Philips VRX222AT User Manual

VCR PLUS+™PROGRAMMING Simplifies VCR programming by allowing you to merely enter PlusCode

programming numbers found in

many published television listings CLOCK/FUNCTION DISPLAY Alerts

the user to all important recording and playback conditions, correct time, counter position, tape speed, and channel number

DIGITAL AUTO TRACKING SYSTEM Automatically seeks the optimum tracking position and optimum audio signal for clearest picture and sound

ONE-TOUCH RECORD Record up to eight hours or to the end of the tape with the touch of a single button. Each touch of the OTR button adds 30 minutes of additional recording time

FULL AUTO-FEATURE PACKAGE

• Power On

• Digital Auto Tracking

• Auto Play

• Auto Repeat

• Auto Rewind

• Auto Eject

• Auto Power Off

VIDEOCASSETTE RECORDER WITH VCR PLUS+™ PROGRAMMING

VRX222AT

Multifunction Infrared Remote

Recorder

Videocassette

• Power On

• Digital Auto Tracking

• Auto Play

• Auto Repeat

• Auto Rewind

• Auto Eject

• Auto Power Off

INTERNET ADDRESS: http://www.philipsmagnavox.com

additional features:

Videocassette Recorder with VCR Plus

Programming

VRX222AT

UPC: 037849848432 Product Dimensions: 14.2"W x 3.6"H x 9.2"D Product Weight: 5.94 lbs. Carton Dimensions: 16.8"W x 6.4"H x 12.2"D Carton Weight: 8.1 lbs. Master Pack: 1

Contains: Two-Head Videocassette Recorder, Multifunction Remote Control w/Batteries, RF Coaxial Cable, Operating Instructions, Warranty Information

Printed in U.S.A. ©1997 Philips Consumer Electronics Co. A Division of Philips Electronics North America Corp. Specifications subject to change without notice. Visual Communications, Philips Consumer Electronics Co.

VCR Plus+ and PlusCode are trademarks of Gemstar Development Corporation. The VCR Plus+ system is manufactured under license from Gemstar Development Corporation.

AUTOMATIC CHANNEL SETUP Activating this

feature allows the VCR tuner to scan through television frequencies, automatically storing active broadcast channels into memory.Then, only active channels programmed into memory are tuned, using the channel up/down buttons on either the remote or front panel of the VCR. Automatic channel preset can be repeated whenever desired, should new channels become available. Channels can be manually added or deleted.

181-CHANNEL FS TUNING The digital quartz

tuner is capable of receiving up to 181 channels, including UHF, VHF, and 113 cable channels, without the inconvenience and expense of a cable company decoder/converter (on non-scrambled cable systems). Channel tuning is by random access with the remote control transmitter or scan tuning up and down by remote or at the set.

CLOCK/FUNCTION DISPLAY Continuously alerts

the user to all important recording and playback conditions, correct time, counter position, tape speed, channel number, etc. When the VCR is turned off, the time display automatically dims, to make it less distracting.

BILINGUAL (ENGLISH/SPANISH) ON-SCREEN FUNCTION DISPLAY Indicates record/playback

functions, channel number, clock setting, date, counter, programming, one-touch record, and record standby, keeping the user alerted to the status of all features in a heads up, on-screen display.

ON-SCREEN, REAL-TIME COUNTER Unlike the

0000 to 9999 tape counters found in standard VCRs, this unit incorporates a linear, real-time counter which shows elapsed recording and/or playback time in hours, minutes, and seconds.

TIMER/PROGRAMMER BACKUP SYSTEM Retains

timer programming information for up to one full minute in the event of momentary power interruptions.

convenience:

REPEAT PLAY When the VCR recognizes no

recorded signal or reaches the end of a tape with the Repeat Play control activated, it will automatically rewind to the beginning and enter the Play mode again. Repeat Play can be discontinued by touching the button a second time or by changing operation mode.

QUICK START MECHANISM Quickly and

effortlessly switches the tape mechanism from Stop to Play in only one second, instead of the approximately 5 1/4 seconds of older models.

AUDIO/VIDEO INPUT/OUTPUT JACKS Connect

your VCR to the direct audio and video inputs of a television receiver or monitor equipped with input jacks, for better picture and sound quality during tape playback. Jacks also allow a second VCR to be connected for editing and/or duplicating personally recorded, non-copyrighted videotapes.

15X FORWARD/REVERSE LATCHING SEARCH

Search in forward or reverse mode at 15 times normal playing speed in SLP, and 5 times normal in SP. The Latching Search feature provides continuous forward or reverse search with a single touch of the control. A second touch stops the search operation and returns the unit to the Play mode.

MULTIFUNCTION INFRARED REMOTE Controls

all operating features and functions of this VCR with armchair convenience–including all special features, random channel access, and channel scan up/down, providing an LED virtual “handshake” for confirmation.

VCR PLUS+™ PROGRAMMING Simplifies

VCR programming by allowing you to simply enter PlusCode®programming numbers found in many published television listings. When recording begins, your VCR automatically selects the proper TV channel and program length. Backup memory logic retains the cable channel guide map indefinitely, even during a power failure or when the VCR is disconnected from its power source.

ONE-TOUCH RECORD Record up to eight

hours or to the end of the tape with the touch of a single button. Each touch of the OTR button adds 30 minutes of additional recording time.

8-EVENT/1 YEAR SMART PROGRAMMING

Program your VCR for unattended recording of up to eight separate programs over a full 365-day period. No manual setting, adjusting, or programming of the calendar function is required.

REMOTE CONTROL ON-SCREEN MENU PROGRAMMING Program by remote control

for unattended recording, with programming instructions on-screen for visual verification. On-screen menus lead you through normal, daily, or weekly programming by program number, channel to be recorded, start and stop times, speed, and date of recording by day, month, and year. Pushing the CLEAR button allows you to go back and reprogram over mistakes, and pushing the MENU button at the end of programming verifies that instructions are locked into memory.

DIGITAL AUTO TRACKING SYSTEM When

tape playback begins, this feature automatically seeks the optimum tracking position in the tracking range, and the optimum audio signal tracking position for clearest picture and sound from videotapes. Controls are provided on the remote transmitter to give you manual control should tracking adjustments be necessary.

picture:

programming & record/playback features:

remote control:

special effects: