Philips X2692CK Datasheet

 
SCC2692
Dual asynchronous receiver/transmitter (DUART)
Product specification Supersedes data of 1998 Feb 19 IC19 Data Handbook
INTEGRATED CIRCUITS
Philips Semiconductors Product specification
SCC2692Dual asynchronous receiver/transmitter (DUART)
2
1998 Sep 04 853–0895 19971
DESCRIPTION
The Philips Semiconductors SCC2692 Dual Universal Asynchronous Receiver/Transmitter (DUART) which is compatible with the SCN2681. It is a single-chip CMOS-LSI communications device that provides two full-duplex asynchronous receiver/transmitter channels in a single package. It interfaces directly with microprocessors and may be used in a polled or interrupt driven system.
The operating mode and data format of each channel can be programmed independently. Additionally, each receiver and transmitter can select its operating speed as one of eighteen fixed baud rates, a 16X clock derived from a programmable counter/timer, or an external 1X or 16X clock. The baud rate generator and counter/timer can operate directly from a crystal or from external clock inputs. The ability to independently program the operating speed of the receiver and transmitter make the DUART particularly attractive for dual-speed channel applications such as clustered terminal systems.
Each receiver is quadruply buffered to minimize the potential of receiver over-run or to reduce interrupt overhead in interrupt driven systems. In addition, a flow control capability is provided to disable a remote DUART transmitter when the receiver buffer is full.
Also provided on the SCC2692 are a multipurpose 7-bit input port and a multipurpose 8-bit output port. These can be used as general purpose I/O ports or can be assigned specific functions (such as clock inputs or status/interrupt outputs) under program control.
FEA TURES
Dual full-duplex asynchronous receiver/transmitters
Quadruple buffered receiver data register
Programmable data format
5 to 8 data bits plus parityOdd, even, no parity or force parity1, 1.5 or 2 stop bits programmable in 1/16-bit increments
16-bit programmable Counter/Timer
Programmable baud rate for each receiver and transmitter
selectable from:
22 fixed rates: 50 to 115.2k baudNon-standard rates to 115.2Kb
Non-standard user-defined rate derived from programmable
counter/timer
– External 1X or 16X clock
Parity, framing, and overrun error detection
False start bit detection
Line break detection and generation
Programmable channel mode
Normal (full-duplex)Automatic echoLocal loopbackRemote loopbackMultidrop mode (also called ‘wake-up’ or ‘9-bit’)
Multi-function 7-bit input port
Can serve as clock or control inputsChange of state detection on four inputsInputs have typically >100k pull-up resistors
Multi-function 8-bit output port
Individual bit set/reset capabilityOutputs can be programmed to be status/interrupt signals
Versatile interrupt system
– Single interrupt output with eight maskable interrupting
conditions
– Output port can be configured to provide a total of up to six
separate wire-ORable interrupt outputs
Maximum data transfer rates: 1X – 1MB/sec, 16X – 125kB/sec
Automatic wake-up mode for multidrop applications
Start-end break interrupt/status
Detects break which originates in the middle of a character
On-chip crystal oscillator
Power down mode
Receiver timeout mode
Commercial and industrial temperature range versions
TTL compatible
Single +5V power supply
ORDERING INFORMATION
COMMERCIAL INDUSTRIAL
DESCRIPTION
VCC = +5V +10%,
TA = 0 to +70°C
VCC = +5V +10%, TA = -40 to +85°C
DWG #
40-Pin Plastic Dual In-Line Package (DIP)
1
SCC2692AC1N40 SCC2692AE1N40 SOT129-1
28-Pin Plastic Dual In-Line Package (DIP)
1
SCC2692AC1N28 SCC2692AE1N28 SOT117-1 44-Pin Plastic Leaded Chip Carrier (PLCC) Package SCC2692AC1A44 SCC2692AE1A44 SOT187-2 44–Pin Plastic Quad Flat Pack (PQFP) SCC2692AC1B44 SCC2692AE1B44 SOT307–2
NOTE:
1. For availability, please contact factory.
Philips Semiconductors Product specification
SCC2692Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
3
PIN/FUNCTION PIN/FUNCTION
1NC 23NC 2 A0 24 INTRN 3 IP3 25 D6 4A1 26D4 5 IP1 27 D2 6A2 28D0 7 A3 29 OP6 8 IP0 30 OP4 9 WRN 31 OP2 10 RDN 32 OP0 11 RXDB 33 TXDA 12 NC 34 NC 13 TXDB 35 RXDA 14 OP1 36 X1/CLK 15 OP3 37 X2 16 OP5 38 RESET 17 OP7 39 CEN 18 D1 40 IP2 19 D3 41 IP6 20 D5 42 IP5 21 D7 43 IP4 22 GND 44 V
CC
24 23
22 2120
19
18
17
16
15
28 27
12
10 11
9
8
7
6
5
4
3
2
1
14
13
26 25
29
30
31
32
33
34
35
36
37
38
39
40
DIP
V
CC
IP4 IP5
IP6 IP2
CEN RESET
X2 X1/CLK RxDA TxDA OP0
OP2 OP4 OP6 D0 D2 D4
D6 INTRN
A0
IP3
A1
IP1
A2
A3
IP0
WRN
RDN
RxDB
TxDB
OP1
OP3 OP5 OP7
D1 D3 D5
D7
GND
24
23 22 21 20 19 18
17
16 15
28 27
12
10 11
9
8
7
6
5
4
3
2
1
14
13
26 25
V
CC
IP2 CEN
RESET X2
X1/CLK RxDA TxDA OP0 D0 D2
D4
D6 INTRNGND
D7
D5
D3
D1
OP1
TxDB
RxDB
RDN
WRN
A3
A2
A1
A0
DIP
1
39
17
28
40
29
18
7
PLCC
6
INDEX
CORNER
SD00131
PIN/FUNCTION PIN/FUNCTION
1 A3 23 N/C 2 IP0 24 OP6 3 WRN 25 OP4 4 RDN 26 OP2 5 RxDB 27 OP0 6 TxDB 28 TxDA 7 OP1 29 RxDA 8 OP3 30 X1/CLK 9 OP5 31 X2 10 OP7 32 RESET 11 N/C 33 CEN 12 D1 34 IP2 13 D3 35 IP6 14 D5 36 IP5 15 D7 37 IP4 16 GND 38 V
CC
17 GND 39 V
CC
18 INTRN 40 A0 19 D6 41 IP3 20 D4 42 A1 21 D2 43 IP1 22 D0 44 A2
TOP VIEW
33
11
22
34
23
12
1
PQFP
44
TOP VIEW
Figure 1. Pin Configurations
ABSOLUTE MAXIMUM RATINGS
1
SYMBOL
PARAMETER RATING UNIT
T
A
Operating ambient temperature range
2
Note 4 °C
T
STG
Storage temperature range -65 to +150 °C
V
CC
Voltage from VCC to GND
3
-0.5 to +7.0 V
V
S
Voltage from any pin to GND
3
-0.5 to VCC +0.5 V Package power dissipation DIP28 1.22 W Package power dissipation DIP40 2.97 W
P
D
Package power dissipation PLCC44 2.66 W Package power dissipation PQFP44 2.08 W Derating factor above 25°C DIP28 19 mW/°C Derating factor above 25°C DIP40 24 mW/°C Derating factor above 25°C PLCC44 21 mW/°C Derating factor above 25°C PQFP44 17 mW/°C
NOTES:
1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other condition above those indicated in the operation section of this specification is not implied.
2. For operating at elevated temperatures, the device must be derated.
3. This product includes circuitry specifically designed for the protection of its internal devices from damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying any voltages larger than the rated maxima.
4. Parameters are valid over specified temperature range.
Philips Semiconductors Product specification
SCC2692Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
4
BLOCK DIAGRAM
8
D0–D7
RDN
WRN
CEN
A0–A3
RESET
INTRN
X1/CLK
X2
4
BUS BUFFER
OPERATION CONTROL
ADDRESS
DECODE
R/W CONTROL
INTERRUPT CONTROL
IMR ISR
TIMING
BAUD RATE
GENERATOR
CLOCK
SELECTORS
COUNTER/
TIMER
XTAL OSC
CSRA
CSRB
ACR
CTLR
CHANNEL A
TRANSMIT
HOLDING REG
TRANSMIT
SHIFT REGISTER
RECEIVE
HOLDING REG (3)
RECEIVE
SHIFT REGISTER
MRA1, 2
CRA SRA
INPUT PORT
CHANGE OF
STATE
DETECTORS (4)
OUTPUT PORT
FUNCTION
SELECT LOGIC
OPCR
TxDA
RxDA
IP0-IP6
OP0-OP7
V
CC
GND
CONTROL
TIMING
INTERNAL DATABUS
CHANNEL B (AS ABOVE)
IPCR
ACR
OPR
CTLR
U
RxDB
TxDB
8
7
SD00132
Figure 2. Block Diagram
Philips Semiconductors Product specification
SCC2692Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
5
PIN DESCRIPTION
APPLICABLE
SYMBOL
40,44 28
TYPE
NAME AND FUNCTION
D0-D7 X X I/O Data Bus: Bidirectional 3-State data bus used to transfer commands, data and status between the
DUART and the CPU. D0 is the least significant bit.
CEN X X I Chip Enable: Active-Low input signal. When Low, data transfers between the CPU and the DUART
are enabled on D0-D7 as controlled by the WRN, RDN and A0-A3 inputs. When High, places the D0-D7 lines in the 3-State condition.
WRN X X I Write Strobe: When Low and CEN is also Low, the contents of the data bus are loaded into the
addressed register. The transfer occurs on the rising edge of the signal.
RDN X X I Read Strobe: When Low and CEN is also Low, causes the contents of the addressed register to be
presented on the data bus. The read cycle begins on the falling edge of RDN.
A0-A3 X X I Address Inputs: Select the DUART internal registers and ports for read/write operations.
RESET X X I Reset: A High level clears internal registers (SRA, SRB, IMR, ISR, OPR, OPCR), puts OP0-OP7 in
the High state, stops the counter/timer, and puts Channels A and B in the inactive state, with the TxDA and TxDB outputs in the mark (High) state. Resets Test modes, MR pointer set to MR1.
INTRN X X O Interrupt Request: Active-Low, open-drain, output which signals the CPU that one or more of the
eight maskable interrupting conditions are true.
X1/CLK X X I Crystal 1: Crystal connection or an external clock input. A crystal of a clock the appropriate frequency
(nominally 3.6864 MHz) must be supplied at all times. For crystal connections see Figure 7, Clock Timing.
X2 X X I Crystal 2: Crystal connection. See Figure 7. If a crystal is not used it is best to keep this pin not
connected although it is permissible to ground it.
RxDA X X I Channel A Receiver Serial Data Input: The least significant bit is received first. “Mark” is High,
“space” is Low.
RxDB X X I Channel B Receiver Serial Data Input: The least significant bit is received first. “Mark” is High,
“space” is Low.
TxDA X X O Channel A Transmitter Serial Data Output: The least significant bit is transmitted first. This output is
held in the “mark” condition when the transmitter is disabled, idle or when operating in local loopback mode. “Mark” is High, “space” is Low.
TxDB X X O Channel B Transmitter Serial Data Output: The least significant bit is transmitted first. This output
is held in the ‘mark’ condition when the transmitter is disabled, idle, or when operating in local loopback mode. ‘Mark’ is High, ‘space’ is Low.
OP0 X X O Output 0: General purpose output or Channel A request to send (RTSAN, active-Low). Can be
deactivated automatically on receive or transmit.
OP1 X X O Output 1: General purpose output or Channel B request to send (RTSBN, active-Low). Can be
deactivated automatically on receive or transmit.
OP2 X O Output 2: General purpose output, or Channel A transmitter 1X or 16X clock output, or Channel A
receiver 1X clock output.
OP3 X O Output 3: General purpose output or open-drain, active-Low counter/timer output or Channel B
transmitter 1X clock output, or Channel B receiver 1X clock output. OP4 X O Output 4: General purpose output or Channel A open-drain, active-Low, RxRDYAN/FFULLAN output. OP5 X O Output 5: General purpose output or Channel B open-drain, active-Low, RxRDYBN/FFULLBN output. OP6 X O Output 6: General purpose output or Channel A open-drain, active-Low, TxRDYAN output. OP7 X O Output 7: General purpose output, or Channel B open-drain, active-Low, TxRDYBN output.
IP0 X I Input 0: General purpose input or Channel A clear to send active-Low input (CTSAN). Pin has an
internal V
CC
pull-up device supplying 1 to 4 A of current.
IP1 X I Input 1: General purpose input or Channel B clear to send active-Low input (CTSBN). Pin has an
internal V
CC
pull-up device supplying 1 to 4 A of current.
IP2 X X I Input 2: General purpose input or counter/timer external clock input. Pin has an internal VCC pull-up
device supplying 1 to 4 A of current.
IP3 X I Input 3: General purpose input or Channel A transmitter external clock input (TxCA). When the
external clock is used by the transmitter, the transmitted data is clocked on the falling edge of the
clock. Pin has an internal V
CC
pull-up device supplying 1 to 4 A of current.
IP4 X I Input 4: General purpose input or Channel A receiver external clock input (RxCA). When the external
clock is used by the receiver, the received data is sampled on the rising edge of the clock. Pin has an
internal V
CC
pull-up device supplying 1 to 4 A of current.
IP5 X I Input 5: General purpose input or Channel B transmitter external clock input (TxCB). When the
external clock is used by the transmitter, the transmitted data is clocked on the falling edge of the
clock. Pin has an internal V
CC
pull-up device supplying 1 to 4 A of current.
IP6 X I Input 6: General purpose input or Channel B receiver external clock input (RxCB). When the external
clock is used by the receiver, the received data is sampled on the rising edge of the clock. Pin has an
internal V
CC
pull-up device supplying 1 to 4 A of current.
V
CC
X X I Power Supply: +5V supply input.
GND X X I Ground
Philips Semiconductors Product specification
SCC2692Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
6
DC ELECTRICAL CHARACTERISTICS
1, 2, 3
SYM-
LIMITS
BOL
PARAMETER
TEST CONDITIONS
Min Typ Max
UNIT
V
IL
Input low voltage 0.8 V
V
IH
Input high voltage (except X1/CLK)
6
2.0 V
V
IH
Input high voltage (except X1/CLK)
7
2.5 V
V
IH
Input high voltage (X1/CLK) 0.8 V
CC
V
V
OL
Output low voltage
I
OL
= 2.4mA
0.4 V
V
OH
Output high voltage (except OD outputs)
4
I
OH
= -400µA
V
CC
-0.5 V
I
IX1PD
X1/CLK input current - power down
V
IN
= 0 to V
CC
-10 +10 µA
I
ILX1
X1/CLK input low current - operating VIN = 0 -75 0 µA
I
IHX1
X1/CLK input high current - operating VIN = V
CC
0 75 µA
I
OHX2
X2 output high current - operating
V
OUT
= V
CC
, X1 = 0
0 +75 µA
I
OHX2S
X2 output high short circuit current - operating V
OUT
= 0, X1 = 0 -10 -1 mA
I
OLX2
X2 output low current - operating V
OUT
= 0, X1 = V
CC
-75 0 µA
I
OLX2S
X2 output low short circuit current - operating and power down V
OUT
= VCC, X1 = V
CC
1 10 mA
Input leakage current:
I
I
All except input port pins VIN = 0 to V
CC
-10 +10 µA
Input port pins VIN = 0 to V
CC
-20 +10 µA
I
OZH
Output off current high, 3-state data bus VIN = V
CC
10 µA
I
OZL
Output off current low , 3-state data bus VIN = 0V -10 µA
I
ODL
Open-drain output low current in off-state VIN = 0 -10 µA
I
ODH
Open-drain output high current in off-state VIN = V
CC
10 µA
Power supply current
5
I
CC
Operating mode CMOS input levels 10 mA Power down mode
8
CMOS input levels
2
10
A
NOTES:
1. Parameters are valid over specified temperature range.
2. All voltage measurements are referenced to ground (GND). For testing, all inputs swing between 0.4V and 2.4V with a transition time of 5ns maximum. For X1/CLK this swing is between 0.4V and 4.4V . All time measurements are referenced at input voltages of 0.8V and 2.0 V and output voltages of 0.8V and 2.0V , as appropriate.
3. Typical values are at +25°C, typical supply voltages, and typical processing parameters.
4. Test conditions for outputs: C
L
= 150pF, except interrupt outputs. T est conditions for interrupt outputs: CL = 50pF, R
L
= 2.7K to VCC.
5. All outputs are disconnected. Inputs are switching between CMOS levels of V
CC
-0.2V and VSS + 0.2V .
6. T
A
> 0°C
7. T
A
< 0°C
8. See UART application note for 5µA.
AC CHARACTERISTICS
1, 2, 4
LIMITS
SYMBOL
PARAMETER
Min Typ
3
Max
UNIT
Reset Timing (See Figure 3)
t
RES
RESET pulse width 200 ns
Bus Timing
5
(See Figure 4)
t
AS
A0-A3 setup time to RDN, WRN Low 10 ns
t
AH
A0-A3 hold time from RDN, WRN Low 100 ns
t
CS
CEN setup time to RDN, WRN Low 0 ns
t
CH
CEN hold time from RDN, WRN High 0 ns
t
RW
WRN, RDN pulse width 225 ns
t
DD
Data valid after RDN Low 175 ns
t
DA
RDN Low to data bus active
7
15 ns
t
DF
Data bus floating after RDN High 125 ns
t
DI
RDN High to data bus invalid
7
20 ns
t
DS
Data setup time before WRN High 100 ns
t
DH
Data hold time after WRN High 20 ns
t
RWD
High time between reads and/or writes
5, 6
200 ns
Philips Semiconductors Product specification
SCC2692Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
7
AC CHARACTERISTICS (Continued)
1, 2, 4
LIMITS
SYMBOL
PARAMETER
Min Typ
3
Max
UNIT
Port Timing5 (See Figure 5)
t
PS
Port input setup time before RDN Low 0 ns
t
PH
Port input hold time after RDN High 0 ns
t
PD
OPn output valid from WRN High 400 ns
Interrupt Timing (See Figure 6)
INTRN (or OP3-OP7 when used as interrupts) negated from:
Read RHR (RxRDY/FFULL interrupt) 300 ns Write THR (TxRDY interrupt) 300 ns
t
IR
9
Reset command (break change interrupt) 300 ns Stop C/T command (counter interrupt) 300 ns Read IPCR (input port change interrupt) 300 ns Write IMR (clear of interrupt mask bit) 300 ns
Clock Timing (See Figure 7)
t
CLK
X1/CLK High or Low time
100 ns
f
CLK
10
X1/CLK frequency 0 3.6864 4 MHz
t
CTC
CTCLK (IP2) High or Low time 100 ns
f
CTC
8
CTCLK (IP2) frequency 0 4 MHz
t
RX
RxC High or Low time 220 ns
f
RX
8
RxC frequency (16X) 0 2 MHz
(1X) 0 1 MHz
t
TX
TxC High or Low time 220 ns
f
TX
8
TxC frequency (16X) 0 1 MHz
(1X) 0 1 MHz
Transmitter Timing (See Figure 8)
t
TXD
TxD output delay from TxC external clock input on IP pin 350 ns
t
TCS
Output delay from TxC low at OP pin to TxD data output 0 150 ns
Receiver Timing (See Figure 9)
t
RXS
RxD data setup time before RxC high at external clock input on IP pin 240 ns
t
RXH
RxD data hold time after RxC high at external clock input on IP pin 200 ns
NOTES:
1. Parameters are valid over specified temperature range.
2. All voltage measurements are referenced to ground (GND). For testing, all inputs swing between 0.4V and 2.4V with a transition time of 5ns maximum. For X1/CLK this swing is between 0.4V and 4.4V . All time measurements are referenced at input voltages of 0.8V and 2.0 V and output voltages of 0.8V and 2.0V , as appropriate.
3. Typical values are at +25°C, typical supply voltages, and typical processing parameters.
4. Test conditions for outputs: C
L
= 150pF, except interrupt outputs. T est conditions for interrupt outputs: CL = 50pF, R
L
= 2.7K to VCC.
5. Timing is illustrated and referenced to the WRN and RDN inputs. The device may also be operated with CEN as the ‘strobing’ input. CEN and RDN (also CEN and WRN) are ORed internally. As a consequence, the signal asserted last initiates the cycle and the signal negated first terminates the cycle.
6. If CEN is used as the ‘strobing’ input, the parameter defines the minimum High times between one CEN and the next. The RDN signal must be negated for t
RWD
to guarantee that any status register changes are valid.
7. Guaranteed by characterization of sample units.
8. Minimum frequencies are not tested but are guaranteed by design.
9. 325ns maximum for T
A
> 70°C.
10.Operation to 0MHz is assured by design. Minimum test frequency is 2.0MHz. Crystal frequencies 2 to 4 MHz.
Philips Semiconductors Product specification
SCC2692Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
8
BLOCK DIAGRAM
The SCC2692 DUART consists of the following eight major sections: data bus buffer, operation control, interrupt control, timing, communications Channels A and B, input port and output port. Refer to the Block Diagram.
Data Bus Buffer
The data bus buffer provides the interface between the external and internal data buses. It is controlled by the operation control block to allow read and write operations to take place between the controlling CPU and the DUART.
Operation Control
The operation control logic receives operation commands from the CPU and generates appropriate signals to internal sections to control device operation. It contains address decoding and read and write circuits to permit communications with the microprocessor via the data bus buffer.
Interrupt Control
A single active-Low interrupt output (INTRN) is provided which is activated upon the occurrence of any of eight internal events. Associated with the interrupt system are the Interrupt Mask Register (IMR) and the Interrupt Status Register (ISR). The IMR can be programmed to select only certain conditions to cause INTRN to be asserted. The ISR can be read by the CPU to determine all currently active interrupting conditions.
Outputs OP3-OP7 can be programmed to provide discrete interrupt outputs for the transmitter, receivers, and counter/timer.
TIMING CIRCUITS Crystal Clock
The timing block consists of a crystal oscillator, a baud rate generator, a programmable 16-bit counter/timer, and four clock selectors. The crystal oscillator operates directly from a crystal connected across the X1/CLK and X2 inputs. If an external clock of the appropriate frequency is available, it may be connected to X1/CLK. The clock serves as the basic timing reference for the Baud Rate Generator (BRG), the counter/timer, and other internal circuits. A clock signal within the limits specified in the specifications section of this data sheet must always be supplied to the DUART.
If an external clock is used instead of a crystal, X1 should be driven using a configuration similar to the one in Figure 7.
BRG
The baud rate generator operates from the oscillator or external clock input and is capable of generating 23 commonly used data communications baud rates ranging from 50 to 130.4K baud. A
3.6864MHz crystal or external clock must be used to get the
standard baud rate. The clock outputs from the BRG are at 16X the actual baud rate. The counter/timer can be used as a timer to produce a 16X clock for any other baud rate by counting down the crystal clock or an external clock. The four clock selectors allow the independent selection, for each receiver and transmitter, of any of these baud rates or external timing signal.
Counter/Timer (C/T)
The counter timer is a 16 bit programmable divider that operates one of three modes: Counter, Timer or Time Out mode. In all three modes it uses the 16-bit value loaded to the CTUR and CTLR registers. (Counter timer upper and lower preset registers).
In the timer mode it generates a square wave.
In the counter mode it generates a time delay.
In the time out mode it monitors the receiver data flow and signals
data flow has paused. In the time out mode the receiver controls the starting/stopping of the C/T.
The counter operates as a down counter and sets its output bit in the ISR (Interrupt Status Register) each time it passes through 0. The output of the counter/timer may be seen on one of the OP pins or as an Rx or Tx clock.
The Timer/Counter is controlled with six (6) “commands”; Start C/T, Stop C/T, write C/T , preset registers, read C/T value, set or reset time out mode.
Please see the detail of the commands under the Counter/Timer register descriptions.
Communications Channels A and B
Each communications channel of the SCC2692 comprises a full-duplex asynchronous receiver/transmitter (UART). The operating frequency for each receiver and transmitter can be selected independently from the baud rate generator, the counter/timer , or from an external input.
The transmitter accepts parallel data from the CPU, converts it to a serial bit stream, inserts the appropriate start, stop, and optional parity bits and outputs a composite serial stream of data on the TxD output pin. The receiver accepts serial data on the RxD pin, converts this serial input to parallel format, checks for start bit, stop bit, parity bit (if any), or break condition and sends an assembled character to the CPU.
Input Port
The inputs to this unlatched 7-bit port can be read by the CPU by performing a read operation at address H’D’. A High input results in a logic 1 while a Low input results in a logic 0. D7 will always read as a logic 1. The pins of this port can also serve as auxiliary inputs to certain portions of the DUART logic.
Four change-of-state detectors are provided which are associated with inputs IP3, IP2, IP1 and IP0. A High-to-Low or Low-to-High transition of these inputs, lasting longer than 25 - 50µs, will set the corresponding bit in the input port change register. The bits are cleared when the register is read by the CPU. Any change-of-state can also be programmed to generate an interrupt to the CPU.
The input port pulse detection circuitry uses a 38.4KHz sampling clock derived from one of the baud rate generator taps. This results in a sampling period of slightly more than 25µs (this assumes that the clock input is 3.6864MHz). The detection circuitry, in order to guarantee that a true change in level has occurred, requires two successive samples at the new logic level be observed. As a consequence, the minimum duration of the signal change is 25µs if the transition occurs “coincident with the first sample pulse”. The 50µs time refers to the situation in which the change-of-state is “just missed” and the first change-of-state is not detected until 25µs later. All the IP pins have a small pull-up device that will source 1 to 4 A of current from V
CC
. These pins do not require pull-up devices or
V
CC
connections if they are not used.
Output Port
The output port pins may be controlled by the OPR, OPCR, MR and CR registers. Via appropriate programming they may be just another parallel port to external circuits, or they may represent many internal
Philips Semiconductors Product specification
SCC2692Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
9
conditions of the UART. When this 8-bit port is used as a general purpose output, the pins so defined will assume the compliment of the associated bit in the Output Port Register (OPR). OPR(n) = 1 results in OP(n) = Low and vice versa. Bits of the OPR can be individually set and reset. A bit is set by performing a write operation at address H’E’ with the accompanying data specifying the bits to be reset (1 = set, 0 = no change). Likewise, a bit is reset by a write at address H’F’ with the accompanying data specifying the bits to be reset (1 = reset, 0 = no change).
Outputs can be also individually assigned specific functions by appropriate programming of the Channel A mode registers (MR1A, MR2A), the Channel B mode registers (MR1B, MR2B), and the Output Port Configuration Register (OPCR).
Output ports are driven high on hardware reset. Please note that these pins drive both high and low. HOWEVER when they are programmed to represent interrupt type functions (such as receiver ready, transmitter ready or counter/timer ready) they will be switched to an open drain configuration in which case an external pull-up device would be required.
OPERATION Transmitter
The SCC2692 is conditioned to transmit data when the transmitter is enabled through the command register. The SCC2692 indicates to the CPU that it is ready to accept a character by setting the TxRDY bit in the status register. This condition can be programmed to generate an interrupt request at OP6 or OP7 and INTRN. When a character is loaded into the Transmit Holding Register (THR), the above conditions are negated. Data is transferred from the holding register to transmit shift register when it is idle or has completed transmission of the previous character. The TxRDY conditions are then asserted again which means one full character time of buffering is provided. Characters cannot be loaded into the THR while the transmitter is disabled.
The transmitter converts the parallel data from the CPU to a serial bit stream on the TxD output pin. It automatically sends a start bit followed by the programmed number of data bits, an optional parity bit, and the programmed number of stop bits. The least significant bit is sent first. Following the transmission of the stop bits, if a new character is not available in the THR, the TxD output remains High and the TxEMT bit in the Status Register (SR) will be set to 1. Transmission resumes and the TxEMT bit is cleared when the CPU loads a new character into the THR.
If the transmitter is disabled, it continues operating until the character currently being transmitted is completely sent out. The transmitter can be forced to send a continuous Low condition by issuing a send break command.
The transmitter can be reset through a software command. If it is reset, operation ceases immediately and the transmitter must be enabled through the command register before resuming operation. If CTS operation is enable, the CTSN input must be Low in order for the character to be transmitted. If it goes High in the middle of a transmission, the character in the shift register is transmitted and TxDA then remains in the marking state until CTSN goes Low. The transmitter can also control the deactivation of the RTSN output. If programmed, the RTSN output will be reset one bit time after the character in the transmit shift register and transmit holding register
(if any) are completely transmitted, if the transmitter has been disabled.
Receiver
The SCC2692 is conditioned to receive data when enabled through the command register. The receiver looks for a High-to-Low (mark-to-space) transition of the start bit on the RxD input pin. If a transition is detected, the state of the RxD pin is sampled each 16X clock for 7-1/2 clocks (16X clock mode) or at the next rising edge of the bit time clock (1X clock mode). If RxD is sampled High, the start bit is invalid and the search for a valid start bit begins again. If RxD is still Low, a valid start bit is assumed and the receiver continues to sample the input at one bit time intervals at the theoretical center of the bit, until the proper number of data bits and parity bit (if any) have been assembled, and one stop bit has been detected. The least significant bit is received first. The data is then transferred to the Receive Holding Register (RHR) and the RxRDY bit in the SR is set to a 1. This condition can be programmed to generate an interrupt at OP4 or OP5 and INTRN. If the character length is less than 8 bits, the most significant unused bits in the RHR are set to zero.
After the stop bit is detected, the receiver will immediately look for the next start bit. However, if a non-zero character was received without a stop bit (framing error) and RxD remains Low for one half of the bit period after the stop bit was sampled, then the receiver operates as if a new start bit transition had been detected at that point (one-half bit time after the stop bit was sampled).
The parity error, framing error, and overrun error (if any) are strobed into the SR at the received character boundary, before the RxRDY status bit is set. If a break condition is detected (RxD is Low for the entire character including the stop bit), a character consisting of all zeros will be loaded into the RHR and the received break bit in the SR is set to 1. The RxD input must return to high for two (2) clock edges of the X1 crystal clock for the receiver to recognize the end of the break condition and begin the search for a start bit. This will
usually require a high time of one X1 clock period or 3 X1 edges since the clock of the controller is not synchronous to the X1 clock.
Receiver FIFO
The RHR consists of a First-In-First-Out (FIFO) stack with a capacity of three characters. Data is loaded from the receive shift register into the topmost empty position of the FIFO. The RxRDY bit in the status register is set whenever one or more characters are available to be read, and a FFULL status bit is set if all three stack positions are filled with data. Either of these bits can be selected to cause an interrupt. A read of the RHR outputs the data at the top of the FIFO. After the read cycle, the data FIFO and its associated status bits (see below) are ‘popped’ thus emptying a FIFO position for new data.
Receiver Status Bits
In addition to the data word, three status bits (parity error, framing error, and received break) are also appended to each data character in the FIFO (overrun is not). Status can be provided in two ways, as programmed by the error mode control bit in the mode register. In the ‘character’ mode, status is provided on a character-by-character basis; the status applies only to the character at the top of the FIFO. In the ‘block’ mode, the status provided in the SR for these three bits is the logical-OR of the status for all characters coming to the top of the FIFO since the last ‘reset error’ command was issued. In either
Loading...
+ 21 hidden pages