Pioneer DEH-33HD User Manual

CD RECEIVER AUTORADIO CD RADIO CD
English
DEH-33HD
EspañolFrançais
Owner’s Manual
Mode d’emploi
Manual de instrucciones
Section
01
Before You Start
Before You Start
Thank you for purchasing this PIONEER product.
To ensureproperuse,please read through this manual before using this product. It is especially important that you read and obser ve WARN-
INGs and CAUTIONs in this manual. Please keep the manual in a safe and accessible place for future reference.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful inter­ference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Information to User
Alteration or modifications carried out with­out appropriate authorization may invalidate the user s right to operate the equipment.
For Canadian model
This Class B digital apparatus complies with Canadian ICES-003.
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a safe levela level that lets the sound come through clearly without annoying blaring or dis­tortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving. Over time, your hearing comfort leveladapts to higher volumes of sound, so what sounds nor­malcan actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.
ESTABLISH A SAFE LEVEL:
! Set your volume control at a low setting. ! Slowly increase the sound until you can hear
it comfortably and clearly, without distortion.
! Once you have established a comfortable
sound level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:
! Do not turn up the volume so high that you
cant hear whats around you.
! Use caution or temporarily discontinue use
in potentially hazardous situations.
! Do not use headphones while operating a
motorized vehicle; the use of headphones may create a traffic hazard and is illegal in many areas.
About this unit
The tuner frequencies on this unit are allocated for use in North America. Use in other areas may result in poor reception.
WARNING
Handling the cord on this product or cords asso­ciated with accessories sold with the product may expose you to chemicals listed on proposi­tion 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm. Wash
hands after handling.
CAUTION: USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.
CAUTION
! Do not allow this unit to come into contact
with liquids. Electrical shock could result. Also, damage to this unit, smoke, and over­heating could result from contact with liquids.
! Always keep the volume low enough to hear
outside sounds.
! Avoid exposure to moisture. ! If the battery is disconnected or discharged,
any preset memory will be erased.
Important (Serial number)
The serial number is located on the bottom of this unit. For your own security and conven­ience, be sure to record this number on the en­closed warranty card.
Note
Function setting operations are completed even if the menu is cancelled before the operations are confirmed.
Demo mode
Important
! Failure to connect the red lead (ACC) of this
unit to a terminal coupled with ignition switch on/off operations may lead to battery drain.
! Remember that if the feature demo contin-
ues operating when the car engine is turned off, it may drain battery power.
The demo automatically starts when the ignition switch is set to ACC or ON while the unit is turned off. Turning off the unit does not cancel demo mode. To cancel the demo mode, operate the function in the initial setting menu. Operat­ing the demo while the ignition switch is set to ACC may drain battery power.
After-sales service for Pioneer products
Please contact the dealer or distributor from where you purchased this unit for after-sales service (including warranty conditions) or any other information. In case the necessary infor­mation is not available, please contact the com­panies listed below: Please do not ship your unit to the companies at the addresses listed below for repair without ad­vance contact.
2
En
Before You Start
Operating this unit
Section
02
English
U.S.A.
Pioneer Electronics (USA) Inc. CUSTOMER SUPPORT DIVISION P.O. Box 1760 Long Beach, CA 90801-1760 800-421-1404
CANADA
Pioneer Electronics of Canada, Inc. CUSTOMER SATISFACTION DEPARTMENT 300 Allstate Parkway Markham, Ontario L3R 0P2 1-877-283-5901 905-479-4411
For warranty information please see the Limited Warranty sheet included with this unit.
In case of trouble
Should this unit fail to operate properly, please contact your dealer or nearest authorized PIONEER Service Station.
Visit our website
http://www.pioneerelectronics.com
in Canada
http://www.pioneerelectronics.ca
! Learn about product updates (such as firm-
ware updates) for your product.
! Register your product to receive notices
about product updates and to safeguard pur­chase details in our files in the event of loss or theft.
! Access owner's manuals, spare parts infor-
mation, service information, and much more.
Head unit
24 5 63
1
78 a b cd9
Part Part
1 S (SRC/OFF) 8
2 h (eject) 9 a/b/c/d
(list) a (clock)
3
MULTI-CONTROL
4
(M.C.)
5 Disc loading slot c
6 USB port d Detach button
7 B (BAND/ESC)
CAUTION
! Use an optional Pioneer USB cable (CD-
U50E) to connect the USB audio player/USB memory as any device connected directly to the unit will protrude out from the unit and may be dangerous.
! Do not use unauthorized products.
scroll)
b 1 to 6
AUX input jack (3.5 mm stereo jack)
(Back/display/
Remote control
7
k
1 i
Part Operation
e VOLUME
f MUTE
g AUDIO
h DISP/SCRL
i e
FUNC-
j
TION
LIST/
k
ENTER
Press to increase or decrease volume.
Press to mute. Press again to unmute.
Press to select an audio func­tion.
Press to select different dis­plays. Press and hold to scroll through the text information.
Press to pause or resume play­back.
Press to select functions. Press and hold to recall the ini­tial setting menu when the sources are off.
Press to display the disc title, track title, folder, or file list de­pending on the source. While in the operating menu, press to control functions.
e
f 9 gj
h
3
En
Section
02
Operating this unit
Operating this unit
Display indication
1
3
2
6
8
4 5
Indicator State
Main dis-
1
play sec­tion
2 c
3 d
(list)
4
(artist)
5
6
(disc)
9
7
! Tuner: band and frequency ! Built-in CD, USB storage
device and iPod: elapsed playback time and text in­formation
An upper tier of the folder or menu exists.
A lower tier of the folder or menu exists. This flashes when a song/ album related to the song cur­rently playing is selected from the iPod.
The list function is being oper­ated.
Certain information from radio station is received. The artist name is displayed. Artist search refinement of the iPod browsing function is in use.
Certain information from radio station is received. The disc (album) name is dis­played. Album search refinement of the iPod browsing function is in use.
Indicator State
Certain information from radio station is received. The track (song) name is dis­played.
7
b
a
8 LOC Local seek tuning is on.
9
peat)
dom/shuf-
a
fle)
b
(sound re­triever)
A playable audio file has been
(song)
selected during operation of the list. Song search refinement of the iPod browsing function is in use.
(re-
Track or folder repeat is on.
Random play is on.
(ran-
The iPod source is selected and the shuffle or shuffle all function is on.
The sound retriever function is on.
Basic Operations
Important
! Handle gently when removing or attaching
the front panel.
! Avoid subjecting the front panel to excessive
shock.
! Keep the front panel out of direct sunlight
and high temperatures.
! To avoid damaging the device or vehicle inte-
rior, remove any cables and devices attached to the front panel before detaching it.
Removing the front panel to protect your unit from theft 1 Press the detach button to release the front
panel.
2 Push the front panel upward and pull it toward
you.
3 Always keep the detached front panel in a pro-
tection device such as a protection case.
Re-attaching the front panel 1 Slide the front panel to the left.
Make sure to insert the tabs on the left side of the head unit into the slots on the front panel.
2 Press the right side of the front panel until it is
firmly seated. If you cannot attach the front panel to the head unit successfully, make sure that you are placing the front panel onto the head unit cor­rectly. Forcing the front panel into place may result in damage to the front panel or head unit.
Turning the unit on 1 Press S (SRC/OFF) to turn the unit on.
Turning the unit off 1 Press and hold S (SRC/OFF) until the unit
turns off.
Selecting a source
1 Press S (SRC/OFF) to cycle between:
TUNER (tuner)CD (built-in CD player)USB
(USB)/iPod (iPod)AUX (auxiliary)
Adjusting the volume 1 Turn M.C. to adjust the volume.
CAUTION
For safety reasons, park your vehicle when re­moving the front panel.
Note
When this units blue/white lead is connected to the vehicles auto-antenna relay control termi­nal, the vehicles antenna extends when this units source is turned on. To retract the anten­na, turn the source off.
Use and care of the remote control
Using the remote control 1 Point the remote control in the direction of the
front panel to operate. When using for the first time, pull out the film protruding from the tray.
Replacing the battery 1 Slide the tray out on the back of the remote
control.
2 Insert the battery with the plus (+) and minus
(–) poles aligned properly.
4
En
Operating this unit
Operating this unit
Section
02
English
WARNING
! Keep the battery out of the reach of children.
Should the battery be swallowed, consult a doctor immediately.
! Batteries (battery pack or batteries installed)
must not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION
! Use one CR2025 (3 V) lithium battery. ! Remove the battery if the remote control is
not used for a month or longer.
! There is a danger of explosion if the battery is
incorrectly replaced. Replace only with the same or equivalent type.
! Do not handle the battery with metallic tools. ! Do not store the battery with metallic ob-
jects.
! If the battery leaks, wipe the remote control
completely clean and install a new battery.
! When disposing of used batteries, comply
with governmental regulations or environ­mental public institutionsrules that apply in your country/area.
! “Perchlorate Material – special handling may
apply. See
www.dtsc.ca.gov/hazardouswaste/ perchlorate. (Applicable to California, U.S.A.)
Important
! Do not store the remote control in high tem-
peratures or direct sunlight.
! The remote control may not function properly
in direct sunlight.
! Do not let the remote control fall onto the
floor, where it may become jammed under the brake or accelerator pedal.
Menu operations identical for function settings/audio adjustments/initial settings/ lists
Returning to the previous display Returning to the previous list (the folder one level higher)
.
1 Press
Returning to the main menu Returning to the top tier of list 1 Press and hold
Returning to the ordinary display Canceling the initial setting menu 1 Press B (BAND/ESC).
Returning to the ordinary display from the list 1 Press B (BAND/ESC).
.
Tuner
About HD Radioä broadcasting
HD Radioä broadcasting is high quality audio and data services. HD Radio broadcasting is brought to you by your local FM/AM stations. HD Radio broadcasting features the following:
! High quality audio ! FM multicasting ! Data services
Basic Operations
Selecting a band 1 Press B (BAND/ESC) until the desired band
(F1, F2, F3 for FM or AM) is displayed.
Manual tuning (step by step) 1 Press c or d.
! When an analog station is received, tuning
down operation is conducted within the analog broadcasting. (6 d 2)
! If a digital broadcast is not yet received,
tuning-up operation tunes in the next ana­log station. (2 d 6)
Seeking 1 Press and hold c or d, and then release.
You can cancel seek tuning by briefly pressing c or d. While pressing and holding c or d, you can skip stations. Seek tuning starts as soon as you release c or d.
Storing and recalling stations for each band
Using preset tuning buttons
1 When you find a station that you want to store in memory, press one of the preset tuning buttons (1 to 6) and hold until the preset number stops flashing.
5
En
Section
02
Operating this unit
Operating this unit
2 Press one of the preset tuning buttons (1 to 6) to select the desired station.
# You can also recall stored radio stations by press­ing a or b during the frequency display.
Switching the display
Selecting the desired text information
.
1 Press
Station namesong titleartist name album titlegenrefrequency
Scrolling the tuner information to the left 1 Press and hold
.
Note
Depending on the area, you cannot switch the display.
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following proce­dures to set the function.
BSM (best stations memory)
BSM (best stations memory) automatically stores the six strongest stations in the order of their sig­nal strength. 1 Press M.C. to turn BSM on.
To cancel, press M.C. again.
LOCAL (local seek tuning)
Local seek tuning lets you tune in to only those radio stations with sufficiently strong signals for good reception.
1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.
FM: OFFLEVEL 1LEVEL 2LEVEL 3 LEVEL 4
AM: OFFLEVEL 1LEVEL 2 The highest level setting allows reception of only the strongest stations, while lower levels allow the reception of weaker stations.
3 Press M.C. to confirm the selection.
SEEK MODE (seek mode)
Seek tuning setting can be changed between digi­tal station seek (HD) and analog station seek (ALL) depending on the reception status.
1 Press M.C. to display the setting mode. 2 Turn M.C. to select your favorite setting.
ALLHD
BLEND (reception mode)
If a digital broadcast reception condition gets poor, this unit automatically switches to the ana­log broadcast of the same frequency level. If this function is set to on, the tuner switches between digital broadcast and analog broadcast automati­cally. If this function is off, reception will be con­ducted within an analog broadcast. 1 Press M.C. to turn this function on or off.
Note
If SEEK MODE is set to HD and BLEND is set to off, the tuner cannot receive broadcasts. In this case, the seek mode or reception mode is changed automatically as follows:
! When SEEK MODE is set to HD, if you switch
BLEND from on to off, SEEK MODE is changed to ALL.
! When BLEND is set to off, if you switch
SEEK MODE from ALL to HD, BLEND is changed
to on.
CD/CD-R/CD-RW and USB storage devices
Basic Operations
Playing a CD/CD-R/CD-RW 1 Insert the disc into the disc loading slot with
the label side up.
Ejecting a CD/CD-R/CD-RW 1 Press h.
Playing songs on a USB storage device 1 Open the USB connector cover and plug in
the USB storage device using a USB cable.
Stopping playback of files on a USB storage de­vice 1 You may disconnect the USB storage device at
any time.
Selecting a folder 1 Press a or b.
Selecting a track 1 Press c or d.
Fast forwarding or reversing 1 Press and hold c or d. ! When playing compressed audio, there is no
sound during fast forward or reverse.
Returning to root folder 1 Press and hold B (BAND/ESC).
Switching between compressed audio and CD-DA 1 Press B (BAND/ESC).
Note
Disconnect USB storage devices from the unit when not in use.
Displaying text information
Selecting the desired text information 1 Press
.
Scrolling the text information to the left 1 Press and hold
.
Notes
! Depending on the version of iTunes used to
write MP3 files to a disc or media file types, incompatible text stored within an audio file may be displayed incorrectly.
! Text information items that can be changed
depend on the media.
Selecting and playing files/ tracks from the name list
1 Press to switch to the file/track name list mode.
2 Use M.C. to select the desired file name (or folder name).
Changing the file or folder name 1 Turn M.C.
Playing 1 When a file or track is selected, press M.C.
Viewing a list of the files (or folders) in the se­lected folder 1 When a folder is selected, press M.C.
Playing a song in the selected folder 1 When a folder is selected, press and hold M.C.
6
En
Operating this unit
Advanced operations using special buttons
Selecting a repeat play range 1 Press 6/
Playing tracks in random order 1 Press 5/
Pausing playback 1 Press 2/PAUSE to pause or resume.
Enhancing compressed audio and restoring rich sound (sound retriever) 1 Press 1/S.Rtrv to cycle between:
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following proce­dures to set the function.
to cycle between the following:
CD/CD-R/CD-RW
! DISC – Repeat all tracks ! TRACK – Repeat the current track ! FOLDER – Repeat the current folder
USB audio player/USB memory
! ALL – Repeat all files ! TRACK – Repeat the current file ! FOLDER – Repeat the current folder
to turn random play on or off. Tracks in a selected repeat range are played in random order.
OFF (off)12 1 is effective for low compression rates, and 2
is effective for high compression rates.
REPEAT (repeat play)
1 Press M.C. to display the setting mode. 2 Turn M.C. to select a repeat play range.
For details, refer to Selecting a repeat play range on this page.
3 Press M.C. to confirm the selection.
RANDOM (random play)
1 Press M.C. to turn random play on or off.
PAUSE (pause)
1 Press M.C. to pause or resume.
S.RTRV (sound retriever)
Automatically enhances compressed audio and restores rich sound.
1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.
For details, refer to Enhancing compressed audio and restoring rich sound (sound retriever)
on this page.
3 Press M.C. to confirm the selection.
iPod
Basic Operations
Playing songs on an iPod
1 Open the USB connector cover. 2 Connect an iPod to the USB cable using an
iPod Dock Connector.
Selecting a track (chapter) 1 Press c or d.
Fast forwarding or reversing 1 Press and hold c or d.
Notes
! The iPod cannot be turned on or off when the
control mode is set to CTRL AUDIO.
Operating this unit
! Disconnect headphones from the iPod be-
fore connecting it to this unit.
! The iPod will turn off about two minutes after
the ignition switch is set to OFF.
Displaying text information
Selecting the desired text information
.
1 Press
Scrolling the text information to the left 1 Press and hold
Browsing for a song
1 Press to switch to the top menu of list search.
2 Use M.C. to select a category/song.
Changing the name of the song or category 1 Turn M.C.
Playlistsartistsalbumssongspodcasts genrescomposersaudiobooks
Playing 1 When a song is selected, press M.C.
Viewing a list of songs in the selected category 1 When a category is selected, press M.C.
Playing a song in the selected category 1 When a category is selected, press and hold
M.C.
Searching the list by alphabet 1 When a list for the selected category is dis-
played, press mode.
2 Turn M.C. to select a letter. 3 Press M.C. to display the alphabetical list.
.
to switch to alphabet search
Advanced operations using special buttons
Selecting a repeat play range 1 Press 6/
Playing all songs in random order (shuffle all) 1 Press 5/ ! When the control mode is set to CTRL iPod/
Pausing playback 1 Press 2/PAUSE to pause or resume.
Playing songs related to the currently playing song You can play songs from the following lists.
Album list of the currently playing artist
Song list of the currently playing album
Album list of the currently playing genre
1 Press and hold M.C. to switch to link play
2 Turn M.C. to change the mode; press to select.
The selected song/album may be canceled if you operate functions other than link search (e.g. fast forward and reverse). Depending on the song selected to play, the end of the currently playing song and the beginning of the selected song/album may be cut off.
to cycle between the following:
! ONE – Repeat the current song ! ALL – Repeat all songs in the selected list
to turn shuffle all on.
CTRL APP,shuffle play is on.
mode.
! ARTIST – Plays an album of the artist cur-
rently being played.
! ALBUM – Plays a song from the album
currently being played.
! GENRE – Plays an album from the genre
currently being played. The selected song/album will be played after the currently playing song.
Section
02
English
7
En
Section
02
Operating this unit
Operating this unit
Operating this units iPod function from your iPod You can listen to the sound from your iPod appli­cations using your car's speakers, when CTRL APP is selected. This function is not compatible with the following iPod models.
! iPod nano 1st generation ! iPod 5th generation
APP mode is compatible with the following iPod models.
! iPhone 3GS (software version 3.1.2 or later) ! iPhone 3G (software version 3.1.2 or later) ! iPhone (software version 3.1.2 or later) ! iPod touch 3rd generation (software version
4.0 or later)
! iPod touch 2nd generation (software version
3.1.2 or later)
! iPod touch 1st generation (software version
3.1.2 or later)
1 Press 4/iPod to switch the control mode.
! CTRL iPod – This units iPod function can
be operated from the connected iPod.
! CTRL APP – Play back the sound from your
iPod applications.
! CTRL AUDIO – This units iPod function
can be operated from this unit.
Enhancing compressed audio and restoring rich sound (sound retriever)
1 Press 1/S.Rtrv to cycle between:
OFF (off)12 1 is effective for low compression rates, and 2
is effective for high compression rates.
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following proce­dures to set the function.
REPEAT (repeat play)
1 Press M.C. to display the setting mode. 2 Turn M.C. to select a repeat play range.
For details, refer to Selecting a repeat play range on the previous page.
3 Press M.C. to confirm the selection.
SHUFFLE (shuffle)
1 Press M.C. to display the setting mode. 2 Turn M.C. to select your favorite setting.
! SONGS – Play back songs in the selected
list in random order.
! ALBUMS – Play back songs from a ran-
domly selected album in order.
! OFF – Cancel random play.
3 Press M.C. to confirm the selection.
SHUFFLE ALL (shuffle all)
1 Press M.C. to turn shuffle all on.
To turn off, set SHUFFLE in the FUNCTION menu to off.
LINK PLAY (link play)
1 Press M.C. to display the setting mode. 2 Turn M.C. to change the mode; press to select.
For details about the settings, refer to Playing songs related to the currently playing song on
the previous page.
PAUSE (pause)
1 Press M.C. to pause or resume.
AUDIO BOOK (audiobook speed)
1 Press M.C. to display the setting mode. 2 Turn M.C. to select your favorite setting.
! FASTER – Playback at a speed faster than
normal
! NORMAL – Playback at normal speed ! SLOWER – Playback at a speed slower
than normal
3 Press M.C. to confirm the selection.
S.RTRV (sound retriever)
Automatically enhances compressed audio and restores rich sound.
1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.
For details, refer to Enhancing compressed audio and restoring rich sound (sound retriever)
on this page.
3 Press M.C. to confirm the selection.
Notes
! Switching the control mode to CTRL iPod
pauses song playback. Operate the iPod to resume playback.
! The following functions are still accessible
from the unit even if the control mode is set to CTRL iPod/CTRL APP.
PausingFast forward/reverseTrack up/downRepeat play (ONE/ALL/OFF)Random play (shuffle)
(list) to use iPod menu
— — a to turn the iPod click wheel to the leftb to turn the iPod click wheel to the right
! When the control mode is set to CTRL iPod,
operations are limited as follows:
The function settings are not available.The browse function cannot be operated from
this unit.
Audio Adjustments
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option and press to select AUDIO.
3 Turn M.C. to select the audio function.
After selecting, perform the following proce­dures to set the audio function.
FAD/BAL (fader/balance adjustment)
1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between fader (front/rear)
and balance (left/right). 3 Turn M.C. to adjust speaker balance. ! When the rear output and RCA output setting
are SW, you cannot adjust front/rear speaker
balance. Refer to SW CONTROL (rear output
and subwoofer setting) on the next page.
EQUALIZER (equalizer recall)
1 Press M.C. to display the setting mode. 2 Turn M.C. to select the equalizer.
DYNAMICVOCALNATURALCUSTOM
FLATPOWERFUL
3 Press M.C. to confirm the selection.
TONE CTRL (equalizer adjustment)
! Adjusted equalizer curve settings are stored in
CUSTOM.
1 Press M.C. to display the setting mode. 2 Press M.C. to select BASS (bass)/MID (mid)/
TREBLE (treble).
3 Turn M.C. to adjust the level.
Adjustment range: +6 to -6
LOUDNESS (loudness)
8
En
Operating this unit
Operating this unit
Section
02
English
Loudness compensates for deficiencies in the low­and high-frequency ranges at low volume.
1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.
OFF (off)LOW(low)HIGH (high)
3 Press M.C. to confirm the selection.
SUBWOOFER1 (subwoofer on/off setting)
This unit is equipped with a subwoofer output which can be turned on or off.
1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting.
NORMAL (normal phase)REVERSE (reverse phase)OFF (subwoofer off)
3 Press M.C. to confirm the selection.
SUBWOOFER2 (subwoofer adjustment)
The cut-off frequency and output level can be ad­justed when the subwoofer output is on. Only frequencies lower than those in the selected range are outputted from the subwoofer.
1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the cut-off fre-
quency and output level of the subwoofer. Cut-off frequency (Cut-off frequency display flashes.)Output level (Output level display flashes.)
3 Turn M.C. to select the desired setting.
Cut-off frequency: 50HZ63HZ80HZ
100HZ125HZ Output level: -24 to +6
SLA (source level adjustment)
SLA (Source Level Adjustment) lets you adjust the
volume level of each source to prevent radical changes in volume when switching between sour­ces. ! Settings are based on the FM volume level,
which remains unchanged.
! The AM volume level can also be adjusted with
this function.
! When selecting FM as the source, you cannot
switch to SLA.
1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the source volume.
Adjustment range: +4 to –4
3 Press M.C. to confirm the selection.
Initial Settings
1 Press and hold S (SRC/OFF) until the unit turns off.
2 Press M.C. and hold until function name appears in the display.
3 Turn M.C. to select the initial setting.
After selecting, perform the following proce­dures to set the initial setting.
CLOCK SET (setting the clock)
1 Press M.C. to display the setting mode. 2 Press M.C. to select the segment of the clock
display you wish to set. HourMinute
3 Turn M.C. to adjust the clock.
AUX (auxiliary input)
Activate this setting when using an auxiliary de­vice connected to this unit.
1 Press M.C. to turn AUX on or off.
USB (plug and play)
This setting allows you to switch your source to USB/iPod automatically. 1 Press M.C. to turn the plug and play function
on or off. ON – When a USB storage device/iPod is con- nected, depending on the type of device, the source is automatically switched to USB/iPod when you turn on the engine. If you disconnect your USB storage device/iPod, this units source is turned off. OFF – When a USB storage device/iPod is con- nected, the source is not switched to USB/ iPod automatically. Please change the source to USB/iPod manually.
SW CONTROL (rear output and subwoofer set­ting)
The rear speaker leads output and RCA output can be used for full-range speaker or subwoofer connection. If you switch to REAR-SP :SW,you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp. Initially, REAR-SP is set for rear full-range speaker connection (FUL).
1 Press M.C. to display the setting mode. 2 Turn M.C. to change the output and press to
select.
REAR-SPPREOUT
3 Turn M.C. to change the setting.
REAR-SP: FULSW PREOUT: SWREA
! Even if you change this setting, there will
be no output unless you turn the sub­woofer output on (refer to SUBWOOFER1 (subwoofer on/off setting) on this page).
! If you change this setting, subwoofer out-
put in the audio menu will return to the fac­tory settings.
DEMO (demo display setting)
1 Press M.C. to turn the demo display on or off.
SCROLL (scroll mode setting)
When ever scroll is set to ON, recorded text infor­mation scrolls continuously in the display. Set to OFF if you prefer the information to scroll just once. 1 Press M.C. to turn the ever scroll on or off.
Using an AUX source
1 Insert the stereo mini plug into the AUX input jack.
2 Press S (SRC/OFF) to select AUX as the source.
Note
AUX cannot be selected unless the auxiliary set­ting is turned on. For more details, refer to AUX (auxiliary input) on this page.
Turning the clock display on or off
% Press to turn the clock display on or off.
# The clock display disappears temporarily when you perform other operations, but the clock display appears again after 25 seconds.
9
En
y
4
5
h
Section
03
Installation
Installation
Connections
WARNING
! Use speakers over 50 W (output value) and
between 4 W to 8 W (impedance value). Do not use 1 W to 3 W speakers for this unit.
! The black cable is ground. When installing
this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly con­nected to metal parts of the car s body. The ground wire of the power amp and the one of this unit or any other device must be con­nected to the car separately with different screws. If the screw for the ground wire loos­ens or falls out, it could result in fire, genera­tion of smoke or malfunction.
Ground wire
Other devices (Another electronic device in the car)
Important
! When installing this unit in a vehicle without
an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.
ACC position No ACC position
10
En
POWER AMP
Metal parts of car’s bod
O
F
N
F
O
S
T
A
R
T
! Use this unit with a 12-volt battery and nega-
tive grounding only. Failure to do so may re­sult in a fire or malfunction.
! To prevent a short-circuit, overheating or mal-
function, be sure to follow the directions below.
Disconnect the negative terminal of the bat-
tery before installation.
Secure the wiring with cable clamps or adhe-
sive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring.
Place all cables away from moving parts,
such as the gear shift and seat rails.
Place all cables away from hot places, such
as near the heater outlet.
Do not connect the yellow cable to the battery
by passing it through the hole to the engine compartment.
Cover any disconnected cable connectors
with insulating tape.
Do not shorten any cables.Never cut the insulation of the power cable of
this unit in order to share the power with other devices. The current capacity of the cable is limited.
Use a fuse of the rating prescribed.Never wire the negative speaker cable directly
to ground.
Never band together negative cables of multi-
ple speakers.
! When this unit is on, control signals are sent
through the blue/white cable. Connect this cable to the system remote control of an ex­ternal power amp or the vehicles auto-anten­na relay control terminal (max. 300 mA 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal.
! Never connect the blue/white cable to the
power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction.
This unit
1
1 Power cord input 2 Rear output or subwoofer output 3 Front output 4 Antenna input 5 Fuse (10 A)
2 3
Power cord
Perform these connections when not connect­ing a rear speaker lead to a subwoofer.
LR
4
F
5
R
1
32
8
6
9
7
a
b
e f
g
c d
Perform these connections when using a sub­woofer without the optional amplifier.
LR
4
F
i
SW
1 To power cord input 2 Left 3 Right 4 Front speaker 5 Rear speaker 6 White 7 White/black 8 Gray 9 Gray/black a Green b Green/black c Violet d Violet/black e Black (chassis ground)
Connect to a clean, paint-free metal location.
f Yellow
Connect to the constant 12 V supply termi­nal.
g Red
Connect to terminal controlled by ignition switch (12 V DC).
h Blue/white
Connect to system control terminal of the power amp or auto-antenna relay control ter­minal (max. 300 mA 12 V DC).
i Subwoofer (4 Ω)
1
8
6
9
7
a
c d
b
j
e
a
f g
k l
h
b
32
c
d
Installation
j When using a subwoofer of 70 W (2 Ω), be
sure to connect the subwoofer to the violet and violet/black leads of this unit. Do not connect anything to the green and green/ black leads.
k Not used. l Subwoofer (4 Ω)× 2
Notes
! With a 2 speaker system, do not connect any-
thing to the speaker leads that are not con­nected to speakers.
! Change the initial setting of this unit. Refer
to SW CONTROL (rear output and subwoofer setting) on page 9. The subwoofer output of this unit is monau­ral.
Power amp (sold separately)
Perform these connections when using the op­tional amplifier.
2

2

3
55
3
77
4
6
1
1
1 System remote control
Connect to Blue/white cable.
2 Power amp (sold separately) 3 Connect with RCA cables (sold separately) 4 To Rear output or subwoofer output 5 Rear speaker or subwoofer 6 To Front output 7 Front speaker
Installation
Important
! Check all connections and systems before
final installation.
! Do not use unauthorized parts as this may
cause malfunctions.
! Consult your dealer if installation requires
drilling of holes or other modifications to the vehicle.
! Do not install this unit where:
it may interfere with operation of the vehicle.it may cause injury to a passenger as a result
of a sudden stop.
! The semiconductor laser will be damaged if
it overheats. Install this unit away from hot places such as near the heater outlet.
! Optimum performance is obtained when the
unit is installed at an angle of less than 60°.
60°
DIN front/rear mount
This unit can be properly installed using either front-mount or rear-mount installation. Use commercially available parts when instal­ling.
DIN Front-mount
1 Insert the mounting sleeve into the dash­board.
For installation in shallow spaces, use the sup­plied mounting sleeve. If there is enough space, use the mounting sleeve that came with the ve­hicle.
Installation
2 Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.
1
2
1 Dashboard 2 Mounting sleeve
3 Install the unit as illustrated.
1
2
4
5
1 Nut 2 Firewall or metal support 3 Metal strap 4 Screw 5 Screw (M4 × 8)
# Make sure that the unit is installed securely in place. An unstable installation may cause skipping or other malfunctions.
3
DIN Rear-mount
1 Determine the appropriate position where the holes on the bracket and the side of the unit match.
2 Tighten two screws on each side.
1
2
1 Screw 2 Mounting bracket 3 Dashboard or console
! Use either truss (5 mm × 8 mm) or flush sur-
face (5 mm × 9 mm) screws, depending on
the bracket screw holes.
3
Removing the unit
1 Remove the trim ring.
1 Trim ring 2 Notched tab
! Releasing the front panel allows easier ac-
cess to the trim ring. ! When reattaching the trim ring, point the
side with the notched tab down.
Section
03
English
11
En
Appendix
Installation
Additional Information
2 Insert the supplied extraction keys into both sides of the unit until they click into place.
3 Pull the unit out of the dashboard.
Removing and re-attaching the front panel
You can remove the front panel to protect your unit from theft. Press the detach button and push the front panel upward and pull it toward you. For details, refer to Removing the front panel to
protect your unit from theft and Re-attaching the front panel on page 4.
Securing the front panel
The front panel can be secured with the sup­plied screw.
1
1 Screw
Troubleshooting
Symptom Cause Action
The display automatically returns to the ordinary dis­play.
The repeat play range changes un­expectedly.
A subfolder is not played back.
NO XXXX ap­pears when a display is changed (NO TITLE, for ex­ample).
The display is illuminated when the unit is turned off.
You did not per­form any opera­tion within about 30 sec­onds.
Depending on the repeat play range, the se­lected range may change when another folder or track is being selected or during fast forwarding/re­versing.
Subfolders can­not be played when FOLDER (folder repeat) is selected.
There is no em­bedded text in­formation.
Demo mode is on.
Perform operation again.
Select the repeat play range again.
Select another re­peat play range.
Switch the display or play another track/file.
! Press cancel demo mode. ! Turn off the demo display set­ting.
Symptom Cause Action
The unit is malfunction­ing. There is inter­ference.
You are using a device, such as a cellular phone, that transmits elec­tric waves near the unit.
Error messages
When you contact your dealer or your nearest Pioneer Service Center, be sure to note the error message.
Built-in CD Player
Message Cause Action
ERROR-11, 12, 17, 30
ERROR-10, 11, 12, 15, 17, 30, A0
ERROR-15 The inserted
to
ERROR-23 Unsupported
FRMT READ Sometimes
The disc is dirty. Clean the disc. The disc is
scratched. There is an elec-
trical or me­chanical error.
disc is blank
CD format
there is a delay between the start of playback and when you start to hear any sound.
Move electrical devices that may be causing the in­terference away from the unit.
Replace the disc.
Turn the ignition switch OFF and back ON, or switch to a differ­ent source, then back to the CD player.
Replace the disc.
Replace the disc.
Wait until the message disap­pears and you hear sound.
12
En
Additional Information
Appendix
Additional Information
English
Message Cause Action
NO AUDIO The inserted
SKIPPED The inserted
PROTECT Allthe files on
USB storage device/iPod
Message Cause Action
NO DEVICE When plug and
FRMT READ Sometimes
NO AUDIO There are no
disc does not contain any playable files.
disc contains DRM protected files.
the inserted disc are em­bedded with DRM.
play is off, no USB storage de­vice or iPod is connected.
there is a delay between the start of playback and when you start to hear any sound.
songs.
The connected USB storage de­vice has secur­ity enabled
Replace the disc.
Replace the disc.
Replace the disc.
! Turn the plug and play on. ! Connect a com­patible USB stor­age device/iPod.
Wait until the message disap­pears and you hear sound.
Transfer the audio files to the USB storage device and connect.
Follow the USB storage device in­structions to dis­able the security.
Message Cause Action
SKIPPED The connected
PROTECT Allthe files in
N/A USB The connected
USB storage de­vice contains files embedded with Windows Mediaä DRM 9/ 10
the USB storage device are em­bedded with Windows Media DRM 9/10
USB storage de­vice is not sup­ported by this unit.
Play an audio file not embedded with Windows Media DRM 9/10.
Transfer audio files not em­bedded with Windows Media DRM 9/10 to the USB storage de­vice and connect.
! Connect a USB Mass Storage Class compliant device. ! Disconnect your device and replace it with a compatible USB storage device.
Message Cause Action
CHECK USB The USB con-
nector or USB cable has short­circuited.
The connected USB storage de­vice consumes more than 500 mA (maximum allowable cur­rent).
The iPod oper­ates correctly but does not charge
Check that the USB connector or USB cable is not caught in some­thing or dam­aged.
Disconnect the USB storage de­vice and do not use it. Turn the ignition switch to OFF, then to ACC or ON and then connect only compliant USB storage devices.
Make sure the connection cable for the iPod has not shorted out (e.g., not caught in metal objects). After checking, turn the ignition switch OFF and back ON, or dis­connect the iPod and reconnect.
Message Cause Action
ERROR-19 Communication
ERROR-23 USB storage de-
failed.
iPod failure Disconnect the
vice was not for­matted with FAT12, FAT16 or FAT32
! Perform one of the following op­erations. –Turn the ignition switch OFF and back ON. –Disconnect the USB storage de­vice. –Change to a dif­ferent source. Then, return to the USB source. ! Disconnect the cable from the iPod. Once the iPod's main menu is displayed, re­connect the iPod and reset it.
cable from the iPod. Once the iPod's main menu is displayed, re­connect the iPod and reset it.
USB storage de­vice should be for­matted with FAT12, FAT16 or FAT32.
13
En
Appendix
Additional Information
Additional Information
Message Cause Action
ERROR-16 The iPod firm-
STOP There are no
NOT FOUND No related
ware version is old
iPod failure Disconnect the
songs in the current list.
songs
Update the iPod version.
cable from the iPod. Once the iPod's main menu is displayed, re­connect the iPod and reset it.
Select a list that contains songs.
Transfer songs to the iPod.
Handling guidelines
Discs and player
Use only discs that feature either of the following two logos.
Use 12-cm discs. Do not use 8-cm discs or an adapter for 8-cm discs.
Use only conventional, fully circular discs. Do not use shaped discs.
Do not insert anything other than a CD into the CD loading slot.
Do not use cracked, chipped, warped, or other­wise damaged discs as they may damage the play­er.
Unfinalized CD-R/CD-RW discs cannot be played back.
Do not touch the recorded surface of the discs.
Store discs in their cases when not in use.
Do not attach labels, write on or apply chemicals to the surface of the discs.
To clean a CD, wipe the disc with a soft cloth out­ward from the center.
Condensation may temporarily impair the player s performance. Let it rest for about one hour to ad­just to a warmer temperature. Also, wipe any damp discs off with a soft cloth.
Playback of discs may not be possible because of disc characteristics, disc format, recorded applica­tion, playback environment, storage conditions, and so on.
Road shocks may interrupt disc playback.
USB storage device
Connections via USB hub are not supported.
Do not connect anything other than a USB stor­age device.
Firmly secure the USB storage device when driv­ing. Do not let the USB storage device fall onto the floor, where it may become jammed under the brake or accelerator pedal.
Depending on the USB storage device, the follow­ing problems may occur.
! Operations may vary. ! The storage device may not be recognized. ! Files may not be played back properly. ! The device may generate noise in the radio.
iPod
Do not leave the iPod in places with high tempera­tures.
To ensure proper operation, connect the dock con­nector cable from the iPod directly to this unit.
Firmly secure the iPod when driving. Do not let the iPod fall onto the floor, where it may become jammed under the brake or accelerator pedal.
About iPod settings ! When an iPod is connected, this unit changes
the EQ (equalizer) setting of the iPod to off in order to optimize the acoustics. When you dis­connect the iPod, the EQ returns to the original setting.
! You cannot set Repeat to off on the iPod when
using this unit. Repeat is automatically changed to All when the iPod is connected to this unit.
Incompatible text saved on the iPod will not be dis­played by the unit.
DualDiscs
DualDiscs are two-sided discs that have a record­able CD for audio on one side and a recordable DVD for video on the other. Since the CD side of DualDiscs is not physically compatible with the general CD standard, it may not be possible to play the CD side with this unit. Frequent loading and ejecting of a DualDisc may result in scratches on the disc. Serious scratches can lead to playback problems on this unit. In some cases, a DualDisc may become stuck in the disc loading slot and will not eject. To prevent this, we recommend you refrain from using DualDisc with this unit. Please refer to the information from the disc man­ufacturer for more detailed information about DualDiscs.
Compressed audio compatibility (disc, USB)
WMA
File extension: .wma
Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to 384 kbps (VBR)
Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz
Windows Media Audio Professional, Lossless, Voice/DRM Stream/Stream with video: Not com­patible
MP3
File extension: .mp3
Bit rate: 8 kbps to 320 kbps (CBR), VBR
Sampling frequency: 8 kHz to 48 kHz (32 kHz, 44.1 kHz, 48 kHz for emphasis)
14
En
Additional Information
Appendix
Additional Information
English
Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3 tag Version 2.x is given priority over Version 1. x.)
M3u playlist: Not compatible
MP3i (MP3 interactive), mp3 PRO: Not compatible
WAV
File extension: .wav
Quantization bits: 8 and 16 (LPCM), 4 (MS ADPCM)
Sampling frequency: 16 kHz to 48 kHz (LPCM),
22.05 kHz and 44.1 kHz (MS ADPCM)
Supplemental information
Only the first 32 characters can be displayed as a file name (including the file extension) or a folder name.
This unit may not operate correctly depending on the application used to encode WMA files.
There may be a slight delay at the start of playback of audio files embedded with image data or audio files stored on a USB storage device that has nu­merous folder hierarchies.
Disc
Playable folder hierarchy: up to eight tiers (A prac­tical hierarchy is less than two tiers.)
Playable folders: up to 99
Playable files: up to 999
File system: ISO 9660 Level 1 and 2, Romeo, Joliet
Multi-session playback: Compatible
Packet write data transfer: Not compatible
Regardless of the length of blank sections be­tween the songs from the original recording, com­pressed audio discs play with a short pause between songs.
USB storage device
Playable folder hierarchy: up to eight tiers (A prac­tical hierarchy is less than two tiers.)
Playable folders: up to 500
Playable files: up to 15 000
Playback of copyright-protected files: Not compati­ble
Partitioned USB storage device: Only the first par­tition can be played.
There may be a slight delay when starting play­back of audio files on a USB storage device with numerous folder hierarchies.
CAUTION
Do not leave discs or a USB storage device in any place that is subject to high temperatures.
iPod compatibility
This unit supports only the following iPod models. Supported iPod software versions are shown below. Older versions may not be supported.
! iPhone 3GS (software version 3.1.2) ! iPhone 3G (software version 3.1.2) ! iPhone (software version 3.1.2) ! iPod nano 5th generation (software version
1.0.1)
! iPod nano 4th generation (software version
1.0.4)
! iPod nano 3rd generation (software version
1.1.3)
! iPod nano 2nd generation (software version
1.1.3)
! iPod nano 1st generation (software version
1.3.1)
! iPod touch 3rd generation (software version
4.0)
! iPod touch 2nd generation (software version
3.1.2)
! iPod touch 1st generation (software version
3.1.2)
! iPod classic 160GB (software version 2.0.3) ! iPod classic 120GB (software version 2.0.1) ! iPod classic (software version 1.1.2) ! iPod 5th generation (software version 1.3)
Depending on the generation or version of the iPod, some functions may not be available.
Operations may vary depending on the software version of iPod.
When using an iPod, an iPod Dock Connector to USB Cable is required.
A Pioneer CD-IU50 interface cable is also avail­able. For details, consult your dealer.
About the file/format compatibility, refer to the iPod manuals.
Audio Book, Podcast: Compatible
CAUTION
Pioneer accepts no responsibility for data lost on the iPod, even if that data is lost while this unit is used.
Sequence of audio files
The user cannot assign folder numbers and specify playback sequences with this unit.
Example of a hierarchy
01
02
 
03
04
 
05
Level 1 Level 2 Level 3 Level 4
Disc
Folder selection sequence or other operation may differ depending on the encoding or writing software.
USB storage device
Playback sequence is the same as recorded se­quence in the USB storage device. To specify the playback sequence, the following method is recommended. 1 Create a file name that includes numbers
that specify the playback sequence (e.g., 001xxx.mp3 and 099yyy.mp3).
2 Put those files into a folder. 3 Save the folder containing files on the USB
storage device.
However,depending on the system environment, you may not be able to specify the playback se­quence.
audio file
01 to 05: Folder number 1 to 6: Playback sequence
: Folder
: Compressed
15
En
Appendix
Additional Information
Additional Information
For USB portable audio players, the sequence is different and depends on the player.
Copyright and trademark
iTunes
Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.
MP3
Supply of this product only conveys a license for private, non-commercial use and does not con­vey a license nor imply any right to use this prod­uct in any commercial (i.e. revenue-generating) real time broadcasting (terrestrial, satellite, cable and/or any other media), broadcasting/ streaming via internet, intranets and/or other networks or in other electronic content distribu­tion systems, such as pay-audio or audio-on-de­mand applications. An independent license for such use is required. For details, please visit http://www.mp3licensing.com.
WMA
Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/ or other countries. This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc.
iPod & iPhone
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Made for iPodand Made for iPhonemean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respec­tively, and has been certified by the developer to meet Apple performance standards.
16
En
Apple is not responsible for the operation of this device or its compliance with safety and regula­tory standards.
HD Radioä Technology
HD Radio Technology manufactured under li­cense from iBiquity Digital Corporation. U.S. and Foreign Patents. HD Radioä and the HD, HD Radio, and Arclogos are proprietary trade­marks of iBiquity Digital Corp.
Specifications
General
Power source ................... 14.4 V DC (10.8 V to 15.1 V al-
Grounding system ............ Negative type
Maximum current consumption
................................... 10.0 A
Dimensions (W × H × D):
DIN
Chassis .............. 178 mm × 50 mm × 165
Nose .................. 188 mm × 58 mm × 17
D
Chassis .............. 178 mm × 50 mm × 165
Nose .................. 170 mm × 46 mm × 17
Weight ............................. 1.2 kg (2.64 lbs)
Audio
Maximum power output ... 50 W × 4 Continuous power output
................................... 22 W × 4 (50 Hz to 15 000 Hz,
Load impedance .............. 4 W (4 W to 8 W allowable)
Preout maximum output level
................................... 2.0 V
Tone controls:
Bass
Frequency .......... 100 Hz
Gain .................. ±12 dB
Mid
Frequency .......... 1 kHz
Gain .................. ±12 dB
Treble
Frequency .......... 10 kHz
Gain .................. ±12 dB
Subwoofer (mono):
Frequency ................. 50/63/80/100/125 Hz
Slope ........................ –18 dB/oct
Gain ......................... +6 dB to –24 dB
Phase ....................... Normal/Reverse
lowable)
mm (7 in. × 2 in. × 6-1/2 in.)
mm (7-3/8 in.× 2-1/4 in.× 5/8 in.)
mm (7 in.× 2 in.× 6-1/2 in.)
mm (6-3/4 in.× 1-3/4 in.× 5/8 in.)
5 % THD, 4 W load, both chan­nels driven)
CD player
System ............................ Compact disc audio system
Usable discs .................... Compact disc
Signal-to-noise ratio ......... 94 dB (1 kHz) (IHF-A network)
Number of channels ........ 2 (stereo)
WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch
MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3
WAV signal format ........... Linear PCM & MS ADPCM
USB
USB standard specification
................................... USB 2.0 full speed
Maximum current supply
................................... 500 mA
USB Class ....................... MSC (Mass Storage Class)
File system ....................... FAT12, FAT16, FAT32
WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch
MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3
WAV signal format ........... Linear PCM & MS ADPCM
FM tuner
Frequency range .............. 87.9 MHz to 107.9 MHz
Usable sensitivity ............. 9 dBf (0.8 µV/75 W,mono, S/N:
Signal-to-noise ratio ......... 80 dB (digital broadcasting)
Signal-to-noise ratio ......... 72 dB (analog broadcasting)
AM tuner
Frequency range .............. 530 kHz to 1 710 kHz
Usable sensitivity ............. 25 µV (S/N: 20 dB)
Signal-to-noise ratio ......... 80 dB (digital broadcasting)
Signal-to-noise ratio ......... 62 dB (analog broadcasting)
audio) (Windows Media Player)
(Non-compressed)
audio) (Windows Media Player)
(Non-compressed)
30 dB)
(IHF-A network)
(IHF-A network)
(IHF-A network)
(IHF-A network)
Loading...
+ 36 hidden pages