Page 1
TYPE SUP021YTDR
FOR HOUSEHOLD USE ONLY
Page 2
2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and/or injury to persons, including
the following:
1 Read all instructions and information in this instruction book and any other
literature included in this carton referring to this product before operating or using
this appliance.
2 Do not touch hot surfaces. Use handles or knobs.
3 To protect against fire, electric shock and personal injury do not immerse cord,
plugs or appliance in water or other liquid.
4 Close supervision is necessary when any appliance is used by or near children.
5 Unplug from outlet when not in use and before cleaning. Allow to cool before
putting on or taking off parts, and before cleaning the appliance.
6 Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions or has been damaged in any way. Return appliance to the nearest
authorized service centre for examination, repair or adjustment.
7 The use of accessory attachments not recommended by the appliance manufacturer
may result in fire, electric shock or personal injury.
8 Do not use outdoors.
9 Do not let cord hang over edge of table or counter, or touch hot surfaces.
10 Do not place on or near a hot gas or electric burner, or in a heated oven.
11 Always turn appliance “OFF”, then plug cord into the wall outlet. To disconnect,
turn switch to “OFF”, then remove plug from wall outlet.
12 Do not use appliance for other than intended household use.
13 Use extreme caution when using hot steam.
SAVE THESE INSTRUCTIONS
CAUTION
This appliance is for household use. Any servicing, other than cleaning and user
maintenance, should be performed by an authorized service centre. Do not immerse
base in water. To reduce the risk of fire or electric shock, do not disassemble the base.
There are no user serviceable parts inside. Repair should be done by authorized service
personnel only.
1 Check voltage to be sure that the voltage indicated on the nameplate corresponds
with your voltage.
2 Never use warm or hot water to fill the water tank. Use cold water only.
3 Keep your hands and the cord away from hot parts of the appliance during
operation.
4 Never clean with scouring powders or hard implements. Simply use a soft cloth
dampened with water.
5 For optimal taste of your coffee, use purified or bottled water. Periodic descaling is
still recommended every 2-3 months.
INSTRUCTIONS FOR THE POWER SUPPLY CORD
A A short power-supply cord is provided to reduce risks of getting tangled up or
tripping over a longer cord.
B Longer extension cords are available and may be used if care is exercised in their use.
C If a long extension cord is used:
1 the marked electrical rating of the extension cord should be at least as great as
the electrical rating of the appliance.
2 if the appliance is of the grounded type, the extension cord should be a
grounding type
3 the cord does not hang from the table to avoid the risk of getting caught up in it.
Page 3
ENGLISH
3
GENERAL INFORMATION
This coffee machine is ideal for preparing espresso coffee either with coffee beans or
pre-ground coffee and also features a device for dispensing steam and hot water.
This elegantly styled machine is designed for household use only. It is not suitable
for continuous professional-type use.
Warning. The manufacturer shall accept no liability for damage or injury
caused by:
• improper use or use for other than the intended purposes;
• repairs carried out by anyone other than an authorized service center;
• tampering with the power cord;
• tampering with any machine component;
• use of spare parts and accessories other than those supplied by the
manufacturer.
• mineral or scale build up and/or freezing damage.
The warranty will be voided in such cases.
TO FACILITATE INTERPRETATION
A warning triangle draws attention to the instructions that are important for user safety. Please carefully abide by these instructions to
avoid serious injury!
This symbol is used to highlight information that is especially important for
ensuring optimal use of the machine.
HOW TO USE THESE OPERATING INSTRUCTIONS
Keep these operating instructions in a safe place and make them available to
anyone else who should use the coffee machine. For further information or an
explanation of problems not completely or sufficiently addressed in these instructions, contact an authorized service center.
TECHNICAL SPECIFICATIONS
• Voltage rating
See rating plate on appliance
• Power rating
See rating plate on appliance
• Casing material
Metal
• Size (w x h x d)
10.3 x 14.2 x 17.2 inches - 260 x 360 x 436 mm
• Weight
26.5 pounds - 12 kg
• Cord length
47.2 inches - 1200 mm
• Control panel
Front (Digital)
• Water tank
67.5 oz - 2 lit. (Removable)
• Power supply
See rating plate on appliance
• Coffee container capacity
(2/3 lb) - (300 g) of coffee beans
• Pump pressure
15 bars
• Boiler
Stainless Steel
• Safety devices
Boiler pressure safety valve
safety thermostat
Subject to engineering and manufacturing changes as warranted by technological
developments.
Machine in conformity with European Directive 89/336/EEC (Italian Legislative
Decree 476 of 04/12/92) concerning electromagnetic compatibility.
The machine complies to American regulations (c UL us) FCC Part. 15 relative to
electromagnetic compatibility.
Page 4
4
IN THE EVENT OF AN EMERGENCY
Immediately unplug the appliance.
THE APPLIANCE MAY ONLY BE USED
- Indoors.
- To prepare coffee, dispense hot water, froth milk or heat beverages using
steam.
- For household use.
- By adults in full control of their physical and mental capacities.
NEVER USE THE APPLIANCE
for purposes other than those indicated above to avoid hazards. Never place any
substances in the containers other than those specified in the instruction manual.
When you fill a container, make sure all nearby containers are closed. Fill the
water tank only with fresh water: hot water and/or other liquids may damage the
machine. Do not use carbonated water. The coffee grinder may be adjusted only
while it is running. Do not introduce your fingers or any material other than coffee
beans into the coffee grinder. Before attempting to access the inside of the coffee
grinder, switch OFF the machine and remove the plug from the outlet. Do not put
coffee beans or instant coffee into the ground coffee container.
POWER SUPPLY
Connect the coffee machine to a suitable outlet. The voltage must match the
voltage specified on the appliance rating plate.
INSTALLATION
- Choose a flat, level supporting surface. Do not place on a hot surface!
- Maintain a distance of 4 in / 10 cm from walls and electric or gas burners.
- Do not keep at temperatures below 32° F / 0° C; freezing may damage the
appliance.
- The power outlet must be accessible at all times.
- The power cord must not be damaged, secured with clamps, placed on very hot
surfaces etc.
- Do not let the power cord hang loosely (Warning: danger of tripping or of
causing the appliance to fall).
- Do not use the power cord to carry or pull the coffee machine.
HAZARDS
- The appliance must not be used by children or by individuals unacquainted with
the operating instructions.
- The appliance is dangerous for children. If left unattended it must be
switched off.
- Do not leave the materials used to pack the appliance within children’s reach.
- Do not direct a jet of hot steam and/or hot water toward yourself or others:
danger of scalding.
- Do not introduce any objects through the openings in the appliance (Electrical
hazard!).
- Do not touch the plug when your hands or feet are wet. Do not unplug the
appliance by pulling on the power cord.
- Warning: contact with hot water, steam or and hot water/steam nozzle may
cause burns.
FAULTS
- Do not use the appliance if it malfunctions or you suspect damage, e.g. after a fall.
- Repairs must be performed by an authorized service center.
- Do not use an appliance with a defective power cord. The cord may only be
replaced by a service center (Electrical hazard!).
- Switch off the appliance before opening the service door. Danger of scalding!
CLEANING
- Before cleaning the appliance, unplug it and allow it to cool down.
- Avoid exposing the appliance to splashes of water. Do not immerse it in water.
- Do not dry machine components in a conventional or microwave oven.
SPARE PARTS
To guarantee safety, you should use only original spare parts and accessories.
DISPOSAL
- The packing materials can be recycled.
- Appliance: unplug the appliance and cut the power cord.
- Deliver the appliance and power cord to a service center or public waste
disposal facility.
SAFETY RULES
Page 5
ENGLISH
5
Dregs drawer /
waste box
Drip tray + grill
ON/OFF switch
Height-adjustable
coffee dispenser
Hot water/
steam wand
Control panel
Steam knob
Cup warming surface
Water tank
Water tank lid
Tray full indicator
Pre-ground
coffee lid
Coffee bean
container
Coffee bean
container lid
Grind adjustment
knob
Doser adjustment
knob
Brew group
Pre-ground
coffee scoop
Water hardness
test strip
Cleaning brush Brew group key
Service door
Digital display
Large coffee button
“Page up” in programming mode
Coffee button
“Page down” in programming mode
Small coffee button
Pre-ground coffee selection button
Programming “MENU” selection button
“OK” in programming mode
Hot water selection button
“ESC” in programming mode
Cartridge filter
applicator
“Aqua Prima”
cartridge filter
Page 6
6
INSTALLATION /
PRIMING
Fill the tank with fresh water.
Move the ON/OFF switch to
“I” to turn on the machine.
The display will signal that
the machine is warming
up.
Place a container under
the steam wand.
Open the knob to prime the
machine.
Wait until a steady stream
of water flows out from the
wand.
The machine is ready for
use.
Fill the coffee bean container with coffee beans.
Remove the drip tray from
the box and put in place on
the machine.
Insert the plug into a suitable outlet.
Close the knob to stop the
flow of water. Remove the
container.
See rating plate
Press the hot water button.
H
OT W
ATE
R
W
AR
MI
NG
UP.
..
R
INS
IN
G
W
AR
MI
NG U
P.
..
SE
LE
CT P
RO
DU
CT
RE
AD
Y FO
R
U
SE
H
OT WA
TE
R
W
AR
MIN
G UP
.
..
Press the hot water button
again to turn off the hot water
feature. Wait for machine to
reach coffee temperature.
Note: Prime th e machine
during initial set up, if the
machine has not been
used for several days, after
refilling the w ater tan k, or
any time the d isplay reads
“VENTILATE”
.
The messages displayed by the machine during operation are shown
on page 18.
The “Aqua Prima” filter can
be installed (see pg.11).
Allow to soak for 30 minutes
prior to first use.
Important warning for using the “Aqua Prima Filter” can be found at
page 18.
Page 7
Page 8
Page 9
ENGLISH
9
STEAM
Place a container with the
beverage to heat up under
the steam wand.
Open the knob.
Close the knob when
finished.
CAPPUCCINO
STEAM - CAPPUCCINO
Warning! Hot water and steam may cause burns! Direct the steam wand towards the drip tray.
Fill a cup to 1/3 with cold
milk.
Position a container under the
steam wand.
Open the knob to discharge
any residual water.
When only steam comes
out, close the knob.
Remove the container.
Open the knob to release
steam.
Move the cup in a circular
motion to heat and froth
the milk evenly.
After frothing the milk,
close the knob.
The machine will signal the
function.
Dispense coffee into the
cup to prepare a delicious
cappuccino.
Position the cup with cold
milk under the steam
wand.
Remove the cup and
place it under the coffee
dispenser.
Remove the container.
Open the knob to eliminate
any residual water.
Heat evenly by making
circular movements.
S
TEA
M
SE
L
ECT P
RO
DUC
T
R
E
AD
Y
F
OR U
SE
S
TEA
M
Page 10
10
The machine must be descaled every 2-3 months, when you observe a diminished flow
of water or when the machine signals that descaling is necessary. The machine must
be on; it automatically controls the distribution of the descaling solution.
DESCALING
Warning! Never use vinegar as a descaling agent.
You can use any
commercially available non-toxic, non-harmful descaling product for coffee
machines. We recommend using a Saeco descaling agent.
DE
SCA
LIN
G
R
EAD
Y
F
OR USE
D
ESC
ALI
NG
REA
DY FO
R US
E
D
ESC
ALI
NG
*
SIG
NAL
.DE
SCA
L.
D
ESC
ALI
NG
FIL
L
W
AT
ERT
ANK
MAC
HIN
E
I
S
DE
SCA
LIN
G
DE
SCA
LIN
G
FI
NI
SHE
D
RI
NSE
MA
CHI
NE
FI
LL
WAT
ERT
AN
K
R
INS
E
M
AC
HIN
E
RIN
S
I
NG
FI
NI
SHE
D
DES
CAL
I
NG
*
SI
GNA
L.D
ES
CAL
.
SIG
NAL
.DE
SCA
L.
*
T
I
MER
SI
GN
AL.
DES
CAL
.
N
O
S
IGN
AL.
DES
CAL
.
YES
SE
LEC
T
P
ROD
UCT
R
EA
D
Y
F
OR U
SE
The machine will display
a message when it needs
descaling.
Press the “M” button.
Place a large container
under the steam wand.
When the descaling
cycle is completed, close
the knob.
On completing the rinse,
close the knob.
Press the “M” button.
If the desca-
ling cycle is
interrupted, the water
tank and internal
machine circuits must
be rinsed.
For further instructions
on how to clear the
descaling signal, see
chapter on programming.
Remove the cartridge
filter carefully. Fill the
tank with the descaling
solution.
Scroll up or down until the
menu "Descaling" appears
on the top of the display.
Open the steam knob.
The machine will start
descaling.
Rinse out the tank and
fill it with fresh water.
Press the “M” button to
select the function.
Press the “M” button. Use the buttons to view
the following menu.
Press the “M” button
twice.
Open the knob to rinse.
Clear the descaling
signal.
Press “esc” to exit the
descaling function.
Page 11
ENGLISH
11
“AQUA PRIMA” CARTRIDGE FILTER
INSTALLATION
The filter must be replaced every 3 months.
Before descaling, remove the filter from the tank.
Remove the filter from the
package.
Adjust the red date indicator
to the current month.
Put the filter into the empty
tank.
Check where the filter
position and reference
mark is.
Insert the applicator and
turn it clockwise to secure
it to the filter.
The reference must be
positioned in correspondence with the groove.
Press down until it is well
seated in place
Turn the applicator counter-clockwise and remove
it from the tank.
Fill the tank with fresh
water and allow filter to
soak in the tank for 30
minutes prior to first use.
Position a container
under the steam wand
and turn the machine on.
Press the hot water
button.
Open the knob to
dispense water through
the steam wand.
Dispense water until the
tank is empty.
Fill the tank with fresh
water.
You can now use your
coffee machine.
It is possible to use the
machine without the Aqua
Prima filter, However,
Saeco suggests its use to
ensure a better tasting cup
of coffee.
H
O
T
W
A
T
E
R
W
A
R
M
IN
G U
P
..
.
Press the hot water button
again to turn off the hot
water feature.
SE
L
E
C
T
P
R
O
D
U
CT
R
E
A
D
Y
F
O
R
US
E
Page 12
12
CLEANING AND MAINTENANCE
Do not dry the machine and/or its components in a microwave and/or
conventional oven.
Do not immerse the machine in water and do not place any of its
components in a dishwasher.
BASIC
CLEANING
Press the PUSH button to
release the brew group.
Unscrew the upper filter screen
using the key provided and wash it
with warm water. Put it back in place
when clean and hand tighten.
Remove the dregs drawer/
waste box.
Open the service door.
Wash the brew group, dry
it and slide back in place.
Do not press the “PUSH”
button.
Put all machine components
back in position.
Close the door.
Clean the machine, its components, and the brew group
at least once a week.
BREW
GROUP
Turn the machine off.
Unplug the machine.
Wash the water tank.
Wash the filter inside it.
Remove the drip tray,
empty it out and wash it.
Use the brush to clean the
pre-ground coffee chute.
Open the service door,
remove the dregs drawer/
waste box, empty it out and
wash it.
Remove cover on "Pannarello" frothing attachment, wash under tap. Wipe spout
left on steam wand with wet cloth. When necessary, unscrew complete assembly
and wash under tap with warm soapy water.
Remove drip tray
Page 13
ENGLISH
13
PROGRAMMING MACHINE FUNCTIONS
The following programming features can be changed to suit your needs.
SELECT PRODUCT
READY FOR USE
ENERGY SAVING *
RINSING
ENERGY SAVING *
RINSING
ENERGY SAVING *
RINSING
ENERGY SAVING *
RINSING
ENERGY SAVING *
RINSING
ENERGY SAVING
SELECT PRODUCT
READY FOR USE
RINSING *
LANGUAGE
RINSING
OFF
RINSING
ON
PROGRAMMING
START
ENERGY
SAVING
RINSING
Press the “M” button to
access the programming
mode.
Use the “∧” and “∨”
buttons to display/change
the menus.
Using the “M” button you can
select the menu item marked
with an “*”
Press ESC to exit without
making any changes.
Use the “M” button to
select a menu or confirm
a change.
The display will show
that the machine is in the
standby mode.
Press the “M” button to
restore the machine to
normal operation.
When this function is activated, the internal machine
circuits will be rinsed immediately after the warming-up
phase to ensure that coffee is prepared with fresh water
only.
From this menu you can
disactivate the function.
When the appliance is used infrequently (i.e. will not be in
use for a period longer than 2 hours), it can be switched to
the STANDBY mode.
With this function you can cut energy costs.
When the function
appears, select it using the
“M” button.
In all new appliances this function has already been
activated in the factory.
Press the “M” button to
confirm your choice.
When the function
appears, select it using the
“M” button.
Page 14
14
PROGRAMMING MACHINE FUNCTIONS
LANGUAGE
This function permits to change the language on the
display. You can select: Italian, German, Portuguese,
Spanish, English, French, Polish, Swedish, and Dutch.
The appliance is usually programmed to the language of
the country in which it is sold.
WATER
HARDNESS
LANGUAGE *
WATER HARDN.
LANGUAGE
ENGLISH
LANGUE
FRANCAIS
WATER HARDN. *
CUP HEATER
WATER HARDN.
HARDNESS 2
CUP HEATER *
TEMPERATURE
CUP HEATER
ON
Dip the test strip in water for
1 second. Check how many
squares change color.
The appliance is factory set on a hardness value of 3. The
setting should be adjusted according to the level of water
hardness to be used with the machine.
The hardness of tap, bottled and filtered water may vary
depending on the region, brand and filter used. For this
reason, the appliance can be set according to the water
hardness to be used, expressed on a scale of 1 to 4 (1 =
soft and 4 = hard).
CUP HEATER
This function allows you to turn on the cup warming surface
on the machine.
Select the desired language.
Choose whether you wish
to turn the cup warming
surface on or off.
Select the corresponding
hardness (e.g. 2 squares =
Hardness 2) and memorize
the value by pressing the
“M” button.
When the function appears, select it using the
“M” button.
When the function appears, select it using the
“M” button.
When the function appears, select it using the
“M” button.
Press the “M” button to
confirm your choice.
Press the “M” button to
confirm your choice.
Page 15
ENGLISH
15
PROGRAMMING MACHINE FUNCTIONS
TEMPERATURE *
PREBREWING
TEMPERATURE
MEDIUM
TEMPERATURE
HIGH
Page 16
Page 17
ENGLISH
17
PROGRAMMING MACHINE FUNCTIONS
DESCALING *
SIGNAL.DESCAL.
DESCALING
DESCALING
TIMER *
RINSING CYCLE
STANDBY
AFTER 3:00
STANDBY
AFTER 1:15
RINSING CYCLE *
FACTOR.SETTINGS
RINSING CYCLE
FILL WATERTANK
RINSING
CYCLE
TIMER
DESCALING
The machine will carry out
a rinsing cycle.
When the cycle is finished
the FILL WATER TANK
message will be displayed.
This function is used to rinse all the coffee-dispensing parts
with water.
The rinsing cycle cannot be interrupted.
A person must be present during this operation.
Use the buttons to adjust
the timer setting.
The switch-off time can be adjusted, in 15-minute intervals,
to a minimum of 15 minutes; the function cannot be
deactivated.
Prepare the machine for
descaling.
This function enables you to activate an automatic
descaling cycle. See page 10 for step by step descaling
instructions.
Warning: a large quantity of water may be
dispensed from the coffee dispenser. Before
starting, empty out the drip tray and keep an additional
container handy.
When the function appears, select it using the
“M” button.
When the function appears, select it using the
“M” button.
When the function appears, select it using the
“M” button.
Carry out an automatic
descaling cycle (see page
10) or press "ESC" to exit if
descaling is not yet needed.
Press the “M” button to
confirm your choice.
This is a factory-set function that automatically switches
the machine into “Standby” after a maximum of 3 hours
have elapsed since the last cup of coffee was dispensed.
Page 18
18
DISPLAY MESSAGES - NOTES ON THE AQUA PRIMA CARTRIDGE FILTER
FACTOR.SETTINGS*
ENERGY SAVING
FACTOR.SETTINGS
NO
FACTOR.SETTINGS
YES
With this function you can restore the machine operating
parameters to the original settings set by the manufacturer.
If you restore all the factory settings, all customized
settings will be lost and you will need to reprogram them
if so desired.
Choose whether to restore
the initial factory settings.
FACTORY
SETTINGS
When the function appears,
select it using the “M” button.
Press the “M” button to
confirm your choice:
ENERGY SAVING
DESCALING
READY FOR USE
FILL WATERTANK
COF BEANS EMPTY
READY FOR USE
DREGDRAWER FULL
BREW UNIT MISS.
INSERT DREGDRAW.
TRAY MISSING
CLOSE DOOR
BREWUNIT BLOCKED
GRINDER BLOCKED
Messages are displayed to guide users through the usage of the machine correctly.
Press “M” .
Descale the machine.
Fill the water tank with fresh water.
Fill the coffee bean container and press the desired
coffee button to start the brewing cycle.
Remove the dregs drawer / waste box and empty out the
used coffee grounds.
Important note: the dregs drawer / waste box may be emptied only when the machine
is ON. The drawer must be removed for at least 5 seconds for the machine to read
that the drawer has been emptied. If you empty the drawer with the machine off, you
will not be able to dispense coffee the next time you switch the machine on.
Put the brew group properly in place.
Put the dregs drawer / waste box properly in place.
Put the drip tray properly in place.
Close the front door.
Contact an authorized service center.
ADDITIONAL INFORMATION FOR CORRECTLY USING THE “AQUA PRIMA”
FILTER.
Please follow these simple instructions to correctly use the “Aqua prima” filter:
1. Keep the “Aqua prima” filter cool and away from sunlight; the room temperature should
be between 41°F/+5°C and 104°F/+40°C;
2. Do not use the filter in temperatures over 140°F/60°C.
3. If the coffee machine is not used for 3 days, we recommend washing the “Aqua prima”
filter;
4 If the coffee machine is not used for more than 20 days, it is advisable to replace the
filter.
5. To store an already opened filter, seal it in a nylon bag and keep in the fridge; do not
store it in the freezer to avoid damaging the filter properties.
6. Before using the filter, leave it to soak in the water tank for 30 minutes.
7. Once it is taken out of its packaging, do not keep the filter in the open air.
8. The filter must be replaced 90 days after opening the package or after treating 13 gal-
lons/60 litres of water.
Page 19
ENGLISH
19
PROBLEMS CAUSES REMEDIES
The brewing cycle does
not start.
No coffee beans / “Cof Beans
Empty”.
Refill bean hopper and press
desired coffee button.
No water / “Fill watertank”. Fill water tank. Make sure float is
in position and held in place by the
cap. Message will clear.
Dredge drawer / waste box is
full / “Dredgedrawer full”.
Remove waste box while machine
is on. Leave out for 5-10 seconds
and put back in machine. Message
will clear.
Brew group missing / “Brew Unit
Miss.”
Remove drip tray, waste box and
brew group. Put brew group back
in machine until securely locks in
place, put waste box in, shut service
door and put drip tray back in place.
Coffee flows too quickly. Grind is too coarse. Adjust the grinder to a finer grind,
ex. from 5 to 3. Adjust only while
grinder is grinding and only a
maximum of 2 settings at a time. It
will take 3-4 cups to see results.
Dose needs to be increased. Turn doser towards + sign.
Coffee flows too slowly. Grind is too fine. Adjust the grinder to a coarser
grind, ex. from 5 to 7. Adjust only
while grinder is grinding and only a
maximum of 2 settings at a time. It
will take 3-4 cups to see results.
Dose needs to be decreased. Turn doser towards - sign.
Filter screen in brew group is
clogged.
Clean the filter screen using the
key provided.
The machine does not
turn on.
The machine is not connected to
the power supply.
Move the main switch to ON (“I”
position).
Check the plug and the power
outlet.
The coffee is not hot
enough.
The cups are cold. Warm up the cups on cup warmer
or by dispensing a little hot water
into the cup and letting it sit for a
few seconds.
A low temperature has
been set.
Set the machine to a higher
temperature.
PROBLEMS - CAUSES - REMEDIES
PROBLEMS CAUSES REMEDIES
Only water is dispensed
when you select “pre-ground
coffee”.
No pre-ground coffee has been
put into the pre-ground chute.
Select Pre-ground coffee button,
put pre-ground coffee into the
chute and press the desired coffee
button.
Too much pre-ground coffee put
in chute.
Put one level scoop of espresso
coffee. Max. 1 cup at a time.
No hot water or steam
is dispensed.
The steam wand is clogged. Clear it with a thin needle or pin.
During this operation, the
knob must be closed and
the machine must be off.
Then run water through steam
wand to make sure unclogged.
Reduced amount of coffee,
water and steam coming out
of the machine; the machine
takes longer to heat .
Lime scale / mineral build up in
machine.
Descale the machine. If not done
for a long period of time, we
recommend doing 2 cycles (see
instructions on page 10).
Unable to clear Descale
message.
Need to reset message. Go into programming mode, “Sign.
Decal.” and reset message.
The brew group cannot be
removed.
The brew group is out of
alignment.
Put waste box in position, close
door and put drip tray in position.
Switch machine on; the brew group
will reset into original position.
Ventilate Machine needs to be primed. Dispense 3-4 oz of water through
the steam wand.
Steam wand clogged. Clear steam wand and prime
machine.
Limescale / mineral build up in
machine.
Descale the machine. If not done
for a long period of time, we
recommend doing 2 cycles (see
instructions).
Questions?
US Customers
Contact Saeco USA Customer Service at 1-800-933-7876
Canada Customers
Contact Saeco Canada at 1-514-385-5551
Page 20
Saeco International Group S.p.A. - Via Panigali, 39
40041 Gaggio Montano - Bologna - Italy
Tel. +39 0534.771.111 - Fax. +39 0534.31025 - http://www.saeco.com
Cod. 1.6.589.79.02 Rev.01 del 08-07-04
Loading...