Floor Polisher
PE225FP
Operator’s Manual
1
FOR YOUR SAFETY
DO NOT store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
Record This Important Information
Date of Purchase
Purchased From
Address
City State Zip
Phone Contact
Machine Model
Machine Serial Number
Important Phone Numbers
Medical Emergency
Police
Fire Department
WARNING!: The Products sold with this Manual contain or may contain chemicals that
are known to certain governments (such as the State of California, as identied in its
Proposition 65 Regulatory Warning Law) to cause cancer, birth defects or other reproductive harm.
In certain locations (including the State of California) purchasers of these Products that place them
in service at an employment job site or a publicly accessible space are required by regulation
to make certain notices, warnings or disclosures regarding the chemicals that are or may be
contained in the Products at or about such work sites. It is the purchaser’s responsibility to know
the content of, and to comply with, any laws and regulations relating to the use of these Products
in such environments. The Manufacturer disclaims any responsibility to advise purchasers of any
specic requirements that may be applicable to the use of the Products in such environments.
2
Table of Contents
Safety Precautions..............................................................4
Technical Specifications......................................................5
Operator Responsibility.......................................................6
Machine Preparation...........................................................6
Unpacking the Machine..........................................6
Transporting the Machine.......................................6
Grounding Instructions..........................................7
Extension Cords.....................................................7
Machine Components.........................................................9
Operator Handle Grips.........................................10
Switch Levers....................................................... 10
Switch Lever Safety Lock.................................. 10
Water Tank......................................................... 10
Handle Release Lever......................................... 10
Cord Hook............................................................ 10
Water Release Handle........................................ 10
Power Cord.......................................................... 10
How to Operate the Machine.............................................11
Installing the Pad Driver........................................11
Operation..................................................11
After Use...............................................................11
Scheduled Maintenance...................................................12
Machine Troubleshooting..................................................12
Parts Manual & Warranty...................................................13
Electrical Schematic.............................................14
Main Assembly....................................................16
Handle Assembly................................................20
Motor Assembly....................................................24
Gearbox Assembly...............................................25
2-Speed Motor Assembly....................................26
Manufacturer’s Warranty...................................................27
***This product is intended for commercial use only***
In this Operation Manual you will find three statements that you must read and observe
to ensure safe operation of this machine.
DANGER! indicates that the possibility of severe bodily injury or death can occur if
DANGER! statements are ignored. Read and observe all DANGER! statements
included in the Operation Manual and attached to the machine.
WARNING! indicates that the possibility of bodily injury to the operator and other
people can occur if WARNING! statements are ignored. Read and observe all
WARNING! statements included in the Operation Manual and attached to the
machine.
CAUTION! indicates that the possibility of damage to the machine or other property
can occur if CAUTION! statements are ignored. Read and observe all CAUTION!
statements included in the Operation Manual and attached to the machine.
3
Safety Precautions
Anyone operating the machine should read the
following carefully and be informed of potentially
dangerous operating conditions. Operators should
be familiar with the location and use of all safety
devices on the machine. DO NOT use the machine
if it is not in proper operating condition, and report
any damage or operation faults immediately.
DANGER! Failure to read the Owner’s Manual prior to operating or
attempting any service or maintenance procedure to your machine
could result in injury to you or to other personnel; damage to the
machine or to other property could occur as well. You must have
training in the operation of this machine before using it. If you or
your operator(s) cannot read English, have this manual explained
fully before attempting to operate this machine.
DANGER! To reduce the risk of fire, use only commercially
available floor cleaners, strippers, and waxes intended for machine
application.
DANGER! Risk of explosion. Floor sanding can result in an
explosive mixture of fine dust and air. To reduce risk of explosion,
use floor sanding machine only in well ventilated area.
DANGER! Operating a machine that is not completely or fully
assembled could result in injury or property damage. DO NOT
operate this machine until it is completely assembled. Inspect the
machine carefully before operation.
DANGER! Electrocution could occur if maintenance and repairs are
performed on a unit that is not disconnected from the power source.
Disconnect the power supply before attempting any maintenance or
service. Always remove the electrical plug from the electrical outlet
before changing the brush, pad or other attachment and before
leaving the machine.
DANGER! Using a machine with a damaged power cord could result
in an electrocution. DO NOT use the machine if the power cord is
damaged. DO NOT use the electrical cord to move the machine.
WARNING! Water solutions used with this type of machine can
leave wet areas on the floor surface. These areas can cause a
dangerous condition for the operator or other persons. Always put
“CAUTION” signs near the area being cleaned.
WARNING! Modifications or alterations to this machine can lead
to personal injury or damage to the machine. DO NOT make
unauthorized modifications or alterations to this machine. Amano
Pioneer Eclipse assumes no liabilities for injury or damage resulting
from an unauthorized modification or alteration to the machine. Any
unauthorized modification or alteration to this machine voids all
warranties.
WARNING! Electrical components of this machine can “short-out” if
exposed to water or moisture. Keep the electrical components of the
machine dry. Wipe the machine down after each use. For storage,
keep the machine in a dry building.
WARNING! Always use a three-wire electrical system connected to
the electrical ground. For maximum protection against electric shock,
use a circuit that is protected by a ground fault interrupter. Consult
your electrical contractor.
WARNING! To prevent damage to the power cord, DO NOT let the
brush, pad, pad driver or wheels touch the power cord when the
machine is running. Always lift the cord over the machine. DO NOT
pull the power cord to move the machine.
WARNING! Operating a machine without observing all labels and
instructional information could result in injury or damage. Read all
machine labels before attempting to operate. Make sure all of the
labels and instructional information are attached or fastened to the
machine. Get replacement labels and decals from your authorized
distributor.
WARNING! Sanding wood or varnish produces dust that could self
ignite and could cause injury or damage. Dispose accordingly.
WARNING! Use of this machine as a step or furniture could result in
injury or damage. DO NOT use this machine as a step or furniture.
DO NOT ride on this machine.
WARNING! To avoid injury keep hands, feet and loose clothing away from all
moving parts of this machine.
WARNING! Injury to operator or bystanders could occur if an abrupt
change in floor surface texture is encountered when using this
machine. Abrupt change in floor surface texture can cause a sudden
pulling motion by this machine. This sudden pulling motion can result
in loss of control of the machine which could injure the operator or
bystanders. Avoid motions that could cause machine to cross from
a smooth floor surface to a carpeted or rough texture floor surface
Avoid motions that could allow the machine to come in contact with
low obstacles, such as floor electrical outlets, door stops or entry
molding, etc.
WARNING! Any alterations or modifications of this machine could
result in damage to the machine or injury to the operator or other
bystanders. Alterations or modifications not authorized by the
manufacturer voids any and all warranties and liabilities.
CAUTION! The machine is heavy. Get assistance before attempting
to transport or move it.
CAUTION! When draining liquids from the machine, follow all local
and federal waste disposal standards.
4
Technical Specifications:
Description 225FP17 225FP20 225FP20DS
Voltage (V) 120 120 120
Frequency (Hz) 60 60 60
Current (A) 15 15 15/15
Pad / Brush Speed 175 rpm 175 rpm 175 rpm / 300 rpm
Power 1.5 hp (1.1 kW) 1.5 hp (1.1 kW) 1.5 hp (1.1 kW)
Gearbox 3-Planet 3-Planet 3-Planet
Pad/Brush Size 17” (43 cm) 20” (51 cm) 20” (51 cm)
Cord 14/3 Yellow SOOW 14/3 Yellow SOOW 14/3 Yellow SOOW
Cord Length 50’ (15 m) 50’ (15 m) 50’ (15 m)
Height w/ Handle 46” (117 cm) 46” (117 cm) 46” (117 cm)
Width 16.5” (42 cm) 19.5” (50 cm) 19.5” (50 cm)
Length 23” (59 cm) 24.5” (62 cm) 24.5” (62 cm)
Weight w/ cord 91 lbs (41 kg) 95 lbs (43 kg) 95 lbs (43 kg)
Handle Tube Tubular Steel Tubular Steel Tubular Steel
Main Frame Die Cast Aluminum Die Cast Aluminum Die Cast Aluminum
Tank Capacity (Optional) 2.50 gal (9.5 L) 2.50 gal (9.5 L) 2.50 gal (9.5 L)
Description 225FP17EB 225FP20EB 225FP17E 225FP20E
Voltage (V) 127 127 230 230
Frequency (Hz) 60 60 50 50
Current (A) 15 15 8 8
Pad / Brush Speed 175 rpm 175 rpm 175 rpm 175 rpm
Power 1.5 hp (1.1 kW) 1.5 hp (1.1 kW) 1.5 hp (1.1 kW) 1.5 hp (1.1 kW)
Gearbox 3-Planet 3-Planet 3-Planet 3-Planet
Pad/Brush Size 17” (43 cm) 20” (51 cm) 17” (43 cm) 20” (51 cm)
Cord H05VV 2.5mm
Cord Length 40’ (12 m) 40’ (12 m) 40’ (12 m) 40’ (12 m)
2
H05VV 2.5mm
2
HO5VVF3G1.5mm HO5VVF3G1.5mm
Height w/ Handle 46” (117 cm) 46” (117 cm) 46” (117 cm) 46” (117 cm)
Width 16.5” (42 cm) 19.5” (50 cm) 16.5” (42 cm) 19.5” (50 cm)
Length 23” (59 cm) 24.5” (62 cm) 23” (59 cm) 24.5” (62 cm)
Weight w/ cord 91 lbs (41 kg) 95 lbs (43 kg) 91 lbs (41 kg) 95 lbs (43 kg)
Handle Tube Tubular Steel Tubular Steel Tubular Steel Tubular Steel
Main Frame Die Cast Aluminum Die Cast Aluminum Die Cast Aluminum Die Cast Aluminum
5
Technical Specifications:
Description 225FP17E6 225FP20E6
Voltage (V) 230 230
Frequency (Hz) 60 60
Current (A) 8 8
Pad / Brush Speed 175 rpm 175 rpm
Power 1.5 hp (1.1 kW) 1.5 hp (1.1 kW)
Gearbox 3-Planet 3-Planet
Pad/Brush Size 17” (43 cm) 20” (51 cm)
Cord HO5VVF3G1.5mm sq HO5VVF3G1.5mm sq
Cord Length 40’ (12 m) 40’ (12 m)
Height w/ Handle 46” (117 cm) 46” (117 cm)
Width 16.5” (42 cm) 19.5” (50 cm)
Length 23” (59 cm) 24.5” (62 cm)
Weight w/ cord 91 lbs (41 kg) 95 lbs (43 kg)
Handle Tube Tubular Steel Tubular Steel
Main Frame Die Cast Aluminum Die Cast Aluminum
Tank Capacity 2.50 gal (9.5L) 2.50 gal (9.5L)
6
This Machine is Manufactured for
Commercial use only.
This machine is designed and manufactured for
indoor use on hard floor surfaces. Amano Pioneer
Eclipse Corporation (APEC) does not recommend
use of this machine in any environment other than an
indoor environment. This floor machine is designed
and manufactured for commercial floor use only. This
machine is designed to clean most modern types of
floors including composition tile, stone, marble, terrazzo,
and resilient floor covering, and some coated wood
floors.
Operator Responsibility
The operator is responsible for performing the
recommended daily maintenance and checkups of the
machine to keep it in good working condition. The
operator must inform the service mechanic or supervisor
when recommended maintenance procedures are
required as prescribed in the “MAINTENANCE” section
of this manual.
FOR SAFETY: DO NOT operate machine before
reading and understanding the operation manual.
Keep your machine regularly maintained by following the
maintenance information in this manual. Order parts and
supplies only from an Authorized Amano Pioneer Eclipse
Distributor. Use the parts illustration section of your
manual when ordering parts.
During and after operation, perform the recommended
daily and hourly procedures outlined in the Maintenance
Chart.
Figure 1
WARNING! The machine is heavy, 90 lbs (41 kg)
without the cord. To avoid injury or damage to
the machine use a firm grip and proper lifting
technique. Always use two people when lifting this
machine.
Machine Preparation
Unpacking the Machine
When the machine is delivered, carefully inspect the
shipping carton and the machine for damage. Unpack
the machine with caution. If damage is evident, save the
shipping carton so that it can be inspected. Contact the
Amano Pioneer Eclipse Customer Service Department.
Transporting the Machine
To transport the machine, follow this procedure:
1. Raise and lock the handle in the upright position. To
lock the handle, push down on the handle release
lever (See Figure 1).
2. Unplug the machine from wall outlet and wrap cord
around the handle and cork hook.
3. To pick up the machine, using two people, lift and
place in cargo area (See Figure 2).
Person #1Person #2
Figure 2
7
Grounding Instructions
120 Volt Machines
This product must be grounded while in use to protect
the operator from electrical shock. The machine is
provided with a three-conductor cord and a three contact
grounding attachment plug to the t the proper grounding
type receptacle. The green (or green and yellow)
conductor in the cord is the grounding wire. NEVER
connect this wire to other than the grounding pin of the
attachment plug. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric
current to reduce the risk of electrical shock. This
product is equipped with a cord having an equipmentgrounding conductor and grounding plug. The plug must
be inserted into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
WARNING: Improper connection of the equipmentgrounding conductor can result in a risk of electric shock.
Check with a qualied electrician or service person if
you are in doubt as to whether the outlet is properly
grounded. DO NOT modify the plug provided with the
product - if it will not t the outlet, have a proper outlet
installed by a qualied electrician.
This product is for use on a nominal 120 volt circuit
and has a grounding attachment plug that looks like
the plug illustrated as (A) in the sketch. Make sure that
the machine is connected to an outlet having the same
conguration as the plug. No adapter should be used
with this product.
WARNING: To prevent possible electric shock, protect
the machine from rain. Keep the machine in a dry
building.
WARNING: To prevent possible electric shock, always
use a 3-wire electrical system connected to the electrical
ground.
WARNING: DO NOT cut, remove or break the ground
pin. If the outlet does not t the plug, consult your
electrical contractor.
WARNING: Have worn, cut or damaged cords replaced
by an authorized service person.
Extension Cords
Use only an approved extension cord with three
conductors, a plug with three terminals, and a connector
body with three holes. The machine has a power cord
with wire size 12 AWG (AWG means American Wire
Gauge).
WARNING: If you use an extension cord, use an
extension cord with minimum wire size 12 AWG. DO
NOT use an extension cord longer than 50 feet. DO NOT
join two extension cords.
Figure 3
8
Instructions for Connection to the Power Supply (230V)
CAUTION: This machine will operate only on the AC frequency and electrical voltage shown on the nameplate.
Make sure you have the correct frequency and voltage before connecting the power cord to an outlet.
This machine must be connected to the electrical ground to protect the operator from electric shock. The machine has
a power cord with two main conductors and one earthing conductor. Connect the plug to the type of receptacle shown
in figure 5. The green and yellow conductor cord is the ground wire. Never connect this wire to any terminal other
than the ground terminal.
WARNING: Always use this machine with an AC three-conductor electrical system connected to the electrical
ground. Replace any worn, cut, or damaged cords. Peplace any damaged plugs, receptacles, or
connector bodies. Do not move the machine over an electrical cord. Always lift the cord over the
machine.
Figure 5
Extension Cords (230V)
Use only an approved extension cord with two main conductors and one earthing conductor.
WARNING: If you use an extension cord, use an extension cord with minimum wire size 1.55 mm2. Do not use
an extension cord longer than 15 meters. Do not join two extension cords.
WARNING: Do not cut, remove, or break the ground terminal. Do not try to fit a three-terminal plug into a receptacle or connector body that does not fit the plug. If the receptacle or connector body does not fit the plug, see your
Authorized person to make the connection.
9
Machine Components
Operator
Handle
Grips
Switch Lever
Safety Lock
Water Tank
Switch Levers
Cord Hook
Release
Power Cord
10
Water
Handle
Handle
Release
Lever
Operator Handle Grips
Use the operator handle grips to operate and move
the machine. The switch levers on the underside of
the handle grips, turn the motor on and off. Locate the
handle grips in a comfortable operating position and
lock the handle release lever in place. While operating
the machine, slightly raising or lowering the operators
handle will help the operator control the machine.
Switch Levers
The switch levers activate the switch module to turn the
motor on and off. The switch module will not activate
unless the switch lever safety lock is pressed first. To
operate the machine, only one switch lever has to be
engaged. This allows the operator to alternate hands
while using the machine. To stop the motor from turning,
release the switch levers.
Switch Lever Safety Lock
The switch lever safety lock is to prevent someone
from accidentally turning the machine on. To turn the
machine on, always make sure the handle is lowered in
the operators position and the handle release lever is
locked. Push and hold the switch lever safety lock with
one hand, while engaging one of the switch levers. Once
the machine has started, the switch lever safety lock can
be released.
Water Tank
The water tank can be filled with clean water. This
tank is for water only. DO NOT place any flammable,
corrosive, and/or toxic liquids and powders in the water
tank. Remove the fill cap to add water to the tank and
replace the cap to prevent splashing of water on the
electrical components during use. Always drain any
remaining water from the tank before storage.
Handle Release Lever
This handle is used to release or lock the operators
handle. Pulling up on the lever will allow the handle to
move freely. Pushing down on the lever, horizontally,
will lock the handle in place. The handle should always
be locked while in use, as well as during transport or
storage.
Cord Hook
To prevent the cord from being damaged while not is
use, wrap the cord around the cord hook and the top of
the operators handle.
Water Release Handle
Pulling up on this handle will open the valve inside the
tank and allow water to flow from the water tank to
the driver. Water will only flow from the tank while the
handle is raised. To stop the flow of water from the tank,
release the handle. The amount of flow can be varied by
how far the handle is raised.
To drain the water tank, place the machine over a drain.
Remove the fill cap and use the water release handle to
drain the tank. Replace fill cap when finished.
Power Cord
Use only the supplied power cord with this machine. The
power cord is sized to be used with this machine. To
attach the power cord to the machine, insert plug on the
back of handle into the female receptacle of the power
cord. Properly align the plug pins with the holes of the
receptacle, push together and twist to lock the cords in
place.
11
How to Operate the Machine
Installing the Pad Driver
WARNING! Drain the water from the tank before
tilting the machine back.
Place the handle in the upright (vertical) positions and
lock the handle release lever. Tilt the machine back on
the transport wheels and let the handle rest on the floor.
Align the lugs with the corresponding slots in the pad
driver and turn the pad driver counterclockwise to lock it
in place. To remove pad driver, give it a quick hard turn
clockwise.
CAUTION! Using the wrong pad, brush, or tooling
on this machine can overload the motor.
Figure 4
Lugs
Note: When the switch levers (3) are released, the
machine shuts off immediately.
5. To release water from the water tank, pull up on the
water release handle (4). The water will stop flowing
once the handle is released.
6. To change the motor speed, use the motor speed
switch (8) on the front of the operators handle (7).
After Use
1. Place the operators handle (7) in the upright (vertical)
position and unplug the power cord. Wrap the power
cord around the operator hand grips (1) and the cord
hook (6).
2. Tilt the machine back and remove the pad driver from
the machine. NEVER store the machine with the pad
driver on the machine.
3. If there is any water in the water tank, place the
machine over a drain. Using the water release handle
(8), drain the water tank.
4. Wipe the entire machine with a clean, damp cloth.
5. Inspect the entire machine and all accessories for
damage. Perform any required maintenance or
repairs before storage.
6. Store the machine in a clean, dry place with the
operator handle (7) locked in the upright position.
Slots
Operation
1. Unwrap the power cord and plug it into the properly
grounded outlet.
2. Pull up on the handle release lever (5). Move the
operator handle (7) downward until your arms are
almost straight. Push down on the handle release
lever (5) to lock it in place.
3. Lift up on the operator handle (7) until the driver if flat
against the floor.
WARNING! Be prepared to control the machine as
soon as the motor starts. Just a slight up or down
movement of the operators handle (7) will make the
machine move from side to side. Raise the handle
to go right. Lower the handle to go left.
CAUTION! Immediately start moving the machine
back and forth. Keep the machine moving while the
motor is running to avoid damage to the floor.
4. Hold one of the operator handle grips (1) firmly, push
the switch lever safety lock (2) and the compress the
switch lever (3) to start the motor.
2
5
Figure 5
7
1
3
4
2 1
6
3
12
Scheduled Maintenance
Machine Troubleshooting
13
PE225FP
Floor Polisher
Parts Manual
Notes:
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
14
Electrical Schematic - 120V
Electrical Schematic - 127V & 230V
RF068800
15
Main Assembly
24
23
15
1
11
2
3
4
10
15
12
9
5
30
15
6
8
13
32
36
34
35
33
33
3731
27
RF050600
20
25
21
22
29
19
18
14
17
2628
7
16
111814
16
Main Assembly (continued)
Item Ref. No. Description Qty
1 21075A BACK, HANDLE 1
2 10687A MODULE, INTERLOCK 1
3 21074A FRONT, HANDLE 1
4 MP499200 DECAL, PE225FP, HANDLE 1
5 80284A SCREW, #10 X 3/4” 6
6 61373A TUBE, HANDLE 1
7A MP476300 CORD, POWER, 14/3 X 50FT 1
7B 486500 CORD, POWER, TYPE I, 50FT 1
8 50781A CLAMP, HANDLE 1
9 40789A CORD, INTERCONNECT 1
10 56109699 CAM, w/ GRIP, ASM. 1
11 80291A WASHER, FLAT, #10 1
12 980349 WASHER, WEAR 1
13 920342 NUT, HEX, 3/8” 1
14 980673 WASHER, FLAT, 1/2” 2
15 80290A SCREW, #10 X 3/8” 6
16 80292A SCREW, 1/4” X 1” 2
Item Ref. No. Description Qty
23A 53650A MOTOR, GEARBOX (120V) 1
23B 53652A MOTOR, GEARBOX (230V) 1
23C AS001900 MOTOR, GEARBOX, 120V, 2SPD 1
24 61716A COVER, DRIP, MOTOR 1
25 21088A FRAME, MAIN 1
26A MP481100 DRIVER, PAD, 16” 1
26B MP478400 DRIVER, PAD, 19” 1
27A 11006A SHROUD, 17”, ASM. 1
- 61715A SHROUD, 17” 1
- 30381A BUMPER, 17” 1
27B MP478000 SHROUD, 20”, ASM. 1
- MP473200 SHROUD, 20” 1
- MP478100 BUMPER, 20” 1
28 80294A SCREW, SH, 5/16” X 1-5/8” 4
29 53833A PIN, 1/2” X 2” 2
30 980603 WASHER, EXT TOOTH, #10 2
31 NB021600 CLAMP, 3/8” 1
17 39857A WHEEL, 5” 2
18 980648 WASHER, 17/32” X 1-1/16” 2
19 80295A WASHER, BOWED 2
20 61741A ARM, LINK, RIGHT 1
21 61725A AXLE 1
22 61740A ARM, LINK, LEFT 1
32 A0001-BLK4 TANK, 2-1/2 GAL, ASM. 1
33 NB6035 TIE, CABLE, 1/8” X 4”, BLK 2
34 MP473700 COUPLING, FEMALE, 3/8” 1
35 MP473800 COUPLING, MALE, 1/4” 1
36 NB064900 SCREW, #10 X 1/2” 1
37 MP473900 TUBING, PVC, 1/4” ID 12”
38 MP498300
DECAL, APEC, 3” (ON MOTOR)
(NOT SHOWN)
1
17
19
7
Main Assembly - 225FP17E6 & 225FP20E6
20
2
17
16
15
14
13
1
6
5
12
3
11
10
14
16
8
1
18
9
RF072800
13
15
17
4
080117
18
ITEM
4A
5
7
9
Main Assembly - 225FP17E6 & 225FP20E6
Parts List
QTY
4
PART NUMBER
53833A21
5610969912
92034213
9803491
MP51100016
MP5218001
61741A112
80295A213
39857A216
80292A217
11006A118A
MP478000118B
80290A320
PIN SPLIT 1/2 X 2.00 ZINC
CAM ASSY WITH GRIP
NUT LK 3/8 -16 REG
PAD DRIVER 17MP4811001
PAD DRIVER 20MP47840014B
WASHER WEAR CAM
HANDLE, ALUMINUM, EXPORT, ASM.
MOTOR/GEARBOX 1.5HP 230/60
MAIN FRAME21088A18
SCREW 5/16-18X1.63 HRCS SEMS80294A
AXLE .50 X 11.3461725A110
LINK ARM LEFT61740A111
LINK ARM RIGHT
WASHER BOWED .516ID X 1.06OD
WASH-17/32 ID X 1&1/16 OD PLN980648214
WASHER FLT 1/2 ID X 7/8 OD980673215
WHEEL 5 POLISHER
SCREW .25-20 X 1.00 BHHR SEMS
SHROUD, 17", W/BUMPER, ASM.
SHROUD, 20", W/BUMPER, ASM.
COVER, DRIP, MOTOR61716A119
SCREW, #10 X 3/8"
DESCRIPTION
RF072800
080117
19
Handle Assembly - 225FP E & E6 Models
8
5
1
10
7
1
9
12
4
6
11
3
2
RF071600
060917
20
ITEM
4
5
7
QTY
12
Handle Assembly - 225FP E & E6 Models
Parts List
PART NUMBER
80290A31
50781A13
61373A1
21075A1
21074A16
10687A1
80284A68
98060329
MP512000111
MP513000112A
MP514000112B
SCREW, 10-32 UNF X .375
CORD, INTERCONNECT, EXPORTAS018000
CLAMP HANDLE C2K
HANDLE TUBE
HANDLE, REAR - CFP
HANDLE, FRONT - CFP
INTERLOCK ASM.
SCREW, 10-32 UNF X .75
WASHER, LK 10 EXT TOOTH
WASHER, FLAT, #1080291A110
CORD, PIGTAIL, HANDLE, EXPORT, IEC
CORD, POWER SUPPLY, CE, IEC, RED
CORD, POWER SUPPLY, AUSTRALIAN, IEC
DESCRIPTION
RF071600
060917
21
HANDLE ASSEMBLY - 225FP17EB AND 225FP20EB MODELS
RF066700
22
HANDLE ASSEMBLY - 225FP17EB AND 225FP20EB MODELS
Item Ref. No. Description Qty
1 50780A HANDLE, REAR, C2K 1
2 30285A HANDLE FRONT C2K W/BLANK 1
3 50798A LEVER, SWITCH, C2K 2
4 50806A BUTTON, INTERLOCK, C2K 1
5 50799A INTERLOCK, MAIN, C2K 1
6 40109A SWITCH, MINIATURE-SPNO, C2K 2
7 50821A SPRING, COMPRESSION, C2K 1
8 50820A SPRING, EXTENSION, C2K 2
9 85383A SCREW 10-32 X 3/4 PAN HD 6
10 920722 BUT, 10-32 ELASTIC STOP ZN. PL. 7
11 962957 SCREW, 10-16 X 1/2 HI-LO 2
12 50930A CORD RETAINER, C2K 1
13 77094A LABEL, GROUND SYMBOL 1
14 170686 NUTLK FOR 1/2 CONDUIT 1
15 AS006800 DECAL “N” 1
16 80290A SCREW, 10-32 UNF X .375 1
17 MP506300 CORD, POWER SUPPLY, BRAZIL (EB) 1
17 AS018800 CORD, POWER SUPPLY, CE (E) 1
18 AS017400 HANDLE, TUBE, WELDMENT 1
19 AS018000 CORD, INTERCONNECT, EXPORT 1
20 50781A CLAMP HANDLE C2K 1
21 MP500900
DECAL, PE225FP, HANDLE,
EXPORT (NOT SHOWN)
1
RF066700
23
Motor & Gearbox Assembly
Item Ref. No. Description Qty
1 40694A CAPACITOR, START 1
2 53191A CAPACITOR, RUN 1
3 53360A COVER, CAPACITOR 2
4 53190A SWITCH, START 1
5 902550 BEARING, BALL, 6203 1
Item Ref. No. Description Qty
6 53848A PLATE, MOUNTING 1
7 40698A ENDBELL 1
8 41053A CORD, IEC 1
9 747553 RELIEF, STRAIN 1
24
17
Gearbox Assembly
1
4
14
16
13
8
13
11
9
5
15
16
7
3
18
10
13
6
12
Item Ref. No. Description Qty
1 53646A GEARBOX, ASM. 1
2 53647A GREASE, TUBE, 14OZ 1
3 54408A GEAR, PLANET 3
4 54856A GEAR, RING 1
5 54858A COVER, GEARBOX 1
Note: Use 8 ounces
of grease in Gearbox
53647A
2
Item Ref. No. Description Qty
10 58520A SPACER, SLEEVE 1
11 69195A COUPLING, SHAFT 1
12 80141A SCREW, SH, #10 X 1” 6
13 902606 BEARING, BALL, 6002 3
14 902654 BEARING, BALL, 6204 1
6 56922A RETAINER, BEARING 1
7 58312A SHAFT, PLANET 3
8 58313A GEAR, PINION 1
9 58314A RETAINER, SHAFT 1
15 902736 BEARING, BALL, 6010 1
16 902737 BEARING, NEEDLE 6
17 84808A SCREW, #10 X 3/4” 6
18 53848A PLATE, MOUNTING 1
25
2-Speed Motor Assembly
4
ELECTRICAL SCHEMATIC
(120V)
2-SPEED
13
6
10
18
17
14
16
13
8
13
11
9
5
15
16 3
7
Note: Use 8 ounces
of grease in Gearbox
53647A
1
2
12
Item Ref. No. Description Qty
1 53647A GEARBOX 1
2 503802 GREASE, 14oz TUBE
3 54408A GEAR, PLANET 3
4 54856A GEAR, RING 1
5 54858A COVER, GEARBOX 1
6 56922A RETAINER, BEARING 1
7 58312A SHAFT, PLANET 1
8 58313A GEAR, PINION 1
9 58314A RETAINER, SHAFT 1
10 58520A SPACER, SLEEVE 1
11 69195A COUPLING, SHAFT 1
12 80141A SCREW, #10 X 1” 6
13 902606 BEARING, BALL 6002 3
(NOT SHOWN) 1
Item Ref. No. Description Qty
14 902654 BEARING, BALL 6204 1
15 902736 BEARING, BALL 6010 1
16 902737 BEARING, NEEDLE 6
17 84808A SCREW, #10 X 3/4” 6
18 MP487800
REPLACEMENT MOTOR PARTS
19 MP487900 BRUSH, CARBON, ASM. 4
20 MP488000 RECTIFIER, MOTOR 1
21 MP488100 CONTROL, SPEED, ASM. 1
22 MP488200 COVER, DRIP 1
23 MP488300 CORDSET, 4-WIRE 1
24 MP488400 BEARING, TOP 1
25 MP488500 BEARING, BOTTOM 1
FLANGE, MOUNTING, GEARBOX
(NOT SHOWN)
26
1
Limited Warranty
PE225FP
TO QUALIFY FOR THIS WARRANTY
(1) Machine must be registered at the time of purchase on a form
provided by Amano Pioneer Eclipse Corporation. Your Amano
Pioneer Eclipse Corporation Distributor is responsible for the
registration of your machine. Please cooperate with your
Distributor in supplying necessary information on the card.
(2) The machine must have been purchased from Amano Pioneer
Eclipse Corporation or an authorized Amano Pioneer Eclipse
Corporation Distributor.
(3) This warranty extends to the original purchaser only and is not
transferable to subsequent owners.
TIME PERIODS
(1) FIVE (5) YEAR WARRANTY - Motor, shroud, and frame.
(2) ONE (1) YEAR WARRANTY - For the PE225FP
Warranted to be free from defects in material and workmanship
for a period of one (1) year from the date of purchase by the
original owners. (See Exclusions.)
EXCLUSIONS (Not Covered by Warranty)
(1) Parts that fail through normal wear by reason of their
characteristics (cords, motor brushes, wheels, pad holder, skirt,
or other consumable parts).
(2) This warranty does not extend to parts affected by misuse,
neglect, abuse or improper maintenance. All defective parts
must be returned to the distributor for credit.
THE OBLIGATION OF AMANO PIONEER ECLIPSE
CORPORATION
(1) The obligation of Amano Pioneer Eclipse Corporation under this
warranty is limited to repairing or replacing, at its option, any
part which is proven to be defective in material or workmanship
under normal use for the applicable period stated above.
(2) Warranty repairs will be made by your Amano Pioneer Eclipse
Corporation Distributor without charge for parts and labor. They
will be compensated with a warranty labor rate of $45.00 per
hour, for the first year of ownership.
(3) Parts repaired or replaced under this warranty are warranted
only during the balance of the original warranty period. All
defective parts replaced under these warranties become the
property of Amano Pioneer Eclipse Corporation.
WARRANTY SERVICE
To obtain warranty service, take your machine and proof of
purchase to any authorized Amano Pioneer Eclipse Corporation
Distributor. Amano Pioneer Eclipse Corporation will not reimburse
expenses for service calls or travel. For the Distributor in your
area, call Amano Pioneer Eclipse Corporation Customer Service
Department at 1-800-367-3550 or 1-336-372-8080. If you are
dissatisfied with the service that you receive, call or email Amano
Pioneer Eclipse Corporation Customer Service Department at
apeccs@pioneer-eclipse.com for further assistance.
INSTRUCTIONS AND CONDITIONS FOR WARRANTY
REIMBURSEMENT
l Order replacement part: Orders will be processed and charged,
as normal procedure.
l Call Amano Pioneer Eclipse Corporation for R/A number.
l You will need the Engine Serial Number, Machine Serial
Number, and the Machine Model Number.
l Parts must be returned, accompanied with the R/A number to
be eligible for warranty credit.
l All Warranty Parts will be shipped prepaid UPS Ground, any
other method will be at the recipients expense.
l Freight on any Warranty Part after 30 days must be paid for by
the Purchaser.
l Warranty labor rate is $45.00 per hour.
l Credit will be issued upon completion of the above steps, at the
above rates.
DISCLAIMER OF CONSEQUENTIAL
AMANO PIONEER ECLIPSE CORPORATION DISCLAIMS ANY
RESPONSIBILITY FOR LOSS OF USER TIME OF THE AMANO
PIONEER ECLIPSE CORPORATION MACHINE OR ANY OTHER
INCIDENTAL OR CONSEQUENTIAL DAMAGE EXCEPT AS
STATED IN THE WARRANTY APPLICABLE TO EACH MACHINE.
EXCEPT AS STATED IN SUCH WARRANTIES, THE COMPANY
DOES NOT OTHERWISE WARRANT ANY MACHINE AND NO
WARRANTY, EXPRESS, IMPLIED OR STATUTORY IS MADE BY
THE COMPANY.
Copyright 2017 Amano Pioneer Eclipse Corporation
LT071200_G; 120817
27
Amano Pioneer Eclipse Corporation
1 Eclipse Rd l PO Box 909
Sparta, North Carolina 28675 l USA
www.pioneereclipse.com
+1-336-372-8080
1-800-367-3550
Fax +1-336-372-2913
Harmonized Standards Applied: EN ISO 12100:2010, EN 60335-2-67:2012
© 2017 Amano Pioneer Eclipse Corporation
Machinery Directive 2006/42/EC
ROHS Directive 2011/65/EU
EMC Directive 2014/30/EU
LT071200
225FP_G
Loading...