Pioneer GEX-P10XMT User Manual 2
INSTALLATION MANUAL
INSTALLATION MANUAL
<KKYZX> <04L00000>
GEX-P10XMT
Printed in Thailand
<CRB2046-A/N> UC
Connecting the Units
Note:
• This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery
voltage.
• To avoid shorts in the electrical system, be sure to
disconnect the ≠ battery cable before beginning
installation.
• Refer to the owner’s manual for details on
connecting the power amp and other units, then
make connections correctly.
• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around wires that lie against metal parts.
• Securely route all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake and
seat rails. Do not route wiring through places that
get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle
body.
Don’t pass the yellow lead through a hole into the
engine compartment to connect to the battery. This
will damage the lead insulation and cause a very
dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing the fuse, be sure to only use a fuse
of the rating prescribed on the fuse holder.
• To prevent incorrect connection, the input side of
the IP-BUS connector is colored blue, and the output side is colored black. Connect the connectors
of the same
colors correctly.
This product conforms to CEMA cord colors.
• Cords for this product and those for other products
may be different colors even if they have the same
function. When connecting this product to another
product, refer to the manuals supplied with both
products and connect cords that have the same
function.
To safeguard from electromagnetic interference
• In order to prevent interference, set the following
items as far as possible from this unit, its cables or
leads:
– TV antenna and antenna lead
– FM, AM antenna and its lead
– GPS antenna and its lead
In addition route each antenna lead as far as possible from other antenna leads. Do not bind them
together, lay or route them together, or cross them
over each other. Increased interference could lead
to TV reception appearing fuzzy.
Connecting the Units
Connecting the power cord and antenna
Connecting the system (1)
When using this product with the head unit (or AV head unit) using the IP-BUS only, connect each piece of equipment as below.
This product
Head Unit
(sold separately)
IP-BUS cable
(supplied)
To IP-BUS input (blue)
IP-BUS output
(black)
IP-BUS input
(blue)
Multi-CD player
(sold separately)
IP-BUS cable
Not used.
Black
Blue
3 m (9 ft. 10 in.)
This product
Antenna Input
Power Supply
Antenna Unit
Violet
Yellow
To terminal always supplied with power
regardless of ignition switch position.
Black (ground)
To vehicle (metal) body.
Fuse holder (2 A)
Red
To electric terminal controlled
by ignition switch (12 V DC) ON/OFF.
5m (16 ft. 5 in.)
Fuse resistor
Connecting the system (2)
When connecting this product to the unit, support the data communication functions (e.g.
AVIC-D1, AVIC-N2, AVIC-N1) by both an IP-BUS and XM DATA cable, connect each
equipment as below.
Navigation system (sold separately) (e.g. AVIC-D1, AVIC-N2, AVIC-N1)
Note:
When combining this product with
AVIC-N1 (sold separately), be sure to
updated with the latest map disc
CNDV-50MT [CNDV-50MTP] (sold
separately) to utilize traffic and data
functionality.
Note:
When combining this product with Pioneer navigation system
(sold separately), this connection is required.
IP-BUS Input
DATA OUT port
This product
IP-BUS cable (supplied)
To IP-BUS Input
(Blue)
Multi-CD player
(sold separately)
IP-BUS cable
Black
Blue
3 m (9 ft. 10 in.)
Hide-away unit
EXTENSION port
Display unit
Blue
To EXTENSION
port
3 m (9 ft. 10 in.)
Black
Black
XM DATA cable
Loading...