Installation Instructions
V1.0
PISL2
Thank you for choosing our product! We strive to provide the best
quality and services for our customers. Would you kindly share your
experience on Amazon if you are satisfied? Should you have any
issues, please don't hesitate to contact us.
Telephone：800-556-9829 Mon-Fri 10am - 6pm (PST) (USA) (CAN)
Email：supportus@pipishell.net (US/CA/DE/UK/FR/IT/ES/JP/AU)
IMPORTANT SAFETY INFORMATION
•Check package contents against Supplied Parts and Hardware Lists to assure that all
components were received undamaged. Do not use damaged or defective parts.lf you
require replacement parts, contact customer service at supportus@pipishell.net
•Not all parts and hardware included will be used.
•Carefully read all instructions before attempting installation.If you do not understand
the instructions or have any concerns or questions, please contact customer service at
supportus@pipishell.net
•This product may contain moving parts. Use with caution.
•Do not use this product for any purpose or in any configuration not explicitly specified
in this instruction. We hereby disclaim any liability for injury or damage arising from
incorrect assembly, incorrect mounting, or incorrect use of this product.
•DO NOT INSTALL INTO DRYWALL ALONE.
Tools Needed (Not lncluded)
Stud Finder
Wood Drill
Supplied Parts
Wall Plate
Tape measure
Concrete Drill
01
Pencil
socket wrench
x1
1
Drill
Screwdriver
TV Brackets
02
Hammer
level
x2
Supplied Hardware
Hardware for Attaching TV Bracket to TV
03
x4
M4
M4
M6
M8
Washers
M4X16mm
M6X16mm
M8 x 25mm
x4
M6
x4
x4
x4
x4
05
M4X30mm
M6X30mm
04
TV Screws
x4
x4
x4
5mm
Spacers
x4
10mm2.5mm
Hardware for Attaching Wall Plate to Wall
Lag Bolts
M6X50
Wall Anchor
These anchors are for concrete or
brick walls ONLY. DO NOT use them in
drywall or wood studs.
x4 x4
A1
A2
2
CAUTION!
Step 1 Select TV Screws
Only one screw size fits your TV.
M6M4 M8
Step 2
a
TV Bracket
Select Spacers (If Needed)
NO SPACER
For Flat TV
Spacer not necessary
Short Screw
05
03
Washer
SPACER
b
TV Bracket
EXTRA
SPACE
For Flat TV with:
Inset Holes Cable Interference
3
Long Screw
05
Washer
03
Spacer
04
For Rounded TV
Too Short Too Long
3
3
Step 3
Secure the TV Brackets to Your TV
02
Step 4
For wood stud installation, follow STEP 4A
For concrete installation, follow STEP 4B
Step
Attach Wall Plate to Wall
4A
Wood Stud Option
a
05
03
No Spacer
With Spacer
b
05
03
04
Alternate
Spacer
setups
WARNING:
● Avoid potential personal injury or property damage! DO NOT
over-tighten the lag bolts [A1]. Tighten the lag bolts [A1] only until they
are pulled firmly against the wall plate
● Ensure the wall plate is securely fastened to the
wall before continuing on to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum
1½ x 3½ in. (38 x 89 mm)
● Stud center must be verified
[01]
.
X
4
4A-1
4A-2
Use a stud finder(not
included)to locate wood
studs. Mark the edge and
center locations.
Position the wall plate at
your desired height and
line up the holes with your
stud center line. Level the
wall plate and mark the
holes.
4A-3
4A-4
A1
Drill 4 pilot holes using a 4
mm diameter drill bit. Make
sure the depth is not less
than 50mm.
Install the wall plate
[01]
bolts [A1] . Tighten the lag bolts
[A1] only until they are pulled
firmly against the wall plate.
5
50mm
ø4mm
using lag
Socket Wrench
Step
4B
Solid Concrete or Concrete Block Option
WARNING:
● Avoid potential personal injury or property damage! DO NOT
over-tighten the lag bolts [A1]. Tighten the lag bolts [A1] only until they
are pulled firmly against the wall plate [01].
Wall
●
Ensure the wall plate is securely fastened to the wall
before continuing on to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
[01]
● Mount the wall plate
directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
4B-1 4B-2
Anchor
A2
Position the wall plate at your
desired height, level the wall plate
and mark the pilot hole locations.
Drill 4 pilot holes using a 10mm
diameter drill bit. Make sure the
depth is not less than 60mm. Never
drill into the mortar between blocks.
60mm
6
ø10mm
4B-3
Use the hammer to
knock anchors [A2]
into the wall.
Install wall plate using lag bolts [A1] and anchors [A2]. Be
sure the anchors [A2] are seated flush with the concrete
surface. Tighten the lag bolts [A1] only until they are pulled
firmly against the wall plate. DO NOT over-tighten the lag
bolts [A1].
A2
A1
Step 5
Iocking
Hang the TV onto the Wall Plate
Wall
TV
7
Loading...