Automatic espresso coffee machine
Model
Modular CAPPUCCINO
Type: CAP001B
USO E MANUTENZIONE
TABLE OF CONTENTS
English page 10 ÷ 14
1 - MANUAL INTRODUCTION. ........................................... 10
1.1 Foreword ..........................................................................10
1.2 Symbols Used ....................................................................10
2 - MACHINE INFORMATION. ............................................10
2.1 Intended use of machine ......................................................10
3 - SAFETY. ..........................................................................10
3.1 General safety regulations ....................................................10
3.2 Operator requirements ......................................................... 10
4 - DESCRIPTION OF CONTROLS AND TOOLS. .................11
4.1 Controls ............................................................................ 11
4.2 Cappuccino dispensing unit .................................................11
5 - USING THE CAPPUCCINATORE. ....................................11
5.1 Warnings..........................................................................11
5.2 Coffee with a dash of milk dispensing .................................... 12
5.3 Cappuccino dispensing .......................................................12
5.4 Hot milk dispensing .............................................................12
5.5 Programming dispenser keys ................................................. 12
5.6 Cream adjustment ..............................................................13
5.7 Display messages ...............................................................13
6 - MAINTENANCE.............................................................. 13
6.1 Foreword ..........................................................................13
6.2 Cleaning the CAPPUCCINATORE .......................................... 13
6.2.1Cappuccino dispensing unit ................................................. 13
2
fig. 1 • Abb.1
1a 1b 1c
1
2
3
4
5
6
PARTI PRINCIPALI
1 Pannello comandi cappuccinatore
1a Tasto caffè macchiato
1b Tasto cappuccino
1c Tasto latte caldo
2 Spillo di regolazione
3 Copertura erogatore
4 Tubo erogatore
5 Pinza blocca tubo
6 Tubo di aspirazione latte
MAIN PARTS
1 Cappuccino device control panel
1a Coffee with a dash of milk key
1b Cappuccino key
1c Hot milk key
2 Adjusting pin
3 Dispensing unit cover
4 Dispensing spout
5 Retaining clip for milk supply tube
6 Milk supply tube
PARTES PRINCIPALES
1 Panel de mandos dispositivo preparación
café con leche
1a Tecla café cortado
1b Tecla cappuccino
1c Tecla leche caliente
2 Mando regulación crema
3 Protección salida café
4 Tubo de salida
5 Pinza de bloqueo tubo
6 Tubo de aspiración leche
It
En
Sp
HAUPTELEMENTE
1 Bedienungsfeld des Cappuccinatore
1a Taste Kaffee mit einem Schuß Milch
1b Taste Cappuccino
1c Taste heiße Milch
2 Einstellnadel zur Milchaufschäumung
3 Abdeckung Brühgruppe
4 Auslaufrohr
5 Schlauchklemme
6 Milchansaugschlauch
PARTES PRINCIPAIS
1 Painel de comandos ”cappuccinatore”
1a Tecla café garoto
1b Tecla ”cappuccino”
1c Tecla leite quente
2 Agulha de regulação
3 Cobertura grupo de distribuição
4 Tubo de distribuição
5 Pinça trava tubo
6 Tubo de aspiração do leite
De Fr
Pt
PARTIES PRINCIPALES
1 Tableau de commande du dispositif à
café crème (cappuccinatore)
1a Touche café avec une goutte de lait
1b Touche café crème
1c Touche lait chaud
2 Pointeau de réglage
3 Carter distributeur
4 Tuyau de distribution
5 Pince serre-tuyau
6 Tuyau d’aspiration lait
BELANGRIJKSTE
ONDERDELEN
1 Bedieningspaneel cappuccinobereider
1a Toets koffie met melk
1b Toets cappuccino
1c Toets warme melk
2 Afstelnaald voor schuim
3 Afdekking schenkinrichting
4 Schenkleiding
5 Buisklem
6 Melk-aanzuigbuisje
Nl
4
English
1 MANUAL INTRODUCTION
1.1 Foreword
Important
This manual is an integral part of the LUXE kit of the MODULAR machine, and regards the CAPPUCCINO model. It should
therefore be issued with the Instruction and Maintenance
booklet for the MODULAR LUXE E COFFE machine.
The aim of this manual is to provide all instructions and
maintenance information necessary (procedures within user
competence) for this model.
Both this manual and the MODULAR machine Instruction and
Maintenance manual should be read before using the cappuccino device CAPPUCCINATORE, to ensure a good working
knowledge of the equipment.
Manufacturer: Cosmec S.p.A.
Via Panigali, 39, 40041 GAGGIO MONTANO (BO)
This manual should be carefully kept near the CAPPUCCINATORE
at all times, even when the machine changes hands. Should the
manual be damaged or lost, apply immediately to an AUTHORISED service centre for a copy.
2. MACHINE INFORMATION
2.1 Intended use of machine
The fully automatic and programmable CAPPUCCINATORE pro-
duces:
- drinks with milk and freshly ground coffee;
- hot milk.
Important
In case of incorrect usage the guarantee is void and the manufac-
turer declines all responsibility for damage to persons and/or
objects.
The following are considered to be incorrect uses:
- any use other than that described and/or using different techniques to those indicated herein;
- any modifications to the CAPPUCCINATORE which contrasts
with the indications herein;
- any use following tampering with components and/or modifications of safety devices.
3. SAFETY
1.2 Symbols Used
Various warnings are included in this manual to highlight the different levels of danger or competence.
Danger
This is used to indicate dangerous situations for
CAPPUCCINATORE users and for the machine itself.
Maintenance Technician
This indicates the procedures which should only be carried
out by the specialised maintenance personnel.
Important
Indicates procedures which should be carried out in order to
maintain the CAPPUCCINATORE in good working order.
3.1 General safety regulations
• Read this manual carefully before using the machine.
• Deactivation of the safety devices installed in the CAPPUCCINATORE is strictly prohibited.
• For cleaning procedures the main switch or all-pole switch must
be in the “0” position or the machine unplugged from the power
source.
• Do not independently modify any parts of the CAPPUCCINATORE: failure to comply with this specification will result in
annulment of manufacturer responsibility.
• Do not spray or splash CAPPUCCINATORE with water.
3.2 Operator requirements
For safety reasons two types of operators are required, with different capacities:
10
Maintenance technician
Person authorised to install, set up, regulate and generally maintain the CAPPUCCINATORE.
English
User
Person authorised exclusively to operate and oversee the CAPPUCCINATORE. The user may switch on the CAPPUCCINATORE,
regulate the working parameters, stop the device and load the
coffee beans.
In case of any malfunction of the CAPPUCCINATORE the user
must request the intervention of the maintenance technician.
Danger
The user must not carry out procedures indicated in this manual
as the specific responsibility of the maintenance technician.
4 - DESCRIPTION OF
CONTROLS AND TOOLS
Important
The CAPPUCCINATORE is supplied with dispensing buttons
pre-programmed to standard settings (see Fig. 1).
- cappuccino device casing (fig. 2, 8)
- pin for regulation of froth quality (fig. 2, 2)
- adjustable dispensing spout (fig. 2, 4)
8
4
fig. 2
5 - USING THE
CAPPUCCINATORE
5.1 Warnings
2
5
6
4.1 Controls
The “CAPPUCCINO” model is set up with the following controls
(see fig. 1):
Coffee with a dash of milk key (Fig. 1, 1a)
(See “5.2 Coffee with a dash of milk dispensing”)
Programmable (See “5.5 Programming dispenser
keys”)
Cappuccino key (Fig. 1, 1b)
(See “5.3 Cappuccino dispensing”)
Programmable (See “5.5 Programming dispenser
keys”)
Hot milk key (Fig. 1, 1c)
(See “5.4 Hot milk dispensing”)
Programmable (See “5.5 Programming dispenser
keys”)
Froth adjusting pin (Fig. 1, 2)
Vertical position can be manually adjusted (See “5.6
Froth adjustment”)
Display control panel
(See Instruction and Maintenance booklet for MODULAR machine)
• Before daily start up of the CAPPUCCINATORE carry out the
following procedures:
- remove, clean and reinsert the pin regulating froth quality.
Failure to reinsert the pin in the hole will prevent siphoning
of milk from the container.
- Insert free end of milk supply tube into container.
- insert the milk supply tube in the retaining clip.
Never remove the milk supply tube from the clip during use
of the cappuccino device.
• Each time the CAPPUCCINATORE controls are activated, the
machine carries out an automatic cycle which consists of:
- internal discharge of condensation inside spouts;
- siphoning of milk;
- drink dispensing;
- steam cleaning of spout.
• The milk used in the CAPPUCCINATORE must be kept in a
refrigerator and must never be left outside the refrigerator for
longer than 30 minutes.
• If the CAPPUCCINATORE is not used for more than an hour,
carry out a cleaning cycle of the spouts before re-using.
To clean the spouts:
- immerse the milk supply tube in a container of water;
- press the milk key ;
- wait until the water has been dispensed.
4.2 Cappuccino dispensing unit
The cappuccino dispensing unit (fig. 2) consists of:
- milk supply tube (fig. 2, 6)
- retaining clip for milk supply tube (fig. 2, 5)
PLEASE NOTE: Do not use hot water.
11
English
5.2 Coffee with a dash of milk dispensing
This drink consists of freshly ground and freshly brewed coffee
dispensed by the coffee dispensing unit, to which a dash of warm
milk is added by the cappuccino dispensing unit.
- Insert the milk supply tube (fig. 1, 6) into the milk container.
- Press the key.
“COFFEE WITH A DASH OF MILK” will appear on the display.
During the dispensing process “PREBREWING” will appear on the
display, if activated by the menu (see the Instruction and Maintenance manual of the MODULAR machine), while to the side of this
an icon will appear showing a container being filled.
When dispensing finishes “READY FOR USE” will appear on the
display.
5.3 Cappuccino dispensing
container being filled.
When dispensing finishes “READY FOR USE” will appear on the
display.
5.5 Programming dispenser keys
All the dispensing keys , and have a self-instructing
memory. Once programmed they will dispense the same quantity
of the drink each time they are activated.
To programme (or re-programme) the and keys, set the
dosage of coffee and milk in the drink independently, using the
following two procedures.
To programme (or re-programme) the or keys:
- Switch on the machine;
- prepare the machine for use;
- place a container under the dispensing spout (fig. 1, 4);
This drink consists of frothed milk dispensed by the CAPPUCCINATORE dispensing unit to which freshly ground and freshly brewed
coffee is added by the coffee dispensing unit.
- Insert the milk supply tube (fig. 1, 6) into the milk container.
- Press the key.
“CAPPUCCINO” will appear on the display;
- Regulate the quality of froth to be dispensed (see 5.1 Froth
regulation) using the pin (fig. 1, 2).
During the dispensing process “PREBREWING” will appear on the
display, if activated by the menu (see the Instruction and Maintenance manual of the MODULAR machine), while to the side of this
an icon will appear showing a container being filled.
When dispensing finishes “READY FOR USE” will appear on the
display.
5.4 Hot milk dispensing
This drink consists only of hot milk dispensed by the CAPPUCCINATORE dispensing unit.
- press and continue to press (for more than 4 seconds) the
or key.
PROGRAMMING COFFEE WITH A DASH OF MILK or PROGRAMMING CAPPUCCINO will appear on the display.
The machine will carry out a grinding cycle and dispense the coffee.
- Release the or key when the desired quantity of
coffee has been dispensed. This quantity is now automatically
memorised.
To programme the milk portion:
- press and continue to press (for more than 4 seconds) the key.
PROGRAMMING MILK will appear on the display.
- Release the key.
- press and continue to press (for more than 4 seconds) the
or key.
The CAPPUCCINATORE will discharge the condensation in
the spouts, take the milk and dispense it into the container.
- Release the o key.
The CAPPUCCINATORE will discharge steam from the spout.
- Insert the milk supply tube (fig. 1, 6) into the milk container.
- Press the key.
“HOT MILK” will appear on the display;
- Regulate the quality of froth to be dispensed (see 5.1 Froth
regulation) using the pin (fig. 1, 2).
During the dispensing process an icon will appear showing a
12
Activate the keys briefly (less than 1 second) to obtain the programmed drink.
To programme (or re-programme) the key:
-
press and continue to press (for more than 4 seconds) the key.
PROGRAMMING MILK will appear on the display.
- Release the key.
- press and continue to press the key.
English
The CAPPUCCINATORE will discharge the condensation in the
spouts, take the milk and dispense it into the container.
- Release the key to automatically memorise the quantity of milk
dispensed; the CAPPUCCINATORE will discharge steam from
the spout.
Activate the keys briefly (less than 1 second) to obtain the programmed quantity.
Important
The programmed data settings remain in the machine memory
even when there is no electrical power.
5.6 Froth adjustment
The quality of froth in the drinks is proportional to the vertical position of the pin above the hole (see fig.3). To obtain a large quantity of froth raise the pin, and lower it to obtain a small quantity
(see fig.3). Never remove the pin or completely insert it into the
hole.
6 - MAINTENANCE
6.1 Foreword
Danger
Before carrying out maintenance and/or cleaning procedures,
disconnect the electrical power supply using the main switch
(see Instruction and Maintenance booklet for MODULAR
machine) and the all-pole switch (or by unplugging) and wait
for the machine to cool down.
- Non-removable components should only be cleaned with
cold or tepid water (unless otherwise specified) using nonabrasive sponges and damp cloths.
- Do not spray water directly onto the machine.
- All the parts to be cleaned are easily accessible and do
not require special equipment.
- Regular cleaning and maintenance will preserve the
machine’s efficient working conditions for a longer period
and guarantee conformity with hygiene standards.
fig. 3
5.7 Display messages
On the machine display a series of messages are shown other
than those already described (see Instruction and Maintenance
booklet for MODULAR machine).
WATER SUPPLY - PRESS KEY ^: this message appears when the
machine detects absence of water during drink dispensing.
PROGRAMMING: appears when programming the machine (see
“6.14 Functions programmable from the menu” - see Instruction and Maintenance booklet for MODULAR machine).
Danger
In case of malfunctions normally signalled on the display,
switch off the machine immediately, disconnect the power
supply using the all-pole switch or by unplugging, and contact
the nearest service centre.
6.2 Cleaning the CAPPUCCINATORE
Danger
Do not carry out any cleaning procedures on the cappuccino
device when the machine is on standby.
Cleaning should be carried out after each use of the
CAPPUCCINATORE to avoid drying of milk residue.
All removable components must be washed and rinsed in
running water.
Important
Never wash the components in dishwashing machines.
PLEASE NOTE: The visual display messages are accompanied
by an intermittent beeping sound.
6.2.1 Cappuccino dispensing unit
To clean the cappuccino dispensing unit components individually
(fig.4) the following must be removed:
- the upper casing (fig. 4,3), removing it upwards;
- the froth adjusting pin (fig.4, 2);
- the air diffuser (fig.4, 7) from the cappuccino device casing, in
an upwards direction;
- the cappuccino device casing (fig.4,8) pulling it towards you;
13
English
- the connection fitting (fig.4, 9) from the milk supply tube to the
cappuccino device casing;
- the adjustable dispensing spout (fig.4,4);
- the milk supply tube (fig.4, 6).
Important
For all machine maintenance refer to the Instruction and
Maintenance booklet for MODULAR machine.
3
2
7
8
9
4
6
fig. 4
PROGRAMMING
5 secs.
LANGUAGE
CUPWARMER
GRINDER SETTING
TEMPERATURES
PREINFUSION
HOT WATER PROGRAMM.
MILK PROGRAMMING
HOT WATER MIXING
RINSING PROGRAMMED
GROUP RINSING
CLOCK
ITALIANO
DEUTSCH
FRANCAIS
ETC.
ON
OFF
1 SMALL CUP
2 SMALL CUPS
1 LARGE CUP
2 LARGE CUPS
JUG
COFFEE & MILK
CAPPUCCINO
COFFEE
COFFEE & MILK
CAPPUCCINO
FIRST COFFEE
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OBSERVE THE INSTRUCTIONS
09:32 M 12 MAR 97
MIN. XXX
LOW
STANDARD
HIGH
LOW
STANDARD
HIGH
14
AUTOMATIC OPERATION
ON/OFF TIME
COUNTERS
ANTIFREEZING
UNBLOCKING
OFF
ON
ON 1:MTWTFss 00:00
OFF 1:MTWTFss 00:00
ON 2:mtwtfss 00:00
OFF 2:mtwtfss 00:00
ON 3:mtwtfss 00:00
OFF 3:mtwtfss 00:00
ON 4:mtwtfss 00:00
OFF 4:mtwtfss 00:00
TOTAL COFFEE 000000
TOTAL WATER 000000
ON
OFF
CODE: 0000
Loading...