Page 1
PHOENIX TALKING BODY FAT SCALE
MED-021-315-0004
Instruction Manual
Function:
Measures body weight and body fat percentage
with
voice
reading.
Technical specifications:
Weighing capacity: 200kg/400lb
Weighing graduation: 100g
Weighing deviation: ±1%
Optimum temperature range: 10°C - 40°C
Personal date memory: 10 sets
Page 2
Operation Instructions:
1. Inserting Batteries
Insert 4 AAA-size batteries into the battery compartment.
2. Personal Data Editing
In order to increase the accuracy of body fat percentage measurement,
personal data has to be set. Personal data including gender, height and
age can be stored in memory for up to 10 persons.
Stored data will remain in memory until being edited again.
a. Press the [POWER] key to turn on the unit. It will say "Hello". It will
say "I'm ready" when the display shows "0.0 lb"
b. Press SET key. Memory number "01" will appear in the display. Use
the [>] (ascending order) or [<] (descending order) key to select Memory
number. Press the SET key.
Use the [>] key to specify gender. Icon of selected gender will appear on
the left side of the display. Press the SET key.
c. When height value is displayed, use the [>] (ascending order) or [<]
(descending order) key to specify height. Height range: 3'3" to 7'3", with
increment of 1 inch. Press the SET key.
d. When age value (30) is displayed, use the [>] (ascending order) or [<]
(descending order) key to specify age. Age range: 10 – 100, with
increment of 1. Press the SET key.
e. The selected Memory number will appear in display again, indicating
that data input is complete.
To proceed to set personal data for other Memory numbers, press the [>]
or [<] key to select the next Memory number and repeat the above steps.
To start measurement using the selected Memory, press the SET key and
follow steps 'b' to 'd' in the following section.
To turn off the scale, simply press the [POWER] key.
Page 3
3. Taking Measurement
a. Press and Hold the [POWER] key to turn on the scale. It will say
"Hello". After 3 seconds, Memory number 01 to 10 will be displayed in
rotation at 1-second intervals. Release the [POWER] key when your
Memory number is displayed.
b. Your height and gender will be displayed. After about 2 seconds, the
display will show "0.0 lb" and it will say "I'm ready".
c. Step onto the measurement platform barefoot. Your weight will be
displayed and read out first. Then the display will show " " and
calculation will be performed automatically. Your body fat percentage and
evaluation result will be displayed and read out after the " " disappears.
Measurement is completed then.
d. Step off the platform. The values of body weight and fat percentage
will be displayed alternately 3 times. Then it will say "Goodbye" before
the power is automatically turned off.
4. Taking Weight Measurement Only
a. Press the [POWER] key to turn on the unit. It will say "Hello".
b. It will say "I'm ready" when the display shows "0.0 lb", step onto the
measurement platform. The body weight will be displayed and read out.
5. Select Measurement Unit
When the scale shows "0.0 lb", press the [Kg/Lb] key to switch between
the metric (kg and cm) and non-metric system (lb and in). Measuring
units of height and weight will be changed simultaneously.
6. Power Off
Press the [POWER] key to turn off the scale, or when no operation is
detected for about 10 seconds, it will say "Goodbye" and then shut down
automatically.
7. Switching ON/OFF the Talking Function
Use the switch on the bottom of the platform to switch on/off the speaker
function.
Important notes:
Page 4
When taking measurement, be sure you are barefoot, and that the
toes and heels are correctly aligned with the respective electrodes on
the measurement platform.
If a mistake takes place during measurement and causes the fat
percentage to fall out of the allowed range, "Err" will be displayed and
the unit will turn off automatically.
When over-loaded, "FFFF" will be displayed.
When the battery runs low, the warning icon will appear on the
display. When this happens, be sure to replace the battery
immediately.
Use the unit on hard, flat and secure surface only.
Place the unit in an area free from high temperature or high humidity.
To clean, use dampened cloth and mild detergent.
Avoid excessive impact or vibration to the unit.
If you do not intend to use this unit for a long period of time, remove
the battery before storage.
Do not attempt to disassemble the unit, otherwise the warranty will
become void.
The unit is intended for home and personal use only.
WARNING: DO NOT USE THIS PRODUCT IF YOU ARE USING ANY OF THE
FOLLOWING EQUIPMENT:
Cardiac Pacemaker
Electrocardiograph
Other medical devices implanted in the body or used for support.
For more information or to purchase a MyWeigh scale, please visit us at
www.myweigh.com
Loading...