Pioneer CB-130 Owners manual
STEREO
RACK
CElrlSO
EEtrlSE|\IV
Top
board
SPECIFICATIONS
Left side board
you
Thank
CB-130
to accommodate
ponents
this
is
two
they
CB-130
CB-130W
o
o
o
o
o
r
The
parts
The
assembly
and
Assembly
applicable
models are
differ
Before
carpet
ble the
or the rack.
Provide
screwdriver
Some
Wear
carefully.
Assemble
Make sure that all
sufficiently since
ponents
CHECKING
names and
list.
names and
purchasing
for
CB-130W
well as
as
Guide before assembly.
both CB-l30
to
exactly
in design
only
proceeding
or old blanket
rack
so
yourself
and a
parts
of the
gloves
to assemble
rack in
the
will be brought
quantities
that
Check
shapes
procedure
Pioneer audio
this
racks which are
stereo
are
the SYSCOM
options
same
as
.
.
with
on the
not to mark or scratch
as
with a medium-sized
large-sized
heavy
are
accordance
the screws and
the whole
PARTS
THE
the
all
of the
should
and
Gl or
records.
and
and CB-130W
with respect to
mentioned
Rose
wood
Walnut
. .
rack assembly, spread
the
floor
flat
bladed screwdriver.
others
and
the rack and
with the instructions.
weight of
of the
parts
parts
thus
on the rack.
parts
are
to bear
This Assembly
vinyl chloride
vinyl
where
present.
be
Right side
Record support
.-Caster
product.
designed
GllW
stereo
read through
Please
models.
assembly
below.
chloride
you
will assem-
either the
Phillips
have
sharp
handle the
nuts are
are
are
remembered.
tightened
the
stereo
shown
required
board
The
com-
Guide
The
but
coated.
coated.
a
floor
head
edges.
parts
com-
in the
for the
Cabinet
Dimensions:
Weight:
PARTS
taining
Cable clips
For
cord and connecting cords
material
NOTE:
Specifications and
notice
due to improvements.
and surface finish:
Particle
500(W) x
19-11/16(W)
17 kg
boards with
836(H)x 394(D)
(.37
lb
design subject to
LIST
PartlApplication
pin
Fixed
For fixing the top board,
side boards and shelf
board
Clamp
For fixing the top board,
side boards and shelf
board
Cabinet
For fixing the bottom
board
Rear
screws
For
Hexagonal
For
Clamp
For
holes
retaining
board
fixing the rear board
securing
screws
bundling the
cover
concealing the clamp
after
screws
mounting
wrench
cabinet
power
assembly
key
re-
polyvinyl
mm
x
32-15/16(H)
7
oz!
possible
Ouantity Physical
6
6
4
7
1
2
x 15-1/2(D) in
modification without
2
chloride
outline
@
F*
0
finish.
(D
rrtoNeeR'
ASSEMBLY
PROCEDURE
This rack
shelf
has
board
a shelf
cannot
fully assembled.
mounting
the
mine
sary
with step
1
Example
board.
re-positioned
be
Refer to
position
View
1
The mounting
once
the examples
of shelf
from
board.
side
Example
position
rack
the
below
This is
1st
2nd
2
of the
has been
deter-
and
neces-
Left
board
ATTACH THE CASTERS ONTO
BOTTOM
BOARD
fl-cu,t"'
MOUNTING
BOTTOM BOARD
BOARD
side-r........_
THE
LEFT
AND
THE
SIDE BOARD,
SHELF
ATTACH
CASTERS
Attach
side boards.
the
o
Left side
board
fixed
pins
@
Right
FIXED
THE
onto the top
side
board
PINS AND
board
(Example
1st
-2nd
{Example
Top board
and
Fixed
left and
2)
1)
pin
THE
right
Bottom board
MOUNTING
THE
Shelf
RIGHT
board
SIDE
Mounting
as left
Right
BOARD
method
is
side
side
board
Loading...