Pioneer Premier DEH-P590IB, P590IB - Premier Radio / CD Installation Manual

Installation ENGLISH

Note:

• Check all connections and systems before final
installation.

• Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.

• Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.

• Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result

of a sudden stop.

• The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.

• Optimum performance is obtained when the unit
is installed at an angle of less than 60°.

DIN Front/Rear-mount

This unit can be properly installed either from
“Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit chassis).
For details, refer to the following installation
methods.

DIN Front-mount

Installation with the rubber bush

1. Insert the mounting sleeve into the dashboard.

• When installing in a shallow space, use a sup­plied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.

2. Secure the mounting sleeve by using a screwdriv­er to bend the metal tabs (90°) into place.

3. Install the unit as illustrated.

Removing the Unit

1. Extend top and bottom of the trim ring outwards
to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)

• It becomes easy to remove the trim ring if the

front panel is released.

2. Insert the supplied extraction keys into both sides
of the unit until they click into place.

3. Pull the unit out of the dashboard.

53

53

182182

60°

Trim ring

Dashboard

Mounting sleeve

Rubber bush

Screw

DIN Rear-mount

1. Extend top and bottom of the trim ring outwards
to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)

• It becomes easy to remove the trim ring if the

front panel is released.

2. Determine the appropriate position where the
holes on the bracket and the side of the unit
match.

3. Tighten two screws on each side.

• Use either truss screws (5 mm

× 8 mm) or
flush surface screws (5 mm × 9 mm), depend­ing on the shape of screw holes in the
bracket.

Fastening the front panel

If you do not plan to detach the front panel, the
front panel can be fastened with supplied screws
and holders.

1. Attach the holders to both sides of the front panel.

2. Replace the front panel to the unit.

3. Flip the holders into upright positions.

4. Fix the front panel to the unit using screws.

Trim ring

Screw

Dashboard or Console

Factory radio mounting bracket

Screw

Holder

Note:

• When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key.
Otherwise, battery drain may result.

• Use this unit in other than the following condi­tions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunc­tion, be sure to follow the directions below.
— Disconnect the negative terminal of the battery

before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhesive
tape around them where they lie against metal
parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a
battery.

— Cover any disconnected cable connectors with

insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly

to ground.
— Never band together multiple speaker’s nega-

tive cables.

• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or
the vehicle’s auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.

• Never connect blue/white cable to external power
amp’s power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.

• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.

• Black cable is ground. This cable and other prod­uct’s ground cable (especially, high-current prod­ucts such as power amp) must be wired separate­ly. Otherwise, fire or malfunction may result if
they are accidentally detached.

• Cord function may differ according to the
product, even if cord color is the same. When
connecting this system, be sure to check all
manuals and connect cords correctly.

No ACC positionACC position

O

N

S

T

A

R

T

O

F

F

A

C

C

O

N

S

T

A

R

T

O

F

F

<KMMZX> <06J00000>

DEH-P590IB

Printed in Thailand
Imprimé en Thaïlande

<XRD7141-A/N> UC

Connecting the Units ENGLISH

This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.

INSTALLATION MANUAL

MANUEL D’INSTALLATION

++

≠≠

++

++

≠≠

≠≠

+

≠

+

≠

+

≠

+

≠

Power amp
(sold separately)

Subwoofer

Yellow
Connect to the constant 12 V supply terminal.

Red
Connect to terminal controlled by ignition switch (12 V DC).

Orange/white
Connect to lighting switch terminal.

Connect with RCA cables
(sold separately)

Rear speaker

Perform these connections when
using the optional amplifier.

Yellow/black
If you use an equipment with Mute function, wire this lead to the Audio
Mute lead on that equipment. If not, keep the Audio Mute lead free of any
connections.

Use a stereo mini plug cable
to connect with auxiliary
equipment

.

Black (chassis ground)
Connect to a clean, paint-free metal location.

iPod with Dock
Connector

Dock connector port

Dock connector

Interface cable

This product

Rear output
Front output

Antenna jack

Subwoofer output

Fuse (10 A)

AUX jack (3.5 ø)

IP-BUS in

put

(Blue)

IP-BUS cable

Multi-CD player
(sold separately)

System remote control

Front speaker Front speaker

Left Right

Rear speaker

Subwoofer

Gray

Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal (max.
300 mA 12 V DC).

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

Front speaker Front speaker

Rear speaker Rear speaker

White Gray

Gray/blackWhite/black

Green Violet

Green/black Violet/black

Wired remote in

put

ard-wired remote control
adaptor can be connected (sold
separately)

.

Power amp
(sold separately)

Power amp
(sold separately)

2 m (6 ft. 7 in.)

15 cm (5­7/8 in.)

Connecting the Units ENGLISH

7 When not connecting a rear speaker lead to a Subwoofer

+

≠

+

≠

+

≠

+

≠

+

≠

Yellow
Connect to the constant 12 V supply terminal.

Red
Connect to terminal controlled by ignition switch (12 V DC).

Orange/white
Connect to lighting switch terminal.

Yellow/black
If you use an equipment with Mute function, wire this lead to the Audio
Mute lead on that equipment. If not, keep the Audio Mute lead free of any
connections.

Use a stereo mini plug cable
to connect with auxiliary
equipment.

Black (chassis ground)
Connect to a clean, paint-free metal location.

This product

Front output

Antenna jack

Subwoofer output

Fuse (10 A)

AUX jack (3.5 ø)

IP-BUS input
(Blue)

IP-BUS cable

Multi-CD player
(sold separately)

Left Right

Gray

Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal (max.
300 mA 12 V DC).

Front speaker Front speaker

White Gray

Gray/blackWhite/black

Green Violet

Green/black Violet/black

Green Violet

Green/black Violet/black

Subwoofer (4 Ω) Subwoofer (4 Ω)

When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit.
Do not connect anything with Green and Green/black leads.

Subwoofer
(4 Ω) × 2

Not used.

Note:

Change the initial setting of this unit (refer to the Operation
Manual). The subwoofer output of this unit is monaural.

Subwoofer output

Wired remote input
Hard-wired remote control
adaptor can be connected (sold
separately).

iPod with Dock
Connector

Dock connector port

Dock connector

Interface cable

2 m (6 ft. 7 in.)

15 cm (5­7/8 in.)

7 When using a Subwoofer without using the optional amplifier