Phoenix Gold SD1300.1, SD1300.5 User Manual

Amplifier Manual

Manuel de l’amplificateur

Features: Caractéristiques:

• High Eciency Class D Topology

• Compact Size for Easy Installation

• High and Low Pass Crossovers

• Robust Unregulated Power Supply

• Surface Mount Component Technology

• Panel Mounted RCAs

• Direct Insert Power and Speaker Terminals

• Audio Precision Quality Control Verication

• High Temperature Plexiglass cover

• Remote subwoofer level control included

• Topologie de classe D de gamme complète

• Petit format pour faciliter l’installation

• Filtres croisés passe-haut et passe-bas

• Alimentation électrique robuste non réglementée

• Technologie de composant monté en surface

• Amplicateurs à couplage RC montés sur des panneaux

• Terminaux d’alimentation et de haut-parleurs à insertion directe

• Vérication du contrôle de la qualité de la précision audio

• Couvercle de plexiglas résistant aux températures élevées

• Niveau de contrôle de passe-bas inclus

Model: SD1300.1, SD1300.5

Specifications

SD1300.1 SPECIFICATIONS

Frequency Response: ± 1dB from 20Hz to 300Hz Signal to Noise Ratio: >90dB Low Pass Crossover: 18dB per Octave Subsonic Filter: 12dB per Octave Low Pass Crossover Range: 30Hz to 300Hz Subsonic Crossover Range: 10Hz to 55Hz Bass Boost @ 45Hz: 0 to +18dB Low Level Input Range: 200 millivolts to 8 volts Lowest Recommend Load: 1 ohm Typical Eciency: 70% Damping Factor: Greater than 200

Amplier Owner’s Manual

RMS Power 14.4Vdc ≤ 1% THD 900 x 1 @ 2 ohms 1300 x 1 @ 1 ohm

Dynamic Power 14.4Vdc >1% THD 1200 x 1 @ 2 ohms 1600 x 1 @ 1 ohm

Recommended Fuse Size: 120 amp Power/Ground Wire Size: 4 Gauge Dimensions (Includes Mounting Feet): 14.33” L x 6.93” W x 2.0” H 364mm L x 176mm W x 51mm H Dimensions (Includes Terminals): 14.96” L x 6.93” W x 2.0” H 380mm L x 176mm W x 51mm H

SD1300.5 SPECIFICATIONS

Frequency Response: ± 1dB from 20Hz to 20kHz Signal to Noise Ratio: >100dB High Pass Crossovers: 12dB per Octave Low Pass Crossover: 18dB per Octave High Pass Crossover Range: 15Hz to 250Hz Low Pass Crossover Range: 30Hz to 300Hz Bass Boost @ 45Hz: 0 to +18dB Low Level Input Range: 200 millivolts to 8 volts Front and Rear Channels Lowest Load: 4 ohms Bridged or 2 ohms Stereo Subwoofer Channel Lowest Load: 2 ohm Typical Eciency: 70% Damping Factor Greater than 200

Note: All SD ampliers operate correctly up to 14.4 volts. Do not operate the amplier above 14.4 volts. The amplier will engage its overvoltage protection, the result is no audio output on one or more channels.

RMS Power 14.4Vdc ≤1% THD 80 x 4 @ 4 ohms Stereo 125 x 4 @ 2 ohms Stereo 250 x 2 @ 4 ohms Bridged plus 500 x 1 @ 4 ohms 800 x 1 @ 2 ohms

Dynamic Power 14.4Vdc >1% THD 95 x 4 @ 4 ohms Stereo 150 x 4 @ 2 ohms Stereo 300 x 2 @ 4 ohms Bridged plus 700 x 1 @ 4 ohms 1000 x 1 @ 2 ohms

Recommended Fuse Size: 100 amp Power/Ground Wire Size: 4 Gauge Dimensions (Includes Mounting Feet): 14.33” L x 6.93” W x 2.0” H 364mm L x 176mm W x 51mm H Dimensions (Includes Terminals): 14.96” L x 6.93” W x 2.0” H 380mm L x 176mm W x 51mm H

Amplier Owner’s Manual

GROUND REM OTE + 12V

GROU ND + 12VR

FUSE

40A40A

40A

POWER

SENS

MIN MAX

BASS

0dB 18dB

X-OVER

FREQ.

30Hz 300Hz

REMOTE

PROTEC T

SUBSONIC

10Hz 55Hz

INPUT

RMD

SPEAKER

SD1300.1

Monoblo ck Power Amplifier

INPUT

Connect preamp signal cables from the head unit to these terminals.

CROSSOVER FREQUENCY

Controls the lowpass crossover point for the speaker outputs.

BASS BOOST

Variable bass boost from 0 to +18dB @ 45Hz.

REMOTE LEVEL CONTROL

This port is for connecting the subwoofer remote level control. This allows up to 20dB of volume adjustment. This is not a bass boost, it controls the level of the low pass signal.

NOTE: This control is not compatible with the Phoenix Gold LPL44 level

control.

SENS

Used to reach maximum amplier power with a wide variety of headunits.

SUBSONIC CROSSOVER FREQUENCY

Controls the highpass crossover point for the speaker outputs to eliminate extreme low frequencies.

RMD

Optional RMD Voltage Display plugs into this port. Sold separately.

+12V

This must be connected to the fused positive terminal (+12V) of the car’s battery. The fuse must be located within 18 inches of the battery.

REMOTE

This must be connected to switched +12V, usually a trigger wire coming from the head unit or ignition.

GROUND

This must be connected to the negative terminal of the car’s battery or bolted to a clean, unpainted part of the chassis of the vehicle.

NOTE: Visible through the plexiglass cover, a single blue power LED is located in the lower corner of all SD ampliers.

SPEAKER OUTPUTS

Used to connect the amplier to speakers. SD1300.1 minimum impedance is 1 ohm.

SD1300.5

GROUND REM OTE + 12V

GROU ND + 12VR

FUSE

40A40A

40A

POWER

SENS

MIN MAX

BASS

0dB 18dB

X-OVER

FREQ.

30Hz 300Hz

REMOTE

PROTEC T

SUBSONIC

10Hz 55Hz

INPUT

RMD

SPEAKER

PROTEC T

POWER

REMOTE

SUB INPUT

MIN MAX

SENS

SENS BASS BOOST

0dB 18dB

HPF

15Hz 250Hz

HPF

15Hz 250Hz MIN MAX

SENS

30Hz

LPF

300Hz

GROUND REM OTE + 12V

SUB.

INPUT

SUB INPUT

SU B FRONT

FRONT REAR

RL RR

GROU ND + 12VR

RMD

5 Channel Power Amplifier

Amplier Owner’s Manual

FRONT, REAR AND SUB INPUTS

Connect preamp signal cables from headunit to these inputs. The front AND rear inputs must be used, if only the front input is used then the rear speaker outputs will have no output signal. The Sub Input may or may not be used see SUB INPUT SWITCH for more information.

HPF AND LPF CROSSOVER FREQUENCY

Controls the crossover point for the speaker outputs.

REMOTE LEVEL CONTROL

This port is for connecting the subwoofer remote level control. This allows up to 20dB of volume adjustment. This is not a bass boost, it controls the level of the subwoofer channel only.

NOTE: This control is not compatible with the Phoenix Gold LPL44 level

control.

BASS BOOST

Variable bass boost from 0 to +18dB @ 45Hz for the subwoofer channel only.

SENS

Used to reach maximum amplier power with a wide variety of headunits.

SUB INPUT SWITCH

IN: Subwoofer speaker output is fed by the sub Input. If the headunit or processor has a subwoofer low level output use this setting. OUT: Subwoofer speaker output is fed by the front input and the sub Input is not used. If the headunit or processor only has front and rear low level outputs use this setting.

RMD

Optional RMD Voltage Display plugs into this port. Sold separately.

+12V

This must be connected to the fused positive terminal (+12V) of the car’s battery. The fuse must be located within 18 inches of the battery.

REMOTE

This must be connected to switched +12V, usually a trigger wire coming from the head unit or ignition.

GROUND

This must be connected to the negative terminal of the car’s battery or bolted to a clean, unpainted part of the chassis of the vehicle.

NOTE: Visible through the plexiglass cover, a single blue power LED is located in the lower corner of all SD ampliers.

SPEAKER OUTPUTS

Used to connect the amplier to speakers. Front and Rear Channel minimum impedance is 4 ohms bridged or 2 ohms stereo. Subwoofer channel minimum impedance is 2 ohms. Use Right + and Left - to bridge the front or rear channels, the subwoofer channel is not bridgeable.

+ 8 hidden pages