Phoenix Gold AMP One-A User Manual

Stereo Power Amplifier with Internal Bridging

AMP One/A

Congratulations on your new purchase and welcome to the AudioSource family of satisfied customers.
We trust you will continue to enjoy the value and quality of your AudioSource AMP One/A for many years
to come. To ensure the best performance from your unit, please take a few moments to read this manual.
Also, be sure to retain this document for future reference.

Note: If any part of this product is damaged or missing, do not contact your AudioSource dealer. Please call us directly at 800-435-7115.

Owner’s Manual

© 1999 AudioSource, Inc.

Front Panel Controls

Power

This front panel button switches the AMP One/A on or off. A multicolored LED indicates its power status.

Note: This amp uses a two-stage soft startup. The amp will power up in standby mode. When its power supply stabilizes, after
a few seconds, it will become fully operative.

Input Level Controls

These knobs adjust the incoming signal level and thereby act as volume controls. We recommend that you
leave these on max and use your signal source (receiver, CD player, preamplifier, etc.) to adjust the volume.

Hooking up the Wires

Audio signals travel out of one component and into another. All of your connections should also go from out to in.

Line In

Connect the line out jacks from your signal source (receiver, CD player, preamplifier, etc.) to the line in
jacks on the AMP One/A.

Line Out/Thru

If you are using multiple amplifiers in your system, the AMP One/A features a stereo pair of Line Out/Thru
jacks to send the original signal directly to these additional amplifiers.

Bridging Switch (refer to wiring diagram)

In addition to providing 80 watts RMS per channel in the stereo mode, your AMP One/A can be used as a
high power mono amplifier, providing over 200 watts RMS. This can be accomplished by sliding the bridging
switch from the stereo position to the mono position. For mono applications, use only the right channel input.
Similarly, use only the right channel input level control.

Note: Be sure to observe the correct speaker connections for bridged applications. Because of the high power output in this
mode, we recommend initially setting the right level control at "min", and then adjusting the volume to the desired level.

Speaker Terminals

One pair of speakers can be used with the AMP One/A. This amp uses five-way binding post speaker
outputs. The speaker terminals are color coded. Red posts indicate positive (+) terminals and black posts
indicate negative (–) terminals. Be sure to connect the positive output terminals of your AMP One/A to
the positive input terminals of your speakers and the negative output terminals of your AMP One/A to the
negative input terminals of your speakers.

Note: On some units, the labeling of the left and right speaker terminals has been reversed. Refer to the wiring diagrams on the
next page for proper connection of speaker cables.

432

1

F

U

S

E

FUSE 4A

LINE

OUT/THRU

LINE

IN

BRIDGING

STEREO (OFF)MONO (ON)

STEREO

(RIGHT) (LEFT)

RIGHT

LEFT

MODEL AMP ONE/A

-

+

-

+

BRIDGED

+

-

1

2

4

3

Amplifier Power Output . . . . . . . . .80 watts per channel

200 watts monobridged

Total Harmonic Distortion . . . . . . . . . . . . . . . . . .<0.04%

Intermodulation Distortion . . . . . . . . . . . . . . . . . <0.04%

Frequency Response . . . . . . . . .20Hz to 20kHz, ±0.5 dB

Signal to Noise Ratio . . . . . . . . . . . . . . . . . . . . . .110 dB

Input Sensitivity . . . . . . . . . . . . . . . . . . . . . .0.8 V (line)

Input Impedance . . . . . . . . . . . . . . . . . . . . .30K Ω (line)

Headroom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2dB

Functions . . . . . . . . . . . . . . . Mono Bridging (rear panel)

Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . .Line In (RCA)

Outputs . . . . .Line Out/Thru (RCA), Speaker (left, right)

Dimensions . . . . . . . . . . . . .161⁄2"W x 23⁄8"H x 115⁄8"D

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14lbs., 5oz.

AMP One/A Specifications

Design and specifications are subject to change without notice.

Enjoy your new purchase.This manual provides detailed diagrams and instructions for setting up your

equipment. Our commitment to your satisfaction doesn't end there.We also offer friendly,toll-free assistance.

1-800-HELP-115

Stereo Setup

In this configuration,

the bridging switch is off
for stereo operation.
Connect the line out
jacks from a stereo pre­amplifier to the line in jacks of
your AMP One/A. Next, connect
your speakers to the five-way
binding post speaker terminals
(observing proper polarity:
red for "+", and black for "-").

Mono Setup

In this configuration,

the bridging switch is on.
Connect the line out
from a preamplifier to
the line in right of your AMP
One/A. Connect your mono
speaker to the terminals of your
AMP One/A, following the example
in the diagram opposite. Use the
right level control on the front panel
to adjust the volume.

F

U

S

E

FUSE 4A

LINE

OUT/THRU

LINE

IN

BRIDGING

STEREO (OFF)MONO (ON)

STEREO

(RIGHT) (LEFT)

RIGHT

LEFT

-

+

Right Speaker

MODEL AMP ONE/A

-

+

-+-

+

Left Speaker

BRIDGED

+

-

F

U

S

E

FUSE 4A

LINE

OUT/THRU

LINE

IN

BRIDGING

STEREO (OFF)MONO (ON)

STEREO

(RIGHT) (LEFT)

RIGHT

LEFT

MODEL AMP ONE/A

-

+

-+-

+

Mono Speaker

BRIDGED

+

-

Read Instructions

All the safety and operating instructions should be read before
the appliance is operated.

Retain Instructions

The safety and operating instructions should be adhered to.

Heed Warnings

All warnings on the appliance and in the operating instructions
should be adhered to.

Follow Instructions

All operating and use instructions should be followed.

Water and Moisture

The appliance should not be used near water. For example, near a
bathtub, washbowl, kitchen sink, laundry tub, in a wet basement,
or near a swimming pool, etc.

Ventilation

The appliance should be situated so that its location or position
does not interfere with its proper ventilation. For example, the
appliance should not be situated on a bed, sofa, rug, or similar
surface that may block the ventilation openings; or, placed in a
built-in situation, such as a bookcase or cabinet that may impede
the flow of air through the ventilation openings.

Heat

The appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.

Power Sources

The appliance should be connected to a power supply only of
the type described in the operating instructions or as marked on
the appliance.

Grounding or Polarization

Precautions should be taken so that the grounding or polariza­tion means of an appliance is not defeated.

Power Cord Protection

Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed on or against them,
paying particular attention to cords at plugs, convenience recep­tacles, and the point where they exit from the appliance.

Cleaning

The appliance should be cleaned only as recommended by the
manufacturer.

Power Lines

An outdoor antenna should be located away from power lines.

Non-Use Periods

The power cord of the appliance should be unplugged from the
outlet when left unused for a long period of time.

Object and Liquid Entry

Care should be taken so that objects do not fall and liquids are
not spilled into the enclosure through openings.

Damage Requiring Service

The appliance should be serviced by qualified service personnel
when: a) The power supply cord or the plug has been damaged;
b) Objects have fallen, or liquid has been spilled into the appli­ance; c) The appliance has been exposed to rain; d) The appli­ance does not appear to operate normally or exhibits a marked
change in performance; or e) The appliance has been dropped,
or the enclosure damaged.

Servicing

The user should not attempt to service the appliance beyond that
described in the operating instructions. All other servicing
should be referred to qualified service personnel.

Product Servicing

In the event that your AMP One/A fails to operated properly,
please contact the dealer where you purchased the unit. Or you
may contact AudioSource directly for further assistance.

Safety Instructions

Warning: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
Caution: To reduce the risk of electric shock, do not remove cover (or back); no user serviceable parts inside. Refer servicing to

qualified service personnel.

Caution: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Attention: Pour eviter les chocs electriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et

pousser jusqu'au fond.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous
voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons. The exclamation point
within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

9300 North Decatur
Portland. OR, 97203
Tel. [phone]
Fax [phone]
[e-mail]
www.audiosource.net Printed in Taiwan