Philips VCM 6110-00T User Manual

t a"OQQOOQ 006D2&

CCD VIDEO CAMERA VCM 6110/00T

USER MANUAL

WARNING: To prevent fire or shock hazard, do not

expose this appliance to rain or moisture.

Do not attempt to disassemble the camera. In order
to prevent electric shock and fire hazard, do not
remove screws or covers. There are no user­serviceable parts inside.

Bescheinigung des Herstellers / Importeurs

Hiermit wird bescheinigt, daß die Video Kamera Typ
VCM6110/00T in Übereinstimmung mit den Bestimmungen
der AmtsbIVfrg 1046/1984 funk-entstört ist.
Der Deutschen Bundespost wurde das Inverkehrbringen
dieses Gerätes angezeigt und die Berechtigung zur
Überprüfung der Serie auf Enthaltung der Bestimmungen
eingeräumt.
Philips Novatronics
Eindhoven - Nederland

Contents

Introduction
Connecting the camera

Power supply

Video output

Synchronization

Linelock
Phase adjustment

The lens
Installing the camera
Maintenance tips
Technical specification of the camera

Page

1

1

1
2
2
2
2
2

3
3
4

Introduction

This CCD video camera produces fully interlaced monochrome
television pictures, according to the CCIR standard.
The high light sensitivity of the camera means that it can even be

used very effectively under twilight conditions. The camera is also
sensitive to infrared light. It accepts a wide range of different supply
voltages, AC as well as DC. If an AC power source is used the
camera is automatically iine-locked.

Connecting the camera

Power supply
The camera must be powered by using a separate, galvanically
isolated, AC or DC power supply unit. The AC input voltage may
vary from 12V to 28V (50Hz). The DC input voltage may vary from

10V to 39V. Use a power supply which meets the requirements for
SELV service, according to DIN/VDE 0860/05.89 or EN 60742 only.
The power supply is connected to the camera via a three pole
screw block. The three entry ports for the wiring are on the rear of
the unit. Access to the fixing screws is gained via three holes on the
underside of the unit.

Connect the power leads to (D) and (E), fig. 1.

For DC supply: (D) is - and (E) is + voltage. An extra safety ground
connection is provided, (F) fig. 1, to connect the camera to ground

potential. The maximum voltage between the supply inputs (D) and

(E) and the safety ground (F) must be less than 50 Volt.
The camera itself is galvanically isolated which makes a system with

more than one camera not susceptible to ground loop problems.

Video output
A Standard VBS video signal is available at the cinch connector, (G)
fig. 1, on the bottom of the camera. The use of a 75 ohm coaxial
cable is recommended, for example RG-59/U.

Synchronization

The camera generates a Videosignal with synchronization pulses
corresponding to the CCIR-standard. The camera can be used
alone or as a part of a larger system. Synchronizing more cameras
is possible when an AC power source is used.
When several video cameras share the same video recorder

equipment, the video recording will be unsynchronized for a period

of time after switching from one camera to another. On the monitor
this is seen as rolling of the video image.
This effect can be avoided by locking the camera to the locai line
frequency: linelock. For this reason the camera is already locked to
the local line frequency when an AC power source is used. The
Vphase potentiometer, (C) fig. 1, enables a phase adjustment of
the linelock over 240 degrees.

The lens

Your camera is equipped with an integrated, 4 mm, f/2.0 lens,

(A) fig. 1, with a viewing angle of 74“ horizontally and 55“

vertically. The depth of field ranges from 1 metre to infinity.

Warning:
Do not touch the surface of the lens. This could damage the
delicate coating on the surface of the lens. If the lens has to be
cleaned, use special lens cleaning tissue, available at any good
camera store.

Installing the camera

It is advisable to install the camera first and connect it to the

monitor on the spot. It will allow you to properly aim the camera at
the area you want covered while checking the results on the

monitor. When satisfied you can place the monitor in its permanent

position.
The camera is provided with a mounting hole with 1/4“ Whitworth
thread. (B) fig. 1, which makes it possible to mount it on any

camera tripod.

Maintenance tips

Warning: Do not expose the camera to rain or moisture, or try to

operate it in wet areas. Do not operate the camera if it
gets wet.

For outdoor applications you should use a protective housing to
shield the camera from rain and snow.

Cleaning. You may clean the exterior of the camera with a damp
and lint-free cloth or chamois. Do not use strong or abrasive
detergents. In case the dirt is hard to remove, use mild detergent
and wipe gently.

Technical specification of the camera

Image pick-up device
Horizontal resolution 380 TV lines
Scanning system
Synchronization

Output signal
Integrated lens 4 mm, f/2.0 fixed focus (1 m to

Viewing angle
Illumination range

Tripod mount 1 /4" Whitworth thread
Video connection socket Cinch (RCA) plug
Input voltage 12 - 28V AC or 10 - 39V DC,

Power consumption 1.5 VA
Ambient temperature -20“Cto +55“C (operating)

Relative humidity 20 to 90% (operating)

Dimensions
Weight

1/3" CCD

CCIR 625 lines interlaced

Vertically phase-locked (line­lock) to power supply
frequency.

Phase adjustment range is

240“
Standard VBS signal

infinity)

74“ horizontal, 55“ vertical
4 to 25000 lux (50 ire/ -6dB)

1 to 25000 lux (acceptable
picture)

using same connection

terminals

-25“Cto +70“C (storage)

up to 90% (storage)

70 X 70 X 54 (mm)

130 gr.

—i—j—\

Fig. 1

Rmtvísw

Q00(^

~t—i

----\-----

-------

(B)(É)(E) (fe

Sidsviaw Front vi«w

^

V

3122 165 20214

Printed in The Netherlands