Phoenix MRS 64/1000 Series, MRS 64/1000S Series Installation Instructions & Repair Parts List
MRS 64/1000 & 64/1000S Series
Installation Instructions & Repair Parts List
CAUTION
!
• All wiring should be done by a licensed electrician in accordance with state codes, local codes and National Electric Code (NEC) standards.
• Improper installation may result in serious injury and void warranty.
• When fixture is installed in a Class I, Division 2 Hazardous Location, strict compliance to the fixture warning label instructions must be met.
• Wiring connections must be made with metal conduit or flexible cord in compliance with Class I, Division 2 wiring methods defined in the National Electric
Code.
• Use protective gloves and eye equipment when replacing lamps.
Wiring
The fixtures are pre-wired with a five (5) foot three (3) conductor electrical cord “pigtail” for wiring to suitable power source. The green conductor is grounded to
the fixture and must be connected to a positive ground. Do not connect green wire to power source.
Mounting
Fasten fixture with four (4) ⅜ inch bolts through holes provided in mounting base. Do not mount on unsupported cab or house roof. Attach near corner supports
or use adequate sub-base. Avoid mounting on light-weight cross members of booms or derricks which will vibrate or flex excessively. In addition to normal (base
down) mounting fixture may be attached in a pendant or cantilever manner.
Lamping
The MRS 64/1000 Series fixtures are designed to use incandescent and quartz tube halogen cycle par 64 lamps. Lamping is accomplished through the hinged
cover glass assembly. Loosen three (3) wing nuts on lamp support ring and rotate lamp retaining ring free from wing nuts to release lamp from supporting ring. To
replace a lamp the procedure must be reversed and the three (3) wing nuts snugly finger tightened.
When relamping, it is recommended that the cover glass be cleaned to maintain fixture efficiency (see cleaning).
Lamp Type Designations
Quartz Tube Halogen Cycle Lamp or ANSI Number Incandescent Lamp or ANSI Number
Q1000 Par 64/MFL 500 Par 64/MFL
Q1000 Par 64/WFL 500 Par 64/WFL
Q1000 Par 64/NSP 500 Par 64/NSP
Q1000 Par 64/VNSP
Aiming
Aiming adjustments are made by loosening the single bolt (or handle on “S” model) that attaches the harp to the mounting base and the two (2) bolts (or handle
on the “S” model) holding the fixture to the harp. The fixture can then be positioned to the desired aiming point. The fixture may be rotated 180 degrees about
each of the two adjustable axes for proper aiming. It may be necessary, in some installations, to rotate the fixture for easier access for relamping. The same
procedure as for aiming should be employed.
Phone: +1 414.973.3300 Toll Free: 800.438.1214 Fax: +1 414.973.3210 www.phoenixlighting.com
Phoenix Products Company Inc. 8711 West Port Avenue Milwaukee, WI 53224 USA
MRS 64/1000 & 64/1000S Series
Installation Instructions & Repair Parts List
Repair Parts List
Item Qty Description MRS 64/1000 (Part No.) MRS 64/1000S (Part No.)
floodlight assembly complete 1010400 1010700
1 1 lamp/socket support assembly 1621900 1621900
2 1 base assembly 1817100 1821300
3 4 bolt-nut assembly, ¼ - 20 1817400 1817400
4 1 handle assembly - 1821100
5 1 handle assembly - 1821200
6 1 diaphragm ring, 9 -⅓ O.D. contact factory contact factory
7 1 harp 2400900 contact factory
8 1 door frame 2634600 2634600
9 1 heat sheild 2634710 2634710
10 4 cover glass retaining clip 2751750 2751750
11 1 s.s. bushing, ¾ O.D. - 2649400
12 1 s.s. bushing, ½ O.D. - 2649600
13 1 handle bracket - 2649700
14 1 snap bushing 4024200 4024200
15 1 cord grip, ½ inch 4032000 4032000
17 1 cord assembly, 5 foot 4116800 4116800
18 1 mogul-end-prong lamp socket 4502200 4502200
19 1
20 1 cover glass gasket 5002202 5002202
21 4 s.s. round head machine screw, 10-24 x ⅜ 6009500 6009500
22 12 Phillips pan head type F machine screw, 6-32 x ½ 6001600 6001600
23 2 s.s. Phillips flat head machine screw, 10-24 x ⅝ - 6001800
24 1 Phillips pan type F machine screw, 6-32 x ⅜ 6002900 6002900
25 1 s.s. hex head cap screw, ⅝-11 x 1-¼ 6032300 -
26 2 s.s. hex head cap screw, ⅜ x 1-¼ 6032800 6032800
27 1 s.s. hex head cap screw, ½-13 x ¾ - 6033600
28 1 s.s. hex jam nut, ⅝-11 - 6201400
29 2 s.s. flat washer, ⅜ - 6300500
30 1 s.s. flat washer, ⅝ - 6300700
31 4 s.s. split lock washer, No. 8 6311000 6311000
32 1 s.s. split lock washer, ⅝ 6311700 -
33 2 s.s. split lock washer, ⅜ 6311800 6311800
34 1 s.s. split lock washer, ½ - 6311900
35 4 s.s. spring pin, ⁄ D. x ⅞ 6510300 6510300
36 2 s.s. spring pin, ¼ D. x 1 inch 6510400 6510400
37 1 plastic handle, 1-¼ D. x 4-½ (½ - 13 insert) - 7300200
flat cover glass (lens)
rounded cover glass (lens)
4610009
contact factory
contact factory
4610009
Phoenix Products Company Inc. 8711 West Port Avenue Milwaukee, WI 53224 USA
Phone: +1 414.973.3300 Toll Free: 800.438.1214 Fax: +1 414.973.3210 www.phoenixlighting.com
Loading...