Phoenix Hydro-X Xtreme Xtractor Owner's Manual

4201 Lien Rd Madison, WI 53704

Owner’s Manual — Hydro-X Xtreme Xtractor

Installation, Operation & Service Instructions

Read and Save These Instructions

The Phoenix Hydro-X Xtreme Xtractor is the most effective
and efficient extraction tool on the market today. The
Hydro-X’s patented Suction Roller provides both suction
and compression — forcing water to the surface then
sucking the water away, not allowing the water to be
reabsorbed back into the carpet and pad. No other
extractor today can pull as much water from the carpet and
pad as the Hydro-X Xtreme Xtractor.

The Hydro-X is steerable and self-propelled with variable
speeds. One restoration technician can operate the unit
and extract 1200 sq. ft. of carpet and pad in approximately
2 hours*!

The Phoenix Hydro-X Xtractor

Patents:
6,152,151
6,629,333

• Patented suction roller provides both suction and

compression forcing water to the surface.

• Self-propelled with positive chain drive –
no belts to break or adjust

• Variable speed for every carpet and pad condition

• Extracts in both forward and reverse

• Rust and corrosion resistant stainless steel

construction

• Built to withstand daily use

• Heavy-duty electronics

• One year warranty on parts and labor

*Time may vary depending on carpet style.

Specifications subject to change without notice.

Phoenix Hydro-X
Xtreme Xtractor

Part No. 4025600

1

TS-640

01/12

www.UsePhoenix.com • [e-mail]-Free 1-800-533-7533

Table of Contents

Introduction ...............................................................1

1. Specifications ........................................................2

2. Setup Instructions .................................................2

3. Operating Instructions ............................................3

3.1 Steering .........................................................3

3.2 Directional Control ...........................................3

3.3 Movement Control ...........................................3

3.4 Speed Control .................................................3

4. Basic Extraction Technique .....................................3

5. Other Information ..................................................3

5.1 Vacuum Units ..................................................3

5.2 Troubleshooting ...............................................3

6. Service Parts ........................................................4

Warranty ...............................................................5

Read the operation and maintenance instructions
carefully before using this unit. Proper adherence to these
instructions is essential to obtain maximum benefit from
your Phoenix Hydro-X Xtractor.

• It is designed to be used INDOORS ONLY.

• If used in a wet area, plug it into a GROUND FAULT

INTERRUPTER.

• It must always be used in the upright position.

1 Specifications

Part No. 4025600

Power 2.5 amps; 110-120 VAC grounded, 60 hz

Speed 0 - 28 Feet/Minute (Adjustable)

Either forward or reverse

Drive Motor 2.0 Amps

Fuse 5.0 Amp 250 VAC

Warranty One year; 100% Parts and Labor

Dimensions

Machine Shipping

Width 17” (Base) 27-1/2”

Height 52” 45-1/2”

Depth 20.5” (Base) 22”

Weight 70 lbs 80 lbs

2 Setup Instructions

To set up the Phoenix Hydro-X Xtreme Xtractor, unpack the
two boxes in which the unit was shipped.

1. Connect the handle assembly to the extraction
assembly by inserting the square tube attached to the
handle assembly into the square receiver and secure
with the supplied hitch pin.

2. Connect the black electrical leads together by inserting
the base assembly lead into the handle assembly lead
and tightening the collar. See figure 1a.

CAUTION: Key must be lined up correctly when plugging
handle into base assembly. Improper connection can result
in damage to connector pins, blown fuses or incorrect
product operation.

Figure 1a

Figure 1: Tube and receiver connections secured by hitch pins

2

www.UsePhoenix.com • [e-mail]-Free 1-800-533-7533