battery Performance via Lowest Voltage Display
Displaying two types of voltage, both "Real" and "Lowest" Voltage (world first) at engine start makes it easy to see battery life and loss in battery performance. This also helps to protect against trouble caused by shortages in voltage to various electronic devices.
M6 Nut
Red Colored Insulation Cap
RAIZIN
Unit
Connect the Cable
3
Remove the cover from the
1
Connect the unit's insulation cap) to the terminal of the
.
Fasten with an M6 nut to the original bolt.
.
Fasten between the original nut and the terminal.
Replace the cover after completing the connection.
2
If the cover does not insulate properly, please use vinyl tape to ensure proper insulation.
Check Wiring
4
Remove the vinyl tape from the terminal of the battery.
1
Connect the minus cable (with blue cap) to the battery's minus terminal.
2
If the wiring has been completed correctly the voltage should appear and after ten seconds
3
automatically shut off.
.
If voltage is not displayed = please check the connection and make sure and
WARNING
Connect the unit's
5
Connect the Cable
1
Properly connect the cable terminal to the battery terminal.
2
Connect the unit's insulation cap) to the terminal of the
.
Fasten with an M6 nut to the original bolt.
.
Fasten between the original nut and the terminal.
If an earth terminal is installed, connect the cable to the terminal.
(See [BASIC WIRING])
6
Arranging the Cables
Battery terminal
M6 Nut
Blue Colored Insulation Cap
Cable
terminal of the battery.
cable (one with red colored
are correct.
Please make sure to check about connecting the and cables. Mixing these up will cause damage to the product.
cable
Due to characteristics of the product, upon contact of the RAIZIN'S
current sparks may be emitted. This is not a defect.
cable (one with blue colored
Arrange the cables with the lock ties included.
If an earth terminal is installed...
Earth Terminal
Battery terminal
Cable terminal
Original Bolt
Red Colored
Insulation Cap
Cable
M6 Nut
battery cable.
Cable
Battery terminal
Sparking upon Contact
or upon the shorting of the flow of
battery cable.
to the battery's
Battery terminal
Original Bolt
M6 Nut
Blue Colored
Insulation Cap
Cable
ASSESSING BATTERY PERFORMANCE
The lowest voltage at engine start is measured and if a change (lower measurement) is detected the battery's performance and life will be judged to have been reduced.
HOW TO CHECK VOLTAGE
Judging Reduced Battery Performance (Lowest Voltage)
Judgments about reduced battery performance (life) can be made by checking the lowest voltage reading for a new battery at engine start and using that reading for comparison. In order to do this, this unit measures and displays lowest voltage at engine start and thereby helps to prevent the following troubles associated with reduced battery performance.
Possible Causes Reduced electronic device output caused by unstable voltage supply. Reduced electronic device output caused by increased noise. Reduced output due to lack of battery charge.
Trouble Poor mileage, reduced torque, poor starting, sound and reduced light brightness. Reductions in mileage and torque as well as in sound quality due to increase in noise. Troubles in starting engine and dead batteries.
Voltage(V)
About Judging Reductions in Performance from Changes in Voltage
If the difference in lowest voltage measurements for a new battery falls
1V to 1.5V , the battery's performance can be deemed to be reduced and
we strongly suggest taking the battery to a repair shop for checking and recharging.
By "new battery" we mean a battery that has not been used for more than six months; if a battery has been used for more than six months a change of
0.5V to 0.8V should be viewed as a sign that performance has been
reduced and the battery should be checked.
Judgment Method
Engine Start
ON
Check the Lowest Voltage of New Battery
Ex : 7.5V (Blink)
Periodic Check
0.7V reduction since new
Ex : 6.8V (Blink)
2.1V reduction since new
Ex : 5.4V (Blink)
Normal
Reductions in
Performance
15 14 13 12 11 10
9 8 7 6
0 5 10 20 (S)
ACC IG ON Engine Start
Real Voltage
Engine Running
Normal Range
1~1.5V
Reduced Battery
Performance
(Check Required)
Lowest Voltage
New Battery Ex : 7.5V
Please have battery checked periodically (every month) or if the following occurs:
.
The engine seems not to start well
.
The lights seem dark .The battery frequently dies out
Usable
Note that this method can only provide a rough guideline and battery life varies greatly depends on the individual characteristics of batteries and automobiles.
Also note that even with properly working batteries, large
Check
reductions (about 1V) in lowest voltage readings can occur when outside temperatures are low (below 5 after having forgotten to turn off the lights.
Note that this measurement method can only provide a rough guideline and that lowest voltage readings and battery life varies greatly depending on the individual characteristics of the battery being used.
) or starting
Checking while Engine is Running (Real Voltage)
If voltage falls outside an acceptable range while the engine is running one of the following may be the reason and a check should be carried out.
If it is too high (15V or more)
Possible
Causes Trouble
The alternator is broken (Regulator)
Lowered performance of electronic devices or reduced battery life.
If it is too low (11.5V or less)
Possible
Causes Trouble
1. The fan belt is too loose or is torn.
2. The alternator or battery does not work properly. Deterioration in mileage, torque, starting, sound and light brightness.
Measurement Method
When the engine is started, two types of voltage measurement (lowest voltage at engine start and real voltage) will be displayed for a short time (about one minute) and then will automatically shut off.
Engine Start Voltage Displays (Displayed alternately for about sixty seconds)
Lowest Voltage (3 Seconds)
Real Voltage (5 Seconds)
ON
Ex : 7.5V (Blink) Ex : 7.5V (Blink)Ex : 14.2V (Light up)
If you wish to re-measure the lowest voltage at engine start please perform only after the display has automatically turned off.
Lowest Voltage (3 Seconds)
Real Voltage (5 Seconds)
Ex : 13.8V (Light up)
After 60
seconds
Note that if you are using a remote control starter to start your engine, the display will turn off after about one minute and cannot be viewed.
After 60 seconds
Automatically
turned off
PIVOT CORPORATION
87-3, Shimookada Okada, Matsumoto-shi, Nagano, 390-0313 Japan TEL0263-46-5901 http://pivotjp.com/
2
Loading...