light
PIKOSmartControl
–
light
the digital future of
model railway control!
INSTRUCTION MANUAL
System
light
2
PIKOSmartControl
Instruction manual
System
light
3
System
light
Index
1. PIKO SmartControl
1.1 Features .................................................................................................................................... 6
1.2 Ports .......................................................................................................................................... 7
2 First steps with the PIKO SmartControl
3 The control elements of the PIKO SmartController
4 Operating the PIKO SmartController
4.1 Loco mode ............................................................................................................................. 10
4.2. DC driving mode .................................................................................................................... 10
4.3. AC driving mode ................................................................................................................... 11
4.4. Turnouts mode ....................................................................................................................... 11
4.5. Turnout lists ............................................................................................................................ 11
4.6. Routes mode .......................................................................................................................... 11
4.7. Change loco data mode ........................................................................................................ 11
4.8. PIKO SmartController
4.9. Help function .......................................................................................................................... 14
®
4.10. LocoNet
................................................................................................................................. 14
4.11. Permanent memory ............................................................................................................... 14
5. Menu operation ..................................................................................................................... 14
5.1. Input of numbers ................................................................................................................... 14
5.2. Conguration......................................................................................................................... 14
5.2.1 Menu point “language“ ......................................................................................................... 15
5.2.2 Menu point „brightness“ ...................................................................................................... 15
5.2.3 Menu point “help“ ................................................................................................................. 15
5.2.4 Menu point “throttle“ ............................................................................................................. 15
5.2.5 Menu point „switch-off time“ ................................................................................................ 16
5.3 Menu point “loco-warnings“ ................................................................................................. 16
5.4 Menu point „routes“ ............................................................................................................. 17
5.5 Menupoint“turnoutconguration“ .................................................................................... 17
5.6 The loco mode ....................................................................................................................... 17
5.7 Light- and special functions ................................................................................................. 18
5.8 Double traction ....................................................................................................................... 18
5.9 Select last loco ....................................................................................................................... 18
6. Turnout mode ......................................................................................................................... 19
basics .................................................................................................. 6
light
........................................................................... 7
light
......................................................... 8
light
.............................................................................. 10
light
„Lock“ (button lock) ................................................................... 13
light
4
6.1 Select turnout mode .............................................................................................................. 19
6.2 Control magnetic accessories .............................................................................................. 19
7. Routes mode .......................................................................................................................... 19
7.1 Select routes mode ................................................................................................................ 19
7.2 Activate routes ....................................................................................................................... 20
8. The programming mode (PIKO SmartController
) .......................................................... 20
light
8.1 Select programming process ............................................................................................... 20
8.2 Read/program loco (decoder) address ................................................................................ 20
8.3 CV programming on the programming track ...................................................................... 21
8.4 CV programming on the main track (POM).......................................................................... 21
9. „Change loco data“ mode ..................................................................................................... 21
9.1 Change loco data ................................................................................................................... 21
10 Special function symbols ...................................................................................................... 23
I. Further features ..................................................................................................................... 24
a. Connection of a turning loop ............................................................................................ 24
®
b. V.2 LocoNet
....................................................................................................................... 24
II. Display operating status ....................................................................................................... 25
III. Technical data ........................................................................................................................25
a. Digital central station ........................................................................................................ 25
b. PIKO SmartController
................................................................................................... 25
light
IV. Safety warnings ..................................................................................................................... 26
V. FAQs ........................................................................................................................................ 26
VI. Technical service hotline .......................................................................................................26
You can nd all the information you need on our PIKO SmartControl
Products, specications and availability subject to change.
Duplications and reproductions of this documentation are strictly forbidden and need to be allowed by PIKO in writing.
LocoNet® is a registered trademark of Digitrax Inc., Panama City FL, USA
5
info page www.piko-shop.de/?a=scl
light
System
light
PIKO SmartControl
consists of the hand controller PIKO SmartController
PIKO SmartBox
With PIKO SmartControl
popular data format for the digital control of DC model railways, signals and turnouts), switch magnetic
is a digital control system for aspiring model railway beginners and experts. It
light
which are connected via the enclosed spiral cable.
light
you can control DCC locomotives (Digital Command Control is the most
light
and the digital central station
light
accessories (e.g. turnouts) and activate routes. It masters everything the model railway enthusiast
needs for a comfortable operation of digital model railways.
The PIKO SmartController
By using a PIKO Lok-Net converter it can also be used as an additional corded hand controller for the
is the intelligent hand controller for the PIKO SmartControl
light
system.
light
PIKO SmartControl system or other digital central stations with LocoNet®.
1. PIKO SmartControl
The digital central station PIKO SmartBox
coordinates and processes all commandos according to their relative importance. It generates the DCC
track signal and establishes the connection to the hand controller. With the PIKO SmartController
you can control the PIKO digital central station. You can control locomotives, switch magnetic
basics
light
is the heart of the PIKO SmartControl
light
system. It
light
light
accessories and activate routes of the digital central station. It is connected to the LocoNet®-T port of
the digital central station via the enclosed spiral cable.
1.1.Features
• With the PIKO digital central station you can individually and simultaneously control up to
20 locomotives.
• The digital central station supports the DCC data format with 14, 28, und 128 speed steps.
• You can individually set the data format for 9.999 locomotive addresses.
• You can control up to 24 special functions for each locomotive address.
• With the digital central station from PIKO you can control up to 2.048 magnetic ac-cessories
with DCC data format, for example turnouts and signals.
• The states of the magnetic accessory addresses 1-1.024 are permanently saved, so that
they are displayed correctly after a reboot of the system.
• The PIKO SmartController
include numerous switching sequences)
• Every route can switch between the magnetic accessory no. 1 to 2.048 in up to 10 steps.
• The output of the main track of the digital station supplies a current of 2 A and is protected
against short circuits and overheating. This allows the simultaneous oper-ation of up to 4
trains (depending on the used scale) without having to use any additional boosters.
• The digital central station is equipped with an extra output for a programming track with a
maximum current of 250 mA. During programming the output of the main track is
switched off
• With the PIKO digital central station you can program DCC decoder as well as pro-
grammable LocoNet® devices.
• The station also has a special output for a turning loop relay.
• The PIKO digital central station is equipped with two LocoNet® ports at the back.
can memorize up to 16 different routes (each route can
light
6
1.2. Ports
The PIKO digital central station is equipped with ports for a main track, a programming track, a turning
loop relay and further Loco-Net® devices as well as a port for the power supply.
mode
lok
1 2 3
4 5 6
7 8
9
0
.
_
+
.
15V-
power
supply
programming track main track
The programming track serves only for the programming of DCC decoders. During operation it is
currentless and a connection to the main track is not allowed.
2. First steps with the PIKO SmartControl
light
At rst, please connect all components according to the following graphic.
mode
lok
1 2 3
4 5 6
7 8
9
0
_
+
.
15V-
power
supply
Now, please turn on the operating voltage by plugging the power supply into the power outlet. A
switchable multisocket outlet can be benecial.
The green control LED should now be turned on and the PIKO SmartController
locomotive mode.
should display the
light
7
System
light
If you purchased the PIKO SmartControl
directly start playing due to the plug and play character of the sets. All traction units of the starter sets
are already incorporated into the PIKO SmartController
3. The control elements of the PIKO SmartController
as part of a PIKO SmartControl
light
.
light
starter sets, you can
light
light
Overview
Display
Fahrregler
mode
up
down
Ziffernblock
lok
stop / löschen
Enter
Display
Clearly structured high denition display that shows the symbol of the current operating mode and the
locomotive or base address at the top of the display. In the middle it shows basic information about
the currently controlled locomotive and at the bottom you can nd information about the switching
functions, depending on the chosen mode.
The display clearly shows all the information about the locomotive, the speed, the driving direction and
the state of the locomotive’s special functions or of the currently chosen operating mode (e. g. position
of the switches in the turnout mode).
8
Speed regulator
The hand controller is equipped with a rotary encoder wheel to control the speed, the driving direction,
the emergency stop of the locomotive and to choose the locomotive’s data set as well as the symbols
and their position in the name of the locomotive.
The following part describes the different keys of the controller:
up/down([▲]/[▼])
• In loco mode, changing of the special function blocks
light, F1 - F8; light, F9 - F16; light, F17 - F24; light - F32.767 (activate in con-guration
mode)
• In turnouts mode, changing of the base address +8 or -8
• In routes mode, changing of the base address +8 or -8
• In congurationmode, changing of parameters
mode
• Selection of the operating mode: [1] = loco mode, [2] = turnouts mode,
[3] = routes mode, [4] = programming mode, [5] = change loco data,
[6] = conguration mode
lok
• Initiate loco selection or switch back to loco mode from every other mode
keypad
• Number keys [0] - [9], enter loco address, switch into different modes, selection of the
operating mode and sub-menus
stop / delete
•Turn DC voltage on and off, delete last entered number or loco data set
Enter [↩]
• Conrm an input
• Conrm a loco data set in mode “change loco data”
• Initiate input of an address and conrm in loco mode, turnouts mode and routes mode
• Start a reading or programming process in programming mode
9
System
light
4. Operating the PIKO SmartController
light
4.1. Loco mode
The display shows the symbol, the name, the address, the speed and the driving direction of the
currently controlled locomotive.
The lighting and up to 8 special functions can directly be controlled via the numeric keypad. While
operating in DCC mode, 32.768 special functions can be activated for each loco address.
All locomotives can be controlled with the large rotary encoder wheel. When switching to another
locomotive, the intelligent controller without an end stop automatically takes over the speed of the new
locomotive. You can switch between DC and AC driving mode.
4.2. DC driving mode
The DC mode recreates the control of a locomotive on an analog two-wired DC system.
Operating principle of the DC driving mode
While operating in the DC driving mode, you can increase the speed in one direction, by turning
the encoder wheel to the right, starting at a speed of zero. If you turn the wheel to the left the
speed decreases until your train comes to a halt. If you keep turning the wheel of the PIKO
SmartController
If the top speed is reached, further turning of the wheel has no effect. While in this operating mode, a
to the left, the loco will start to accelerate into the other opposite direction.
light
gentle press on the wheel will stop the vehicle immediately.
10
4.3. AC driving mode
The AC driving mode recreates the control of a locomotive on an analog three-wired AC system.
While operating in the AC mode, you can increase the speed by turning the encoder wheel to the right
and decrease it by turning it to the left. If the top speed or a speed of zero is reached, further turning of
the wheel has no effect. To switch the driving
direction, you have to gently press down on the encoder wheel of the
PIKO SmartController
immediately. After the emergency stop you can then change the driv-ing direction.
. If you press on the wheel while the train is moving, the locomotive stops
light
Operating principle of the AC driving mode
4.4. Turnouts mode
With the PIKO SmartControl
the numeric key pad of the PIKO SmartControllerl
accessories. The display shows you the current turnout position with the symbol of a switch (factory
setting) or with one of 27 symbols of your choice.
system you can control up to 2.048 DCC magnetic accessories. With
light
, you can directly control groups of 8 magnetic
light
4.5. Turnout lists
With the PIKO SmartController
addresses. Within these lists, the order of addresses is variable. You can also assign symbols and
names with two characters for every magnetic accessory.
you can create up to 4 turnout lists, each with up to 8 turnout
light
4.6. Routes mode
If there are routes saved on the PIKO SmartController
of your controller.
You nd further information about this topic in chapter 7.
, you can activate them with the routes mode
light
4.7. Change loco data mode
You can create your own loco datasets in the loco database of the PIKO SmartController
you can assign loco symbols, addresses, names and symbols for special functions. You can choose
between over 60 loco symbols and over 160 symbols for special functions.
You can choose a specic locomotive of a digital system with its respective loco address. The address
is a sequence of numbers, that marks the decoder of a locomotive. To illustrate the operating principle
of the loco database, we give you an example of a locomotive with the address “1234” on the following
pictures.
light
. Here
11
System
light
To simplify the selection of a locomotive, you can assign a symbol (in our example the symbol of an
ICE railcar) and a name (in our example “PIKO ICE Test”) to each loco address. Once assigned, this
data set is saved on the PIKO SmartController
choose the loco by its name on the list.
. For every new selection of a locomotive, you can
light
We show you how to create loco datasets in chapter 9.1 “change loco data”.
If you want to control a vehicle with the PIKO SmartController
address or the assigned name.
, you have to select it by its decoder
light
While in loco mode, you can start the selection of a locomotive by pressing on [lok] or [↩]. By turning
the encoder wheel, you can select a locomotive out of the loco database (if there are any available
datasets). When you found the desired locomotive, you can select it by again pressing [lok] or [↩].
12
If the desired loco cannot be found on the list, you can enter a loco address with the keypad. The
[stop/delete] key deletes the lastly entered number and the [lok] and [↩] key conrms the input.
Addresses of the vehicles included in the PIKO SmartControl
traction ve-
adress symbol function F0 function F6
starter sets
light
hicle
electric loco 4
diesel loco 5
multiple units 6
4.8. PIKO SmartController
„Lock“ (button lock)
light
The functions of the PIKO SmartController
on and off-turning of the track current. All other functions as well as the [lok] key are deactivated in this
light on/off shunting mode
light on/off shunting mode
light on/off shunting mode
can be limited to the operation of a locomotive and the
light
state.
Controller lock (key lock): [mode] key and [0] key, keypad locked; [mode] key and [0] key, keypad
unlocked.
13
System
light
4.9. Help function
The situational help function offers you automatic help in the current operational situation. If you do not
need that help anymore, you can simply turn the help function off.
4.10. LocoNet®
The LocoNet® port turns the PIKO SmartController
railway system. You can separate it from the LocoNet® at any time and plug it back it at another place.
The displayed information will be updated automatically.
into a permanent companion around your model
light
4.11. Permanent memory
Once entered, all congurations of the PIKO SmartController
even when the device is no longer activated.
are permanently saved on the device,
light
5. Menu operation
Every mode of the PIKO SmartController
the control of your model railway.
These menus of the PIKO SmartController
The [mode] key switches between operating modes. By pressing it, the main menu will show all
operating modes. They are numbered 1 to 6 and can be activated by pressing the respective number
key on the keypad.
has sub-menus for the basic settings of the devices and
light
can be reached by pressing the [mode] key.
light
5.1. Input of numbers
The input of numbers, for example to enter a loco or base address, is done via the keypad. As soon as
you press a number key, you can complete the input and conrm it by pressing the [↩] key. With the
[stop/delete] key you can delete the last entered number.
5.2.Conguration
The congurations of the PIKO SmartController
permanently saved on the device.
The menu for the congurations can be reached by pressing the [mode] key and then selecting the
menu point “conguration” by pressing [6].
Here you can use the keys [▲] or [▼] to scroll between two pages of possible congurations.
Page 1 of the conguration menu includes the following points:
1 = language
2 = brightness
3 = help
4 = throttle
5 = switch-off time
can be changed in a simple menu and are
light
14
Page 2 of the conguration menu includes the following points:
1 = loco-warnings
2 = 32.000 functions
3 = routes
4 = turnout conguration
5.2.1. Menu point “language“
By pressing [1] on page 1 of the conguration menu you can retrieve the language settings. The
desired language can be selected with the [▲] and [▼] keys and has to be conrmed by pressing on
[↩].
You can choose between the following languages:
• German (default setting)
• Danish
• English
• French
• Italian
• Dutch
• Polish
• Swedish
• Spanish
5.2.2. Menu point „brightness“
By pressing [2] on page 1 of the conguration menu you can set the brightness of the display. You can
choose between 15 brightness levels. The brightness can be selected with the [▲] and [▼] keys. The
brightness of the value number on the display shows the actual brightness level that will be set. The
level has to be conrmed by pressing on the [↩] key.
5.2.3. Menu point “help“
By pressing on [3] on page 1 of the conguration menu you can reach the help function. When
switched on, small helping windows will appear for every step in the “congurations” and “change
loco data” modes. You can turn the help function on and off with the [▲] and [▼] key. To conrm your
selection press [↩].
5.2.4. Menu point “throttle“
With the PIKO SmartController
and 4.3). The device is factory-set in DC driving mode.
By pressing [4] on page 1 of the conguration menu you get to the menu point “throttle”. With the
[▲] - and [▼] -keys you can switch between the two modes. To conrm your selection press [↩]. For
more information, please see chapter 5.6 “loco mode”.
you can switch between a DC and an AC driving mode (s. point 4.2
light
15
System
light
5.2.5. Menu point „switch-off time“
To preserve the display of the PIKO SmartController
amount of time.
To reactivate the display, press the [lok] -key.
By pressing [5] on page 1 of the conguration menu, you can set the switch-off time of the PIKO
SmartController
The maximum switch-off time is 248 seconds. If the switch-off time is set to 0, the display will not turn
. The switch-off time can be set with the [▲] - and [▼] keys in steps of 8 seconds.
light
off during operation To conrm your selection press [↩].
it automatically turns dark after a preset
light
5.3. Menu point “loco-warnings“
If more than one PIKO SmartController
a locomotive is already controlled by a different PIKO SmartController
by selecting the locos address. For this process every PIKO SmartController
number, which is not visible in the system.
There are four settings for this operational situation:
• 0 = No loco-warning
• 1 = loco-warning ”LOCOMOTIVE ALREADY UNDER CONTROL“. The PIKO
SmartController
• 2 = loco-warning ”LOCOMOTIVE ALREADY UNDER CONTROL“. The PIKO
SmartController
• 3 = loco-warning “LOCOMOTIVE NOT CONTROLLABLE”. The loco address cannot be
connects its ID with the loco address and is able to control it.
light
does not connect its ID with the loco address and is able to control it.
light
accepted and controlled. The display shows “LOCO?“. Another loco address can now be
selected.
is used and loco-warning is turned on, you can see whether
light
with activated loco-warning
light
has its own ID
light
By pressing [1] on page 2 of the conguration menu, you can set the loco -warning of the PIKO
SmartController
it by pressing [↩].
. By pressing [▲] or [▼] you can switch between the different settings and conrm
light
ATTENTION: If loco-warning 1 is switched on and a loco address is quitted, the connection to this loco
address will be deleted.
ATTENTION: If loco warning 1 is switched on and the PIKO SmartController
the last activated loco address has to be reactivated by another PIKO SmartController
warning 1 or at the digital central so that the connection is deleted.
ATTENTION: Please note that only the PIKO SmartController
warning is only available for PIKO SmartController
. Other controllers do not support loco warning.
light
16
can transfer this ID. That’s why loco
light
quits the system,
light
with loco
light
5.4. Menu point „routes“
The PIKO SmartController
By pressing [3] on page 2 of the conguration menu, you reach the routes menu.
Here you can enter switching sequences for the routes. They will be automatically saved on the PIKO
SmartController
By pressing [1] you can enter the number of the route (1 - 16) you want to change. The number has to
light
.
be entered with the number keys and conrmed with the [↩] -key.
By pressing [2] you can enter the individual steps (1 - 10) of the route. The steps have to be entered
with the number keys and conrmed with the [↩] -key.
By pressing [3] you can enter the addresses for the magnetic accessories assigned to the steps 1-10.
The addresses have to be entered with the number keys and con-rmed with the [↩] -key.
After pressing [4] you can use the [▲] - and [▼] – keys to choose the switch direction “red” or “green”
for the respective address of the magnetic accessory. Afterwards you have to conrm your choice with
the [↩] -key.
By pressing [0] you can leave the routes menu. All entered routes are automatically memorized.
can memorize up to 16 routes.
light
5.5.Menupoint“turnoutconguration“
By pressing [4] on page 2 of the conguration menu, you reach the “turnout conguration” menu.
Here you can assign symbols to your turnout addresses.
You can create up to four turnout lists, in which you can save up to eight turnout addresses in random
order. Besides the symbols you can also assign two-digit descriptions to these addresses.
After pressing [1] in the turnout conguration menu you can use the [▲] and [▼] keys to switch
between “ALL” (the PIKO SmartController
order) or “LIST” (the PIKO SmartController
addresses).
Conrm your selection with the [↩] key.
By pressing [2] (only when “LIST” is activated) you can dene the position (1 - 32) of the turnout
addresses within the four turnout lists using the number keys. Conrm your selection with the [↩] key.
By pressing [3] you can choose the turnout address you want to congurate. You enter the address by
using the number keys and conrming it with the [↩] key.
By pressing [4] (only when “LIST” is activated) you can assign a two-digit description to the address.
You can change the position of the cursor by turning the encoder wheel.
Afterwards press the encoder wheel down for conrmation.
Now you can choose the rst digit by again turning the encoder wheel.
Press the encoder wheel again to conrm your choice. Repeat the steps for the sec-ond digit.
When both digits are selected, conrm your choice by pressing [↩].
By pressing [5] you can assign a symbol to the turnout address. Use the [▲] and [▼] keys to choose a
symbol from the list and conrm your choice with the [↩] key.
By pressing [0] you can leave the turnout conguration menu.
now uses all turnout ad-dresses (1 – 2.000) in ascending
light
now uses the four turnout lists with up to eight turnout
light
ATTENTION: You can assign different symbols to the addresses in the “ALL” and “LIST” mode.
5.6. The loco mode
In loco mode you can activate and control locomotives. You can activate loco mode from every menu
by pressing the [lok] key.
The control of the speed and driving direction of every loco also works while being in the turnout or
routes mode.
17
System
light
5.7. Light- and special functions
You can activate light and special functions F0 to F24 of loco and function decoders by using the
number keys of the PIKO SmartController
The [0] key always controls light functions (F0).
In the basic position, the keys [1] to [8] control special functions F1 to F8.
By pressing [▲] once, the number keys [1] to [8] will control the functions F9 to F16.
By pressing [▲] again, you can control the functions F17 to F24.
By pressing [▲] a third time, the number keys will control functions F1 - F8 again.
The [▼] key will set back the selection of the special functions one step.
The displayed symbols show the respective function numbers and the current state of the special
functions so you can see which functions are turned on or off. You can assign the symbols in the
respective loco data set. If you choose a locomotive by its loco address that is not yet saved as a loco
data set, the special functions will be displayed with standardized symbols.
Control of special functions higher than F24
light
.
If your digital central station (PIKO SmartBox and PIKO SmartBox
special functions in DCC format and you activated this function in the conguration menu of your PIKO
SmartController
you can enter the number of the special function (0 – 32.767) with the number keys and conrm it by
, you can reach a fourth level of special functions with the [▲] and [▼] keys. There
light
) can control more than 24
light
pressing [↩]. You can delete the last entered digit by pressing the [stop/delete] key. You activate this
function by pressing [1] and deactivate it by pressing [0]. The current state of the function cannot be
displayed.
5.8. Double traction
If you want to couple two locomotives, for example to pull a heavy train, they have to synchronously
receive the same operating commands. The PIKO SmartController
into one double traction, so that both can be con-trolled by one controller.
If you successively press [lok] and [▲] while in loco mode, you can couple a traction locomotive to the
currently controlled locomotive (basic locomotive). This traction
locomotive can then be retrieved by its loco address or via the encoder wheel in the loco data base.
After conrming the selection with the [↩] key, a “D” (for double traction) will be displayed in front of
the address of the basic locomotive. When the traction locomotive is selected, a “S” (slave) will be
displayed in front of its address. The special functions of the traction locomotive can be controlled
independent of the basic locomotive. The speed and the driving direction of the traction locomotive can
not be changed.
When controlling the basic locomotive, the traction can be deactivated by pressing [lok] and [▼].
merges the two loco addresses
light
5.9. Select last loco
The PIKO SmartControl
to switch between the currently and the last used locomotive, for example for comfortable shunting,
you do not have to insert the address again or select the locomotive out of the loco database. Just
consecutively press [lok] and [mode] to switch back to the last controlled locomotive.
system memorizes the last selected locomotive address. If you want
light
18
6. Turnout mode
With the PIKO SmartController
8 turnout addresses can be directly reached with the numeric keypad. The current switching position is
indicated on the display by the respective symbol.
While in turnout mode the name of the locomotive is visible and you can still control the speed and
direction with the encoder wheel. This makes for a lot of fun during shunting manoeuvres on turnout
streets.
6.1. Select turnout mode
To select the turnout mode, press [mode] and then [2].
Now you can control up to eight turnout addresses with the keys [1] to [8].
6.2. Control magnetic accessories
The number keys [1] to [8] control turnout addresses. Every operation of the keys switches the function
of the turnout e.g. the position of the switch from straight to turning.
If “ALL” is activated in the turnout conguration, [1] switches the turnout of which the address is
currently displayed on the PIKO SmartController
with the subsequent addresses. If the basis address is 1, the eight number keys switch the turnout
addresses 1 to 8. If the basis address is for example 47, the eight number keys switch the turnout
addresses 47 to 54.
By pressing the [↩] key, a new basis address can be entered via the number keypad. The [stop/delete]
key deletes the last entered digit. By pressing [↩] the entered basis address can be conrmed.
The [▲] and [▼] keys change the current basis address by +8 or -8.
In the factory settings every turnout is displayed by a turnout symbol at the bottom of the screen. The
turnout position on the screen shows the current direction of the turnouts (turning=red; straight=green).
If there are symbols assigned to the turnout addresses in the turnout conguration, they accordingly
display the turnout position.
If “LIST” is activated in the turnout conguration, the keys [1] to [8] switch the turnout addresses, which
are listed on the four turnout lists. With the [▲] and [▼] keys you can scroll between the four turnout
lists. The address eld displays the currently used turnout list (1-4).
you can control up to 2.048 DCC magnetic accessories. Groups of
light
screen. The keys [2] to [8] switch the turnouts
light
7. Routes mode
The PIKO SmartController
Groups of up to 8 routes can directly be reached via the number keys. An active route is displayed by
the turnout symbol with switching turnout position on the screen.
While in routes mode, the name of the locomotive is visible and you can still control the speed and
direction of the locomotive with the encoder wheel.
7.1. Select routes mode
To select the routes mode, press [mode] and then [3].
Now you can activate routes by using the number keys [1] to [8].
can control up to 16 routes.
light
19
System
light
7.2. Activate routes
The keys [1] to [8] of the number key pad activate the routes. The key [1] activates the route of which
the basis address is displayed in the address eld on the screen. The keys [2] to [8] activate the routes
with the subsequent addresses. If the basis address is 1, the eight number keys activate the routes 1 to
8. If the basis address is 9, the eight number keys activate the routes 9 to 16.
With the PIKO SmartController
of eight addresses or random addresses between 1 and 73. To do that, press [↩] so you can enter a
new basis address with the number keys. The [stop/delete] key deletes the last entered digit. The
[↩] key conrms the entered basis address.
With the [▲] and [▼] keys you can change the current basis address by +8 or -8.
To learn more about how to create routes or commands please read chapter 5.4. about the menu point
“routes mode”.
you can use the [▲] and [▼] keys to switch between the two blocks
light
8. The programming mode (PIKO SmartController
In programming mode, you can congurate DCC locomotives, function decoders or LocoNet®
components.
light
)
8.1. Select programming process
By pressing [mode] and then [4] you can select the programming mode.
Now you can use the keys [1] to [4] to select the desired programming process.
1 = LOCOADDRESS - PG. (Read and program loco address)
2 = CV - PROG. TRACK (CV programming on the programming track)
3 = CV – MAIN TRACK (CV programming on the main track)
A CV (Conguration Variable) is there to change the conguration of a decoder, for example, you can
change the loco address with CV1. If you assign the value 5 to this CV, the loco can be controlled
under the loco address 5.
8.2. Read/program loco (decoder) address
If a locomotive with a DCC decoder is on the programming track and the menu point
„LOCOADRESS - PG.“ is selected, you can select and program the loco address.
By pressing [1], the current loco address can be selected.
After a few seconds the selected loco address will be displayed behind “LOCOADDR.:”
To leave the programming menu, press [lok]. The loco address can now be controlled with the encoder
wheel.
At rst, press [3] to program a new loco address. Now you can enter a desired ad-dress between 1 and
9.999 and conrm it by pressing [↩]. To continue with the programming process, press [2].
After a few seconds, the result of the programming process will be displayed at the bottom of the
screen.
„PROG: OK “ – programming successful
„PROG: ERROR “ – programming failed
„PROG: NO LOCO“ – no loco on the programming track
„PROG: SHORT “ – short circuit of the loco or on the programming track
By pressing the [lok] or [mode] key you can leave the programming menu.
20
8.3. CV programming on the programming track
If there is a programable DCC loco on the programming track and the menu point „CV - PROG.
TRACK“ is selected, you can select and program all CVs between 1 and 1.024. Please refer to your
decoder instruction for more information about the respective CVs and their range of values.
After pressing [1], the number of the desired CV can be entered and conrmed with the [↩] key.
The current value of the CV will now be read and displayed after “2= VAL.:”.
Now press [2] and enter the desired value for this CV. Conrm your input with the [↩] key. The
programming will be executed automatically.
The result of the programming process will be displayed in the bottom line after a few seconds.
„ PROG: OK “ - programming successful
„ PROG: ERROR “ - programming failed
„ PROG: NO LOCO “ - no loco on the programming track
„ PROG: SHORT “ - short circuit of the loco or on the programming track
By pressing the [lok] or [mode] key you can leave the programming menu.
PLEASE NOTE: To test whether or not your programming was successful, you should put your loco on
the main track. The port of the programming track is currentless during normal digital operation.
8.4. CV programming on the main track (POM)
If you want to program a loco’s CV, the loco has to be placed on the main track. All other vehicles can
remain on the main track. This way you can make necessary modications to the start-up and braking
behaviours of your vehicles during normal operation of your railway system.
While being in the menu „CV – MAIN TRACK“, you can program all CVs between 1 and 1.024.
The loco address cannot be programmed on the main track. For more information, please read the
instruction manual of your loco decoder.
After pressing [1] you can enter the address of the loco you want to program. Conrm your input by
pressing [↩].
Now press [2] and enter your CV number. Again, conrm by pressing [↩].
Now press [3] and enter the desired value for your CV. Again, conrm by pressing [↩].
The bottom line on the display will show „POM SENT“. That means your programming was successful.
CVs cannot be read out on the main track. If you want to check, whether a programming process on
the main track was successful, you have to try out the programmed CV.
By pressing the [lok] or [mode] key you can leave the programming menu.
9. „Change loco data“ mode
When the “change loco data” mode is selected, the PIKO SmartController
help window, which explains the most important keys for this menu.
With the next selection of a key, the help window will disappear again.
If no help is needed, you can deactivate this function in the conguration menu (see chapter 5.2.3).
9.1. Change loco data
By pressing [mode] and then [5] the mode “change loco data” is selected.
With the keys [1] to [5] you can select what you want to change.
First, you have to enter the loco address which you want to change by pressing [1] and then use the
number keys to enter the address. Conrm the address with the [↩] key.
21
will at rst show a small
light
System
light
By pressing [2] you can change the loco symbol. The symbol can be selected out of a list by using the
[▲] and [▼] keys and has to be conrmed with the [↩].
By pressing [3] you can change the loco name.
• The position of the cursor can be changed by turning the encoder wheel.
• Then, please press sown the encoder wheel.
• Now you can select the rst digit by turning the encoder wheel. To enter a number, you can
use the respective number keys. The [stop/delete] key generates blank space.
• If you press the encoder wheel again, the selected number or letter is accepted and you can
turn to the next digit.
• When all digits of the loco name are entered, the name can be conrmed and saved by
pressing [↩].
By pressing [4] you can switch to the “change func. icon” menu.
Here you can assign symbols to every loco function from 0 to 24. Additionally, you can decide whether
to use the respective functions as a switch or pusher function. (switching characteristic).
Switch function: With every keystroke the function switches between “on” and “off”.
Pusher function: If you press the key and hold it, the function is turned on. By letting go of the key, the
function turns off.
• At rst press [1] to decide whether
o you want to set the conguration of the symbols to “UNI”. Here, all spe-cial functions are
displayed by standard symbols (a circle) and the “switch function” is activated (function
stays “on” until the key is pressed again)
o you want to set the conguration of the symbols to “MULTI”. Here, you can assign an
individual symbol to each function and you can decide whether to use the “switch function”
or the “pusher function”.
On the following picture you can see an example where an individual symbol and the “switch function”
is assigned to F1.
• With the [▲] and [▼] keys you can choose between one of the two possibili-ties and conrm it
with the [↩] key.
• If “MULTI“ is activated you can press [2] and enter the function number (0 - 24) you want to
change. The number can be entered with the number keys and conrmed by pressing [↩].
• By pressing [3] the function symbol can be changed. You can select the sym-bol with the [▲]
and [▼] keys out of the symbol list and conrm it by pressing [↩].
22
• By pressing [4] and using the [▲] or [▼] key, you can select between the “switch function”
and the “pusher function”. Conrm your choice with [↩].
• Leave the sub-menu by pressing [0].
You can change the data format by pressing [5] and then use the [▲] and [▼] key to select. Conrm
your selection by pressing [↩]. You can select between 14, 28 and 128 DCC speed levels.
Speed levels: The speed of every locomotive is not controlled linearly but through speed levels. The
higher the number of speed levels the more sensitive you can control the vehicle between a halt and its
top speed.
If you want to save the data set, press the [↩] key to leave the menu.
If you want to delete a selected loco data set, press the [stop/delete] key.
By pressing [lok] or [mode] you can leave the menu without saving the changes to the loco data.
10. Special function symbols
Hereafter you nd a short overview of the before mentioned special function symbols and their
meanings (non-binding). Overall, there are more than 160 special function symbols available.
Preset: no Symbol
Sound
Mute Sound
Horn
Bell
Whistle
Conductor Whistle
Brake Squeal
Diesel motor
Smoke generator
Magnet
I. Further features
Light
Interior Light
High beam
Tail Light
Tail Light
Light front and back
Interior Light
Driver cabin lighting
Start/Brake Inertia
Doors Opening
Power Pickup
Driver cabin - Front
Driver cabin - Rear
Move up/down
Move right/left
Hook Up
Hook Down
Turn right
Turn left
Telex coupling
Uncoupler
Shunting gear
23
System
light
a. Connection of a turning loop
Because of the polarity of the 2-wire track, driving through a turning loop automatically leads to a short
circuit. The most comfortable way to avoid the polarity problem is to install a reverser (turning loop
switch). The PIKO SmartBox
only have to install a turning loop relay according to the following outline. When connecting the relay to
the track please try to keep the connection points as close to the joint as possible.
Smartbox
light
Haupt
KS-
Gleis
Relais
rot
schw.
turning loop relay
Prog.
Gleis
rot
schw.
rot grün
already comes with a pre-installed reverser. To switch the polarity, you
light
turning loop joint
The turning loop hast
o be at least as long
as the longeest train
turning loop joint
If a short circuit is occurring, the turning loop relay will be switched before the system shuts down. If the
short circuit is caused by a train driving over a turning loop joint, the polarity of the turning loop relay
will be switched so quickly, that the driving performance of the train is not affected.
b. V.2 LocoNet®
The digital central is equipped with two LocoNet® ports at the back. The LocoNet® T-port of the digital
station serves for the connection of the PIKO SmartController
using a ve-way LOCONet® distributor you can connect further LocoNet® devices to the central, for
example like further PIKO SmartController
LocoNet®
, response modules, LocoNet® switches and other
light
devices. The LocoNet® T-port provides a supply current of 500 mA for the connected devices. If this
current is not sufcient, you can provide another 500 mA by adding an extra LocoNet® power input.
via the enclosed spiral cord. By
light
II. Display operating status
24
Red LED off - Green LED on Track current switched on
(normal operating status)
Red LED on - Green LED off Track current switched off
(stop key pressed, short circuit or during active
decoder programming)
RedLEDon-GreenLEDashing Overtemperature
®
RedLEDashing-GreenLEDoff Undervoltage at the LocoNet
(Overload on the LocoNet
T power supply
®
T port)
RedLEDoff-GreenLEDashing Digital central currently in LocoNet
programming mode
III. Technical data
a. Digital central station
• Power supply: Input: 240 V 50 Hz, Output: 15 V= / 2 A
• max. load main track output: 2 A
• max. load programming track output: 250 mA
• max. load LocoNet®-T: 500 mA
• Dimensions: 104 x 58 x 33 mm
®
b. PIKO SmartController
light
• 38 x 20 mm high denition display for a detailed representation of text and symbols
• LocoNet® port
• Power consumption during normal LocoNet® operation: 25 mA
• Dimensions: 180 x 80 x 35 mm
IV. Safety warnings
25
System
light
• Please read the safety warnings and this instruction manual before using the devices.
• Always treat your PIKO SmartControl
electronics; therefore, you should avoid exposing them to strong vibrations.
devices with care! The devices contain sensible
light
• The devices are no toys and should not be handled by children under the age of 14. However,
children can be operated the devices under the supervision of adults.
• Never insert the connection cables into a power socket!
• Always check the power supply for damages to the cables, the plugs, the case or to other
parts. In case of any damages, do not continue to use the device!
• Only use accessories that are intended for the device!
• Only use the PIKO SmartControl
possible short circuits or wiring errors.
system if you are absolutely sure that there are no
light
• Protect the devices from dust or any dirt. Clean the device on a regular basis.
• Protect the devices from wetness and extreme humidity!
• The devices are designed for the operation in closed rooms and not for the opera-tion
outdoors!
• Manipulations of hardware or software lead to loss of warranty rights!
• Keep this instruction manual in a safe place.
V. FAQ
If you have any questions, please visit our FAQ website. You can nd it on the PIKO web shop
under www.piko-shop.de/?a=faq. There, we provide you with the newest information about the PIKO
SmartControl
the page.
system. If you have any further questions you can nd a contact form at the bottom of
light
VI. Technical service hotline
If you have any technical questions about PIKO products you can reach us via our technical hotline
Tuesdays from 4 PM to 6 PM
Thursdays from 4 PM to 6 PM
under +49 03675 / 8972 - 42.
You can also send us a fax to +49 03675 / 8972 – 50 or write an email to
hotline@piko.de!
Or write us a letter and send it to:
PIKO Spielwaren GmbH
Lutherstraße 30
96515 Sonneberg
Germany
LocoNet® is a registered trademark of Digitrax Inc., Norcross, Ga., USA
26
27
PIKO model trains –
for every layout!
PIKO Spielwaren GmbH
Lutherstr. 30
96515 Sonneberg, GERMANY
www.piko.de · hotline@piko.de
55016-90-7101_E © 2019, PIKO Spielwaren GmbH
Loading...