Pioneer AppRadio 2 (SPH-DA100) Installation Manual
Installation Manual
Manuel d’installation
SPH-DA100
AppRadio
English Français
Contents
01
Precautions
Your new display unit and this manual .........
Important safeguards ...................................
02
Connecting the system
Precautions before connecting
the system ................................................
Before installing this product ...........................
To prevent damage ........................................
₋
Notice for the blue/white lead .....................
Parts supplied ................................................
₋
Installing the HDMI holder ............................
Connecting the system ..................................
Connecting the power cord (1) .....................
Connecting the power cord (2) ..................
When connecting to separately sold
power amp/subwoofer............................
When connecting a rear view camera .......
3
3
4
4
5
5
6
6
7
8
10
11
12
03
Installation
Precautions before installation ..................
To avoid electromagnetic interference ......
Before installing .........................................
Installing this product ................................
₋
Installation notes .......................................
₋
Parts supplied ............................................
₋
Installation using the screw holes
on the side of this product .........................
Installing the GPS antenna ........................
₋
Installation notes .......................................
₋
Parts supplied ............................................
₋
When installing the antenna inside the
vehicle (on the dashboard or rear shelf) ....
Installing the microphone ..........................
₋
Parts supplied ............................................
₋
Mounting on the sun visor .........................
₋
Installation on the steering column ...........
₋
Adjusting the microphone angle ................
2
En
13
13
13
14
14
15
15
16
16
16
17
18
18
18
19
19
Precautions
Section
01
Your new display unit and
this manual
Do not operate this product, any applica-
•
tions, or the rear view camera option (if
purchased) if doing so will divert your attention in any way from the safe operation of
your vehicle. Always observe safe driving
rules and follow all existing traffic regulations. If you experience difficulty in operating this product or reading the display, park
your vehicle in a safe location and apply the
parking brake before making the necessary
adjustments.
Do not install this product where it may (i)
•
obstruct the driver’s vision, (ii) impair the
performance of any of the vehicle’s operating systems of safety features, including airbags, hazard lamp buttons, or (iii) impair
the driver’s ability to safely operate the
vehicle. In some cases, it may not be possible to install this product because of the
vehicle type or the shape of the vehicle
interior.
This manual explains how to install this
•
product in your vehicle. Operation of this
product is explained in the separate manuals.
Important safeguards
WARNING
Pioneer does not recommend that you install
this product yourself. We recommend that
only authorized Pioneer service personnel,
who have special training and experience
in mobile electronics, set up and install this
product. NEVER SERVICE THIS PRODUCT
YOURSELF. Installing or servicing this product and its connecting cables may expose
you to the risk of electric shock or other
hazards, and can cause damage to the product that is not covered by warranty.
Read this manual fully and carefully before
•
installing this product.
Keep this manual handy for future refer-
•
ence.
Pay close attention to all warnings in this
•
manual and follow the instructions carefully.
Traffic restrictions and advisories are always
•
more important than guidance given by a
third-party navigation/mapping smartphone application. Always obey current
traffic restrictions, even if the application
provides contrary advice.
As with any accessory in your vehicle’s inte-
•
rior, this product should not divert your
attention from the safe operation of your
vehicle. If you experience difficulty in operating this product or reading the display,
please make adjustments while safely
parked.
Please remember to wear your seat belt at
•
all times while operating your vehicle. If you
are in an accident, your injuries can be considerably more severe if your seat belt is
not properly fastened.
Certain country and government laws may
•
prohibit or restrict the placement and use
of this product in your vehicle. Please comply with all applicable laws and regulations
regarding the use, installation and operation of this product.
English
En
3
Section
02
Connecting the system
Precautions before
connecting the system
CAUTION
If you decide to perform the installation
•
yourself, and have special training and
experience in the mobile electronics
installations, please carefully follow all
of the steps in the installation manual.
•
Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.
•
Do not directly connect the yellow lead
of this product to the vehicle battery. If
the lead is directly connected to the
battery, engine vibration may eventually cause the insulation to fail at the
point where the wire passes from the
passenger compartment into the
engine compartment. If the yellow
lead’s insulation tears as a result of
contact with metal parts, short-circuiting can occur, resulting in considerable danger.
•
It is extremely dangerous to allow
cables to become wound around the
steering column or shift lever. Be sure
to install this product, its cables, and
wiring away in such so that they will
not obstruct or hinder driving.
•
Make sure that the cables and wires
will not interfere with or become
caught in any of the vehicle’s moving
parts, especially the steering wheel,
shift lever, parking brake, sliding seat
tracks, doors, or any of the vehicle’s
controls.
•
Do not route wires where they will be
exposed to high temperatures. If the
insulation heats up, wires may become
damaged, resulting in a short circuit or
malfunction and permanent damage to
the product.
Do not cut the GPS antenna cable to
•
shorten it or use an extension to make
it longer. Altering the antenna cable
could result in a short circuit or malfunction.
•
Do not shorten any leads. If you do, the
protection circuit (fuse holder, fuse
resistor or fi lter, etc.) may fail to work
properly.
•
Never feed power to other electronic
products by cutting the insulation of
the power supply lead of this product
and tapping into the lead. The current
capacity of the lead will be exceeded,
causing overheating.
Before installing this product
•
Use this unit with a 12-volt battery and negative grounding only. Failure to do so may
result in a fire or malfunction.
To avoid shorts in the electrical system, be
•
sure to disconnect the (−) battery cable
before installation.
4
En
Connecting the system
Section
02
To prevent damage
WARNING
Use speakers over 50 W (output value)
•
and between 4
value). Do not use 1
for this unit.
•
The black cable is ground. When
installing this unit or power amp (sold
separately), make sure to connect the
ground wire fi rst. Ensure that the
ground wire is properly connected to
metal parts of the car’s body. The
ground wire of the power amp and the
one of this unit or any other device
must be connected to the car separately with different screws. If the
screw for the ground wire loosens or
falls out, it could result in fi re genera-
tion of smoke or malfunction.
Ground wire Power amp
Other devices
(Another electronic
device in the car)
*1
Not supplied for this unit.
When replacing the fuse, be sure to
•
only use a fuse of the rating prescribed
on this product.
When disconnecting a connector, pull the
•
connector itself. Do not pull the lead, as
you may pull it out of the connector.
This product cannot be installed in a vehi-
•
cle without ACC (accessory) position on
the ignition switch.
O
Ω to 8 Ω (impedance
Metal parts of car’s body
C
C
A
O
F
N
F
S
T
A
R
T
Ω to 3 Ω speakers
O
F
N
F
O
S
T
A
R
T
To avoid short-circuiting, cover the discon-
•
nected lead with insulating tape. It is especially important to insulate all unused
speaker leads, which if left uncovered may
cause a short circuit.
Refer to the owner’s manual for details on
•
connecting the power amp and other units,
then make connections accordingly.
Since a unique BPTL circuit is employed, do
•
not directly ground the
speaker lead or connect the
side of the
side of
another side of the speaker lead together.
Be sure to connect the
side of the
speaker lead to the side of the speaker
lead on this product.
If the RCA pin jack on this product will not
•
be used, do not remove the caps attached
to the end of the connector.
Notice for the blue/white lead
•
When the ignition switch is turned on (ACC
ON), a control signal is output through the
blue/white lead. Connect to an external
power amp’s system remote control terminal (max. 300 mA 12 V DC). The control signal is output through the blue/white lead,
even if the AV source is switched off.
Be sure not to use this lead as the power
•
supply lead for the external power amps.
Such connection could cause excessive current drain and malfunction.
Be sure not to use this lead as the power
•
supply lead for the auto-antenna or
antenna booster. Such connection could
cause excessive current drain and malfunction.
English
ACC position No ACC position
En
5
Section
02
Connecting the system
Parts supplied
This product Power cord
GPS antenna iPhone cable
Microphone HDMI holder
Installing the HDMI holder
1 Insert the lower tab of the HDMI
holder into the groove of this product.
Groove
Tab
2 Insert the two upper tabs into the
this product by pushing the HDMI
holder.
Tab s
❐ Use the HDMI holder when you connect
this product with the separately sold
App Connectivity Kit (CD-AH200C).
❐ Never grip the holder tightly or use
force when removing or attaching.
6
En
Connecting the system
Section
02
Connecting the system
Microphone
iPhone cable
2.25 m
(7 ft. 5 in.)
4 m (13 ft. 1 in.)
This product
GPS antenna
3.55 m (11 ft. 8 in.)
HDMI cables (*2)
(sold separately)
Type A - A
HDMI holder
Wired remote input
Please refer to the instruction
manual for the Hard-wired remote
control adapter (sold separately).
Android™ device (*1)
Type A - D
Vehicle antenna
USB - micro USB cable (*2)
(sold separately)
English
Power supply box (*2)
iPhone or iPod with Dock Connector (*1)
(*1)
For details concerning operations and compatibility, refer to the Operation Manual.
(*2)
For details about how to connect the separately sold
App Connectivity Kit (CD-AH200C), refer to the App Connectivity Kit manual.
(sold separately)
WARNING
To avoid the risk of accident and the potential violation of applicable laws, this product should
•
never be used while the vehicle is being driven except for navigation purposes.
In some countries, the viewing of images on a display inside a vehicle even by persons other than
•
the driver may be illegal. Where such regulations apply they must be obeyed and this product’s
app-based content should not be used.
En
7
Section
02
Connecting the system
Connecting the power cord (1)
Yellow
To terminal supplied with power
regardless of ignition switch position.
Red
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
Note
When a subwoofer is connected to this
product instead of a rear speaker, change
the rear output setting in the initial setting.
(Refer to the Operation Manual.)
The subwoofer output of this product is
monaural.
With a two-speaker system, do not connect anything
to the speaker leads that are not connected to
speakers.
Front speaker
Left
Rear speaker or
subwoofer (4 Ω)
When using a subwoofer of 70 W (2 Ω), be sure to connect with the violet and violet/black leads of this product.
Do not connect anything with the green and green/black leads.
Not used.
8
En
Green
Green/black
White
White/black
Green
Green/black
Violet
Violet/black
Gray
Gray/black
Violet
Violet/black
Front speaker
Right
Rear speaker or
subwoofer (4 Ω)
Subwoofer (4 Ω) X 2
Connecting the system
This product
10
Section
02
English
Fuse (10 A)
Power cord
Blue/white
To auto-antenna relay control terminal.
If the vehicle has a glass antenna, connect to the antenna
booster power control terminal (max. 300 mA 12 V DC).
En
9
Section
02
Connecting the system
Connecting the power cord (2)
This product
Power cord
Light green (PARKING BRAKE)
Used to detect the ON/OFF status of the parking
brake. This lead must be connected to the power
supply side of the parking brake switch.
If this connection is made incorrectly or
omitted, certain functions of this product
will be unusable.
Violet/white (REVERSE GEAR SIGNAL INPUT)
This is connected so that the this product can detect
whether the vehicle is moving forwards or backwards.
Connect the violet/white lead to the lead whose
voltage changes when the shift lever is put in reverse.
Unless connected, the sensor may not detect your
vehicle traveling forward/backward properly, and thus
the position of your vehicle detected by the sensor may
be misaligned from the actual position.
Note
The position of the parking brake
switch varies depending on the
vehicle model. For details, consult
your authorized Pioneer dealer or an
installation professional.
WARNING
LIGHT GREEN LEAD AT POWER CONNECTOR IS
DESIGNED TO DETECT PARKED STATUS AND
MUST BE CONNECTED TO THE POWER SUPPLY
SIDE OF THE PARKING BRAKE SWITCH.
IMPROPER CONNECTION OR USE OF THIS LEAD
MAY VIOLATE APPLICABLE LAW AND MAY RESULT
IN SERIOUS INJURY OR DAMAGE.
Connection method
Clamp the lead of the power supply
side of the parking brake switch.
Clamp firmly with needle-nosed
pliers.
Note
When you use a rear view camera, please
make sure to connect this lead. Otherwise
you cannot switch to the rear view camera
picture.
Power supply side
Ground side
Parking brake switch
10
En
Connecting the system
Section
02
When connecting to separately sold power amp/subwoofer
Front outputs
(FL, FR)
This product
Power amp
(sold separately)
RCA cables
(sold separately)
Power amp
(sold separately)
Subwoofer/rear outputs
(SW/RL, SW/RR)
Power cord
System remote control
Blue/white
To system control terminal
of the power amp
(max. 300 mA 12 V DC).
English
Left Right
Subwoofer or
Rear speaker
Front speaker Front speaker
Subwoofer or
Rear speaker
Note
You can change the RCA output of the subwoofer depending on
your subwoofer system. (Refer to the Operation Manual.)
11
En
Section
02
Connecting the system
When connecting a rear
view camera
When this product is used with a rear view
camera, it is possible to automatically
switch from the video to rear view image
when the shift lever is moved to REVERSE
(R). Rear Camera mode also allows you to
check what is behind you while driving.
WARNING
USE INPUT ONLY FOR REVERSE OR MIRROR
IMAGE REAR VIEW CAMERA. OTHER USE
MAY RESULT IN INJURY OR DAMAGE.
CAUTION
The screen image may appear reversed.
•
•
The rear view camera is used as an aid to
keep an eye on trailers, or backing into a
tight parking spot. Do not use this function
for entertainment purposes.
Objects in rear view may appear closer or
•
more distant than in reality.
Please note that the image area shown by
•
the rear view camera may differ slightly
when full-screen images are displayed when
backing and when checking the rear of the
vehicle while moving forward.
This product
Power cord
Violet/white
(REVERSE GEAR
SIGNAL INPUT)
Rear view camera
(e.g. ND-BC5)
(sold separately)
For more details about the wiring, refer to
Connecting the power cord (2) on page 10.
Notes
To display the rear view camera image, set
•
the rear view camera to on.
Connect this product to the rear view cam-
•
era only. Do not connect to any other equipment.
12
En
Loading...