Philips VRA999PH User Manual
Video Cassette Recorder
VRA999
Owner’s Manual
Important!
Return your Warranty Registration
Card within 10 days. See why inside.
Warranty
Verification
Registering your product within
10 days confirms your right to
maximum protection under the
terms and conditions of your
PHILIPS warranty.
Owner
Confirmation
Your completed Warranty
Registration Card serves as
verification of ownership in the
event of product theft or loss.
Model
Registration
Returning your Warranty
Registration Card right away
guarantees you’ll receive all
the information and special
offers which you qualify for as the
owner of your model.
Once your PHILIPS purchase is registered, you’re eligible to receive all the privileges of owning a
PHILIPS product. So complete and return the Warranty Registration Card enclosed with your
purchase at once. And take advantage of these important benefits.
Return your Warranty Registration card today to
ensure you receive all the
benefits
you’re entitled to.
For Customer Use
Enter below the Serial No.
which is located on the rear
of the cabinet. Retain this
information for future
reference.
Model No. ______________
Serial No. ______________
Congratulations on your purchase, and
welcome to the “family!”
Dear PHILIPS product owner:
Thank you for your confidence in PHILIPS. You’ve selected one of
the best-built, best-backed products available today. And we’ll do
everything in our power to keep you happy with your purchase
for many years to come.
As a member of the PHILIPS “family,” you’re entitled to protection
by one of the most comprehensive warranties and outstanding
service networks in the industry.
What’s more, your purchase guarantees you’ll receive all the
information and special offers for which you qualify, plus easy
access to accessories from our convenient home shopping
network.
And most importantly you can count on our uncompromising
commitment to your total satisfaction.
All of this is our way of saying welcome-and thanks for investing in
a PHILIPS product.
Sincerely,
Robert Minkhorst
President and Chief Executive Officer
P.S. Remember, to get the most from your PHILIPS
product, you must return your Warranty Registration
Card within 10 days. So please mail it to us right now!
Know these
safetysymbols
This “bolt of lightning” indicates
uninsulated material within
your unit may cause an electrical shock.
For the safety of everyone in your
household, please do not remove
product covering.
The “exclamation point” calls
attention to features for which
you should read the enclosed literature
closely to prevent operating and
maintenance problems.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN
OR MOISTURE.
CAUTION: To prevent electric
shock, match wide blade of plug to
wide slot, and fully insert.
ATTENTION: Pour éviter les choc
électriques, introduire la lame la plus
large de la fiche dans la borne
correspondante de la prise et pousser
jusqu’au fond.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
R
E
G
I
S
T
R
A
T
I
O
N
N
E
E
D
E
D
W
I
T
H
I
N
1
0
D
A
Y
S
Hurry!
Visit our World Wide Web Site at http://www.philipsusa.com
Introduction 3
Features
• Automatic Channel Setup
• Automatic Clock Setting
• Automatic Head Cleaner
• Battery Backup
• Blue Background
• Child Lock
• Daylight-Savings Time
• Hi-Fi Stereo Tape Playback
• Index Search
• Multi-Channel Television Sound (MTS) System
• 19 Micron Head, provides a better picture when you view tapes
recorded in slow speed (SLP)
• On-Screen Menus in English, Spanish, or French
• Quick Programming
• Remote Control with Capability to Operate TV, Cable Box, and
Direct Broadcast System (DBS)
• Repeat Play
• S-VHS ET
• S-VHS Recording
• SmartClock
TM
• SmartPicture
TM
• VCR Plus+ Programming System
• Video Stabilizer
Safety Precautions
Warning: To prevent fire or shock hazard, do not expose
this equipment to rain or moisture.
Federal Communications Commission (FCC) Warning: Any
unauthorized changes or modifications to this equipment
void the user’s authority to operate it.
This VCR, equipped with a High Quality (HQ) System, is compatible
with existing Video Home System (VHS) equipment. Philips
Consumer Electronics recommends that you use only video cassette
tapes that are labelled with the mark or the S-VHS mark. The
use of other tapes may result in poor picture quality and excessive
deposits on the video heads, which may not be covered by the
warranty if damage occurs. The S-VHS feature provides the best
picture quality when the VCR uses S-VHS tapes.
Note to the Cable TV System Installer: This reminder is provided to
call the Cable TV system installer’s attention to Article 820-40 of the
National Electrical Code, which provides guidelines for proper
grounding – in particular, specifying that the cable ground shall be
connected to the grounding system of the building, as close to the
point of cable entry as possible.
Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.
Welcome to your VCR owner’s manual.
This manual has seven sections: Setting Up Your VCR; Description of Controls; Basic Operations;
Recording; Playing; Additional Features; and Information You May Need. The instructions explain all of the
VCR’s features, which are listed below.
The ENERGY STAR®name and logo are registered marks of the U.S.
Environmental Protection Agency. As an ENERGY STAR®Partner,
Philips Consumer Electronics has determined that this product meets
the ENERGY STAR®guidelines for energy efficiency.
Copyright 1999 Philips Consumer Electronics. All rights reserved. SmartPicture and
SmartClock are trademarks of Philips Consumer Electronics.
VCR Plus+C3and PlusCode are registered trademarks of Gemstar Development
Corporation. The VCR Plus+ system is manufactured under license from Gemstar
Development Corporation.
• Your new product, its packaging, and
this manual contain materials that can
be recycled and reused. Specialized
companies can recycle your product to
increase the amount of reusable
materials and to minimize the
amount that needs to be properly
disposed.
Your product uses batteries that
should not be thrown away when
depleted but should be disposed of as
small chemical waste. Please find out
about the local regulations on disposal
of your old products, batteries,
manual, and packaging whenever you
replace existing equipment.
Helpful Hints
4 Table of Contents
Setting Up Your VCR
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Before Using Your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Hookups without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7
Hookups with a Cable Box/Direct Broadcast System . . . . . . . . . . . . . . . . . . . . . . . . .8-9
Installing/Removing the Lithium Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Turning on Your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-12
Automatic Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-14
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-19
Daylight-Savings Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Description of Controls
Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-23
Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
On-Screen Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Setting the Remote Control to Operate a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Setting the Remote Control to Operate a Cable Box/DBS . . . . . . . . . . . . . . . . . . . . .29
Basic Operations
Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Recording
S-VHS Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
S-VHS ET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
One-Touch Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Recording One Channel/Watching Another . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Setting Up the VCR Plus+ Programming System . . . . . . . . . . . . . . . . . . . . . . . . . . .36-37
Timer Recording with the VCR Plus+ Programming System . . . . . . . . . . . . . . . . . .38-39
Quick Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-43
Timer Recording Speed Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Connecting the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Setting the Controller to Operate a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . .46-47
Setting the Controller to Operate a DBS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48-49
Rerecording (Tape Duplication) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Playing
Index Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Multi-Channel Television Sound System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52-53
Hi-Fi Stereo Tape Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Video Stabilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
SmartPicture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Playback Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57-58
Additional Features
Child Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Blue Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Automatic Operation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Information You May Need
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64-65
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Before Using Your VCR 5
Putting Batteries in the Remote Control
Using the Remote Control
3
Replace the battery compartment lid.
2
To record again, cover the hole with cellophane tape.
•Do not put objects between the remote control and the VCR.
•Point the remote control at the VCR’s remote sensor, then press
the VCR button before pressing other VCR operation buttons.
•Point the remote control at the TV, then press the TV button
before pressing other TV operation buttons.
•Point the remote control at the Cable Box/DBS, then press the
CBL/DBS button before pressing other Cable Box/DBS operation
buttons.
• The remote control and its batteries
are supplied.
• Do not mix alkaline and manganese
batteries.
• Do not mix old and new batteries.
Helpful Hints
VCR Maintenance
•Remove any light adhesive stick-on notes from the video cassette
before putting the cassette in the VCR. Removable labels can jam
the VCR.
•Periodic maintenance is required to maintain your VCR’s
performance. Your VCR has an automatic head cleaner, but the
video heads eventually will require cleaning or replacement. Only
an authorized service center should perform this service.
Erase Protection
Video cassettes have record tabs to ensure that recordings are
not erased accidentally.
1
To prevent accidental erasure, break off the tab with a
screwdriver.
1
To remove the battery compartment lid, push in the tab,
then pull up the lid.
2
Place two AA batteries inside the battery compartment
with their +and – ends aligned as indicated.
1
2
Removing the Plastic Cover from the Front Panel
A thin, plastic cover may protect the front panel of your VCR.
Before using the VCR, lift a corner of the plastic, then peel it off.
1
2
6 Hookups without a Cable Box
ANT. IN
VIDEO
L
R
AUDIO
(MONO)
RF OUT
CH3
CH4
CABLE
BOX
LP
30561-003
OUTIN
S-VIDEO
OUTIN
OR
ANT. IN
RF OUT
75Ω
ANT /
CABLE
OR
75Ω
ANT /
CABLE
The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or
a Direct Broadcast System, please refer to pages 8-9. After you hook up the VCR and install the lithium
battery, please go to page 11 to turn on the VCR.
ANTENNA IN
Jack
(on back of TV)
Cable
(75 ohm)
Antenna
Indoor/Outdoor
(300 ohm)
1
Disconnect the antenna or cable from your TV.
2
Connect the antenna or cable to the ANT(enna) IN Jack on the back of the
VCR.
Cable
(75 ohm)
Antenna
Indoor/Outdoor
(300 ohm)
Hookups without a Cable Box (cont’d) 7
ANT. IN
VIDEO
L
R
AUDIO
(MONO)
OUT
IN
OUTIN
RF OUT
CH3
CH4
S-VIDEO
CABLE
BOX
LP
30561-003
CH 4
or
CH 3
CH3 / CH4
Switch
CH3
CH4
CH3
CH4
ANT. IN
VIDEO
L
R
AUDIO
(MONO)
RF OUT
CH3
CH4
CABLE
BOX
LP
30561-003
OUTIN
S-VIDEO
OUTIN
75V
ANT /
CABLE
75Ω
ANT /
CABLE
ANT. IN
RF OUT
RF coaxial cable
Antenna
or Cable
3
Connect the RF coaxial cable (supplied) to the RF OUT Jack on the back of
the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on
type or screw-on type of coaxial cable, whichever you prefer. A snap-on type is
supplied.)
5
Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever
channel is not used or least used in your area. To operate your VCR with your TV, set
the TV to the same channel. For example, when playing a tape, if the CH3/CH4
switch is set to CH3, the TV should be on channel 3.
Antenna In Jack
(on back of TV)
example only
4
Plug in the TV and the VCR.
6
You are ready to turn on the VCR. Please go to page 11 before turning on the
VCR.
ANT. IN
VIDEO
L
R
AUDIO
(MONO)
OUT IN
OUTIN
RF OUT
CH3
CH4
S-VIDEO
CABLE
BOX
LP
30561-003
75Ω
ANT /
CABLE
OUT
IN
8 Hookups with a Cable Box/Direct Broadcast System
Connections
1
Connect a Cable signal to the IN jack on the Cable Box/DBS.
2
Use an RF coaxial cable (supplied) to connect the OUT jack on
the Cable Box/DBS to the ANT(enna) IN jack on the VCR.
3
Use a second RF coaxial cable to connect the RF OUT jack on the
VCR to the TV’s ANTENNA INjack.
Recording/Viewing Any Channel
1
With the VCR on and in VCR position (the VCR light will appear
on the display panel), use the CH(annel) 8/9 button to set the
VCR to the Cable Box/DBS output channel (channel 03 or 04).
2
Set the TV to the same channel to which you set the VCR. Set the
CH3/CH4 switch on the VCR to the same channel.
3
Select the channel you want to view/record at the Cable
Box/DBS.
1
2
There are two ways to connect your Cable Box/DBS to the VCR. With this connection:
• You may view any channel.
• You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR.
• You may not view a channel other than the one you are recording.
• You may not set up channels at the VCR.
• Timer recordings are programmed differently. Set the TV and the VCR to the Cable Box/DBS output
channel (channel 03 or 04); set the VCR’s CH3/CH4 switch to the same channel.
If you are not using the Controller, set your Cable Box/DBS to the channel you want to record. When you
enter the channel you want to record in a timer recording, select the Cable Box/DBS output channel (03 or
04). This is step 3 on page 40.
If you are using the Controller, enter the channel that you want to record at step 3 on page 40 (not the
Cable Box/DBS output channel). The Controller will select the channel at the Cable Box/DBS for recording.
3
Cable signal
RF coaxial cable
RF coaxial
cable
Cable Box/DBS
VCR
TV’s
ANTENNA
IN jack
Hookups with a Cable Box/Direct Broadcast System (cont’d) 9
ANT. IN
VIDEO
L
R
AUDIO
(MONO)
OUT IN
OUTIN
RF OUT
CH3
CH4
S-VIDEO
CABLE
BOX
LP
30561-003
IN
OUT
75Ω
ANT /
CABLE
Connections
1
Connect a Cable signal to the VCR’s ANT(enna) IN jack.
2
Use an RF coaxial cable (supplied) to connect the RF OUT jack on
the VCR to the IN jack on the Cable Box/DBS.
3
Use a second RF coaxial cable to connect the OUT jack on the
Cable Box/DBS to the TV’s ANTENNA INjack.
Recording One Channel/Watching Another
1
Put the Cable Box/DBS on the same channel as the VCR’s
CH3/CH4 switch. Set the TV to the Cable Box/DBS output
channel (03 or 04).
Then, with the VCR in VCR position (the VCR light will appear on
the display panel), use the CH(annel) 8/9 button to select the
channel you want to record at the VCR. Start the recording.
2
Press the VCR/TV button once to put the VCR in TV position.
(The VCR light will disappear.)
3
Select the channel you want to watch at the Cable Box/DBS.
1
2
With this connection:
• You may watch one channel while recording another.
• You may not record scrambled channels.
3
Cable signal
RF coaxial
cable
RF coaxial cable
VCR
Cable Box/DBS
TV’s
ANTENNA
IN jack
• When you play a tape, make sure
the Cable Box/DBS is set to the
same channel as the CH3/CH4
switch on the VCR. Set the TV to
the Cable Box/DBS output channel
(03 or 04).
Helpful Hint
10 Installing/Removing the Lithium Battery
You may install a lithium battery in the VCR. This will allow the
VCR to save the clock setting and the programmed timer
recordings if a power outage occurs. The battery can back up
your timer recordings and clock setting for around six months
(4,000 hours).
Connect the power plug to an AC outlet before installing the
1
Connect the power plug to an AC outlet and turn off the
VCR power.
2
To open the battery compartment, press the cover’s
release tab to the left, then remove the cover.
3
Press a lithium battery into the compartment with the
plus (+)side facing out.
To remove the lithium battery, push the latch A downward using
a pointed, non-metallic object.
4
Replace the battery compartment cover.
Lithium Battery Warning
The lithium battery may present a fire or chemical burn hazard if
mistreated.
CAUTION: Risk of fire, explosion, and burns. Do not recharge,
disassemble, heat above 100°C, or incinerate.
Replace the battery with a Panasonic (Matsushita Electric), Sanyo,
Sony, or Maxell CR2025 only; use of another battery may present
a risk of fire or explosion. To order a new battery, see page 68
(back cover).
• Promptly dispose of used batteries.
• Keep the battery away from children.
• Do not dispose of the battery in a fire.
2
3
4
A
3
4
1
Turning on Your VCR 11
• Before turning on your VCR, make sure there are batteries in
the remote control and the VCR, TV, and Cable Box/DBS (if
applicable) are connected.
• The menus will continue to appear every time you turn on the
VCR until you complete the steps on pages 11-12.
• If you want to set up the Controller now, you must first
connect the Controller. See page 45.
• Leave the Cable Box turned on if you plan to set up the Cable
Box Controller now.
• If you plan to set up the Controller now, set the Cable Box to a
channel other than channel 09.
1
Press the VCR button, then press the POWER button.
2
Turn on the TV. Set it to channel 3 or 4, whichever the
CH3/CH4 switch on the back of the VCR is set to. The
menu shown below will appear.
3
Press the PLAY 8 button or the STOP 9 button to select
the on-screen display language.
2
Turn on the TV.
4
Press the FF :/OK button. The menu shown below will
appear.
SELECT , 9
A ENGLISH
ESPAÑOL
FRANÇAIS
MAKE SELECTION OR
PUSH :/OK TO CONTINUE
CABLE BOX CONTROLLER
OFF
A OFF CH.=CHANNEL
ON CH. 2 ON CH. 7
ON CH. 3 ON CH. 8
ON CH. 4 ON CH. 9
ON CH. 5 ON A/V FRONT
ON CH. 6 ON A/V REAR
SELECT , 9 CHOOSE :/OK
TO END PUSH EXIT
Instructions continue on page 12.
VCRTV
VCR/TV
QUICK PROGRAMMING
POWER
STILL/SLOW
EJECT
CHVOL
EXIT/STATUS
TIMER
JOG/SHTL
SMARTPICTURE
INDEX AUDIO/MUTE
MENU
-
+
CBL / DBS
1 2 3
4 5 6
7 8 9
START STOP DATE
DBS DAILY
PLAY
REW FF
/OK
STOP
WEEKLY
REV
/OTR
RECREC
FWD
-
+-+
SPEED
0
CLEAR
5-6
12 Turning on Your VCR (cont’d)
6
Press the FF :/OK button to begin automatic channel setup.
AUTO CH. SET PROCEEDING PLEASE WAIT will appear on the
screen. The VCR will memorize all of the channels you receive, so
when you scan through channels using the CH(annel) 8/9 button,
you’ll only scan through channels that you receive.
7
When channels are set up, AUTO CH. SET COMPLETED will
appear on the screen briefly.
CONNECT ANTENNA OR CABLE
TO VCR
THEN PUSH :/OK KEY
OR . . .
FOR PLAY ONLY – PUSH STOP
• Auto or – – : – – may appear on
the display panel until the clock is
set. After you connect the
antenna/cable signal to the VCR
and connect the VCR to a power
source, the clock may set itself
automatically. The current time may
appear on the VCR display panel.
• If you do not want to set up
channels now, press the STOP 9
button at step 6. TUNER NOT SET
will appear on the screen briefly.
• You may not set up channels at
step 6 if you are using a Cable
Box/DBS.
Helpful Hints
5
If you do not want to set up the Cable Box Controller
now, press the FF :/OK button to leave the Controller
turned OFF. The display shown below will appear on the
screen. Proceed to step 6. You may set up the Controller later
by following the instructions on pages 45-49.
If you do want to set up the Cable Box Controller now,
follow steps 5-8 on pages 46-47.
7
Wait for the VCR to set up
channels.
CBL / DBS
VCR/TV
1 2 3
START STOP DATE
4 5 6
DBS DAILY
7 8 9
SPEED
-
REW FF
SMARTPICTURE
JOG/SHTL
REV
POWER
QUICK PROGRAMMING
+
-+-
0
STILL/SLOW
PLAY
STOP
MENU
EXIT/STATUS
TIMER
INDEX AUDIO/MUTE
VCRTV
EJECT
WEEKLY
CLEAR
+
/OK
CHVOL
RECREC
/OTR
FWD
Automatic Channel Setup 13
5
Wait for the VCR to set up
channels.
2-4
1
Although your VCR may automatically memorize the channels you
receive when you turn it on for the first time, this function lets you
set up channels again. Make each entry within one minute of the
previous entry.
5
Wait for a few minutes while the VCR sets up channels.
When programming is complete, AUTO CH. SET COMPLETED will
appear on the screen. Then, the programming of the lowest channel
number placed in the VCR’s memory will appear on the screen.
Now when you press the CH(annel) 8/9 button, you will scan only
through channels you receive.
1
Press the VCR button, then press the MENU button.
2
Press the PLAY 8 or STOP 9 button to select TUNER
SET UP, then press the FF :/OK button.
3
Press the FF :/OK button repeatedly so that ANT (if you
have an antenna) or CABLE (if you have a cable
connection) appears beside CABLE/ANTENNA.
4
Press the STOP 9 button to select AUTO CH.
PROGRAMMING, then press the FF :/OK button. AUTO
CH. SET PROCEEDING PLEASE WAIT and a scale that shows the
progress of channel setup will appear on the screen. The VCR will
memorize all the channels you receive.
• The two Line Input modes will always
be stored in the VCR’s memory at
channel 00. To select A/V IN FRONT
or A/V IN REAR, press 0, then press
the CH(annel) 8/9 button so that LF appears on the display panel (for
A/V IN FRONT) or
L-I appears on the display panel (for
A/V IN REAR). To exit Line Input
mode, use the CH(annel) 8/9 button
to select a channel other than 0.
Helpful Hints
SELECT , 9 CHOOSE :/OK
A CABLE/ANTENNA CABLE
AUTO CH. PROGRAMMING
ADD/DELETE CH.
TO END PUSH EXIT
SELECT , 9 CHOOSE :/OK
A VCR SET UP
TUNER SET UP
INITIAL SET UP
TO END PUSH EXIT
SELECT , 9 CHOOSE :/OK
A CABLE/ANTENNA ANT
AUTO CH. PROGRAMMING
ADD/DELETE CH.
TO END PUSH EXIT
SELECT , 9 CHOOSE :/OK
CABLE/ANTENNA ANT
A AUTO CH. PROGRAMMING
ADD/DELETE CH.
TO END PUSH EXIT
AUTO CH. SET PROCEEDING
PLEASE WAIT
START FINISH
L L L L L L L L L L L L
• • • • • • • • •
VCRTV
VCR/TV
QUICK PROGRAMMING
POWER
STILL/SLOW
EJECT
CHVOL
EXIT/STATUS
TIMER
JOG/SHTL
SMARTPICTURE
INDEX AUDIO/MUTE
MENU
-
+
CBL / DBS
1 2 3
4 5 6
7 8 9
START STOP DATE
DBS DAILY
PLAY
REW FF
/OK
STOP
WEEKLY
REV
/OTR
RECREC
FWD
-
+-+
SPEED
0
CLEAR
14 Automatic Channel Setup (cont’d)
Adding/Deleting Channels
2
Press the PLAY 8 or STOP 9 button to select TUNER
SET UP, then press the FF :/OK button.
3
Press the PLAY 8 or STOP 9 button to select
ADD/DELETE CH., then press the FF :/OK button.
4
Use the Number buttons, the CH(annel) 8/9 button, or
the PLAY 8 or STOP 9 buttons to select the channel
you want to add or delete. An arrow will appear beside the
selected channel.
5
Press the FF :/OK button so that DELETED or ADDED
appears beside the channel number. Repeat steps 4-5 to add
or delete all the channels you wish.
6
Press the EXIT/STATUS button. Programming of the last
channel you selected will appear on the screen.
1
Press the VCR button, then press the MENU button.
SELECT , 9 CHOOSE :/OK
A CABLE/ANTENNA CABLE
AUTO CH. PROGRAMMING
ADD/DELETE CH.
TO END PUSH EXIT
SELECT , 9
124 DELETED
125 DELETED
01
– – – –
> DELETED
02 ADDED
03 ADDED
TO ADD/DELETE PUSH :/OK
TO END PUSH EXIT
SELECT , 9 CHOOSE :/OK
A VCR SET UP
TUNER SET UP
INITIAL SET UP
TO END PUSH EXIT
2-5
6
1
4
1
VCRTV
VCR/TV
QUICK PROGRAMMING
POWER
STILL/SLOW
EJECT
CHVOL
EXIT/STATUS
TIMER
JOG/SHTL
SMARTPICTURE
INDEX AUDIO/MUTE
MENU
-
+
CBL / DBS
1 2 3
4 5 6
7 8 9
START STOP DATE
DBS DAILY
PLAY
REW FF
/OK
STOP
WEEKLY
REV
/OTR
RECREC
FWD
-
+-+
SPEED
0
CLEAR
Setting the Clock 15
• To program the VCR so its clock
will automatically move forward one
hour in April and turn back one
hour in October, see page 20.
• To make corrections, follow steps
1-3, then press the FF :/OK button
until the item you want to correct is
flashing. Press the PLAY 8 or
STOP 9 button to enter the correct
information. Press the EXIT/STATUS
button.
Helpful Hints
There are four ways to set the VCR’s clock: Manually, with Time
Zone Selection, with Manual PBS Channel Selection, or with
Automatic PBS Channel Selection. Cable Box/DBS users must set
the clock manually. Before you set the clock, make sure:
• The VCR power is on.
• The VCR light appears on the display panel. If it does not, press
the VCR/TV button once.
• Channels are set up.
• You make each entry within one minute of the previous entry.
To set the clock manually, follow the steps on pages 15-16. To use
Time Zone Selection, go to page 17. To use Manual PBS Channel
Selection, go to page 18. To use Automatic PBS Channel Selection,
go to page 19.
Manual Clock Setting
1
Press the VCR button, then press the MENU button.
3
Press the PLAY 8 or STOP 9 button to select CLOCK,
then press the FF :/OK button. CABLE BOX USERS SET
CLOCK MANUALLY will appear briefly.
2
Press the PLAY 8 or STOP 9 button to select INITIAL
SET UP, then press the FF :/OK button.
SELECT , 9 CHOOSE :/OK
A CLOCK
LANGUAGE ENGLISH
VCR PLUS+ CH.
CABLE BOX
DBS RECEIVER
TO END PUSH EXIT
Instructions continue on page 16.
TIME – – : – – AM
DATE 01/01/99
AUTO CLOCK ON
PBS CH. AUTO
D.S.T. AUTO
TIME ZONE AUTO
TO SET PUSH ,9 THEN :/OK
TO END PUSH EXIT
SELECT , 9 CHOOSE :/OK
A VCR SET UP
TUNER SET UP
INITIAL SET UP
TO END PUSH EXIT
2-3
1
VCRTV
VCR/TV
QUICK PROGRAMMING
POWER
STILL/SLOW
EJECT
CHVOL
EXIT/STATUS
TIMER
JOG/SHTL
SMARTPICTURE
INDEX AUDIO/MUTE
MENU
-
+
CBL / DBS
1 2 3
4 5 6
7 8 9
START STOP DATE
DBS DAILY
PLAY
REW FF
/OK
STOP
WEEKLY
REV
/OTR
RECREC
FWD
-+-
+
SPEED
0
CLEAR
16 Setting the Clock (cont’d)
6
Press the PLAY 8 or STOP 9 button repeatedly to set
the YEAR. When the year is correct, press the FF :/OK
button. The day of the week will appear automatically.
8
Press the EXIT/STATUS button.
5
Press the PLAY 8 or STOP 9 button repeatedly to set
the DATE (month and day). Every time you press the PLAY
8 or STOP 9 button, the day changes in one-day increments. If
you press and hold the PLAY 8 or STOP 9 button, the day
changes in 15-day increments.
When the month and day are correct, press the FF :/OK
button.
7
Press the FF :/OK button once again to skip “AUTO
CLOCK” and go to “D.S.T.” (Daylight Savings Time).
Press the PLAY 8 or STOP 9 button to set D.S.T. to ON
or OFF. If AUTO CLOCK is OFF, you may set D.S.T. to ON or
OFF only. For more information, please see page 20.
4
Press the PLAY 8 or STOP 9 button repeatedly to set
the TIME. Every time you press the PLAY 8 or STOP 9 button,
the time changes in one-minute increments. If you press and hold
the PLAY 8 or STOP 9 button, the time changes in 30-minute
increments.
When the time is correct, press the FF :/OK button.
TIME 10 : 45AM
DATE 01/01/99
AUTO CLOCK OFF
D.S.T. ON
TO SET PUSH ,9 THEN :/OK
TO END PUSH EXIT
TIME 10 : 45AM
DATE 07/31/99
AUTO CLOCK OFF
D.S.T. ON
TO SET PUSH ,9 THEN :/OK
TO END PUSH EXIT
TIME 10 : 45AM
DATE 07/31/99
SATURDAY
AUTO CLOCK OFF
D.S.T. ON
TO SET PUSH ,9 THEN :/OK
TO END PUSH EXIT
8
4-7
VCRTV
VCR/TV
QUICK PROGRAMMING
POWER
STILL/SLOW
EJECT
CHVOL
EXIT/STATUS
TIMER
JOG/SHTL
SMARTPICTURE
INDEX AUDIO/MUTE
MENU
-
+
CBL / DBS
1 2 3
4 5 6
7 8 9
START STOP DATE
DBS DAILY
PLAY
REW FF
/OK
STOP
WEEKLY
REV
/OTR
RECREC
FWD
-+-
+
SPEED
0
CLEAR
Setting the Clock (cont’d) 17
6
Press the EXIT/STATUS button.
7
An on-screen message will ask you to turn off the VCR.
Press the POWER button to turn off the VCR.
Auto will flash in the display panel until the clock is set. Leave the
VCR turned off until the time appears on the display panel.
If – – : – – appears on the display panel after you turn off the VCR
for several minutes, the VCR could not find the time. Use a different
method to set the clock.
Time Zone Selection
4
Press the FF :/OK button repeatedly to select TIME ZONE.
5
Press the PLAY 8 or STOP 9 button repeatedly to select
your Time Zone, then press the FF :/OK button.
• When the power plug is connected
to an AC outlet, the correct time will
appear on the display panel of the
VCR when the power is off.
• Press the EXIT/STATUS button
repeatedly to make the time appear
on the display panel when the VCR
power is on.
Helpful Hints
3
Press the PLAY 8 or STOP 9 button to select CLOCK,
then press the FF :/OK button. CABLE BOX USERS SET
CLOCK MANUALLY will appear briefly.
(If AUTO CLOCK is set to OFF, TIME ZONE will not be available
in the menu. If this happens, press the FF :/OK button repeatedly
to select AUTO CLOCK, then press the PLAY 8 or STOP 9
button to set AUTO CLOCK to ON.)
SELECT , 9 CHOOSE :/OK
A CLOCK
LANGUAGE ENGLISH
VCR PLUS+ CH.
CABLE BOX
DBS RECEIVER
TO END PUSH EXIT
TIME – – : – – AM
DATE 01/01/99
AUTO CLOCK ON
PBS CH. AUTO
D.S.T. AUTO
TIME ZONE AUTO
TO SET PUSH ,9 THEN :/OK
TO END PUSH EXIT
1
Press the VCR button, then press the MENU button.
2
Press the PLAY 8 or STOP 9 button to select INITIAL
SET UP, then press the FF :/OK button.
2-5
6
1
7
VCRTV
VCR/TV
QUICK PROGRAMMING
POWER
STILL/SLOW
EJECT
CHVOL
EXIT/STATUS
TIMER
JOG/SHTL
SMARTPICTURE
INDEX AUDIO/MUTE
MENU
-
+
CBL / DBS
1 2 3
4 5 6
7 8 9
START STOP DATE
DBS DAILY
PLAY
REW FF
/OK
STOP
WEEKLY
REV
/OTR
RECREC
FWD
-
+-+
SPEED
0
CLEAR
3
Press the PLAY 8 or STOP 9 button to select CLOCK,
then press the FF :/OK button. CABLE BOX USERS SET
CLOCK MANUALLY will appear briefly.
(If AUTO CLOCK is set to OFF, PBS CH. will not be available in
the menu. If this happens, press the FF :/OK button to select
AUTO CLOCK, then press the PLAY 8 or STOP 9 button to
set AUTO CLOCK to ON.)
18 Setting the Clock (cont’d)
6
Press the EXIT/STATUS button.
5
Press the PLAY 8 or STOP 9 button repeatedly to select
the station number of your PBS channel.
Manual PBS Channel Selection
4
Press the FF :/OK button to select PBS CH.
1
Press the VCR button, then press the MENU button.
2
Press the PLAY 8 or STOP 9 button to select INITIAL
SET UP, then press the FF :/OK button.
TIME – – : – – AM
DATE 01/01/99
AUTO CLOCK ON
PBS CH. AUTO
D.S.T. AUTO
TIME ZONE AUTO
TO SET PUSH ,9 THEN :/OK
TO END PUSH EXIT
7
An on-screen message will ask you to turn off the VCR.
Press the POWER button to turn off the VCR.
Auto will flash in the display panel until the clock is set. Leave the
VCR power off until the clock is set.
If – – : – – appears on the display panel after you turn off the
VCR for several minutes, the VCR could not find the time. Repeat
steps 1-6 above, entering a different PBS channel at step 5. Or,
use a different method to set the clock.
2-5
6
1
7
VCRTV
VCR/TV
QUICK PROGRAMMING
POWER
STILL/SLOW
EJECT
CHVOL
EXIT/STATUS
TIMER
JOG/SHTL
SMARTPICTURE
INDEX AUDIO/MUTE
MENU
-
+
CBL / DBS
1 2 3
4 5 6
7 8 9
START STOP DATE
DBS DAILY
PLAY
REW FF
/OK
STOP
WEEKLY
REV
/OTR
RECREC
FWD
-
+-+
SPEED
0
CLEAR
Setting the Clock (cont’d) 19
5
Press the PLAY 8 or STOP 9 button repeatedly so that
AUTO flashes beside PBS CH.
• To display the time on the display
panel, press the EXIT/STATUS
button repeatedly.
• If you live near the boundary of an
adjacent time zone, your PBS
channel may come from a different
time zone. Use Time Zone Selection
to set your clock. Details are on
page 17.
Helpful Hints
6
Press the EXIT/STATUS button.
Automatic PBS Channel Selection
4
Press the FF :/OK button repeatedly to select PBS CH.
3
Press the PLAY 8 or STOP 9 button to select CLOCK,
then press the FF :/OK button. CABLE BOX USERS SET
CLOCK MANUALLY will appear briefly.
(If AUTO CLOCK is set to OFF, PBS CH. will not be available in
the menu. If this happens, press the FF :/OK button repeatedly
to select AUTO CLOCK, then press the PLAY 8 or STOP 9
button to set AUTO CLOCK to ON.)
1
Press the VCR button, then press the MENU button.
2
Press the PLAY 8 or STOP 9 button to select INITIAL
SET UP, then press the FF :/OK button.
TIME – – : – – AM
DATE 01/01/99
AUTO CLOCK ON
PBS CH. AUTO
D.S.T. AUTO
TIME ZONE AUTO
TO SET PUSH ,9 THEN :/OK
TO END PUSH EXIT
7
An on-screen message will ask you to turn off the VCR.
Press the POWER button to turn off the VCR.
Auto will flash in the display panel until the clock is set. Leave the
VCR power off until the clock is set. If – – : – – appears on the
display panel after you turn off the VCR for several minutes, the
VCR could not find the time. Use a different method to set the
clock.
2-5
6
1
7
VCRTV
VCR/TV
QUICK PROGRAMMING
POWER
STILL/SLOW
EJECT
CHVOL
EXIT/STATUS
TIMER
JOG/SHTL
SMARTPICTURE
INDEX AUDIO/MUTE
MENU
-
+
CBL / DBS
1 2 3
4 5 6
7 8 9
START STOP DATE
DBS DAILY
PLAY
REW FF
/OK
STOP
WEEKLY
REV
/OTR
RECREC
FWD
-
+-+
SPEED
0
CLEAR
20 Daylight-Savings Time
6
Press the EXIT/STATUS button.
Follow the steps below to program the VCR so its clock will
automatically move forward one hour in April and turn back one
hour in October.
3
Press the PLAY 8 or STOP 9 button to select CLOCK,
then press the FF :/OK button. CABLE BOX USERS SET
CLOCK MANUALLY will appear briefly. (If AUTO CLOCK is set to
OFF, PBS CH. and TIME ZONE will not appear in the menu.)
5
Press the PLAY 8 or STOP 9 button so that ON, OFF, or
AUTO appears beside D.S.T.
Select ON to make the clock adjust itself according to the VCR’s
calendar. Select OFF to turn off the feature. Select AUTO to make
the clock adjust itself according to the signal it receives from the PBS
channel. If AUTO CLOCK is set to OFF, you may only set D.S.T. to
ON or OFF.
4
Press the FF :/OK button repeatedly to select D.S.T.
SELECT , 9 CHOOSE :/OK
A CLOCK
LANGUAGE ENGLISH
VCR PLUS+ CH.
CABLE BOX
DBS RECEIVER
TO END PUSH EXIT
1
Press the VCR button, then press the MENU button.
2
Press the PLAY 8 or STOP 9 button to select INITIAL
SET UP, then press the FF :/OK button.
TIME 10:45AM
DATE 01/01/99
FRIDAY
AUTO CLOCK ON
PBS CH. AUTO
D.S.T. AUTO
TIME ZONE AUTO
TO SET PUSH ,9 THEN :/OK
TO END PUSH EXIT
7
If you set the “AUTO CLOCK” to “ON”, an on-screen
message may ask you to turn off the VCR. Press the
POWER button to turn off the VCR. Auto will flash in the
display panel until the clock is set. Leave the VCR power off until
the clock is set. If – – : – – appears on the display panel after you
turn off the VCR for several minutes, the VCR could not find the
time. Use a different method to set the clock.
2-5
6
1
7
VCRTV
VCR/TV
QUICK PROGRAMMING
POWER
STILL/SLOW
EJECT
CHVOL
EXIT/STATUS
TIMER
JOG/SHTL
SMARTPICTURE
INDEX AUDIO/MUTE
MENU
-
+
CBL / DBS
1 2 3
4 5 6
7 8 9
START STOP DATE
DBS DAILY
PLAY
REW FF
/OK
STOP
WEEKLY
REV
/OTR
RECREC
FWD
-
+-+
SPEED
0
CLEAR
Language Selection 21
5
Press the EXIT/STATUS button.
Follow the steps below to change the language of the on-screen
displays and menus.
3
Press the STOP 9 button or PLAY 8 button to select
LANGUAGE.
• If you accidentally select Spanish or
French and need English, follow
these steps.
1) Press the VCR button, then press
the MENU button.
2) Press the PLAY 8 or STOP 9
button to select SISTEMA INICIAL
or PROGRAMM. INITIALE, then
press the FF :/OK button.
3) Press the PLAY 8 or STOP 9
button to select LENGUAJE or
LANGUE.
4) Press the FF :/OK button
repeatedly so that the English menu
appears.
5) Press the EXIT/STATUS button.
Helpful Hint
1
Press the VCR button, then press the MENU button.
2
Press the PLAY 8 or STOP 9 button to select INITIAL
SET UP, then press the FF :/OK button.
SELECT , 9 CHOOSE :/OK
A VCR SET UP
TUNER SET UP
INITIAL SET UP
TO END PUSH EXIT
SELECT , 9 CHOOSE :/OK
A CLOCK
LANGUAGE ENGLISH
VCR PLUS+ CH.
CABLE BOX
DBS RECEIVER
TO END PUSH EXIT
4
Press the FF :/OK button repeatedly until your preferred
language appears.
2-4
5
1
VCRTV
VCR/TV
QUICK PROGRAMMING
POWER
STILL/SLOW
EJECT
CHVOL
EXIT/STATUS
TIMER
JOG/SHTL
SMARTPICTURE
INDEX AUDIO/MUTE
MENU
-
+
CBL / DBS
1 2 3
4 5 6
7 8 9
START STOP DATE
DBS DAILY
PLAY
REW FF
/OK
STOP
WEEKLY
REV
/OTR
RECREC
FWD
-
+-+
SPEED
0
CLEAR
Loading...