Pioneer BR-360 User Manual

Operating Instructions

REMOTE CONTROL

BR-360

2265 East 220th Street Long Beach, CA 90810 USA telephone: (310) 952-2111 http://www.pioneerbroadband.com

‹C 029 AACA›

What it does

The BR-360 operates all Pioneer V1000/BD-V3000 series Digital Home Terminals, as well as some home terminal models from other manufacturers. You need the BR-360 to experience all the viewing options Voyager offers, because you can’t access all Voyager functions from the Home Terminal front panel keys or from other brand remotes.

The BR-360 also supports basic remote control functions for nearly all TVs, VCRs, stereo receivers/ amplifiers, and some DVD players. You don’t have to remember to switch “modes” with the BR-360 each key always transmits to one device.

This instruction sheet contains setup instructions and device codes. Keep this sheet in case you need to set up the BR-360 remote again in the future.

Voyager

BD-

Batteries

Two AA batteries power the BR-360.

To install batteries:

1 Push the battery cover tab

toward the center, and lift the cover off.

2 Insert two fresh AA

batteries, in the directions shown inside the battery compartment.

3 Replace the battery

–

cover.

–

BR-360 keypad

The BR-360 operates your Voyager Home Terminal, TV, VCR, and audio equipment (stereo receiver/ amplifier).

devices.

make them easier to locate. Each key is described below. These are basic

descriptions only. Refer to the manual(s) that came with your Home Terminal to learn how to use the keys.

The device(s) in parentheses are those the key will operate. For example, note that item 18 below

—

(CH +/–) will change the channel on the Voyager terminal only, not on the TV or the VCR. Before you can use the BR-360 to operate your TV and other equipment, see Programming your BR-360 below to learn how to set up the BR-360.

Note:

operate with some versions of home terminal hardware or software.

Indicator

(1) Indicator light

Power control

(2) AUD, TV, CBL, VCR: Device power keys

On-screen operations

(3) MENU: Main menu access key

(4) INFO: Information key

(5) GUIDE: Interactive program guide key

(6) 5 , 4 , 6 , 3: Display navigation

(7) SELECT: Display action key

(8) PAGE +/–: Page rocker key

(9) SETTINGS: Voyager settings menu key

Certain keys only operate certain

Keys that work together are clustered to

Some keys designated “Voyager” may not

Blinks when the remote transmits a command. Also helps you during setup.

(Audio, TV , V oyager , VCR/DVD player)

Turn power of these devices on/off.

(Voyager)

Displays the menu of Voyager features.

(Voyager)

Displays information about the program currently playing or highlighted in the program guide.

(Voyager)

Displays the program guide listings.

keys

(Voyager)

Highlight an item from the on-screen choices.

Activates the highlighted item.

Accesses pages above or below the information currently displayed.

(Voyager)

Displays the menu of preferences for your Voyager home terminal.

(Voyager)

(10) EXIT: Exit key

Hides all on-screen graphics and returns you to regular TV viewing.

(11) HELP: Help access key

Displays helpful information about Voyager operation.

(12) A, B, C: Function keys

Make direct selections from on-screen menus.

(Voyager)

(13) DAY +/–: Program guide day skip keys

(Voyager)

Skip forward or backward a whole day in the program guide.

Channel/volume control

(14) FAV: Favorite channel recall key

(Voyager)

Tunes channels previously stored in the Voyager terminal’s favorite channel memory.

(15) LAST: Last channel recall key

(Voyager)

Accesses the previously tuned channel.

(16) MUTE: Mute key

(Audio, TV, or

Voyager)

Silences the audio. Press to activate. Press this key again to restore sound to the previous level.

(17) VOL +/–: Volume rocker key

(Audio, TV,

or Voyager)

Raises or lowers the sound level.

(18) CH +/–: Channel rocker key

Selects the next higher or lower channel.

(19) 0 – 9: Numeric keys

Directly tune channels by number. Also make numeric entries in on-screen menus.

(20) ENTER: Enter key

Immediately tunes the channel number you’ve just entered.

(Voyager)

BR-360 programming

(21) SETUP: BR-360 setup key

Starts programming your BR-360.

VCR/DVD/VOD operations (22) 7,4, 8, <, ;: Transport k e ys

(VCR, DVD player, or Voyager)

Activate play (4), rewind (7), fastforward (

8), stop (<), and pause (;)

functions of your VCR or DVD player. Take the same actions on Video-On-Demand programming through the Voyager terminal. Determined by position of VCR/ VOD toggle switch (24).

(23) = : Record key

Starts recording on your VCR.

(VCR)

(24) VCR/VOD: VCR/VOD toggle switch

Selects the device to which the BR-360 transport keys (22) transmit. Slide to “VCR” to send transport/pause commands to your VCR or DVD player. Slide to “VOD” to pause, scan forward/backward, stop, and resume play of a current Video-OnDemand program.

(25) TV/VCR: TV/VCR key

Toggles the VCR’s TV/VCR switch.

(VCR)

RF Bypass control

(26) BYPASS: RF Bypass key

Toggles the Voyager’s optional RF Bypass switch.

(Voyager)

Programming your BR-360

Setup for Voyager Home Terminal

No setup is required. The BR-360 is ready to run the Voyager Home T erminal.

Setup for TV operation

Find your TV brand and its three-digit codes under TV setup codes on the back of this sheet. If your brand is not listed, go to Searching the code

library instead. 1 Turn on the TV.

Press and hold

on. Keep holding until the light goes off.

3 Release 4 Press TV. 5 Enter the three-digit code. Indicator light

blinks twice to confirm acceptance.

6 Point the BR-360 toward the TV. 7 Press TV.

Yes:

No: Try setup again starting from step 2,

My TV setup code is:

Setup for VCR or DVD player operation

You can choose to control either your VCR or your DVD player. For VCR setup, find the VCR brand and its three-digit codes under VCR setup codes on the back of this sheet. If your brand is not listed, go to

Searching the code library. 1 Turn your VCR on.

SETUP.

The indicator light comes

SETUP.

The indicator light blinks once.

Did the TV turn off?

Setup complete.

digit setup code below for future reference.

using the next code listed for your brand. If you’ve tried all codes for your brand without success, use the method under Searching the code

library.

Write down the three-

2 Press and hold SETUP. The indicator light

comes on. Keep holding until the light goes off.

3 Release SETUP. The indicator light blinks

once.

4 Press VCR. 5 Enter the three-digit code. Indicator light

blinks twice to confirm acceptance.

6 Point the BR-360 toward the VCR. 7 Press VCR.

Yes:

No: Try setup again starting from step 2,

For DVD player setup, find your DVD player brand and its three-digit codes under DVD player setup codes on the back of this sheet. Then follow the above VCR instructions using your DVD player and code.

Did the V CR turn of f?

Setup complete.

three-digit setup code below for future reference.

using the next code listed for your brand. If you’ve tried all codes for your brand without success, try the method under Searching the code

library.

Write down the

My VCR or DVD player setup code is:

Setup for stereo receiver/amplifier operation

Find the audio equipment brand and its threedigit codes under Stereo receiver/amplifier setup codes on the back of this sheet. If your brand is not listed, go to Searching the code

library. 1 Turn your receiver (or amplifier) on. 2 Press and hold SETUP. The indicator light

comes on. Keep holding until the light goes off.

3 Release SETUP. The indicator light blinks

once.

4 Press AUD. 5 Enter the three-digit code. Indicator light

blinks twice to confirm acceptance.

6 Point the BR-360 toward the receiver. 7 Press AUD.

Yes:

No: Try setup again starting from step

Did the receiver turn off?

Setup complete.

three-digit setup code below for future reference.

2, using the next code listed for your brand. If you’ve tried all codes for your brand without success, try the method under

Searching the code library.

Write down the

My receiver/amplifier setup code is:

Searching the code library

If none of the codes on this sheet seem to work, or your brand is not listed, you can search the BR360 code library for one that works. The BR-360 automatically selects the proper code for your TV, VCR, or receiver/amplifier. Make sure the equipment is turned on before you program the BR-360.

To search the library of TV codes:

1 Turn on the TV.

Press and hold SETUP. The indicator light

comes on. Keep holding until the light goes off.

3 Release SETUP. The indicator light blinks

once.

4 Press TV. 5 Point the remote control at your TV and

press SELECT. The indicator light stays on.

Did the TV turn off?

Yes: Immediately press TV . The light

goes out and then blinks twice. Setup is complete. To make sure programming was done correctly, aim the remote at the TV and press TV . The TV should turn back on.

Note:

Now, be sure to follow Getting your code, to find out the three-digit setup code. Write it down so you can use the direct setup method in the future.

No: Repeat step 5 until the TV turns off.

You may need to do this over 100 times to go through the entire code library. Pause one second between each SELECT keypress.

Note:

If you accidentally went past the right code, press 6 to go backward through the library.

To search the library of VCR, DVD, or stereo receiver/amplifier codes:

Follow the steps above, but substitute “VCR” or “AUD” for “TV” in each step.

Getting your code

If you’ve used the Searching the code library method to program your BR-360, or if you’ve misplaced your setup code, you can find out the loaded TV, VCR/DVD and AUD codes.

To get the TV code:

Press and hold SETUP. The indicator light comes on. Keep holding until the light goes off.

2 Release SETUP. The indicator light blinks

once.

3 Press TV. 4 Press INFO. The indicator light blinks out

the code number in sequence. Count the number of blinks for each digit. The indicator light pauses between each digit.

Note:

A long blink means the digit is 0 (zero).

5 Write down the code for future reference

under Setup for TV operation.

To get the VCR/DVD or stereo receiver/amplifier code:

Follow the steps above, but substitute “VCR” or “AUD” for “TV” in step 3. Write down the code for future reference, under Setup for VCR or DVD

player operation, or Setup for stereo receiver/ amplifier operation.

Setting up volume control

The BR-360 comes to you ready to control volume and mute functions through the Voyager Home T erminal. You can set up the BR-360 to do these through the TV or stereo receiver/amplifier instead.

To switch volume/mute control to the TV, the receiver/amplifier, or back to the Voyager Home Terminal:

Press and hold on. Keep holding until the light goes off .

2 Release

SETUP

. The indicator light comes

SETUP

. The indicator light blinks once. 3 Press VOL+ or VOL–. The light blinks. 4 Press the key for the device on which you

want to control volume:

AUD: receiver/amplifier CBL: Voyager TV: TV set

The indicator light blinks twice. The BR-360 volume and mute keys now control volume on the new device.

5 To make sure programming was done

correctly, aim the BR-360 at the device and press VOL +, VOL –, or MUTE. The volume setting on the device should change.

Helpful hints

Setup

If the BR-360 does not operate the TV, VCR/DVD player, or stereo receiver properly:

1 Try all the codes listed for the device. 2 Try the search method.

Many devices use similar remote control codes. You may have selected a similar code for which only some commands work. Select another code from the list, or start the Searching the code library method over. Repeat the process until you find the correct code that operates all applicable functions for your equipment.

Note:

Remember, each key transmits to only one

device. See the BR-360 keypad section.

Operation

If the red indicator light does not blink when you press a key, or if the operation is intermittent:

Make sure the batteries are inserted correctly. Replace both batteries with two new AA batteries. Always replace both batteries at the same time.

TV setup codes

Akai — 030, 068, 071 Alba — 111 A-Mark — 118 Amstrad — 031 Anam — 009, 039, 118, 119, 135 Anam National — 142 AOC — 005, 006, 018, 019, 118,

139, 156

Archer — 118 Audiovox — 11 8 Bauer — 109 Baycraft — 034 Brockwood — 139 Broksonic — 060, 135 Candle — 006, 020, 021, 023,

034, 139

Candle/Citizen — 135, 156 Capehart — 018, 139 Circuit City — 139 Citizen — 006, 015, 020, 021,

022, 023, 024

Colortyme — 071, 139 Concerto — 021 Contec — 025, 026, 039, 089 Contec Cony — 135 Craig — 034, 039, 135, 138 Crown — 024, 034 Curtis Mathes — 006, 015, 024,

071, 147, 156

CXC — 039, 135 Daewoo — 005, 022, 024, 027,

028, 029, 030, 142, 156, 163

Daytron — 024, 139 Dixi — 030, 086, 118 Dumont — 139 Electrohome — 024, 071, 153,

157

Elta — 030 Emerson — 024, 025, 026, 031,

032, 033, 034, 035, 036, 037, 038, 039, 071, 120, 135, 136, 139, 140, 143, 164

Envision — 006, 156 Etron — 030 Fisher — 040, 088 Formenti — 109 Fortress — 071, 103 Fujitsu — 032, 138 Funai — 032, 039, 135, 138 Futuretech — 039, 135, 138 GE — 003, 008, 009, 014, 038,

041, 042, 128, 139, 142, 145, 158, 159, 160

Genexxa — 111 Goldstar — 005, 021, 024, 043,

044, 071, 086, 137, 156

Gradiente — 155 Granada — 139, 155 Grand — 139 Grundig — 045 Hallmark — 139 Harman/Kardon — 059 Hinari — 032 Hitachi — 021, 024, 046, 047,

048, 049, 050, 051, 052, 053, 083, 095, 124, 146, 162

Infinity — 064 JBL — 064 JC Penney — 003, 005, 006,

015, 024, 029, 041, 094, 145, 158

Jensen — 054, 071 JVC — 055, 056, 057, 058 Kawasho — 046, 059, 156 Kenwood — 006, 071, 156 Kloss — 020, 059, 108 Kloss Novabeam — 142 KTV — 024, 037, 038, 039, 135,

140, 156

Lloyds — 139 Lloytron — 024 Loewe — 086 Logik — 017 Luxman — 021 LXI — 003, 061, 064, 088, 093,

115, 123, 145

Magnasonic — 071 Magnavox — 006, 019, 023,

034, 062, 063, 064, 065, 066, 067, 071, 073, 108, 154, 156

Marantz — 006, 064, 071, 086,

156

Matsui — 030, 107 Megatron — 139 Memorex — 017, 030, 088, 139 MGA — 004, 005, 006, 069,

071, 139

Mitsubishi — 004, 005, 068,

069, 070, 095, 121, 139, 149, 151, 156

Montgomery Ward — 005, 006,

014, 017, 032, 034, 041, 062, 063, 065, 066, 105, 117, 156, 158, 159

MTC — 005, 006, 015, 021, 029,

139, 156

NAD — 000, 115, 139 National — 009, 141 National Quenties — 141 NEC — 005, 006, 007, 016, 021,

071, 125, 156

Nikkai — 110, 111, 116 Nordmende — 049 Normandic — 161 Novabeam — 059 Nyon — 145 Onwa — 039, 135 Optonica — 103, 105 Orion — 138 Osaki — 110 Panasonic — 008, 009, 010, 011,

012, 064, 072, 133, 141, 142, 144, 150, 158, 160

Philco — 005, 006, 023, 034,

062, 063, 066, 071, 108, 156

Philips — 064, 086 Pioneer — 000, 046, 049, 074,

152

Portland — 005, 024, 156 Proscan — 003 Proton — 013, 018, 024, 034,

083, 122, 139

Pulsar — 002 Quasar — 008, 009, 075, 142,

144

Radio Shack — 024, 039, 105,

110, 135, 142

RCA — 003, 005, 014, 046, 077,

078, 079, 080, 081, 082, 084, 085, 123, 131, 132, 135, 142, 145, 152, 158, 159, 160

Realistic — 088 Saba — 049 Saisho — 030, 031, 107 Sampo — 006, 018, 142 Samsung — 005, 006, 015, 021,

024, 030, 086, 110, 139, 148, 156, 165

Samwon — 118 Sanyo — 040, 087, 088, 089,

090, 107

SBR — 086 Schneider — 086 Scott — 024, 032, 035, 039,

091, 098, 135, 140, 145

Sears — 003, 021, 032, 040,

061, 087, 088, 092, 093, 094, 096, 097, 099, 100, 101, 102, 115, 139, 147

Seimitsu — 139 Sharp — 024, 083, 089, 103,

104, 105, 106, 126, 127

Siemens — 089 Signature — 017 Silver — 071 Solavox — 110 Sony — 001, 076, 107, 117, 120,

134

Soundesign — 023, 034, 039,

135, 139

Spectricon — 019, 118 Squareview — 138 SSS — 005, 039, 071, 135, 156 Supra — 021 Supre-Macy — 020 Sylvania — 006, 023, 034, 062,

063, 064, 066, 071, 073, 098, 108, 109, 156

Symphonic — 130, 136, 138 Tandy — 103, 111 Tatung — 009, 142 Technics — 008 Techwood — 021, 071 Teknika — 004, 005, 015, 017,

020, 021, 022, 023, 024, 032, 034, 039, 112, 113, 135, 156

Teleavia — 049 Telefunken — 049 Teletech — 030 Tera — 013 Thomas — 139 Thomson — 049, 114, 153 TMK — 021, 071, 139 Toshiba — 015, 088, 094, 115,

116, 129

Tosonic — 026 Totevision — 024 Toyomenko — 139 Universal — 041 Vector Research — 006 Victor — 055 Video Concepts — 068, 135 Vidtech — 005, 139, 156 Viking — 020 Yamaha — 005, 006, 156 York — 139 Zenith — 002, 017, 137 Zonda — 118

VCR setup codes DVD player setup

Aiwa — 088, 119, 120, 121 Akai — 017, 018, 019, 020, 021,

022, 023, 024, 072

Alba — 050 Amstrad — 088 ASA — 069 Audio Dynamics — 094, 100 Broksonic — 063 Bush — 089 Candle — 080, 092, 093 Canon — 046, 057, 058 Capehart — 047, 050 Citizen — 091, 092, 093 Craig — 091, 108 Crosley — 057 Curtis Mathes — 058, 092, 105 Daewoo — 038, 049, 050, 051,

093

Daytron — 050 DBX — 094, 100 Dumont — 053 Dynatech — 088 Electrohome — 109 Emerson — 009, 010, 011, 012,

013, 014, 015, 016, 063, 072, 088, 090, 109, 116

Finlandia — 053 Finlux — 053, 069, 088 Fisher — 052, 053, 084, 088,

108, 110

GE — 054, 055, 056, 058, 076,

091, 105

Go Video — 061, 062, 117 Goldstar — 034, 059, 092, 112,

113

Goodmans — 085, 089 Granada — 053, 081 Grundig — 069 Harman Kardon — 034, 073 Hinari — 089 Hitachi — 040, 041, 042, 043,

044, 045, 057, 088, 095, 096, 097

Instant Replay — 057 ITT — 022 JC Penney — 034, 058, 080,

091, 094, 100, 101

Jensen — 064 JVC — 065, 066, 067, 068, 092,

094, 100, 101

Kenwood — 066, 081, 092, 094,

100, 101

Lloyds — 088 Logik — 089 Luxor — 022 Magnavox — 031, 057, 058, 060,

069, 111

Marantz — 034, 058, 069, 085,

092, 094, 100, 101, 103

MEI — 058 Memorex — 037, 053, 058, 070,

081, 085, 088, 108

MGA — 071, 072, 109 Mitsubishi — 066, 071, 072,

073, 074, 075, 109

Montgomery Ward — 031, 058,

080, 085, 088, 089, 090, 091, 107, 108, 109

MTC — 048, 080, 088 Multitech — 088, 089, 091 NAD — 000 NEC — 034, 035, 036, 066, 092,

094, 099, 100, 101, 102, 103, 104

Olympic — 057 Optonica — 085 Orion — 010, 011 Panasonic — 025, 026, 027, 028,

030, 057, 058, 098, 114, 123

Pentax — 041, 092 Perdio — 088 Philco — 057, 058, 111 Philips — 057, 058, 069, 085 Pioneer — 000, 001, 002, 003,

057, 066, 100

Portland — 050, 093 Proscan — 057, 105 Pulsar — 037 Quartz — 081 Quasar — 057, 058, 077, 078 Radio Shack — 107, 108, 109,

110

RCA — 029, 030, 031, 032, 033,

041, 091, 105, 106, 115, 124, 125

Realistic — 053, 058, 080, 081,

084, 085, 088

Ricoh — 006 Saisho — 010, 011 Salora — 071, 081 Samsung — 021, 038, 079, 080,

091

Sansui — 036, 048, 066, 100,

118

Sanyo — 053, 081, 082, 083,

108, 126

SBR — 069 Schneider — 089 Scott — 012, 063, 090 Sears — 052, 053, 081, 084,

108, 110

Sentra — 050 Sharp — 085, 107, 109, 122 Shintom — 089 Sony — 004, 005, 006, 007, 008 Sylvania — 057, 058, 060, 071,

088, 111

Symphonic — 088, 094 Tandy — 088 Tashiko — 088 Tatung — 086, 094, 101 Teac — 088, 094, 101 Technics — 057, 058 Teknika — 058, 087, 088 TMK — 010 Toshiba — 038, 039, 071, 090 Totevision — 080, 091 Unitech — 080 Vector Research — 034, 100 Victor — 065, 066, 100 Video Concepts — 072, 100 Videosonic — 091 Yamaha — 034, 092, 094, 100,

101

Zenith — 004, 005, 037

codes

Hitachi — 132 Magnavox — 130 Mitsubishi — 133 Pioneer — 129 RCA — 131 Sony — 128 Toshiba — 127

Stereo receiver/ amplifier setup codes

Aiwa — 004, 032, 033, 034,

035, 036, 037, 038

Carver — 020 Citizen — 023 Fisher — 020 GE — 025 Goldstar — 006 Hitachi — 031 JVC — 018, 039 Kenwood — 007, 040 Luxman — 003 Marantz — 022 Memorex — 008 NAD — 012 Nakamichi — 010 NEC — 030 Onkyo — 005, 015, 016 Optimus — 013 Panasonic — 021 Pioneer — 000, 001, 008, 046,

047

Proton — 028 Quasar — 021 RCA — 019, 027, 041 Scott — 017 Sharp — 026, 029 Sherwood — 011 Sony — 004, 009, 042, 043 Technics — 021 Toshiba — 024 Victor — 018 Yamaha — 002, 014, 044, 045