Pioneer AVD-W6200 User Manual
ENGLISH
ESPAÑOL
DEUTSCH FRANÇAIS
ITALIANO NEDERLANDS
16:9 Rear Seat Entertainment Display
Owner’s Manual
AVD-W6200
This product conforms to new cord colors.
Los colores de los cables de este producto se conforman con un nuevo
código de colores.
Dieses Produkt entspricht den neuen kabelfarben.
1
Contents
Contents ...................................................... 1
IMPORTANT SAFEGUARDS .................... 2
Please Read All of These Instructions
Regarding Your Display and Retain
them for Future Reference ........................ 2
Fitting and Removing the Display ............3
To fit the display ................................................3
To remove the display ........................................4
IMPORTANT INFORMATION .................... 5
About This Product .......................................... 5
Precaution .......................................................... 5
In Case of Trouble ............................................ 5
Before Using This Product ...................... 6
To Avoid Battery Exhaustion ............................ 6
To Protect the LCD Screen of the Display ........ 6
When Viewing is Difficult, use [BRIGHTNESS]
and [DIMMER] to Adjust .......................... 6
About the RCA Video and Audio Outputs
of this Unit....................................................6
To Ensure Safe Driving .................................... 7
Resetting the System ........................................ 8
-
Resetting the Microprocessor
-
Resetting the Setup Function
Key Finder .................................................... 9
Component Parts and Features .......................... 9
Basic Operation ...................................... 10
Turn On Power ................................................ 10
Volume Adjustment ........................................ 11
Selecting a Source ............................................ 11
Changing the Wide Screen Mode .................... 12
-
Wide Modes Available
Operating the Setup Function ................ 14
Dimmer Setting [DIMMER] .......................... 14
Entering the Setup Function ............................ 15
Functions to be set............................................ 15
-
Brightness [BRIGHTNESS]
-
Contrast [CONTRAST]
-
Color [COLOR]
-
Hue [HUE]
-
Location [LOCATION]
-
Speaker [SPEAKER]
-
Color System [COLOR SYSTEM]
Using the Display Correctly .................. 17
Handling the Display ...................................... 17
About the Liquid Crystal Display (LCD)
Screen ...................................................... 18
Keeping the Display in Good Condition ........ 18
About the Small Fluorescent Tube .................. 18
Connecting the System .......................... 19
Names and Functions of Connection
Terminals .................................................. 21
Connecting the Power Cable .......................... 22
Connection Diagram (VIDEO input) .............. 23
Connecting the RCA Audio and
Video Output ............................................ 24
Installation ................................................ 25
-
When the Display is Installed in the Front
Before Installing and Fixing ............................ 26
Before Affixing the Adhesive Tape ................ 26
Installing the Hide-away Unit ........................ 27
-
Installation Precautions
-
Hide-away Unit Installation
Specifications .......................................... 28
2
ENGLISH ESPAÑOL DEUTSCH FRANÇAIS
ITALIANO NEDERLANDS
IMPORTANT SAFEGUARDS
Please Read All of These Instructions Regarding Your Display
and Retain them for Future Reference
1. Read this manual fully and carefully before operating your display.
2. Keep this manual handy for future reference.
3. Pay close attention to all warnings in this manual and follow the instructions carefully.
4. Never allow others to use the system until they have read and understood the
operating instructions.
5. Do not install the display where it may (i) obstruct the driver’s vision, (ii) impair
the performance of any of the vehicle’s operating systems or safety features,
including airbags, or (iii) impair the driver’s ability to safely operate the vehicle.
6. As with any accessory in your vehicle’s interior, the display should not divert
your attention from the safe operation of your vehicle. If you experience difficulty in operating the system or reading the display, please park safely before making adjustments.
7. Do not attempt to install or service your display by yourself. Installation or servicing of the display by persons without training and experience in electronic
equipment and automotive accessories may be dangerous and could expose you
to the risk of electric shock or other hazards.
8. Please remember to wear your seat belt at all times while operating your vehicle.
If you are ever in an accident, your injuries can be considerably more severe if
your seat belt is not properly buckled.
9. If this product is installed in a place where it is visible to the vehicle’s driver, you
MUST always set the [LOCATION]to the [FRONT]setting. Failure to do so
could result in distracting images being potentially visible to the driver while the
vehicle is in motion.
If this product is installed in a place where it is not visible to the vehicle’s driver,
then you may choose the [REAR]location setting.
Use of this product is subject to any government laws regarding placement or use.
PIONEER does not accept any liability for any problems, damage or loss incurred
as a result of the product being used with an incorrect setting or in violation of
any government laws.
3
Fitting and Removing the Display
Note:
• The mounting arm described below is sold separately. For more information on the installation,
refer to the instruction manual or consult your nearest dealer.
To fit the display
1. Fit part 1 of the display into the grooves 2 of the base.
2. Slide the display until it clicks into place.
Precaution:
• To prevent failure, be sure to turn the ignition switch or system power OFF before fitting or
removing the display. Also take care not to grip the screen or buttons too firmly or to drop the
display.
• Do not let any water get on the terminals on the display or on the cable and do not allow the terminals to be shorted by a metal object or the like. This can cause system breakdown.
• Be careful not to touch terminals on the display or on the cable. Doing so may cause connection
failures. If any terminals are stained, wipe them with a clean dry cloth.
Base
Mounting arm
(sold separately)
Connect the cable to the
display.
4
ENGLISH ESPAÑOL DEUTSCH FRANÇAIS
ITALIANO NEDERLANDS
To remove the display
• Pull the lock release lever 3 and hold in that position, then slide the display and
detach it from its base.
• To prevent theft of the display, remove the display when leaving the vehicle.
Base
Mounting arm
(sold separately)
Press the lock release button
while holding the display.
Keep holding the button and
unplug the connector.
5
About This Product
• Do not place the display in a position where it will impede the driver’s visibility or
affect the operation of your vehicle’s airbags or headrests.
Precaution
• Always keep the volume low enough for outside sounds to be audible.
• Protect the product from moisture.
In Case of Trouble
Should this product fail to operate properly, contact your dealer or the nearest authorized
Pioneer service facility.
• This product complies with the EMC Directives (89/336/EEC, 92/31/EEC) and
CE Marking Directive (93/68/EEC).
IMPORTANT INFORMATION
To Avoid Battery Exhaustion
Always run the vehicle engine while using this unit. Using this unit without running the
engine can result in battery drainage.
To Protect the LCD Screen of the Display
• Do not allow direct sunlight to fall on the Display when this unit is not being used.
Extended exposure to direct sunlight can result in LCD screen malfunction due to the
resulting high temperatures.
• When using a portable phone, keep the antenna of the portable phone away from the
Display to prevent disruption of the video by the appearance of spots, colored stripes,
etc.
When Viewing is Difficult, use [BRIGHTNESS] and [DIMMER] to Adjust
Due to its construction, the view angle of the LCD screen is limited. The viewing angle
(vertical and horizontal) can be increased, however, by using [BRIGHTNESS] to adjust
the black density of the video. When using for the first time, adjust the black density in
accordance with the viewing angle (vertical and horizontal) to adjust for clear viewing.
[DIMMER] can also be used to adjust the brightness of the LCD screen itself to suit your
personal preference.
About the RCA Video and Audio Outputs of this Unit
When you connect a separate piece of AV equipment such as another display to the RCA
video and audio output jacks of the hide-away unit, you can select the source for output
with the SOURCE button.
• The video and audio source of the RCA outputs of this unit cannot be selected independently.
• Volume control buttons will have no effect even if operated.
CAUTION
Never position the display connected to the RCA output jack of the hideaway unit so that the driver can view the picture while the vehicle is moving.
6
ENGLISH ESPAÑOL DEUTSCH FRANÇAIS
ITALIANO NEDERLANDS
Before Using This Product
7
Before Using This Product
To Ensure Safe Driving
This unit senses whether the parking brake is on or off. When installed in the FRONT, it is
arranged so that video cannot be viewed while the vehicle is moving. The various settings
and adjustments are also not possible while driving. (The following message will be displayed on the screen while the vehicle is moving.)
Stop the vehicle in a safe place, apply the parking brake and wait for the message to clear
before starting operation.
Note:
• You cannot select wide mode while the message above is displayed on the screen. (Refer to page
12.)
8
ENGLISH ESPAÑOL DEUTSCH FRANÇAIS
ITALIANO NEDERLANDS
Resetting the System
Resetting the Microprocessor
Pressing the RESET button lets you reset the microprocessor to its initial settings without
changing the setup function settings.
Reset the microprocessor in the following cases:
When using this product for the first time after installation.
When the product fails to operate properly.
When strange (incorrect) messages appear on the display.
• To reset the microprocessor, press the RESET button on the unit with a pen
tip or other pointed instrument.
Resetting the Setup Function
The WIDE/MENU button and the RESET button let you erase all memorized settings and
return the setup function to their initial (factory) settings without resetting the microprocessor. (Refer to the next page.)
1. Hold the WIDE/MENU down and press the RESET button.
2. Release the RESET button and hold down the WIDE/MENU button for 2
seconds.
3. Release the WIDE/MENU button.
RESET button
Loading...