Picotest Corp M3500A Users Guide

p

T

p

M3500-OPT08

4 WIRED TEST LEADS

(Needle Type)

USER’S GUIDE

August 2008 Version 2 Printed

in Taiwan

PICOTEST CORP.

8F-1, 286-9, Hsin-Ya Rd., 80673,
Kaoshiung, Taiwan
TEL: [phone]
FAX: [phone]
URL

http://www.picotest.com.tw

Product Introduction

PICOTEST thanks you to purchase the
“Model M3500-OPT08 4 Wired T est Leads” .
To reach the best performance from the
product, please read this guide carefully.

1. Overview

The M3500-OPT08 4 Wired Test Leads
have a four-terminal structure that can be
used in wide areas.

2. Inspection & Upkeep

Inspection:

When you open the package, inspect it
carefully to make sure whether defects
occurred in the appearance or
malfunction in the operation. Please
contact with your local reseller or
PICOTEST representative for more help.

Upkeep:

T o clean the product, wipe it gently with a
soft and moistened cloth. Prevent using

solvents, such as benzene, alcohol,
acetone, ether, ketones, thinners or
gasoline because of their destructive
capabilities.

3. Safety

This safety information with the
warning and danger marks on the
user’s guide reminds users to avoid
risks as they are using it.

Warning: The triangle symbol in
black indicates that incorrect operation
might cause an injury to users or
damage to the product.

Danger: The triangle symbol in
red indicates that incorrect operation
might cause an extreme hazard to
users’ life.

4. Prenotion

Danger

z To avoid electrical shock and

personal injury, please don’t
measure the source out of
specification.
z The maximum rated voltage
between input terminals and
ground is 33 Vrms, 46.7 Vp AC and
70 V DC. In addition,
in

the maximum

ut current is 5A AC/DC.

Warning

z

o avoid bending or pulling the
product, please be careful with it
when measurement is executed.
z To avoid the sharp injury by the
ends of the leads, the protective pin
caps are necessary to be covered
when the leads are not used.

Note: The caps are placed on pins for
protection during transport. Please
remove the caps before use.

5. Specifications

Maximum Rated
Voltage to Earth
Maximum Input
Current
Operating
Temperature and
Humidity
Storage
Temperature And
Humidity
Operating
Environment
Dimension &
Weight
Accessories User Guide

6. Procedure

Danger

Before using the leads, please make
sure that the insulation on the leads is
safe, and the conductors are not
exposed. If the mentioned concerns
appear, kindly contact with your local
reseller or Picotest representative for
more hel

A. Make sure that power of the

output source device is turned off.

B. Connect M3500-OPT08 4 Wired

Test Leads to the input terminal of
the power-on device as shown as
Figure-1.

C. Configure your meter to a proper

function.

D. Turn on the power of the output

source device.

E. Use the probes to measure the

source.

F. Put the caps on the probes after

using.

Less than 30 Vrms or 42 Vp
AC or 60 Vdc
AC/DC 5 A Continuous

0°C to 40°C (32°F to 104°F),
80% RH Or Less (No
Condensation)

-10°C to 50°C (14°F to
122°F), 80% RH Or Less (No
Condensation)
Altitude Up to 2000 M (6562
Feet), Indoors
Approx. 155 cm / Approx.
180 g

.

7. Part Names

The part names and the detailed
dimension of the Model M3500-OPT08
Wired Lead are in the following Figure-2,
Figure-3 and Figure-4.

z Input HI (BROWN) & Sense HI (RED)

z Input L O (ORANGE) & Sense LO (YELL OW)

z Enlarged View of Pin

Figure-1

Figure-2

Figure-3

Figure-4