Phoenix R200 LGR, R200 Owner's Manual

4201 Lien Rd. • Madison, WI 53704

Owner’s Manual — Phoenix R200 LGR Dehumidifier

Installation, Operation & Service Instructions

Read and Save These Instructions

The Phoenix R200 is a compact, energy efficient LGR
dehumidifier that removes 125 pints per day (AHAM) while
drawing only 8.3 amps of electricity. The R200 outperforms
larger competitive dehumidifiers by removing more water,
providing larger grain depression and consuming less power.
The proven LGR design is surrounded by a durable roto­molded high impact plastic to create a dehumidifier that is
smaller and lighter than competitive units.

The Phoenix R200 LGR Dehumidifier

Patented Bypass Technology - Increased performance over a
wide temperature range.

R-410A Refrigerant - The Phoenix R200 comes charged
with R-410A refrigerant.

Capacity - The Phoenix R200 removes 125 pints per day at
AHAM (80°F/60%RH).

Energy Efficiency - Draws only 8.3 amps and removes 5.2
pints/kWh.

Compact Design - Smaller, 20”x20”x33.5”, and only 105 lbs.

Motorized Impeller - 325 CFM; Faster drying and superior

static pressure for ducting.

More Grain Depression - Drier air from an LGR finishes jobs
quicker versus a conventional refrigerant dehumidifier.

Focused Airflow - Patent focused outlet directs air downward
across the wet surface.

Multiple Ducting Options - 12” intake, 10” exhaust.

Plastic Housing - Rugged roto-molded housing.

Solid State Controls - Easy to read and operate.

Protected Condensate Hose - Located under the top cover.
Quick connect, cannot catch or be damaged on obstructions.

Telescoping Handle - A heavy-duty retractable handle for ease

of transport and reduces space for storage and stacking.

Recessed 12” Wheels - Allows greater maneuverability on the
job site and efficient storage. Rolls over obstacles with ease.

Pleated Media Air Filter - A 12”x12”x1” MERV-11 filter is
standard.

Stacking/Nesting - Reduces space for ease of stacking and
storage.

Specifications subject to change without notice.

In addition to the performance benefits and compact size,
the R200 has patented bypass technology, increased
airflow, multiple ducting options, and a pleated media
filter. The R200 is the latest member of the Phoenix line of
LGR dehumidifiers; the most effective and versatile drying
devices made.

Patented

BYPASS

Phoenix R200

Part No. 4027000
Patent 7,246,503

7,281,389
7,540,166

1

www.UsePhoenix.com • [e-mail]-Free 1-800-533-7533

TS-391

09/13

Table of Contents

Introduction ...............................................................1

1. Safety Certifications ..............................................2

2. Specifications .......................................................2

3. Operation ............................................................2

3.1 Transporting ...................................................2

3.2 Electrical Requirements ..................................2

3.3 Condensate Removal ......................................3

3.4 Ducting ..........................................................3

3.5 Defrost Cycle .................................................3

3.6 Power Button .................................................3

3.7 Purge Button ..................................................3

3.8 Hour Meter ....................................................3

3.9 Hours Button .................................................3

3.10 Defrost Light ................................................4

3.11 Bypass Control .............................................4

4. Maintenance ........................................................4

4.1 Air Filter .........................................................4

4.2 Storage .........................................................4

5. Service ................................................................4

5.1 Technical Description ......................................4

5.2 Troubleshooting ..............................................5

5.3 Air Mover .......................................................6

5.4 Thermistor .....................................................6

5.5 Condensate Pump ..........................................6

5.6 Float Safety Switch .........................................6

6. Options & Accessories ..........................................7

7. Wiring Diagram ....................................................7

8. Service Parts .......................................................8

9. Warranty ..............................................................9

1 Safety Certifications

The Phoenix R200 conforms to standards ANSI/UL 474

and CSA C22.2 No.92.

2 Specifications

Part No. 4027000

Power 8.3 amps, 120 VAC, Grounded

Water 125 pints/day @ AHAM (80°F, 60%)
Removal 26 gal/day maximum @ saturation

Blower 325 CFM without external ducting

300 CFM @ .15 IWG external static

Refrigerant 1 lb, 10 oz. R-410A
Charge

Operating 33°F to 110°F
Range

Filters: 12” x 12” x 1” Pleated Media MERV-11

Duct Intake – 12” Flex-Duct
Options Outlet – 10” Lay-Flat

Warranty Five years;

1st year 100% of Parts and Labor
2nd-5th year 100% of sealed refrigeration
system parts.

Dimensions

Unit Shipping
Width 20” 21”
Height 33.5” 35.25”
Depth 20” 21”
Weight 105 lbs 115 lbs

Patent - 7,246,503
7,281,389
7,540,166

Read the operation and maintenance instructions
carefully before using this unit. Proper adherence to
these instructions is essential to obtain maximum
benefit from your Phoenix R200 dehumidifier.

• It is designed to be used INDOORS ONLY.

• If used in a wet area, plug it into a GROUND FAULT

INTERRUPTER.

• DO NOT use the Phoenix R200 as a bench or table.

• It must always be used in the upright position.

3 Operation

Place dehumidifier inside structure,
place condensate hose into a drain, or
a large water tight container, and turn
on. To decrease drying times, make sure
all windows and doors are closed to the
outside and seal off the affected wet
areas from unaffected areas.

Optimum performance will be observed

between the temperatures of 70°F and

95°F.

3.1 Transporting

The Phoenix R200 features a high impact roto-molded
housing with 12” recessed wheels and a telescoping
handle. The rugged roto-molded housing protects the
dehumidifier from damage. The 12” wheels provide
greater maneuverability and roll over obstacles with ease.
The telescoping handle and recessed wheels create a

2

www.UsePhoenix.com • [e-mail]-Free 1-800-533-7533

Figure 1: Stacked
Phoenix R200

compact dehumidifier for improved storage and transport.
To operate the telescoping handle, pull out the lever to
release the lock and lift the handle until it locks in the up
position. Repeat to lock the handle in the down position.
More compact storage can be achieved by stacking
the units two high. The wheels of the unit ‘nest’ in the
indentations of the bottom unit to provide stability, see
figure 1. It is recommended the units are properly secured
for transport. The Phoenix R200 must always be upright
when transported by vehicle. It may be tipped onto its
handle and back for loading and moving by hand.

Figure 2: Phoenix R200 control board.

3.2 Electrical Requirements

The Phoenix R200 plugs into a common grounded outlet
on a 15 amp circuit. It draws 8.3 amps at 80°F, 60% RH.
If used in a wet area, a ground fault interrupter (GFI) is
required. If an extension cord is required, it must have a
minimum of 14 gauge conductors if 25 feet long or less
and 12 gauge conductors if greater than 25 feet long.

3.3 Condensate Removal

The Phoenix R200 is equipped with an internal condensate
pump to remove the water that is condensed during
dehumidification. This pump allows the condensate to be
pumped 20 feet above the unit with the attached hose. If
the condensate must be pumped more than 20 feet above
the unit, a relay pump must be added. The condensate
pump automatically purges for 20 seconds every eight
minutes. Use the PURGE button to empty reservoir. If the
condensate level rises in the reservoir to a critical level a
back-up float switch will activate the pump-out for up to 1
minute. If the water in the reservoir fails to be evacuated,
the safety switch will turn off the compressor.

3.4 Ducting

A wire duct collar is supplied to allow 10” lay-flat duct to
be attached to the Phoenix R200 outlet. Lay-flat plastic
ducting is available (see accessories in section 6). Attach
ducting to the wire duct collar by inserting the plastic duct
end through the collar center and rolling the duct end
outward to overlap the outside of the collar. The duct and
collar may then be quickly attached to the Phoenix R200
by snapping the collar over the four plastic exhaust tabs.

If the R200 is located in the unaffected area, the intake
can be ducted with 12” flex duct (see accessories in
section 6). Attach the flex duct to the top cover by hooking
the spiral wire under the four tabs. Tape the duct to the
top cover for a complete seal.

3.5 Defrost Cycle

If the low side refrigerant temperature drops below the
defrost set point, due to excessive frost formation on the
evaporator coil, the thermistor activates the solid-state
control and the defrost light. The control cycles the com­pressor “off” and “on” by the thermistor temperature mea­surement. The air mover will continue to run, causing air
to flow through the evaporator coil and melt the ice when

the compressor is off. When the air temperature and/or
humidity increases, the evaporator temperature will rise
and the thermistor will end the defrost cycle at the defrost
set point.

3.6 POWER Button

Press the POWER button to turn the dehumidifier “on” or
“off”. When starting the dehumidifier the display will show
the accumulated hours. Press the POWER button again to
turn the dehumidifier off. The display will also power off.

3.7 PURGE Button

During normal operation the pump automatically cycles
every four minutes. Press the PURGE button to remove
condensate manually from the reservoir. There are three

ways to manually remove water from the reservoir:

1. Press the PURGE button once and the pump will run
for 20 seconds

2. Press and hold the PURGE button and the pump will
run for up to 30 seconds

3. Press the PURGE button while the dehumidifier is
plugged in but powered off and the pump will run for
30 seconds.

Always manually purge the water reservoir before transport
or storage. Turn off the power and allow the plugged in
dehumidifier to rest 15 minutes before the final purge.

3.8 Hour Meter

The digital hour meter displays the amount of time the
dehumidifier has been turned on to the tenth of an hour.
The hour meter continuously cycles between total machine
hours and job hours every 3 seconds. Hours are stored
in memory even when the unit is unplugged. The previous
totals will be displayed next time the unit is powered on.

3.9 HOURS Button

Pressing the HOURS button displays the hour meter when
the unit is turned off but plugged into power. To reset job
hours, press and hold the HOURS button for 5 seconds
when the unit is operating.

3

www.UsePhoenix.com • [e-mail]-Free 1-800-533-7533