Quick Operation Guide
Tire Pressure Monitoring System
(TPMS)
Technical Support
• Push ”Reset” button, can recover
the preset status
• For downloading the manual and
more information, please visit
http://www.picolink.com.tw
TPMS Warranty Card
Model No. P11x
Serial
No.
Picolink
Model No.: P11x
Purchase
Date
Agent
Signature
Y M D
Parts Photo Q`TY Parts Photo Q`TY
Display ExplanationPacking Contents
Display
Unit
Display
Unit
Stand
3M VHB
Tapes
Metal
Valve
1
1
1
4
Power
Cable
(P111)
Screw
With
Washer
Transmi-
tter
Power
Cable
(P112)
1
4
4
1
Bad Signal Battery/Generator
Tire-leaking
Transmitter
Low-Voltage
Warning
Battery/Genera
tor Voltage
Temperature Unit
Tire Pressure &
Temperature
Tire Pressure
Normal Tire
Abnormal Tire
1. Transmitter Installation
a. The Photos Of Structures
b. Installation Process
1. Unload tire/valve from steel wheel
2. Clean the dirt of steel wheel and
valve at their edges
3. Put the valve through the hole of
steel wheel with washer and use
4 Nm torque to tighten the valve
4. To adjust the Transmitter to become
vertical with the steel wheel. And use
2.2 Nm torque to tighten the screw
on the transmitter
5. Please proceed from Step 1 to Step 6
Step1: Take off 4 tires and mark
Step 2: Take No.1(RF) tire and put the
No.1～No.4 as the tire position.
No.4 = Left Front (LF) ; No.1 = Right Front (RF)
No.3 = Left Rear (LR) ; No.2 = Right Rear (RR)
No.4
LF
No.1
RF
metal valve to the valve hole
from “inside of the steel wheel”.
No.3
LR
No.2
RR
Step 4: Put the washer to the valve from
Step 3: To adjust the valve to become
vertical with the steel wheel.
“outside of the steel wheel”. Use
torque wrench and hexagon
wrench to set 4 Nm ( 40.8 kg．cm)
torque to tighten the screw on the
transmitter.
Step 5: Put transmitter in the valve and
Step 6: In turns to proceed No. 2 -> 3
make the angle of the transmitter
unit as flat as the steel wheel.
And set 2.2 Nm ( 22.4kg ．cm)
torque to tighten the screw.
-> 4 transmitter and repeat the
action from Step 1 to Step 5.
Finally to proceed the tire
balance correction.
2. Receiver Installation
a. Install display and its stand.
b. Use 3M VHB tapes to paste the stand
to the position you choose at the console.
c. Plug the power cable with micro-USB
beside the receiver.
d. (Model No.: P112) Put the car charger
connecter into the its socket.
e. Adjust the right angle of the stand
in order not to influence the driving.
Finish the installation and start
using this TPMS.
Note: (Model No.: P111) Put the red wire of
the power cable with fuse box and
the black wire with the ground.
3. System Specification
a. Receiver Specification
Operation Voltage
Channel Quantity
Demodulation
Storage Temp.
Operation Temp.
Weight
Dimension
DC 5V
1 channel
-40℃℃℃℃ ~ +125℃℃℃℃
-25℃℃℃℃ ~ +75℃℃℃℃
85*55*14 (mm)
FSK
70 g
b. Transmitter Specification
Operation Voltage DC 3V
Channel Quantity 1 channel
Modulation FSK
Occupied BW Max. 1MHz
Frequency 433.92 MHz
RF power Max. 80 dBμμμμV/m
Storage Temp.
-40℃℃℃℃ ~ +85℃℃℃℃
Operation Temp.
Pressure Range 0~80 psi
Pressure Accuracy
Temp. Accuracy
Battery Life 5~7 years
Weight
Dimension 58*29*19 (mm)
-30℃℃℃℃ ~ +85℃℃℃℃
± 1 psi
± 3℃℃℃℃
25 g ± 2 g
Loading...