FASTCAM-PCI
Hardware Manual
Rev.2.2
PHOTRON LIMITED
2001
FASTCAM-PCI Series Hardware Manual
Table of contents
Chapter 1 - General Information
Introduction 1.1
Warranty 1.2
How to Use This Manual 1.3
Precautions 1.4
Chapter2 - Getting Ready
Introduction 2.1
About the Packing 2.1.1.
Accessories and optional items 2.1.2.
About the FASTCAM-PCI Set 2.2
Processor board 2.2.1
Camera head 2.2.2
Accessories 2.2.3
Connector Specifications 2.2.4
Installation of Hardware 2.3
Installation of main PCI board 2.3.1
Installation of camera head 2.3.2
Adding Memory 2.3.3
Setting for multi-camera sync 2.3.4
Chapter 3 - Specifications
Hardware specifications 3.1
Dimensions 3.2
Care of lenses 3.3
- 2 -
FASTCAM-PCI Series Hardware Manual
Chapter 1 General Information
1.1.Introduction
1.2.Warranty
1.3.How to Use This Manual
1.4.Precautions
- 3 -
FASTCAM-PCI Series Hardware Manual
1.1. Introduction
The FASTCAM-PCI High-Speed Video Camera System has been developed to offer a powerful
engineering solution in R and D, engineering, manufacturing, quality control in general industries
and special applications in scientific, medical, biological, aerospace studies. Its extra-high-speed
recording capability and easy-to-use remote control software provide a motion analysis
environment that has been hard to obtain so far.
The live image setup function ensures that the image of the object on the screen is captured
and recorded in the memory at a simple press on the recording button. You do not have to set the
exposure and image layout on the screen by guessing: all you see on the monitor screen is what
you get recorded at a press on the recording button. Use this cutting-edge recording technology to
observe your fast moving object as a slow-motion playback image or to input the moving image
data into your motion analysis system for processing.
This manual has been prepared for you to use the system in the most effective way for
slow-motion observation and motion analysis of fast moving objects.
Remarks:
1. For the best use of the system, please read through this manual.
2. The content of this manual is based on the best knowledge of the manufacturer. However, in
case any error or missed information is found in this manual, please inform the manufacturer of
such shortcomings. Notwithstanding the above, the manufacturer is not responsible for any results
of the use of this equipment.
3. Copying all or any part of this manual without permission is prohibited.
4. The content of this manual may be changed any time without prior notice.
5. The manufacturer assumes no responsibility for any direct or indirect damage or loss of profit
resulting from the use of this equipment
6. The manufacturer assumes no responsibility for any result of the use of this equipment.
7. Copying all or any part of the software included in this system without prior written permission by
the author is an infringement of copyright.
- 4 -
FASTCAM-PCI Series Hardware Manual
1.2. Warranty
New Equipment Warranty
PHOTRON FASTCAM-PCI
PHOTRON LIMITED warrants this PHOTRON FASTCAM-PCI series and accessories
manufactured by PHOTRON LIMITED, to function properly for one year from the date of shipment,
if the warranty registration card was filled out and returned to PHOTRON USA, INC. or PHOTRON
EUROPE LIMITED within thirty days of shipment.
PHOTRON LIMITED, in conjunction with PHOTRON USA,INC. or PHOTRON EUROPE LIMITED,
agrees to perform the following equipment warranty services:
1. Repair service: If shipped to PHOTRON at any of the addresses shown below, repairs will
be made at no charge.
2. Parts replacement: Replacement parts installed under warranty will be provided at no
charge.
THIS WARRANTY DOES NOT APPLY UNDER THE FOLLOWING CONDITIONS:
Failure to operate the PHOTRON FASTCAM-PCI series in accordance with Photon’s written
instructions, including environmental specifications listed in the User’s Manual.
If there is evidence of the PHOTRON FASTCAM-PCI series being subjected to accidental damage,
misuse or abuse.
If the PHOTRON FASTCAM-PCI series has been repaired or tampered with by persons other than
PHOTRON personnel, customer personnel trained by PHOTRON or without permission of
PHOTRON.
Shipping damage is not covered by this warranty. The purchaser has the responsibility to place a
claim of damage in shipment with the carrier.
PHOTRON LIMITED makes no other warranties, express or implied, including the implied
warranties of merchantability and fitness for a particular purpose. If this PHOTRON
FASTCAM-PCI series does not function properly during the warranty period, PHOTRON LIMITED
will repair it without charge according to the terms stated above. Repair without charge is
PHOTRON LIMITED’s only obligation under this warranty. PHOTRON LIMITED, PHOTRON
USA, INC.or PHOTRON EUROPE LIMITED will not be responsible for any consequential or
incidental damages resulting from the sale, use or improper functioning of this equipment even if
loss or damage is caused by the negligence or other fault of PHOTRON LIMITED, PHOTRON
USA, INC.or PHOTRON EUROPE LIMITED.
Return the equipment that needs warranty service to:
In Americas
PHOTRON USA,INC.
9520 Padgett Street, Suite
110
San Diego,CA
92126-4446,USA
Phone: 858-684-3555
Fax: 858-684-3558
E-mail:image@photron.com
[In Europe:
PHOTRON EUROPE
LIMITED
Willowbank House
84 Station Road
Marlow, Bucks SL7, U.K
Phone:+44(0) 1628 89 4353
Fax: +44(0) 1628 89 4354
E-mail:image@photron.com
In other areas:
PHOTRON LIMITED
Shibuya 1-9-8,Shibuya-ku
Tokyo 150-0002,Japan
Phone:+81 3 3486 3471
Fax: +81 3 3486 8760
E-mail:image@photron.com
- 5 -
FASTCAM-PCI Series Hardware Manual
1.3. How to Use This Manual
DEFINITION OF TERMS
You will notice as you read this manual that some of the information is presented as a NOTE,
CAUTION or WARNING. It is important that you understand the significance of these three
terms.
NOTE
A note contains information that we wish to emphasize regarding the operation of your
FASTCAM-PCI series.
CAUTION
A caution is intended to warn you that a certain operation or condition may cause harm to your
FASTCAM-PCI series.
WARNING
A warning is important to the safety of everyone operating the FASTCAM-PCI series and should
not be disregarded under any circumstances.
Chapter 1, general information
Contains the Warranty, precautions, introduction and how to use this manual.
Chapter 2, getting ready
An introduction to the components of your FASTCAM-PCI series. Explains the use of each
connector and control on the Camera and the Processor.
Chapter 3, specifications
Contains specifications.
If you require additional information not included in this manual regarding the care, technical
service and operation of your FASTCAM-PCI series please contact the service department in San
Diego by calling:
800 - 585 - 2129
- 6 -
FASTCAM-PCI Series Hardware Manual
1.4. Precautions
AMBIENT Temperature
Photron FASTCAM-PCI has been designed to work properly in an ambient temperature range of 0
to 35 degrees Celsius (32 to 95 degrees Fahrenheit), no condensation.
STORAGE Temperature
FASTCAM-PCI must be stored in a place with an ambient temperature range of -20 to +70
degrees Celsius (-4 to +158 degrees Fahrenheit), no condensation.
TRANSPORTATION
Save the original carton the unit came in for future transportation. Or, if you transport the unit
frequently, the use of a special carrying case is recommended. Please check with your dealer,
Photron USA or Photron Europe. Do not send the unit to a place where the temperature can go
below -20 degrees Celsius (-4 degrees Fahrenheit) or above 70 degrees Celsius (+158 degrees
Fahrenheit).
FEDERAL COMMUNICATIONS COMMISSION
STATEMENTS
WARNING: This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instruction manual, may cause interference to radio
communications. It has been tested and found to comply with the limits for a Class 鄭・
computing device pursuant to Subpart B of Part 15 of the FCC Rules and VDE 0871 Class 釘・
which are designed to provide reasonable protection against such interference when operated in a
commercial environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever measures
may be required to correct the interference.
This device complies with Part 15 of the FCC Rules and VDE 0871. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received including interference that may cause undesired operation.
WARNING
This product is grounded through the power cord. This protective ground connection is essential
for safe operation of the equipment. Avoid electrical shock by plugging the power cord into a
properly wired receptacle. A loss of the protective ground, for any reason, could result in
electrical shock. Use the proper power cord and insure that it is in good condition.
- 7 -
FASTCAM-PCI Series Hardware Manual
Chapter 2 Getting Ready
2.1. Introductions
2.2. About the FASTCAM-PCI set
2.3. Installation of hardware
- 8 -
FASTCAM-PCI Series Hardware Manual
2.1. Introductions
2.1.1. About the packing
This product consists of the following items. Unpack and make sure if all the items are included.
1. Camera head (with a 6-meter cable) 1 ea.
2. PCI board 1 ea.
3. Lens mount cap 1 ea.
4. Internal sync/trigger signal cable
With IL connector 2Pin- 2Pin, 50 mm 1 ea.
5. Board driver /Application set-up disk CD-ROM 1 ea.
6. Hardware manual 1 ea.
7. FASTCAM Control Software Operation Manual 1 ea.
8. Warranty card 1 ea.
2.1.2. Accessories and optional items
The FASTCAM-PCI offers the following optional items:
543-frame expansion memory module
16m Imager cable option
- 9 -
FASTCAM-PCI Series Hardware Manual
2.2. About the FASTCAM-PCI Set
The FASTCAM-PCI consists of a processor board, camera head and a set of control software. Up
to four processor boards, complying with the ATX standard can be installed in the PC.
2.2.1. Processor board
+
+
+
+
240
161
160
121
12061
60
1
SLOT‑4 SLOT‑3 SLOT‑2 SLOT‑1
MADE IN JAPAN
PHOTRON Ltd.
PCITMEM‑991005
PCITPOW‑991005
+
+
312mm (12.28inch)
106.5mm
(4.2inch)
FASTCAM-PCI Main Board
FASTCA M-PCI Memory Board
Memory Expansion Slots
EXT OUT Connec tor
SYNC IN Connect or
Camera Connecto r
- 10 -
FASTCAM-PCI Series Hardware Manual
2.2.2. Camera head
Imager
C Mount
FASTCAM-PCI Imager
Camera Connector
C amera cable (6 m)
2.2.3. Accessories
EXT OUT/ SYNC IN Cables
1. OUT1
2. OUT2
3. T- TTL
4. T- SW
PUSH
PULL
Connector
PUSH
PULL
Connector
- 11 -
FASTCAM-PCI Series Hardware Manual
2.2.4. Connectors Specifications
The FASTCAM-PCI supports the following input and output signals.
+
1. OUT1
2. OUT2
3. T- TTL
4. T- SW
1 EXTOUT1 Output connector
A BNC connector for an output signal that specifies the first frame when a non-sync reset trigger
signal is used.
2 EXTOUT2 Output connector
A BNC connector for an output vertical sync signal for sync operation with strobe and/or pulsed
laser units.
3 TRIGGER TTL IN Input connector
A BNC connector for TTL compatible signal that controls start and end of recording in a selected
recording mode. The input signal is +5 volt positive and the pulse width should be over 50
microseconds.
4 TRIGGER SW IN Input connector
Switch contact between the shield and the center conductors of the BNC connector controls start
and end of a recording in a selected recording mode.
- 12 -
FASTCAM-PCI Series Hardware Manual
TRIGGER TTL IN Input connector
TRIGGER IN
TRIGGER START
5V TTL level
Photocoupler
TLP 521(T OSHIBA)
CPU I/O Port
GND
330
+5V
TRIGGER SW IN Input connector
TRIGGER IN
TRIGGER START
220
CPU I/O Port
GND
330
+5V
- 13 -
FASTCAM-PCI Series Hardware Manual
5. V SYNC IN
6. V SYNC OUT
7. I NTERNAL TRIGGER IN
8. I NTERNAL TRIGGER OUT
5. V SYNC INPUT Connector (VSI Connector)
When multiple FASTCAM-PCIs are set on one single PC, sync signal between cameras is input
via this connector. It does not support external connection or synchronization. The sync signal is
+3.3 volt TTL level, negative.
6. V SYNC OUTPUT Connector (VSO Connector)
When multiple FASTCAM-PCIs are set on one single PC, sync signal between cameras is sent out
via this connector. It does not support external connection or synchronization. The sync signal is
+3.3 volt TTL level, negative.
7. INTERNAL TRIGGER INPUT Connector (TRI Connector)
In multi-camera recording operation, the trigger signal from the master camera is fed to slave
camera(s) via this connector for sync recording with the master camera.
8 INTERNAL TRIGGER OUTPUT Connector
In multi-camera recording operation, the trigger signal from the software is fed to slave camera(s)
via this connector for software-controlled sync recording with the master camera.
8. INTERNAL TRIGGER OUTPUT Connector (TRO Connector)
In multi-camera recording operation, the trigger signal from the software is fed to slave camera(s)
via this connector for software-controlled sync recording with the master camera.
- 14 -
FASTCAM-PCI Series Hardware Manual
2.3. Installation of hardware
Caution
Shut down the computer when you connect the camera head and PCI board. Also, shut down the
computer when you install a PCI board into a computer slot. If you do not shut down the computer
when installing the PCI board or camera, it may cause defect or damage on them. Please see if
there is no excessive twist of cables.
2.3.1. Installing the main PCI board
2.3.2. Installing the camera head
2.3.3. Adding Memory
2.3.4. Setting for multi-camera sync
- 15 -
FASTCAM-PCI Series Hardware Manual
2.3.1. Installing the main PCI board
Follow the procedure below to install the PCI board.
1. Be sure to shut down the computer and unplug from the power outlet.
2. Remove the top cover of the computer following the instructions given in the computer’s
manual.
3. Make sure there is an empty slot for a PCI board.
4. Remove the cover plate on the back of the computer housing corresponding to the slot where
you are going to insert the PCI board.
5. Insert the PCI board into the slot. Press the board firmly until it completely sits in the slot.
Fasten the retaining screws on the back of the computer housing.
6. Connect the camera cable to the PCI board. Make sure if the connector’s orientation is correct,
and fasten the retaining screws firmly. Double check if the connectors are firmly engaged and
retained.
7. Replace the top cover of the computer and fasten retaining screws following the instructions of
the computer manual.
2.3.2. Installing the camera head
8. Connect the connector on the camera cable to the camera connector of the PCI board.
Warning:
Please be sure to unplug the power connector from the power outlet before installing the PCI
board in the PC.
- 16 -
FASTCAM-PCI Series Hardware Manual
2.3.3. Adding Memory
Up to four memory modules of 128MB capacity can be added to a PCI board.
1. Shut down the computer and unplugs the power cord from the power outlet. Open up the PC
enclosure and remove the PCI board from the PC.
2. Remove the retaining screws that fasten the PCI Memory board to the PCI Main board. Be
careful when removing the connectors.
ネジ
1
+
+
+
+
+
+
++
240
161
160
121
12061
60
1
SLOT‑4 SLOT‑3 SLOT‑2 SLOT‑1
MADE IN JAPAN
PHOTRON Ltd.
PCITMEM‑991005
ＳＬＯＴ１ＳＬＯＴ２ＳＬＯＴ３ＳＬＯＴ４
ネジ ネジ
ネジ ネジ
ネジ
ネジ
1
+
+
+
+
+
+
++
240
161
160
121
12061
60
1
SLOT‑4 SLOT‑3 SLOT‑2 SLOT‑1
MADE IN JAPAN
PHOTRON Ltd.
PCITMEM‑991005
ＳＬＯＴ１ＳＬＯＴ２ＳＬＯＴ３ＳＬＯＴ４
ネジ ネジ
ネジ ネジ
ネジ
Screw
Screw
Screw
Screw
ScrewScrew
3. Install SO-DIMM memory module(s) onto the PCI Memory board. Use SLOT 1 first and then
other slots in the order as numbered. DO NOT skip any slot between additional memory modules.
Align the memory modules in the same orientation and see if they are firmly inserted in the slot.
- 17 -
FASTCAM-PCI Series Hardware Manual
4. Setting dip switches on PCI main board
１
２
３
４５
６７８
ON
Dip Sw itches
Dipswitches 1 to 4 are for activating the additional memory modules. Reset the dipswitches to
match the number of added memory modules looking at the table below.
Note: Dipswitches 5 to 8 are factory set. Please do not disturb them, or they may cause
malfunctioning of the camera.
Setting
Dipswitch setting
Number of memory
Modules
1 2 3 4
1 (128 M Byte) ON OFF OFF OFF
2 (256 M Byte) ON ON OFF OFF
3 (384 M Byte) ON ON ON OFF
4 (512 M Byte) ON ON ON ON
ON: Move SW upward OFF: Move SW downward
Match the number of added memory modules and dipswitch setting correctly, or the system may
fail to capture and record images properly.
5. Connecting between PCI main board and memory modules
Make sure the connectors are firmly engaged to their entire depth. Redo the rataining screws to
fasten the board firmly.
6. Install the PCI board in the PC following the instructions given in section 2.3.1.
- 18 -
FASTCAM-PCI Series Hardware Manual
2.3.4. Setting for multi-camera sync
By setting the PCI main board for external sync mode, multi-camera operation can be performed.
In the multi-camera operation mode, two, three or four cameras are hooked up to one computer
and run in synchronization with each other to record the image of a common object from different
view points along one single time line. This is a useful feature for an application where behavior of
a single, or two or more objects, is observed from different perspectives. To activate this mode,
resetting of jumpers on the PCI main board is necessary. First, remove the PCI main board from
the computer, then remove the PCITMEM (memory) board from the PCI main board to expose the
jumpers. Follow the instructions given in section 2.3.3. (Adding Memory Board) to carry out this
resting of jumpers.
V SYNC IN (VSI)
V SYNC OUT (VSO)
INTERNAL TRIGGER IN ( TRI)
INTE RNAL TRIGGER OUT (TR O)
Jumper Posts
1
2
・TRI Connector
Imports internal trigger signals from TRO connector of other boards.
・TRO Connector
Outputs trigger signals internally generated in the board.
・VSI Connector
Imports external sync signals from VSO connector of other boards.
・VSO Connector
Outputs external sync signals
・Jumper posts for external sync signal setting
These jumper posts are used to set for sync operation mode.
Master Mode
The PCI board that is set as the Master board outputs
internally generated sync signals from the VSO
connector. It also outputs the trigger signals given by
the software from the TRO connector.
Jumper setting Open
Slave Mode Once the PCI main board is set in the slave mode, the
camera operates in sync with the sync signal imported
via the VSI connector.Recording starts at the trigger
signal input via the TRI connector.
Jumper setting: Short
- 19 -
FASTCAM-PCI Series Hardware Manual
Cable connection for 4-cameras sync operation
*Hardware setting:
1st Camera (Ma ster)
VSO TRO VSI TRI
2nd Camera (Slave) VSO TRO VSI TRI
3rd Camera (Slave) VSO TRO VSI TRI
4th Camera (Slave) VSO TRO VSI TRI
:Sync cables and Internal trigger signal cables
*Please contact P hotron to purchase FASTCAM original sync signal cables.
50 millimeters long
IL Connector, 2 pins IL Connector, 2 pins
IL-G-2S-S3C2 IL-G-2S-S3C2
(Jum per)
*Application Software Setting
Software must be properly reset for the cameras to operate in sync mode.
In the sync operation mode, one of the cameras must be set to master mode while others are set
to slave mode. For the cameras that are to follow the master, check the “Ext sync In” box in the
camera setup menu from the “More” button. Do not check the “Ext sync In” box for the camera that
is the master, or the cameras will not work.
- 20 -
FASTCAM-PCI Series Hardware Manual
*Triggering for sync recording
Note:
Triggering from software:
All cameras are triggered without delay by a trigger signal distributed via the internal harness.
Triggering from external source:
A common externally generated trigger signal must be input to each PCI board via EXT SYNC IN
connector. A trigger signal input to one PCI board only will not be passed on to other PCI boards.
- 21 -
FASTCAM-PCI Series Hardware Manual
Chapter 3 Specifications
3.1. Hardware Specifications
3.2. Dimensions
3.3. Care of Lenses
- 22 -
FASTCAM-PCI Series Hardware Manual
3.1. Hardware Specifications
Table1: Overall Functions Specification
Lens mount C mount
Imaging sensor Progressive scan 1/3-inch CCD, square pixels
Recording media IC memory (SD-RAM)
Recording capacity
128MB: 543 full frames, 2.2 seconds
256MB: 1,087 full frames, 4.3 seconds
384MB: 1,631 full frames, 6.5 seconds
512MB: 2,175 full frames, 8.7 seconds
Full frame: 30, 60, 125, 250 fps
Partial frame: 500, 1000, 2000, 3000, 5000, 10000 fps
Framing rates
Frame rate availability dependant on model
Full frame: 512 x 480 pixels
Partial frame:
512 x 240; 256 x 240; 256 x 120 pixels
128 x 120; 128 x 80; 128 x 34 pixels
Pixel resolution
Note: Pixel resolution depends on framing rate (see Table 3).
Grayscale
Monochrome: 8 bits (256 steps)
Color: R, G, B 8 bits each (24 bits color, 256 steps)
Playback rates 1, 2, 4, 8, 15, 30 fps
1/frame rate; 1/500; 1/1000; 1/2000; 1/3000; 1/5000;1/10000;
1/20000; 1/40000; 1/65000; 1/80000;1/100000; 1/120000 second
Electronic shutter
Note: Shutter speed availability depends on framing rate (see
Table 4).
Trigger input (TTL)
Trigger input
TTL +5 V positive going
(Contact) Switch contact Sync output
Sync Output
Vertical sync signal (master) to drive other FASTCAM-PCI slaves
boards
(Negative 3.3 Vp-p)
Sync input Vertical sync signal (negative 3.3 Vp-p)
Output signal 1 Vertical sync output+5V TTL, negative
Output signal 2 Asynchronous random reset timing signal +5V TTL, positive
Power From the PCI bus (+3.3V; +5.0V; -12V)
Ambient temperature
Power consumption
0 to 35 degrees Celsius (32 to 95 F), no condensation
+3.3 V: 2 A; +5.0 V: 2 A; -12 V: 0.5 A (32.6 watts)
Camera head: 160(6.3") W x 330(13")D x 180(7.1")H mm
Dimensions
PCI board: 312(12.6") W x 106(4.2")H x 16(0.6")T mm
(PCI full size standard)
Weight Camera head: 1.1 kg (2.4 lbs) (including 6-meter camera cable)
- 23 -
FASTCAM-PCI Series Hardware Manual
Table 2: Framing Rate/Model
Model
Framing Rate
FPS
FASTCAM-PCI
500
FASTCAM-PCI
1k
FASTCAM-PCI
2k
FASTCAM-PCI
10k
30 O O O O
60 O O O O
125 O O O O
250 O O O O
500 O O O O
1000 O NA O O
2000 O NA NA O
3000 NA NA NA O
5000 NA NA NA O
10000 NA NA NA O
Table 3: Frame Rate/Frame Size
Framing
Rate
Image size
(FPS) 512x480 512x240 256x240 256x120 128x120 128x80 128x34
30 O O O O O O O
60 O O O O O O O
125 O O O O O O O
250 O O O O O O O
500 O O O O O O
1000 O O O O O
2000 O O O O
3000 O O O
5000 O O
10000 O
- 24 -
FASTCAM-PCI Series Hardware Manual
Table 4 Shutter Speed/Frame Rate
30
FPS
60
FPS
125
FPS
250
FPS
500
FPS
1000
FPS
2000
FPS
3000
FPS
5000
FPS
10,000
FPS
1/30
1/60 1/60
1/125 1/125 1/125
1/250 1/250 1/250 1/250
1/500 1/500 1/500 1/500 1/500
1/1000 1/1000 1/1000 1/1000 1/1000 1/1000
1/2000 1/2000 1/2000 1/2000 1/2000 1/2000 1/2000
1/3000 1/3000 1/3000 1/3000 1/3000 1/3000 1/3000 1/3000
1/5000 1/5000 1/5000 1/5000 1/5000 1/5000 1/5000 1/5000 1/5000
1/10000 1/10000 1/10000 1/10000 1/10000 1/10000 1/10000 1/10000 1/10000 1/10000
1/20000 1/20000 1/20000 1/20000 1/20000 1/20000 1/20000 1/20000 1/20000 1/20000
1/40000 1/40000 1/40000 1/30000 1/30000 1/40000 1/40000 1/40000 1/40000 1/40000
1/60000 1/60000 1/60000 1/60000 1/65000 1/60000 1/60000
1/100000 1/80000 1/80000
1/120000 1/120000
- 25 -
FASTCAM-PCI Series Hardware Manual
Table5: Number of Frames/Recording Time
Recording Time and Number of Recorded Frames (30FPS)
Memory/Recording Time and Number of Recorded Frames
128MByte 256MByte 384MByte 512MByte
（FPS） Resolution
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
512x480 543 18.1 1087 36.2 1631 54.4 2175 72.5
512x240 1091 36.4 2183 72.8 3275 109.2 4367 145.6
256x240 2183 72.8 4367 145.6 6551 218.4 8735 291.2
256x120 4367 145.6 8735 291.2 13103 436.8 17471 582.4
128x120 8735 291.2 17471 582.4 26207 873.6 34943 1164.8
128x 80 13103 436.8 26207 873.6 39311 1310.4 52415 1747.2
30
128x 34 30839 1028.0 61679 2056.0 92519 3084.0 123359 4112.0
Recording Time and Number of Recorded Frames (60FPS)
Memory/Recording Time and Number of Recorded Frames
128MByte 256MByte 384MByte 512MByte
（FPS) Resolutions
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
512x480 543 9.1 1087 18.1 1631 27.2 2175 36.3
512x240 1091 18.2 2183 36.4 3275 54.6 4367 72.8
256x240 2183 36.4 4367 72.8 6551 109.2 8735 145.6
256x120 4367 72.8 8735 145.6 13103 218.4 17471 291.2
128x120 8735 145.6 17471 291.2 26207 436.8 34943 582.4
128x 80 13103 218.4 26207 436.8 39311 655.2 52415 873.6
60
128x 34 30839 514.0 61679 1028.0 92519 1542.0 123359 2056.0
Recording Time and Number of Recorded Frames (125FPS)
Memory/Recording Time and Number of Recorded Frames
128MByte 256MByte 384MByte 512MByte
（FPS)
Resolutions
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
512x480 543 4.4 1087 8.7 1631 13.0 2175 17.4
512x240 1091 8.7 2183 17.5 3275 26.2 4367 34.9
256x240 2183 17.5 4367 34.9 6551 52.4 8735 69.9
256x120 4367 34.9 8735 69.9 13103 104.8 17471 139.8
128x120 8735 69.9 17471 139.8 26207 209.7 34943 279.5
128x 80 13103 104.8 26207 209.7 39311 314.5 52415 419.3
125
128x 34 30839 246.7 61679 493.4 92519 740.2 123359 986.9
- 26 -
FASTCAM-PCI Series Hardware Manual
Recording Time and Number of Recorded Frames (250FPS)
Memory/Recording Time and Number of Recorded Frames
128MByte 256MByte 384MByte 512MByte
（FPS) Resolutions
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
512x480 543 2.2 1087 4.3 1631 6.5 2175 8.7
512x240 1091 4.4 2183 8.7 3275 13.1 4367 17.5
256x240 2183 8.7 4367 17.5 6551 26.2 8735 34.9
256x120 4367 17.5 8735 34.9 13103 52.4 17471 69.9
128x120 8735 34.9 17471 69.9 26207 104.8 34943 139.8
128x 80 13103 52.4 26207 104.8 39311 157.2 52415 209.7
250
128x 34 30839 123.4 61679 246.7 92519 370.1 123359 493.4
Recording Time and Number of Recorded Frames (500FPS)
Memory/Recording Time and Number of Recorded Frames
128MByte 256MByte 384MByte 512MByte
（FPS) Resolutions
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
512x240 1091 2.2 2183 4.4 3275 6.6 4367 8.7
256x240 2183 4.4 4367 8.7 6551 13.1 8735 17.5
256x120 4367 8.7 8735 17.5 13103 26.2 17471 34.9
128x120 8735 17.5 17471 34.9 26207 52.4 34943 69.9
128x 80 13103 26.2 26207 52.4 39311 78.6 52415 104.8
500
128x 34 30839 61.7 61679 123.4 92519 185.0 123359 246.7
Recording Time and Number of Recorded Frames (1000FPS)
Memory/Recording Time and Number of Recorded Frames
128MByte 256MByte 384MByte 512MByte
（FPS) Resolutions
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
256x240 2183 2.2 4367 4.4 6551 6.6 8735 8.7
256x120 4367 4.4 8735 8.7 13103 13.1 17471 17.5
128x120 8735 8.7 17471 17.5 26207 26.2 34943 34.9
128x 80 13103 13.1 26207 26.2 39311 39.3 52415 52.4
1000
128x 34 30839 30.8 61679 61.7 92519 92.5 123359 123.4
- 27 -
FASTCAM-PCI Series Hardware Manual
Recording Time and Number of Recorded Frames (2000FPS)
Memory/Recording Time and Number of Recorded Frames
128MByte 256MByte 384MByte 512MByte
（FPS) Resolutions
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
256x120 4367 2.2 8735 4.4 13103 6.6 17471 8.7
128x120 8735 4.4 17471 8.7 26207 13.1 34943 17.5
128x 80 13103 6.6 26207 13.1 39311 19.7 52415 26.2
2000
128x 34 30839 15.4 61679 30.8 92519 46.3 123359 61.7
Recording Time and Number of Recorded Frames (3000FPS)
Memory/Recording Time and Number of Recorded Frames
128MByte 256MByte 384MByte 512MByte
（FPS) Resolutions
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
128x120 8735 2.9 17471 5.8 26207 8.7 34943 11.6
128x 80 13103 4.4 26207 8.7 39311 13.1 52415 17.5
3000
128x 34 30839 10.3 61679 20.6 92519 30.8 123359 41.1
Recording Time and Number of Recorded Frames (5000FPS)
Memory/Recording Time and Number of Recorded Frames
128MByte 256MByte 384MByte 512MByte
（FPS) Resolutions
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
128x 80 13103 2.6 26207 5.2 39311 7.9 52415 10.5
5000
128x 34 30839 6.2 61679 12.3 92519 18.5 123359 24.7
Recording Time and Number of Recorded Frames (10,000FPS)
Memory/Recording Time and Number of Recorded Frames
128MByte 256MByte 384MByte 512MByte
（FPS) Resolutions
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
Number
of
Recorded
Frames
Recording
time (sec)
10000 128x 34 30839 3.1 61679 6.2 92519 9.3 123359 12.3
- 28 -
FASTCAM-PCI Series Hardware Manual
3.2. Dimensions
3.2.1. Imager: (mm)
50 .8
14 14
6.5
50 .8 114 41
56 .75
1/4 inch
2-φ5
3.2.2. Main board: (mm)
+
+
+
+
240
161
160
121
12061
60
1
SLOT‑4 SLOT‑3 SLOT‑2 SLOT‑1
MADEIN JAPAN
PHOTRONLtd.
PCITMEM‑991005
PCITPOW‑991005
+
+
311 .88
106 .55
- 29 -
FASTCAM-PCI Series Hardware Manual
3.3. Care of Lenses
The surface of photographic lenses have thin coatings that reduce chromatic aberration, unwanted
reflections, and other distortions. Extra care should be taken to protect this fragile coating.
Protect the lens by installing a lens cap when you are not using the camera. Brush the lens
gently with a camel hair brush or loosely folded piece of lens paper to remove dust particles. For
stubborn dirt use photographic lens cleaning solution and lens wipes. Never rub the lens with
direct pressure or drop cleaning solution directly on the lens surface.
- 30 -
FASTCAM-PCI Series Hardware Manual
www.photron.com
In Americas
PHOTRON USA,INC.
9520 Padgett Street, Suite 110
San Diego,CA 92126-4446,USA
Phone: 858-684-3555
Fax: 858-684-3558
E-mail:image@photron.com
In Europe:
PHOTRON EUROPE LIMITED
Willowbank House
84 Station Road
Marlow, Bucks SL7, U.K
Phone:+44(0) 1628 89 4353
Fax: +44(0) 1628 89 4354
E-mail:image@photron.com
In other areas:
PHOTRON LIMITED
Shibuya 1-9-8,Shibuya-ku
Tokyo 150-0002,Japan
Phone:+81 3 3486 3471
Fax: +81 3 3486 8760
E-mail:image@photron.com
FASTCAM Control Software Operation Manual
English edition
Aug. 2001
Rev.2.2
- 31 -
Loading...