PITSOS WKP1000D8 Instruction Manual And Installation Instructions

HQ,QVWUXFWLRQ0DQXDODQG,QVWDOODWLRQ,QVWUXFWLRQ

WKP1000D8

Washing machine

2

Your new washing machine

You have chosen a Pitsos washing
machine.

Please take a few minutes to read and
become familiar with the advantages of
your washing machine.

To meet the high quality demands
required by Pitsos, every washing
machine that leaves our factory is
carefully checked to ensure that it
functions correctly and is in perfect
condition.

For more information on our products,
accessories, replacement parts and
services, see our website
www.pitsos.gr or contact our after-sales
service centres.

If the operating and installation
instructions describe different models,
any differences will be pointed out at the
relevant points in the text.

Read these operating and installation
instructions before switching on the
washing machine.

Display rules

: Warning!

This combination of symbol and signal
word indicates a possibly dangerous
situation. Not heeding the warning can
cause death or injuries.

Caution!

This signal word indicates a possibly
dangerous situation. Not heeding the
caution can cause property and/or
environmental damage.

Note/tip

Information about the optimum use of
the appliance/any other useful
information.

1. 2. 3. / a) b) c)

The steps are represented by numbers
or letters.

■ / -

Lists are represented by a small box or
a dash.

Intended use en

3

Contents

en Instruction Manual and Installation Instructions

8Intended use

Intended use

■ For private domestic use only.

■ The washing machine is suitable for

washing machine-washable fabrics
and hand-washable wool in
detergent solution.

■ To be operated with cold mains

water and standard detergents and
care products which are suitable for
use in washing machines.

■ When measuring out the amount of

all detergents, additives, care
products and cleaning agents,
always follow the manufacturer's
instructions.

■ The washing machine may be used

by children over the age of 8 years
and by persons with reduced
physical, sensory or mental capacity
or by persons with a lack of
experience or knowledge if they are
supervised or have been instructed
by a responsible person.
Children must not carry out any
cleaning or maintenance work
without supervision.

■ Keep children under the age of 3

years away from the washing
machine.

■ This appliance is intended for use up

to a maximum height of
4000 metres above sea level.

■ Keep pets away from the washing

machine.

Before operating the appliance: Read
the installation and operating
instructions and all other information
enclosed with the washing machine,
and use the machine accordingly.
Retain the documents for subsequent
use or for subsequent owners.

( Safety instructions

Safety instructions

Electrical safety

:Warning

Danger of death!

There is a risk of electric shock
if you touch live components.

■ Never touch or hold the

mains plug with wet hands.

■ Only pull out the mains cable

by the plug and never by the
cable, as this could damage
it.

Risk of injury

:Warning

Risk of injury!

■ When the washing machine

is lifted by its protruding
parts (e.g. the washing
machine door), the
components may break off
and cause injuries.
Do not lift the washing
machine by protruding parts.

■ If you climb on the washing

machine, the worktop may
break and cause injuries.
Do not climb onto the
washing machine.

■ If you lean on the washing

machine door when it is
open, the washing machine
may tip over and cause
injuries.
Do not lean on the washing
machine door when it is
open.

en Safety instructions

4

■ Reaching into the drum

when it is turning can cause
injuries to hands.
Do not reach into the drum
when it is turning.
Wait until the drum has
stopped turning.

:Warning

Risk of scalding!

When you are washing at high
temperatures, there is a risk of
scalding if you come into
contact with hot water e.g. if hot
water is being drained into a
wash basin.
Do not reach into the hot
detergent solution.

Safety for children

:Warning

Danger of death!

If children play with the washing
machine, they may get into life­threatening situations or injure
themselves.

■ Do not leave children

unattended near the washing
machine.

■ Do not let children play with

the washing machine.

:Warning

Danger of death!

Children may lock themselves
in appliances, putting their lives
at risk.
For appliances that have
reached the end of their service
life:

■ Disconnect the mains plug.

■ Cut through the mains cable

and remove it, along with
plug.

■ Destroy the lock on the

washing machine door.

:Warning

Risk of suffocation!

Children may become wrapped
in packaging/film or packing
parts if allowed to play with
them, or they may pull them
over their heads and suffocate.
Keep packaging, film and
packaging parts out of the
reach of children.

:Warning

Risk of poisoning!

Detergents and care products
may be poisonous if
consumed.
Keep detergents and care
products out of the reach of
children.

:Warning

Eye/skin irritation!

Detergents and care products
may cause irritation if they
come into contact with the eyes
or skin.
Keep detergents and care
products out of the reach of
children.

:Warning

Risk of injury!

When you wash at high
temperatures, the glass in the
washing machine door gets
hot.

Environmental protection en

5

Do not let children touch the
hot washing machine door.

7 Environmental

protection

Environmental protection

Packaging/used appliance

Tips on economical use

■ Always fill the appliance with the

maximum amount of laundry for the
relevant programme.
Overview of programmes

~ Page 11

■ Wash normally soiled laundry

without a prewash.

■ Save energy and detergent when

washing lightly and normally soiled
laundry. ~ Page 10

■ Energy-saving mode: The display

panel lighting goes out after a few
minutes and Start flashes. To
activate the lighting, press any
button.
Energy-saving mode is not activated
if a programme is running.

■ If the laundry is subsequently dried

in a tumble dryer, select the spin
speed according to the tumble dryer
manufacturer's instructions.

)

Dispose of packaging in an
environmentally-responsible
manner.
This appliance is labelled in
accordance with European
Directive 2012/19/EU
concerning used electrical and
electronic appliances (waste
electrical and electronic
equipment - WEEE).
The guideline determines the
framework for the return and
recycling of used appliances
as applicable throughout the
EU.

en Main points in brief

6

Y Main points in brief

Main points in brief

--------

--------

--------

--------

1 @ @ @

Connect the mains
plug.

Turn on the water
tap.

Sort the laundry. Open the door.

2 @ @ @

Select a programme
e.g. Cottons.

Observe the
maximum load on
the display panel. *

Load the laundry . Close the washing

machine door.

3 @ @ @

Add detergent. Change the

programme default
settings, if
necessary.

Select additional
settings, if
necessary.

Start the
programme.

4 @ @ @

Programme end Open the washing

machine door and
remove the laundry.

Set the programme
selector to stop..

Turn off the water
tap (for models
without Aqua-Stop).

* depending on model

Getting to know the appliance en

7

* Getting to know the appliance

Getting to know the appliance

Washing machine









#

6 7

( Detergent drawer ~ Page 15 8 Washing machine door with window handle
0 Controls/display elements 9S Open the washing machine door

9T Close the door
@ Service flap

en Getting to know the appliance

8

Control panel

Display panel





#

+

( Programme selector for selecting a
programme and for switching the machine on and
off

@ V + quick (SpeedPerfect), 2 Πρόπλυση
(Pre-Wash)

Additional programme settings

0 Display panel for settings and information H Ü έναρξη/παύση (Start/Reload), for

starting, interrupting (adding laundry) and
cancelling a programme

8 στύψιμο (Spin speed), λήξη σε ("Ready
in")

For changing the programme default settings

Settings for the selected programme

– – –...1000* Spin speed;

* max. speed depends on the model

in rpm (rotations per minute);
– – – = rinse hold (without final spin)

1:30 Programme duration Depends on the programme selection in h:min

(hours:minutes)

1 - 24 Ready in Programme end after ...h (h = hours)

8.0 Max. load in kg

Status indicators for the programme progress (programme sequence):

r ' 0 End: Wash, rinse, spin, programme duration or end

Ä : Open the washing machine door, add laundry ~ Page 17

@: Childproof lock ~ Page 16

Laundry en

9

Z Laundry

Laundry

Prepare the laundry

Caution!
Damage to the appliance/fabrics

Foreign objects (e.g. coins, paperclips,
needles, nails) may damage the laundry
or components in the washing machine.

You should therefore note the following
tips when preparing your laundry:

■ Empty any pockets.

■ Look out for metal items (paperclips,

etc.) and remove them.

■ Wash delicates in a laundry bag

(tights, underwired bras, etc.).

■ Close any zips; button up any cover

buttons.

■ Brush sand out of pockets and

collars.

■ Remove curtain fittings or place

curtains in a laundry bag.

Sorting laundry

Sort your laundry according to the care
instructions and manufacturer's
information on the care labels:

■ Type of fabric/fibre

■ Colour

Note: Laundry can discolour or not

be cleaned correctly. Wash white
and coloured laundry separately.
Wash new bright fabrics separately
the first time you wash them.

■ Soiling

Wash laundry with the same level of
soiling together.

You can find examples of levels of
soiling on
– Light: Do not pre-wash, select

the V SpeedPerfect setting if

necessary
– Normal
– Heavy: Load less laundry, select

a programme with pre-wash
– Stains: Remove/pre-treat stains

while they are fresh. First, dab the

stain with soapy water/do not

rub. Then wash the items of

laundry with the appropriate

programme. Stubborn/dried-in

stains can sometimes only be

removed with several washes.

■ Symbols on the care labels

The numbers in the symbols indicate
the maximum washing temperature
which may be used.
– M: Suitable for a normal

washing process; e.g. Cottons

programme
– U : A gentle washing process is

required; e.g. Easy-Care

programme
– V : An especially gentle washing

process is required; e.g.

Delicates/Silk programme
– W : Suitable for washing by

hand; e.g. W Wool programme
– Ž : Do not wash the laundry in

the machine.

en Detergent

10

C Detergent

Detergent

Correct selection of detergent

The care label is crucial for selecting
the correct detergent, temperature and
treatment of the laundry. ~ See also
www.sartex.ch

If you visit www.cleanright.eu, you will
find further information on detergents,
care products and cleaning agents for
domestic use.

■ Standard detergent with optical

brighteners

Suitable for boil-washable white
laundry made from linen or cotton
Programme: Cottons/
cold - max. 90 °C

■ Detergent for colours without

bleach or optical brighteners

Suitable for coloured laundry made
from linen or cotton
Programme: Cottons/
cold - max. 60 °C

■ Detergent for colours/delicates

without optical brighteners

Suitable for coloured laundry made
from easy-care fibres, synthetic
fibres
Programme: Easy-Care/
cold - max. 60 °C

■ Detergent for delicates

Suitable for delicate, fine fabrics, silk
or viscose
Programme: Delicate/Silk/
cold - max. 40 °C

■ Detergent for woollens

Suitable for wool
Wool programme/
cold - max. 40 °C

Saving energy and detergent

For light and normal soiling, you can
save energy (lower washing
temperature) and detergent.

Note: When measuring the amount of

all detergents/additives/care products
and cleaning agents, please always
check the manufacturer's instructions
and information. ~ Page 15

Saving Soiling/note

Reduced temper­ature and deter­gent quantity as
per the recom­mended dosage

Light

No visible dirt or stains. Cloth­ing has taken on some body
odour, e.g.:

■ Light summer/sports

clothing (worn for a few
hours)

■ T-shirts, shirts, blouses

(worn for up to one day)

■ Guest bed linen and hand

towels (used for one day)

Normal

Visible dirt or a few light
stains, e.g.:

■ T-shirts, shirts, blouses

(sweat soaked, worn a
few times)

■ Towels, bedding (used for

up to one week)

Temperature as
per the care label
and detergent
quantity as per
the recom­mended dosage
for heavy soiling

Heavy

Dirt and/or stains clearly visi­ble, e.g. tea towels, baby
items, work clothing

Overview of programmes en

11

/ Overview of programmes

Overview of programmes

Programmes on the programme selector

Programme/type of laundry/information Settings

Name of programme

Short explanation of the programme or the fabric for which it is suita­ble.

Max. load;
* Reduced load for V SpeedPerfect

setting

Temperature that can be selected

Spin speed that can be selected;
** Max. spin speed, depending on

the model

Possible programme settings

Βαμβακερά (Cottons)
Hard-wearing fabrics, heat-resistant fabrics made of cotton or linen
Βαμβακερά +ecologic (Cottons + eco) 40 °C, 60 °C: Programme

for saving energy with a washing result comparable to that of the
standard programme

Note: The V SpeedPerfect setting is suitable as a short programme

for lightly soiled laundry.

Max. 8 kg/5* kg

20 °C - 90 °C

– – – ... 1000** rpm

V, 2

ξέβγαλμα (Rinse)
Extra rinse with spin

Max. 8 kg

-

– – – ... 1000 rpm

στύψιμο/αντληση (Spin/Drain)
Extra spin with speed that can be selected
If only the Drain cycle is required, set the spin speed to – – –.

Max. 8 kg

-

– – – ... 1000** rpm

W μάλλινα (Wool)
Hand or machine-washable fabrics made of wool or that contain

wool;
particularly gentle wash programme to prevent shrinkage of laundry,

with longer programme breaks (fabrics rest in the detergent solu­tion)

Notes

■ Wool is of animal origin, e.g.: Angora, alpaca, llama, sheep.

■ Use a detergent which is suitable for machine washing wool.

Max. 2 kg

30 °C

– – – ... 800 rpm

-

en Overview of programmes

12

Starching

Note: Laundry must not be treated with

fabric softener.

Starching is possible in all wash
programmes if liquid starch is used.
Measure starch into compartment M in
accordance with the manufacturer's
instructions (clean first if necessary).

Dyeing/bleaching

Dye should only be used in normal
household quantities. Salt may damage
stainless steel. Always follow the dye
manufacturer's instructions.

Do not use the washing machine to
bleach clothes.

Soaking

1. Pour soaking agent/detergent into

compartment II in accordance with
the manufacturer's instructions.

2. Turn the programme selector to

Cottons 30 °C programme.

3. Press Start/Reload.

4. After approx. ten minutes, press

Start/Reload .

5. After the required soaking time,

press Start/Reload again to
continue or change the programme.

Notes

■ Load laundry of the same colour.

■ No additional detergent is required;

the soaking solution is used for
washing.

ευπαθή (Delicates)
For delicate, washable fabrics, e.g. made of silk, satin, synthetic

fibres or blended fabrics (e.g. silk blouses, silk scarves)

Note: Use a detergent which is suitable for machine washing deli-

cates or silk.

Max. 2 kg

30 °C

– – – ... 800 rpm
G, 2

ανάμεικτα(Mix)
A mixed load of fabrics made of cotton and synthetic fabrics

Max. 3.5 kg

40 °C

– – – ... 1000** rpm

V, 2

γρήγορο 15’/30’ (Super/Quick 15’/30’)
Extra-short programme of approx. 15/30 minutes, suitable for small

items of lightly soiled laundry

Max. 2 kg/3.5 kg

30 °C

– – – ... 1000 rpm

-

συνθετικά (Easy-Care)
Fabrics made from synthetic or blended fabrics

Max. 4 kg

30 °C, 40 °C

– – – ... 1000 rpm

V, 2

Note: For programmes with pre-wash, divide the detergent between compartments I and II.

Programme/type of laundry/information Settings

Programme default settings en

13

0 Programme default

settings

Programme default settings

The temperature, spin speed and
programme duration ("Ready in" time)
for all programmes are preset at the
factory.

These are displayed in the display panel
after selecting the programme.

You can change the default settings as
follows.

Spin speed 0

Depending on the programme
progress, you can change the spin
speed (in rpm; rotations per minute)
before and during the programme.

To do this, repeatedly select the
corresponding button until the required
setting is displayed.

Setting – – – 0 : Rinse hold = without
final spin, the laundry remains in the
water after the final rinse.

You can select "Rinse hold" to prevent
creasing if the laundry will not be taken
out of the washing machine immediately
after the programme has ended.

The maximum speed that can be set
depends on the model and programme
that have been selected.

Overview of programmes ~ Page 11

"Ready in"

When you select the programme, the
relevant programme duration is
displayed.

The programme duration is
automatically adjusted when the
programme is running. Changes to the
programme default settings or
programme settings also change the
programme duration.

Before starting the programme, the
programme end ("Ready in" time) can
be pre-selected in increments of one
hour (h = hours) up to a maximum of 24
hours.

To do this, repeatedly select the
corresponding button until the required
setting is displayed.

Note: The programme duration is

included in the selected "Ready in" time.

After the start, the pre-selected time,
e.g. 8 h, is displayed and the time
counts down to the start of the wash
programme. The programme duration is
then displayed, e.g. 2:30
(hours:minutes).

Changing the pre-selected time:

You can change the pre-selected time
after the start of the programme as
follows:

1. Press Start/Reload.

2. Press the "Ready in" button

repeatedly until the required number
of hours is displayed.

3. Press the Start/Reload button.

Adding laundry while the pre-selected
time continues running:

1. Press Start/Reload.

2. The symbols YES and Ä light up on

the display panel. The washing
machine door can be opened and
laundry can be added.

3. Close the washing machine door.

4. Press the Start/Reload button. The

pre-selected time continues to run.

en Additional programme settings

14

\ Additional programme

settings

Additional programme settings

V SpeedPerfect

For washing in a shorter time with a
washing result comparable to that of the
standard programme.

Note: Do not exceed the maximum

load.
Overview of programmes ~ Page 11

2 Pre-wash

Additional Pre-wash (at 30°C).

1 Operating the

appliance

Operating the appliance

Preparing the washing
machine

Note: The washing machine must be

correctly installed and connected.

From ~ Page 28

1. Connect the mains plug.

2. Turn on the water tap.

3. Open the door.

4. Check that the drum is completely

drained. Drain if necessary.

Select programme/switch on
the appliance

Note: If you have activated the

childproof lock, you must first deactivate
it before you can set a programme.

~ Page 16

Use the programme selector to select
the required programme. Can be turned
in either direction.

The machine is switched on.

The display panel shows the following
information consecutively for the
selected programme:

■ The programme duration,

■ The preset spin speed and

■ The maximum load.

Change the programme
default settings

You can use the default settings or
change them.

To do this, repeatedly select the
corresponding button until the required
setting is displayed.

The settings are activated without
needing to be confirmed.

They are not saved when the appliance
is switched off.

Programme default settings ~ Page 13
Overview of programmes from

~ Page 11

Select additional programme
settings

By selecting additional settings, you can
better adapt the washing process to
your items of laundry.

The settings can be selected or
deselected depending on the
programme progress.

Operating the appliance en

15

The indicator lamp for the button lights
up if a setting is active.

The settings are not saved when the
appliance is switched off.

Additional settings ~ Page 14
Overview of programmes from

~ Page 11

Placing laundry into the drum

:Warning

Danger of death!

Items of laundry pretreated with
cleaning agents that contain solvents,
e.g. stain remover/cleaning solvent,
may cause an explosion after being
loaded into the washing machine.
Hand-rinse items of laundry thoroughly
beforehand.

Notes

■ Mix items of laundry of varying sizes.

Laundry items of different sizes
distribute themselves better during
the spin cycle. Individual items of
laundry may lead to imbalances.

■ Observe the specified maximum

load. Overfilling has a negative
impact on the washing result and
promotes creasing.

1. Place presorted items of laundry

unfolded in the washing drum.

2. Make sure that no items of laundry

are trapped between the washing
machine door and the rubber seal,
and close the door.

The Start button indicator lamp flashes
and the programme settings continue to
be displayed on the display panel one

after another. It is possible to change
the settings.

Measure and add detergent
and care products

Caution!
Damage to the appliance

Cleaning agents and agents for
pretreating laundry (e.g. stain removers,
prewash sprays, etc.) may cause
damage if they come into contact with
the surfaces of the washing machine.
Do not allow these agents to come into
contact with the surfaces of the washing
machine. If necessary, immediately wipe
away spray residue and other residues/
droplets with a damp cloth.

Measuring

Measure the detergent and care
products according to:

■ Water hardness; ask your water

supply company

■ The manufacturer's instructions on

the packaging

■ The amount of laundry

■ Soiling ~ Page 10

Filling

:Warning

Eye/skin irritation!

Detergent and care products may spray
out if the detergent drawer is opened
while the machine is in operation.
Open the drawer carefully.
Rinse eyes or skin thoroughly if they
come into contact with detergent/care
products.
If swallowed accidentally, seek medical
advice.

Note: Dilute viscous fabric softener and

fabric conditioner with water; this
prevents blockages.

Pour the detergent and care products
into the appropriate compartments:

en Operating the appliance

16

1. Pull out the detergent drawer as far

as possible.

2. Add detergent and/or care products.

3. Close the detergent drawer.

Measuring aid* for liquid detergent

*depending on the model

Position the measuring aid for
measuring the correct amount of liquid
detergent:

1. Pull out the detergent drawer. Press

down the insert and fully remove the
drawer.

2. Slide the measuring aid forwards,

fold it down and click it into place.

3. Reinsert the drawer.

Note: Do not use the measuring aid for

gel detergents and washing powder, or
for programmes with prewash or when
"Ready in" time is selected.

For models without a measuring aid,
pour the liquid detergent into the

appropriate dispenser and place it in
the drum.

Start the programme

Select the Start/Pause A button. The
indicator lamp lights up and the
programme starts.

During the programme, the display
panel shows the "Ready in" time or,
after starting the wash programme, the
programme duration and the symbols
for the programme progress.

~ Page 8

Note: If you want to lock the

programme to prevent it from being
inadvertently adjusted, you can select
the childproof lock as follows.

Childproof lock

You can lock the washing machine to
prevent the functions you have set from
being changed inadvertently. To do this,
activate the childproof lock after starting
the programme.

To activate/deactivate the childproof
lock, press and hold Start/Reload for
approx. five seconds. The @ symbol
appears in the display panel.

■ @ lights up: The childproof lock is

active.

■ @ flashes: The childproof lock is

active and the programme selector
was adjusted. To prevent the
programme from stopping, turn the
programme selector back to the
original programme. The symbol
lights up again.

Note: The childproof lock can remain

activated until you wish to start the next
programme, even after switching off the
machine.
You must then deactivate the childproof
lock before starting the programme and
activate it again as necessary once the
programme has started.

Measuring aid A For liquid detergent

Compartment II Detergent for the main wash,

water softener, bleach, stain
remover

Compartment i Fabric softener, starch

Do not exceed the max.

Compartment I Detergent for prewash

Operating the appliance en

17

Adding laundry

After starting the programme, you can
add or remove laundry as required.

To do this, press the Start/Reload
button.

The Start/Reload indicator lamp flashes
and the machine checks whether it is
possible to add laundry.

Note: Do not leave the washing

machine door open for too long when
adding laundry as water from the
laundry may leak out.

If the display panel shows:

■ Both YES and Ä symbols lit up, it is

possible to add laundry.

■ A flashing NO symbol, wait until YES

and Ä symbols light up.
Do not open the door until both YES
and Ä symbols are lit.

■ A flashing NO symbol, it is not

possible to add laundry.
For safety reasons, the washing
machine door remains locked when
the water level or temperature is
high, or while the drum is rotating,
and it is not possible to add laundry.

To continue the programme, press
the Start/Reload button. The

programme continues automatically.

Changing the programme

If you have started the wrong
programme by mistake, you can
change the programme as follows:

1. Press Start/Reload.

2. Select the other programme.

3. Press Start/Reload . The new

programme starts from the
beginning.

Cancel the programme

Programmes at high temperatures:

1. Press Start/Reload.

2. To cool the laundry: Select Rinse.

3. Press Start/Reload .

For programmes at low temperatures:

1. Press Start/Reload.

2. Select Spin or Drain.

3. Press Start/Reload.

Programme end during rinse
hold

– – – 0 appears on the display panel
and the Start/Reload button indicator
lamp flashes.

To end the programme, set the
programme selector to Spin/Drain or
select a spin speed. Then press the

Start/Reload button.

Programme end

End appears on the display panel and

the Start/Reload button indicator lamp
is off.

If the r symbol appears on the display
panel, the washing machine has
detected too much foam during the
wash programme and automatically
switched on a rinse cycle to remove the
foam.

Note: Add less detergent for the next

washing cycle with the same load.

Removing laundry/switching
off the appliance

1. Open the washing machine door

and remove the laundry.

2. Set the programme selector to Off.

The appliance is switched off.

3. Turn off the water tap.
Note: Not required for Aqua-Stop

models.

Notes

■ Do not leave any items of laundry in

the drum. They may shrink in the
next wash or discolour another item.

en Sensors

18

■ Remove any foreign objects from the

drum and the rubber seal – risk of
rusting.

■ Leave the washing machine door

and detergent drawer open so that
any residual water can dry away.

■ Always wait for the end of the

programme, otherwise the appliance
may still be locked. Then switch on
the appliance and wait for it to
unlock.

■ If the display panel goes off at the

end of a programme, energy-saving
mode is active. To activate the panel,
press any button.

H Sensors

Sensors

Automatic load sensing

The automatic load sensing function
adapts the water consumption ideally to
each programme depending on the
type of fabric and the load.

Unbalanced load detection
system

The automatic unbalanced load
detection system detects imbalances
and ensures even distribution of the
laundry by repeatedly starting and
stopping drum spinning.

If the laundry is extremely unevenly
distributed, the speed is reduced or the
spin cycle is not performed for safety
reasons.

Note: Place large and small items of

laundry evenly in the drum. ~ Page 23

Setting the signal en

19

M Setting the signal

Setting the signal

1. Activate the setting mode for the signal volume

Set to stop. Press and hold the Spin speed button +

and turn the dial one position to the right.

Press and hold the button for approx.
five seconds until the display elements
light up. Setting mode is activated.

2. Set the volume for the button signals (depending on the model)

Press the button repeatedly until the desired
volume is reached.

Go to point
3 or

Set to stop to exit the setting mode for the
signal volume.

3. Set the volume for the information signals

Turn the dial one position
to the right.

Press the button repeatedly
until the desired volume is
reached.

Set to stop to exit the setting mode for the sig­nal volume.

en Cleaning and maintenance

20

2 Cleaning and

maintenance

Cleaning and maintenance

:Warning

Danger of death!

There is a risk of electric shock if you
touch live components.
Switch off the appliance and unplug the
mains plug.

:Warning

Risk of poisoning!

Toxic vapours can be produced by
cleaning agents that contain solvents,
e.g. cleaning solvent.
Do not use cleaning agents that contain
solvents.

Caution!
Damage to the appliance

Cleaning agents that contain solvents,
e.g. cleaning solvent, can damage
surfaces and components in the
machine.
Do not use cleaning agents that contain
solvents.

Machine housing/control
panel

■ Wipe the housing and the control

panel with a soft, damp cloth.

■ Remove the detergent residue

immediately.

■ Do not clean with a water jet.

Drum

Use chlorine-free cleaning agents and
not steel wool.

Descaling

Descaling should not be necessary if
the detergent is measured out correctly.
However, if it is required, follow the
manufacturer's instructions for the
descaling agent. Suitable descalers can

be obtained via our website or from our
after-sales service.

Detergent drawer and housing

If the washing machine contains
detergent or fabric softener residues:

1. Pull out the detergent drawer. Press

down the insert and fully remove the
drawer.

2. To remove the insert: Push the insert

upwards from below with your finger.

3. Clean the detergent dispenser tray

and insert with water and a brush,
and dry it. Clean the inside of the
housing as well.

4. Fit the insert and lock it in place

(push the cylinder onto the guide
pin).

5. Push in the detergent drawer.

Note: Leave the detergent drawer open

so that any residual water can
evaporate.

Detergent solution pump
blocked

:Warning

Risk of scalding!

When you wash at high temperatures,
the water gets very hot. If you come into
contact with the hot water, you may be
scalded.
Allow the water to cool down.

1. Turn off the water tap so that no

more water can flow in and has to be
drained via the drain pump.

2. Switch off the appliance. Disconnect

the mains plug.

Cleaning and maintenance en

21

3. Open and remove the service flap.

4. Take the drain hose out of the

retainer.
Remove the sealing cap, allow the
detergent solution to flow out into a
suitable container.
Replace the sealing cap and place
the drainage hose in the retainer.

5. Carefully unscrew the pump cover,

residual water may leak out.
Clean the interior, pump cover
thread and pump housing. The
impeller in the detergent solution
pump must be able to rotate.
Refit the pump cover and screw it on
tightly. The handle must be in a
vertical position.

6. Place the service flap back on, lock

it into place, and close it.

Note: To prevent unused detergent

from flowing straight into the drain
during the next wash: Pour 1 litre of
water into compartment II and start the

[ Empty programme.

The drain hose at the siphon
is blocked

1. Switch off the appliance. Disconnect

the mains plug.

2. Loosen the hose clamp. Carefully

remove the drain hose, residual
water may leak out.

3. Clean the drainage hose and siphon

connecting piece.

4. Reattach the drainage hose and

secure the connection using the
hose clamp.

Filter in the water supply
blocked

For this, first reduce the water pressure
in the supply hose:

1. Turn off the water tap.

2. Select any programme (except

Rinse//Spin/Empty).

3. Press Start. Allow the programme to

run for approximately 40 seconds.

4. Set the programme selector to Off.

Disconnect the mains plug.

5. Clean the filter on the water tap:

Remove the hose from the water tap.
Clean the filter with a small brush.

en Faults and what to do about them.

22

6. For standard and Aqua-Secure

models, clean the filter on the rear of
the appliance:
Remove the hose from the rear of
the appliance,
Remove the filter using pliers and
clean the filter.

7. Connect the hose and check for

leaks.

3 Faults and what to do

about them.

Faults and what to do about them.

Emergency release

e.g. in the event of a power cut
The programme will continue running

when the power supply has been
restored.

However, if the laundry has to be
removed, the washing machine door
can be opened as follows:

:Warning

Risk of scalding!

When you are washing at high
temperatures, there is a risk of scalding
if you come into contact with detergent
solution and laundry.
If possible, leave it to cool down.

:Warning

Risk of injury!

You may injure your hands if you reach
into the drum while it is turning.
Do not reach into the drum when it is
turning.
Wait until the drum has stopped turning.

Caution!
Water damage

Any escaping water may cause water
damage.
Do not open the washing machine door
if water can be seen through the glass.

1. Switch off the appliance. Disconnect

the mains plug.

2. Drain the detergent solution

.

3. Pull the emergency release

downwards with a tool and release.
The washing machine door can then
be opened.

Faults and what to do about them. en

23

Information on the display panel

Faults and what to do about them.

Display Cause/remedial action

YES The washing machine door is unlocked. It is possible to add laundry.

NO ■ Temperature too high. Wait until the temperature drops.

■ Water level too high. Not possible to add laundry. Close the washing machine

door immediately, if open. Select Start/Reload to continue the programme.

Ä flashes ■ Laundry may be caught. Please open and close the washing machine door

again and select Start/Reload.

■ If necessary, push the washing machine door closed or remove the laundry and

push it closed again.

■ If necessary, switch the appliance off and on again; set the programme and

make your individual settings; start the programme.

E:17 ■ Turn the water tap on fully,

■ supply hose kinked or trapped,

■ water pressure too low. Clean the filter. ~ Page 21

E:18 ■ Detergent solution pump blocked. Clean detergent solution pump.

~ Page 20

■ The drain hose/waste pipe is blocked. Clean the drain hose on the siphon.

~ Page 21

E:23 Water in the base tub, appliance leaking. Turn off the water tap. Call the after-sales

service.

@ Childproof lock activated; deactivate it. ~ Page 16

r flashes Too much foam detected, a rinse cycle has been switched on. ~ Page 17

Other displays Switch off the appliance, wait for 5 seconds and switch it back on again. If the dis-

play appears again, call the after-sales service. ~ Page 25

Faults Cause/remedial action

Water is leaking out. ■ Attach/replace the drainage hose correctly.

■ Tighten the screw connection of the supply hose.

No water supply.
Detergent not dispensed.

■ Start/Reload not selected?

■ Tap not turned on?

■ Filter blocked? Clean the filter. ~ Page 21

■ Supply hose kinked or trapped?

Washing machine door
cannot be opened.

■ Safety function active. Programme stopped?

■ – – – 0 (Rinse hold = without final spin) selected?

■ Can be opened by emergency release only? ~ Page 22

Programme does not
start.

■ Start/Reload or "Ready in" time selected?

■ Washing machine door closed?

■ @ Childproof lock activated? Deactivate it. ~ Page 16

en Faults and what to do about them.

24

Detergent solution is not
emptied.

■ – – – 0 (Rinse hold = without final spin) selected?

■ Clean detergent solution pump. ~ Page 20

■ Clean the waste pipe and/or drainage hose.

Water not visible in the
drum.

Not a fault – water below the visible area.

Spin result not satisfac­tory.

Laundry wet/too damp.

■ Not a fault – the unbalanced load detection system has interrupted the spin

because the laundry is unevenly distributed.
Distribute small and large items of laundry evenly in the drum.

■ Easy-Iron selected (depending on model)?

■ Speed selected too low?

Spin cycle started and
stopped several times.

Not a fault – the unbalanced-load detection system is adjusting the imbalance.

The programme duration
is longer than usual.

■ Not a fault – the unbalanced-load detection system is adjusting the imbal-

ance by repeatedly distributing the laundry.

■ Not a fault – the foam detection system active – adds an additional rinse

cycle.

The programme duration
changes during the wash
cycle.

Not a fault – the programme sequence is optimised for the particular washing
process. This may lead to changes in the programme duration in the display
panel.

Residual water in the
compartment i for care
products.

■ Not a fault – the effect of the care product is not affected.

■ Clean the insert if necessary.

Odours in the washing
machine.

Run the Cottons 90 °C programme without laundry.
Use standard detergent.

The r symbol flashes in
the display panel. Foam
may escape from the
detergent drawer.

Too much detergent used?
Mix one tablespoon of fabric softener with 1/2 litre water and pour into com-

partment II (not for outdoor fabrics, sportswear fabrics or those made with
down).

Reduce the detergent dosage for the next wash cycle.

Intense noise, vibrations
and "wandering" during
spinning.

■ Is the appliance levelled? Level the appliance. ~ Page 32

■ Are the appliance feet fixed? Secure the appliance feet. ~ Page 32

■ Transport locks removed? Remove the transport locks. ~ Page 29

Display panel/indicator
lamps do not function dur­ing operation.

■ Power cut?

■ Circuit breakers tripped? Switch the circuit breakers back on or replace

them.

■ If the fault occurs repeatedly, call the after-sales service.

Detergent residues on the
laundry.

■ Occasionally, phosphate-free detergents contain water-insoluble residues.

■ Select Rinse or brush the laundry after washing.

NO appears on the
display in reload mode.

■ Water level too high. Not possible to add laundry. Close the washing

machine door immediately, if necessary.

■ Select Start/Reload to continue the programme.

Faults Cause/remedial action

After-sales service en

25

4 After-sales service

After-sales service

If you cannot correct the fault yourself,
(see section, Faults and what to do
about them) ~ Page 22, please
contact our after-sales service. ~
Cover page

We will always find an appropriate
solution in order to avoid unnecessary
visits by engineers.

Please give the after-sales service the
product number (E no.) and the
production number (FD) of the
appliance.

You can find this information,
*depending on the model:

On the inside of the washing machine
door*/in the opened service flap* and
on the rear of the appliance.

Trust the expertise of the
manufacturer.

Contact us for assistance. By doing so,
you will ensure that the repairs are
carried out by trained service personnel
using genuine spare parts.

YES appears on the dis­play in reload mode.

The washing machine door is unlocked. It is possible to add laundry.

If you cannot correct a fault yourself (after switching off/on) or a repair is required:

■ Turn the programme selector to Off. The appliance is switched off.

■ Unplug the mains plug from the socket.

■ Turn off the tap and call the after-sales service.

Faults Cause/remedial action

Product number Production number

(1U )'

en Consumption rates

26

[ Consumption rates

Consumption rates

Energy and water consumption, programme duration and
residual moisture for the main washing programmes

(approximate values)

Efficiency test programmes for cotton fabrics

The following programmes (standard
programmes, indicated by ü) are
suitable for cleaning normally soiled
cotton fabrics and are the most efficient
with respect to combined energy and
water consumption.

Programme Load Energy consumption* Water* Programme duration*

Cotton 20 °C 8 kg 0,40 kWh 71 l 2 3/4 h

Cotton 40 °C 8 kg 1,10 kWh 71 l 2 3/4 h

Cotton 60 °C 8 kg 1,51 kWh 71 l 2 3/4 h

Cottons90 °C 8 kg 2,39 kWh 82 l 2 3/4 h

Easy-Care 40 °C 4 kg 0,79 kWh 53 l 2 h

Mixed Fabrics 40 °C 3,5 kg 0,51 kWh 45 l 1 1/4 h

Delicates/Silk 30 °C 2 kg 0,21 kWh 36 l 3/4 h

Wool 30 °C 2 kg 0,22 kWh 42 l 3/4 h

Programme Approximate information on the residual moisture**

WAK28 ... WAK24 ... WAK20 ...

WM14K ... WM12K ... WM10K ...

3TS ... 3TS ... 3TS ...

max 1400 rpm max 1200 rpm max 1000 rpm

Cottons 48 % 53 % 62 %

Easy-Care 40 % 40 % 40 %

Delicate/Silk 30 % 30 % 30 %

Wool 45 % 45 % 45 %

* The values may deviate from the stated values depending on the following factors: water pressure and

hardness; water inlet temperature; ambient temperature; type, amount and soiling of laundry; type of
detergent used; fluctuations in the power supply and additional functions selected.

** Information on residual moisture based on programme-dependent spin speed limits and maximum

loads.

Technical data en

27

J Technical data

Technical data

Dimensions:
850 x 600 x 590 mm

(Height x width x depth)
Weight

63-83 kg (depending on model)
Mains connection:

Mains voltage 220-240 V, 50 Hz
Nominal current 10 A
Nominal output 2300 W
Water pressure:

100-1000 kPa (1-10 bar)

Power consumption when switched
off:

0.12 W

Power consumption when ready for
use (left-on mode):

1.49 W

Standard-Programs for Cotton under EU-Regulation 1015/
2010

Load Programme du-

ration

Programme Cottons ú 8 kg 3 _ h
Programme Cottons ú 4 kg 3 _ h
Programme Cottons û 4 kg 3 ] h

Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU with
cold water (15 °C).
The programme temperature information is based on the temperature stated on the care label for
the fabrics. The actual washing temperature may deviate from the stated programme temperature
for energy-saving reasons.

en Positioning and connecting

28

5 Positioning and

connecting

Positioning and connecting

Included with the appliance

Note: Check the machine for transport

damage. Never use a damaged
machine. If you have a complaint,
please contact the retailer from whom
you purchased the appliance, or our
after-sales service.

In addition, a hose clamp ( 24 - 40 mm
diameter, available from specialist
dealers) is required to connect the
water drain hose to a siphon.

Useful tools

■ Spirit level for levelling

■ Wrench with:

– WAF 13 for loosening the

transport locks, and

– WAF 17 for aligning the

appliance feet

Safety instructions

:Warning

Risk of injury!

■ The washing machine is very heavy.

Be careful when lifting/transporting
the washing machine.

■ When the washing machine is lifted

by its protruding parts (e.g. the
washing machine door), the
components may break off and
cause injuries.
Do not lift the washing machine by
protruding parts.

■ If the hose and mains cables are not

routed properly, there is a risk of
tripping and injury.
Lay hoses and cables in such a way
that there is no risk of tripping.

Caution!
Damage to the appliance

Frozen hoses may rip/burst.
Do not install the washing machine in
areas exposed to frost or outdoors.

Caution!
Water damage

The connection points for the water
supply hose and water drain hose are
under high water pressure. To prevent

( Mains cable
0 Bag:

■ Installation and operating instructions

■ After-sales service location directory*

■ Warranty*

■ Cover caps for openings left after

removing the transport locks

■ Wrench*

8 Water supply hose on Aqua-Stop models
@ Water drain hose
H Elbow for securing the water drain hose*



#



3

+



P Water supply hose on standard/Aqua-

Secure models

*depending on the model

Positioning and connecting en

29

leaks and water damage, you must
follow the instructions in this section.

Notes

■ In addition to the safety information

listed here, the local water and
electricity supplier may have special
requirements.

■ If in doubt, have the appliance

connected by a specialist.

Installation surface

Note: The washing machine be stable

so that it does not move around.

■ The installation surface must be firm

and level.

■ Soft floors/floor coverings are not

suitable.

Installation on a base or a
wooden joist floor

Caution!
Damage to the appliance

The washing machine may "wander"
and tip/topple from the base when
spinning.
The feet of the appliance must be
secured with holding brackets.
Order no. WMZ 2200, WX 9756,
CZ 110600, Z 7080X0

Note: On wooden joist floors, install the

washing machine:

■ In a corner, if possible,

■ On a water-resistant wooden board

(min. 30 mm thick) which is screwed
tightly to the floor.

Installing the appliance in a
kitchenette

:Warning

Danger of death!

There is a risk of electric shock if you
touch live components.

Do not remove the appliance covering
plate.

Notes

■ Recess width of 60 cm required.

■ Only install the washing machine

underneath a continuous worktop
that is securely connected to
adjacent cabinets.

Removing the transport locks

Caution!
Damage to the appliance

■ The machine is secured for

transportation using transport locks.
If the transport locks are not
removed, the drum, for example,
may become damaged when the
machine is operated.
Before using the appliance for the
first time, make sure that you
completely remove all four transport
locks. Keep the locks in a safe
place.

■ To prevent transport damage from

occurring if the appliance is moved
at a later date, you must refit the
transport locks before transporting
the appliance.

Note: Keep the screws and sleeves in

a safe place.

1. Take the hoses out of the holders.

en Positioning and connecting

30

2. Unscrew and remove all four

transport brace screws.
Remove the sleeves. To do this,
remove the mains cable from the
holders.

3. Fit the covers. Lock the covers firmly

in place by applying pressure to the
snap-in hooks.

Hose and cable lengths

■ Left-hand connection

■ Right-hand connection

Tip: The following are available from

specialist dealers/the after-sales
service:

■ An extension for Aqua-Stop or cold

water supply hose (approx. 2.50 m);
order no. WMZ2380, WZ10130,
CZ11350, Z7070X0

■ A longer supply hose (approx.

2.20 m) for standard model

Water inlet

:Warning

Danger of death!

There is a risk of electric shock if you
touch live components.
Do not immerse the Aqua-Stop safety
valve in water (it contains an electric
valve).

Observe the following when connecting
the machine:

Notes

■ Only operate the washing machine

using cold mains water.

■ Do not connect the machine to the

mixer tap of an unpressurised hot­water boiler.

■ Do not use a used supply hose. Only

use the supply hose supplied or one
that was purchased from an
authorised specialist retailer.

■ Do not bend, squash, modify or cut

through the water supply hose
(otherwise its strength is no longer
guaranteed).

PD[FP

aFP

aFP

aFP

aFP

PD[FP

aFP

aFP

Positioning and connecting en

31

■ Only tighten the screw connections

by hand. If the screw connections
are tightened too much with a tool
(pliers), the thread may be
damaged.

Optimum water pressure in the supply
network

At least 100 kPa (1 bar)
Maximum 1000 kPa (10 bar)

When the tap is open, the water flow is
at least 8 l/min.

If the water pressure is higher than this,
a pressure-reducing valve must be
installed.

Connection

Connect the water supply hose to the
water tap (¾" = 26.4 mm) and to the
appliance (not necessary for Aqua-Stop
models as this is permanently installed):

■ Model: Standard

■ Model: AquaSecure

■ Model: Aqua-Stop

Note: Open the water tap carefully,

checking the leak tightness of the
connection points. The screw
connection is under mains water
pressure.

Water outlet

Caution!
Water damage

If the drain hose slips out of the wash
basin or the connection point during
draining due to high water pressure, any
escaping water may cause water
damage.
Secure the drain hose so that it cannot
slip out.

Note: Do not kink the water drain hose

or put strain on it lengthways.

You can lay the water drain hose as
follows:

■ Outlet in a sink

:Warning

Risk of scalding!

When you are washing at high
temperatures, there is a risk of
scalding if you come into contact
with hot detergent solution e.g. if hot
detergent solution is being drained
into a wash basin.
Do not reach into the hot detergent
solution.

Caution!

Damage to the appliance/fabrics

If the end of the drain hose is
immersed in the drained water, water
may be sucked back into the
appliance and may damage the
appliance/fabrics.
Make sure that:
– The plug does not block drainage

from the sink.

– The end of the drain hose is not

immersed in the drained water.

– The water drains away quickly

enough.

en Positioning and connecting

32

■ Drainage into a siphon

The connection point must be
secured using a hose clamp with a
diameter of 24-40 mm (available
from specialist dealers).

■ Outlet into a plastic pipe with

rubber bushing or into a drainage
pit

Levelling

Level the appliance using a spirit level.
Incorrect levelling may result in intense

noise, vibrations and "wandering".

1. Loosen the lock nuts using a

wrench, by turning it in a clockwise
direction.

2. Check the alignment of the washing

machine with a spirit level, and
adjust it if necessary. Change the
height by turning the appliance feet.
All four appliance feet must stand
firmly on the ground.

3. Tighten the lock nut against the

housing.

In doing so, hold the foot tight and
do not adjust its height.
The lock nuts on all four appliance
feet must be screwed tightly against
the housing.

Electrical connection

:Warning

Danger of death!

There is a risk of electric shock if you
touch live components.

■ Never touch or hold the mains plug

with wet hands.

■ Only pull out the mains cable by the

plug and never by the cable, as this
could damage it.

■ Never unplug the mains plug during

operation.

Observe the following information and
ensure that:

Notes

■ The mains voltage and voltage

indicated on the washing machine
(rating plate) are the same.
The connected load and fuse
required are specified on the rating
plate.

■ The washing machine is only

connected to an alternating current
via a properly installed earthed
socket.

■ The mains plug fits the socket.

■ The cable cross-section is adequate.

■ The earthing system is properly

installed.

Positioning and connecting en

33

■ The mains cable is only replaced by

a qualified electrician (if this is
necessary). Replacement mains
cables are available from the after­sales service.

■ No multiple plugs/couplings or

extension cables are used.

■ If an earth-leakage circuit breaker is

used, only a type which displays this
symbol is used: z.
Only this symbol guarantees
compliance with the currently
applicable regulations.

■ The mains plug can be accessed at

all times.

■ The mains cable is not bent,

squashed, modified, cut through, or
in contact with heat sources.

Before washing for the first
time

The washing machine was thoroughly
tested before leaving the factory. In
order to remove any water which may
be left over from the test, run the first
washing cycle without any laundry.

Notes

■ The washing machine must be

correctly installed and connected.

From ~ Page 28

■ Never use a damaged machine.

Inform your after-sales service.

1. Check the machine.

2. Remove the protective film from the

control panel.

3. Connect the mains plug.

4. Turn on the water tap.

5. Close the washing machine door (do

not load any laundry).

6. Select thei Cottons programme

and set the temperature to 90 °C.

7. Open the detergent drawer.

8. Pour approx. 1 litre of water into

compartment II.

9. Pour standard detergent into

compartment II.

Note: To prevent foaming, only use

half of the amount of detergent
recommended by the detergent
manufacturer. Do not use detergent
for wool or delicates.

10.Close the detergent drawer.

11.Press Start.

12.Switch off the appliance at the end of

the programme.

Your washing machine is now ready to
use.

Transportation

e.g. when moving home

Preparatory work:

1. Turn off the water tap.

2. Reduce the water pressure in the

supply hose.
Maintenance – filter in the water
supply ~ Page 21

3. Drain the remaining detergent

solution.
Maintenance – detergent solution
pump blocked ~ Page 20

4. Disconnect the washing machine

from the mains.

5. Remove the hoses.

Installing the transport locks:

1. Remove the covers and keep them

in a safe place.
Use a screwdriver if necessary.

2. Insert all four sleeves.

Clip the mains cable securely in the
holders. Insert and tighten the
screws.

en Positioning and connecting

34

Before initial use:

Notes

■ The transport locks must be

removed.

■ To prevent unused detergent from

flowing straight into the drain during
the next wash: Pour approximately 1
litre of water into compartment II and
select and start the [ Empty
programme.

*9000998136*

9000998136 (9504)