Phoenix Gold pm950, pm700 User Manual

p m 70 0 / p m 9 50

Professional Stereo Power Amplifier

Introduction

Congratulations on your purchase of a new Carver Professional Power Amplifier. It is backed by state-of-the-art engineering and manufacturing techniques to bring you the best in quality craftsmanship and reliable performance. The pm700 and pm950 are specially designed for pro sound applications. Their rugged construction and low profile make them ideal for sustaining the abuses of the road with reliability and space-saving economy. And their accurate sound and ample power make them ideal for critical studio applications as well. The pm700 is rated at 350 watts per channel into 4 ohms and 225 watts per channel into 8 ohms. In bridged mono operation it is rated at 700 watts into 8 ohms. The pm950 is rated at 475 watts per channel into 4 ohms and 325 watts per channel into 8 ohms. In bridged mono operation it is rated at 950 watts into 8 ohms. The sophisticated protection circuits designed into these amplifiers will protect your system should an unexpected fault occur.They also protect the amplifiers from excessive temperature, continuous current limiting and shorted outputs. The balanced input uses a high quality, high common-mode rejection differential amplifier for exceptional hum and noise rejection. The sequencing feature allows a rack of amplifiers to be powered up from a remote location. The daisy-chain connection scheme causes each amplifier to turn on in sequence, preventing the l a rge in-rush current that can occur when an entire rack of amplifiers is turned on s i m u l t a n e o u s l y. These power amplifiers were designed and manufactured by people with a lifetime commitment to providing the world’s finest components for music and sound reproduction. Thanks for placing your confidence in Carver Professional. We know your amplifier will provide many years of dependable s e r v i c e and reliable sound reproduction.

Unpacking and Paperwork

Carefully unpack the amplifier and keep the original carton and packing materials for future moving, shipment or long-term storage. After opening the box, please check for any visible signs of damage that were not apparent from the outside of the box. If you do encounter what appears to be concealed damage, please consult your Carver Professional Dealer before installing the unit.

Important Paperwork

Make sure to save your sales receipt. Your receipt is extremely important to establish the duration of your Limited

pm700

225W per channel into 8 ohms

•

350W per channel into 4 ohms 700W mono into 8 ohms XLR and 1/4” TRS input connectors

•

Accepts balanced or unbalanced lines

•

• Multi-way Binding Post output connectors

Independent 11 detent level controls for

•

CH1 and CH2 External Level Control Defeat Switch

•

Dual Mono mode for operating both channels

•

with a single mono input Bridged Mono mode for combining the power of

•

both channels into a single higher powered channel Input sensitivity set at 1.5V RMS from factory.

•

Internally configurable to 0.775V RMS Internally configurable input polarity

•

Internal connection points for add-on accessories

•

Power ON Sequencer

•

Class H dual-rail power supply

•

Independent CH1/CH2 Speaker relays will

•

instantaneously disconnect if one of the following fault conditions is detected:

D.C. Offset Over Temperature Short Circuit

Additional protection circuitry includes:

•

Clipping Eliminator AC Line Fuse

Power Connected/Standby indicator

•

7 LED display per channel, including Power

•

Ready and Clip/Protect indicators 2-speed Fan cooled

•

70-volt/100-volt transformer option

•

CE 1997 approved

•

Power Output:: (20Hz to 20kHz, with no

BACK

more than 0.1% THD)

225 watts per channel into 8 ohms 350 watts per channel into 4 ohms

Bridged-mono:

700 watts into 8 ohms at 1kHz, with no more than 0.1% THD

Dynamic Headroom: >2.0dB F requency Response:

20Hz to 20kHz (±0.75 dB)

Channel Separation:

>65dB @ 1kHz

Damping Factor: <400 Input Impedance: 25 Kohms unbalanced

50 Kohms balanced

Sensitivity: Low: 1.5 VRMS for

rated power into 4 ohms 160mVRMS for 1W into 4 ohms High: 0.775VRMS forrated power into 4 ohms 83mVRMS for 1W into 4 ohms;

Gain: High: 33.8dB (±0.5dB)

Low: 27.8dB (±0.5dB)

Input Overload: +18dB THD: <0.1% IM Distortion: <0.1% Signal-to-Noise Ratio:

>100 dB, A-weighted, ref. to rated power into

4 ohms

Slew Rate: 40V/µS

(Bandwidth limited)

CMRR: >80dB @ 1kHz Power Consumption:

55W at idle; 500W with musical program; 1000W at full power into 8 ohms (continuous); 1550W at full power into 4 ohms (continuous)

Power Requirements:

120VAC/60Hz (USA and Canada) Other voltages as required for export

Fusing: 10 amp slo-blo

(120V/60Hz)7amp slo-blo (230V/50Hz)

Sequence Receive Terminal:

+7V to +15V DC 50mA min. current requirement

Display: 7 LED indicators per

channel 1 green READY, 5 yellow SIGNAL, 1 red CLIP / PROTECT

Size (H x W x D): 3.50” (2U) x 19” x

13.25” 89mm x 483mm x 337mm

Net Weight: 30 lbs. (13.6 kgs) Shipping Weight: 36 lbs. (16.3 kgs)

Due to on-going product development, features, specifications, and availability are subject to change without notice.

pm950

325W per channel into 8 ohms

•

475W per channel into 4 ohms 950W mono into 8 ohms XLR and 1/4” TRS input connectors

•