Model 520/521
TC Simulator(s)
Practical Instrument Electronics
Basic Keypad Operations
EZ-Check™ Switch
1
Slide the switch to select from three user stored values
for the desired calibration points. The User can select HI,
DIAL and LO positions. These values can easily be
changed to suit the calibration requirements.
Operating Instructions
ON/OFF Switch
2
Slide the ON/OFF Switch to turn the Model
520/521 on or off.
3 EZ-Dial™ Knob
The EZ-Dial™ Knob has two adjustment
speeds. Simply turning the EZ-Dial™ Knob will
select fine adjustments. While pressing down
and turning the EZ-Dial™ Knob will make
course adjustments.
Note: When the EZ-Check™ Switch is in the
HI or LO position, pressing and holding the EZ-
Dial™ Knob without turning
or LO values.
will store new HI
.
Model 520/521 Configuration
Instructions for Enabling and Disabling the Configuration Options
1. Turn the Model 520/521 on with the ON/OFF Switch
2. Press the EZ-Dial Knob
CONFIGURATION” message is displayed.
3. Select options by turning the EZ-Dial Knob until the arrow points
to the desired option.
4. The option can be enabled or disabled by tapping the EZ-Dial
Knob.
The Model 520/521 configuration menu will exit automatically after 5
seconds of inactivity and go to normal operation with the options selected.
These options are recalled at turn on until they are changed again.
841 Holt Road #1 • Webster, NY 14580 Tel: 585-872-9350 • Fax: 585-872-2638 sales@piecal.com • http://www.piecal.com/
Practical Instrument Electronics, Inc. Copyright 2003. All rights reserved.
while the “PRESS EZ-DIAL KNOB FOR
3
2
.
520/521-9002 2/27/03 1-3
Model 520/521
Operating Instructions
Model 520/521 Configuration
Model 520/521 Configuration Menu
Auto Off ON (default)/OFF
If Auto Off is ON, the unit will turn off after 30 minutes to save battery life, if there is no user activity. If
Auto Off is OFF the unit will stay on until it is turned off from the keypad. This is typically useful for
manual loading or continuous use.
Display Units °C (default)/°F
Pressing the EZ-Dial Knob to toggles between °C or °F
TC {tc type}
Model 520: The T/C type is fixed as
ordered from the factory and cannot be
changed.
Model 521: To change T/C type, press
the EZ-Dial Knob. Turn the EZ-Dial
Knob to scroll through the list of available
types. Press again to save and return to
the configuration menu.
{tc type} is one of:
B, E, J, K, N, R, S, T, or mV
{tc type} is any of:
B, E, J, K, N, R, S, T, or mV
EZ-Dial™ Knob
Turning the EZ-Dial Knob to adjust the output up or down. Fine adjustments can be made by turning the
EZ-Dial Knob. Coarse adjustments can be made by pressing and turning the EZ-Dial™. New values can
be stored into the HI and LO EZ-Check™ positions by pressing down on the EZ-Dial Knob until “STORED”
is indicated on the display.
EZ-Check™ Switch
The EZ-Check™ Switch has three positions: HI, DIAL, and LO. Its position is shown at the left edge of the
display with “HI” and “LO” indicators. The output is adjustable in all three positions. The EZ-Check™
Switch allows user-selected values to be stored in the HI and LO positions when used in combination with
the EZ-Dial Knob.
To store new EZ-Check™ value(s):
1. Dial the display to match the desired stored outputs for the HI or LO positions.
2. Press down on the EZ-Dial Knob until the confirmation message “STORED” appears.
3. Recall the values by moving the switch between HI, DIAL, and LO.
Operational description: When returning to previously set EZ-Check™ positions, the DIAL position always
recalls the last output value it was dialed to. The HI and LO positions will recall the last STORED value,
NOT the last output value it was last dialed to.
Hint: For faster calibrations, the product has been designed so the position of the switch can be felt. This
tactile feature allows continuous monitoring of the device being calibrated without looking back at the
Model 520/521 display. This is also useful in poor lighting or under difficult operating conditions.
841 Holt Road #1 • Webster, NY 14580 Tel: 585-872-9350 • Fax: 585-872-2638 sales@piecal.com • http://www.piecal.com/
Practical Instrument Electronics, Inc. Copyright 2003. All rights reserved.
520/521-9002 2/27/03 2-3
Model 520/521
Operating Instructions
Connection Diagram
Two Wire Connection to Transmitter
WARRANTY
Our equipment comes with a NIST traceable Certificate and is guaranteed against defective material and workmanship (excluding
batteries) for a period of three years from the date of shipment. Claims under guarantee can be made by returning the equipment
prepaid to our factory. The equipment will be repaired, replaced or adjusted at our option. The liability of Practical Instrument
Electronics (PIE) is restricted to that given under our guarantee. No responsibility is accepted for damage, loss or other expense
incurred through sale or use of our equipment. Under no condition shall Practical Instrument Electronics, Inc. be liable for any
special, incidental or consequential damage.
841 Holt Road #1 • Webster, NY 14580 Tel: 585-872-9350 • Fax: 585-872-2638 sales@piecal.com • http://www.piecal.com/
Practical Instrument Electronics, Inc. Copyright 2003. All rights reserved.
520/521-9002 2/27/03 3-3
Loading...