Philips AVENT Avent SCF260/34, 852022, N0600 Troubleshooting Manual

TROUBLE SHOOTING GUIDE

Philips Avent SCF260/34 Digital Bottle Warmer 852022

Supplier: Philips Avent
Product: Digital BOTTLE WARMER 220-240V
SKU: 852022 (Philips SKU - SCF260/34)
Style No: N0600

HEATING

1. Q: Food is not warm enough.
A: The temperature of warmed food depends on the consistency of the food. Philips AVENT
recommends that, ideally, pureed food only should be heated with this warmer. If you find that thicker
food is not warm enough at the end of the warming cycle, fill the warmer with an additional 30ml/1oz of
water. On step 4 and 5 of the User Instructions, choose the food from room temperature mode and
programme the warmer at the 30ml/1oz option. Before feeding your baby, stir the food. Always check
food temperature before feeding.

2. Q: Milk is not warm enough.
A: If you find that milk is not warm enough at the end of a warming cycle, fill the warmer with an
additional 30ml/1oz of water. On step 4 and 5 of the User Instructions, choose the milk from room
temperature mode and programme the warmer at the 30ml/1oz option. Before feeding your baby, shake
the bottle or storage container gently and check the temperature of the milk by sprinkling a few drops on
the back of your hand.

DISPLAY

3. Q: Display will not illuminate / Warmer will not turn on.
A: Check that the lid is closed correctly. Check that the mains lead is plugged into the mains and the
power outlet is switched on. Then hold the Power/Mode Selection Button for 3 seconds.

4. Q: Symbols on the display are flashing.
A: If the milk, room temperature and ml/oz symbols are flashing, then the lid has not been closed
correctly.
A: If all volume symbols are flashing, and the warmer beeps intermittently for 30 seconds then the
cycle is complete. Follow Step 8 onwards of the User Instructions to remove the bottle or container from
the warmer.
A: If all mode and starting temperature symbols are flashing, then the unit requires de-scaling. See
section ‘Care of your iQ Bottle and Baby Warmer’ on page 6 of the User Instructions. To acknowledge the
de-scale warning, press and hold the Power/Mode Selection or Volume Selection/Start Button for 3
seconds. If you do not wish to de-scale, please be aware that this may cause irreparable damage.

5. Q: The warmer is beeping.
A: If ml/oz symbols flash and the warmer beeps twice, insufficient water has been placed in the
warmer. Unplug the warmer, discard the milk or food and empty any remaining water. Be careful as the
warmer is hot. Follow User Instructions from Step 1 onwards.
A: If all volume symbols are flashing, and the warmer beeps intermittently for 30 seconds then the
cycle is complete. Follow Step 8 onwards of the User Instructions to remove the bottle or container from
the warmer.

TROUBLE SHOOTING GUIDE

Philips Avent SCF260/34 Digital Bottle Warmer 852022

CYCLE

6. Q: To stop the warming cycle.
A: Press the Power/Mode Selection Button and the warmer will beep and return to default settings.

7. Q: To start the warming cycle.
A: Once the correct mode, starting temperature and volume have been selected, press and hold the
Volume Selection/Start Button until the warmer beeps.

8. Q: If the lid is opened during warming cycle.
A: If the lid is opened at any time during the warming cycle, the lights on the display panel will flash and
the warmer will stop and return to default settings. In order to reset the warmer after the lid has been
opened, empty out any residual water, and then follow instructions for use from step 1 onwards. Since
this could occur at any stage of the warming cycle, milk or food should be discarded for safety reasons.

9. Q: Difficulty setting the appropriate amount of frozen food.
A: The maximum volume that may be selected when warming food from frozen is 230ml/8oz.

Customer Care Number Customer Care opening times
0800 289 064 Weekdays: Mon – Fri 9:00 am – 4:30 pm

Website: www.philips.co.uk