Piega TMicro AMT User Manual

User Manual TMicro AMT Loudspeakers

Precautions and Unpacking Procedure

Please read this user manual carefully and pay special attention to the following precautions and warnings.

______________________________________ Unpacking the Loudspeakers

In order to avoid any damage when unpacking the loud­speakers or during the installations, you should always carry
out the work with another person. Before unpacking, remove
any jewelry and watches in order to avoid scratching the
aluminum surface. Procedure: open the carton, remove the
metal brackets on the carton carefully and lift out the
loudspeakers and protective cushions.

Important: PIEGA Loudspeakers have cabinets made from
polished aluminum. When unpacking, handle carefully all times.

Connecting the Loudspeakers

The terminal for single wiring applications is provided at the back of the loudspeakers. This is used for connecting standard loudspeaker
cables with banana plugs or with a lead.

_____________________________________ Connection

Ensure that the electronic components are switched off before
making the connection.

Important:

Ensure the poles are conneccted correctly. A

completely diffuse sound with a weak bass will be produced if
the plus and minus poles are incorrectly connected.

Pass the wires fully through the opening. Fully insert the banana plugs up to the stop.

Daily Use

From development to production, right down to quality testing, PIEGA only uses materials and components of the highest quality. Your
new PIEGA loudspeakers are provided with a polished aluminum surface. Although this material is not very sensitive, it should be
treated with due care.

_____________________________________ Care instructions

Clean the surfaces of the PIEGA loudspeakers with a soft, fluff­free cloth. If necessary use a soft cloth sprayed with a little mild
window cleaner. Never use solvents to clean your PIEGA
loudspeakers. Never use abrasive detergents or any agents
with abrasive ingredients.

_____________________________________ Warnings

Do not remove the front cover. To avoid damage, take great

CONFORMS TO care when children are close to the loudspeakers.
Don’t touch the ribbon tweeter.
UL STD. 6500

CERTIFIED TO
CAN/CSA STD. E60065

PIEGA SA Bahnhofstrasse 29 CH-8810 Horgen [e-mail] www.piega.ch

Manual TMicro Subwoofer MKII

Daily Use
_____________________________________ Precautions and Unpacking Procedure

Ensure particularly that the subwoofer is installed and
connected in accordance with the instructions of this manual.
The TMicro Sub is designed for use in dry residential
environments with a temperature range of 10 …40 C.Refer
servicing exclusively to qualified and Piega authorized service
personnel.

Unpacking: Please pay attention to the same precautions and
warnings as for unpacking the TMicro loudspeakers.

_____________________________________ Terminal area

Many connection options offer a wide number of configurations,
both for stereo and for surround mode. The stereo amplifier
integrated in the subwoofer allows subwoofer, TMicro 3,
TMicro5 to be combined with a flat screen TV, MP3, iPhone,
etc. to produce a really small hi-fi system.

Cinch terminals (L+R) for connecting to the AV-receiver, stereo
amp or MP3-player require connection cables with cinch plugs.

The high level Input terminals (IN) for connecting amplified
music signals can be connected to loudspeaker cables with or
without banana plugs.

The high level Output terminals (OUT) enable satellite
loudspeakers to be connected to the integrated stereo amplifier
of the subwoofer.

Connecting the supply cable: Check wheter the default switch
position (240/120 V) of your subwoofer corresponds to the
standard supply voltage in your country.

Do not switch on the subwoofer (POWER ON) until all cable
connections have been made.

The ‘AUTO’ switch enables the subwoofer to switch on auto­matically as soon as a signal is received. When the switch is in
‘ON’ position, the subwoofer stays permanently switched on.

‘SUB VOL’: Use this knob to adjust the subwoofer volume.
‘VOL’: Use this knob to adjust the volume of the subwoofer and

the bookshelf speakers.
The upper limit frequency of the subwoofer can be adjusted as

required using the ‘Crossover’ knob
Switch Phase 0° / 180°: Phase setting / Phase reverse.
The lower limit frequency can be set with the ‘SAT’ 3-position

slide switch, depending on the size of the loudspeaker used.

Warranty Conditions

The warranty is limited to six years on our loudspeakers and three years on our electronics in accordance with the conditions stated below. Read through
the service and warranty conditions carefully, especially the warnings concerning the purchase of PIEGA loudspeakers from unauthorized dealers.

1. Every Piega device leaves the factory in perfect condition. If any manufacturing and/or material defects are found during normal use of the device, we
warrant to repair the device with free parts and labor during the first six years from the date of purchase.

2. The registration card for the device must be sent to Piega within six weeks of purchase, or registered online via the Internet at
www.piega.ch/en/service/warranty.htm.

3. The product must be purchased from an authorized Piega dealer.

4. The warranty will not be applicable if any repair is carried out by a person or a workshop that is not authorized to do this by Piega.

5. If it is necessary for a device or part of it to be sent to Piega or an approved Piega workshop, the sender is responsible for paying all transport costs in
advance. The original packaging must be used for sending the complete device.

6. The warranty will not be applicable if the serial number of the device has been modified, removed or made illegible. It will also not apply if the device is
not connected properly or not treated with due care. The warranty will also not be applicable if the device was modified or repaired in any way that in
our view has altered the correct functioning of the device.

7. Piega shall not be liable for the consequences of any damage.
PIEGA Loudspeaker products from unauthorized dealers:

The official PIEGA warranty becomes invalid if a PIEGA loudspeaker product was purchased from an unauthorized dealer and is therefore a gray market
product, or if the original serial number has been intentionally removed, replaced or made illegible. Should you have any doubt that the dealer you have
selected is an officially authorized PIEGA dealer, we recommend that you contact us or the PIEGA sales organization in your country without fail. Please
note the PIEGA sales policy statement at www.piega.ch. Subject to modifications, in particular technical modifications and errors. 2017

PIEGA SA Bahnhofstrasse 29 CH-8810 Horgen [e-mail] www.piega.ch