Philips TU5351/BE071P User Manual

Onis 300

Charge handset(s) for 24 hours before use.

This equipment is not designed for making emergency telephone calls when the power fails.

Onis 300 Vox Onis 300 Duo Vox

Menu overview

By using the Pilot key on the side of the handset you can scroll through the menus.

Ringer type p.11

Ringer volume p.12

Earpiece tone p.12

Key & feedback tones p.12

Notification beep p.12

SMS

Send SMS p.9

SMS list p.10

SMS settings

Babysit mode p.12

Registration

Un-register handset p.13

Rename handset p.13

Change languages* p.13

Date & time p.14

Display contrast p.14

Listening to messages p.15

Saved messages

Answer machine (Onis 300 Vox)

SMS mode p. 10

SMS boxes p.10

SMS center p.11

Validity period* p.11

Sounds

Handset

Deleting messages p.15

Record memo p.18

Answer mode p.16

Record personal message p.16

Outgoing messages

Settings

Intercom

Answer mode (ON/OFF) p.15

Call all p.19

Rings before answer p.16

Handset list p.19

Voice prompts p.16

Call screening p.17

Recording quality p.17

Remote control p.17

Sounds

Base

Ringer type p.27

Record a personal melody p.27

Ringer volume p.27

Music on hold p.27

Registration p.27

Line settings

Dial mode* p.28

Extra

Network p.28

Recall type* p.28

Call cost & duration*

VIP melody function p 25

Operator type* p.28

View total p.25

First ring p.28

Unit cost p.25

Service codes settings p.28

Alarm clock

Activation p.25

Settings p.26

Do Not Disturb mode p.26

Network

Cheapest rates fct p.23

Operator Services p.24

View p.21

Add new p.20

Phonebook

Incoming calls p.23

Outgoing calls p.23

Delete all p.23

Settings

View P.22

Call log

* Country dependent

Pilot key

Press to enter the carousel or validate

a menu or an option

- Scroll to navigate in the menus &

options

- Move the cursor left/right

- Scroll up to reach Intercom from

idle mode

- Scroll down to reach Cheapest

rates prefix from idle mode

A long press to unlock the keypad

Loudspeaker

- A short press to take the line or activate the handset loudspeaker during a call

- A long press to activate the base loudspeaker during a call (Onis 300 Vox)

Onis 300

Handset

Earpiece

Line key

Press to take the line, answer a call or hang up

Correct key

- To correct a digit when predialling or a character when editing

- A short press to go back one menu when navigating

- A long press to return to idle mode when navigating

- To insert R for operator services when on line

Phonebook

- A short press to access the phonebook

- A long press to add a new entry

Call log

- A short press to access the call log

- A long press to directly access the vocal messages list (Onis 300 Vox)

Keypad lock & Editing

- A short press to insert *

- A long press to lock/unlock the keypad in idle mode

- A long press to enter multitap or Eatoni editor when entering text

Icons

Answer machine ON

(Onis 300 Vox)

External call in

progress

Internal call in

progress

Handset loudspeaker

Ringer deactivated

Registered & in range

of the base

Do Not Disturb & case mode

- A short press to insert # (pause) when dialling

- A long press to activate/deactivate the Do Not Disturb mode

- Press to switch case mode when editing

Alarm clock

Microphone

Blinking

New message on answering

machine or voice mailbox

- Incoming external call in progress

- Line is already busy

Internal incoming call

Base loudspeaker ON

(Onis 300 Vox)

New SMS

Not registered

- A short press to dial 0

- A long press to activate/deactivate the alarm clock

Fast blinkingSteady ON

Answer machine full

SMS memory full

The battery symbol

When charging, the battery bars scroll : When the handset discharges, the battery shows the status : Full , 2/3 , 1/3 and empty .

Onis 300 handset

Event indicator (red) Blinking : New events (new SMS, missed calls etc...) Fast blinking : SMS Memory full

Paging key

Press to locate all handsets

Answer machine control keys

ON/OFF key

Press to switch answer machine ON/OFF

Play/Stop key

Press to listen to the new messages

Delete key

Press to delete current message Long press to delete all the messages (except unread ones)

Next key

Press to listen to the next messages

Previous key

Press to listen to the previous messages

Loudspeaker

Onis 300 Base station

Power indicator (green) ON : System correctly connected to the mains

OFF : System not powered Blinking : the line is busy

Onis 300 Vox Base station

Base loudspeaker volume keys

Answer machine indicator (red)

ON : Answer machine activated OFF : Answer machine

deactivated

Blinking : New messages Fast blinking : Answer machine

memory full

Power indicator (Green) ON : System correctly connected to the mains

OFF : System not powered Blinking : the line is busy

Paging key

Press to locate all handsets

Using GAP standard compliance

The GAP standard guarantees that all DECTTMGAP handsets and base stations comply with a minimum operating standard irrespective of their make.Your Onis 300 handset and base station are GAP compliant, which means the minimum guaranteed functions are : register a handset, take the line, receive a call and dial. The advanced features may not be available if you use another handset than an Onis 300 with your base station. To register and use your Onis 300 handset with a GAP standard base station of a different make, first follow the procedure described in the manufacturers instructions, then follow the procedure page 12. To register a handset from another make to the Onis 300 base station, place the base station into registration mode (page 12), then follow the procedure in the manufacturers instructions.

Some DECTTMperipherals, such as repeaters, do not have a keypad.A special menu-operated procedure is used to register such peripherals with the base station without the need to disconnect the base station. See page 27 and use the peripheral instructions to register it to the base station.

Base stations

Onis 300 handset 1 Icons 1 Base stations Onis 300 & Onis 300 Vox 2 GAP Standard 2 Table of contents 3

Conformity,Environment and Safety 4 Installing the base station 4 Installing and replacing the batteries 4 Battery life and range 4

Introduction

Screen in idle mode 5 Understanding the menu system 5 How to navigate in the menus 5

Calling/answering a call/other principles 6

In-call features 7

Editing systems 8

Sending SMS

Sending SMS 9 Reading the private SMS 10 SMS settings 10-11

Handset

Setting the standard ringer type 11 Setting the ringer volume 12 Setting the earpiece tone 12 Setting the key & feedback tones 12 Setting the notification beep 12 Babysit mode 12 Registering/unregistering an additional handset 12-13 Using Onis 300 handset with several base stations 13 Renaming the handset 13 Changing the language 13 Setting the date and time 14 Setting the display contrast 14

Using the answer machine (Onis 300 Vox)

Setting the answer machine ON/OFF 14-15 Listening to your messages 15 Deleting messages 15 Selecting the answer mode and the outgoing message type 15-16 Recording your personal outgoing message 16

Setting the number of rings before answer 16 Setting the voice prompts 16 Setting the call screening 17 Setting the recording quality 17 Activating the remote control 17 Using the remote control 17-18 Changing remote control code 18 Recording a local message (memo) 18

Using the intercom

Making internal calls/activating babysit mode 19 Transfering a call 19 Using conference call 19

Using the phonebook

VIP settings 20 Adding a name 20 Calling from phonebook 20 Viewing the phonebook 20-21

Using the call log

Viewing the call log 22 Deleting the call log 23 Setting the call log 23

Network

Using the cheapest rates function 23 Using the operator services 24

Using the extra features

Setting the VIP ringer type 25 Setting the call cost & duration 25 Setting the alarm clock 25 Setting the Do Not Disturb mode 26

Base

Setting the standard ringer type 27 Record a personal melody 27 Setting the ringer volume 27 Setting music on hold 27 Registration 27 Setting the line 28 Setting the service codes 28

Troubleshooting

Index

Philips has marked the battery and packaging with standard symbols designed to promote the recycling and appropriate

disposal of your eventual waste.

A financial contribution has been paid to the associated national recovery & recycling system.

The labelled packaging material is recyclable.

DECTTMis a Trade Mark of ETSI registered for the benefit of the implementers of the DECT technology.

Table of contents

Conformity, Environment and Safety Safety information : This equipment is not designed to make emergency calls when the power fails. An

alternative has to be made available to allow emergency calls. Conformity : See back cover page. In case you need a copy of the original certificate please contact the customer service centre.This product can only be connected to the analogue telephone network in the area which is indicated on the label placed on the packaging. Power requirements : This product requires an electrical supply of 220-240 volts, alternating monophased power, excluding IT installations defined in standard EN 60-950. Warning ! The electrical network is classified as dangerous according to criteria in the standard EN 60-

950.The only way to power down this product is to unplug the power supply from the electrical outlet. Ensure the electrical outlet is located close to the apparatus and is always easily accessible. Telephone connection : The voltage on the network is classified as TNV-3 (Telecommunication Network Voltages, as defined in the standard EN 60-950). Safety precautions : Do not allow the handset to come into contact with water. Do not open the handset or the base station.You could be exposed to high voltages. Do not allow the charging contacts or the battery to come into contact with conductive materials. (1). Environmental care : Please remember to observe the local regulations regarding the disposal of your packaging materials, exhausted batteries and old phone and where possible promote their recycling.

Installing the base station

To properly install the base station, plug the line cord and the power cable into the base station. Plug the cord and the cable into the wall. The green indicator on the base station and a beep indicate that the phone is properly installed.

Warning : Always use the cables provided with the product.

(1) Do not insert anything in this opening.

Installing and replacing the batteries

To insert the batteries, open the battery cover, place the batteries as indicated and put the battery cover back. When the handset is placed on the base station the 3 battery bars scroll (if charge is needed).Allow the handset to charge for 24 hours to reach full charge. On first use it may be necessary to wait for a few minutes before seeing symbols on the display. In case you need to change the batteries, the following type is mandatory R03/AAA NiMh 600/650 mAh.

Warning :The base station must always be plugged into the mains when charging. Always use rechargeable batteries.

Battery life and range

The battery life is about 250 hours in stand by time (when the handset is in idle mode & ready to receive a call) and around 16 hours in communication. A battery low alert will inform you that the handset has to be recharged, if this is during a call, the call will end shortly after the alert.

Optimal battery life is reached after 3 cycles of full charge/discharge.

Under ideal conditions the range is a maximum of 50 metres indoors and 300 metres outdoors. When reaching the range limit, the conversation will become crackly, move closer to the base station otherwise the call will be cut off. To reach optimal range place the base station away from electrical appliances.

Conformity, Environment & Safety

Batteries should not be disposed of with general household waste.

The screen in idle mode

In idle mode, the Onis 300 display shows different information :

In normal idle mode the display shows the date & time, the name of the handset and the instruction to access the menu.

Missed calls , new SMS or new messages (answer machine) or

(voice mailbox), if any, are displayed in idle mode. The pilot key

on the side of the handset gives access to the corresponding menu.

Do Not Disturb mode , and the alarm clock , if activated, are also displayed on the idle screen. To modify these settings use & on the keypad.

Understanding the menu system

To access the carousel menu from idle screen press on the side of the handset. The carousel represents a loop of icons that gives access to the different

first level menus. Scroll up or down to reach the desired menu. Press

to validate.

The sub menus are listed and represented by little squares at the bottom

of the display.To reach one particular sub-menu use the pilot key and

press to validate your choice. A tick shows the selected sub-menu or option. The shows the option you are browsing.

Note : Certain menus are also directly accessible via a dedicated key on the

keypad (example Phonebook , Call log ).

Example of navigation in the menus

To reach the ringer type menu

Press to select

These steps are described as follows in this manual :

Scroll up or down

Press to select

To change the ringer type

1- (Press) to enter the carousel menu 2- (Go to) Handset, press (validate) 3- (Select) Sounds, press (validate) 4- (Select) Ringer type, press (validate) 5- The first option of the ringer type sub-menu is displayed External

Standard ringer

6- Scroll to change sub-menu or validate to see the list of melodies

Introduction

Press to select

Press to see

the list of

melodies

& listen

Basic principles

Making a call

Pre-dialling

1- Dial from keypad

To correct a digit use 2- Make the call Talk to the other party

3- Hang up

Calling from phonebook

1- to enter carousel 2- to reach the phonebook menu

3- to select the menu, 4- to reach the name

5- Select Call in the options or make the call

Note :You can also press to directly reach the phonebook

Answering/ending a call

When the phone rings, press to answer the call. To stop the phone from ringing without answering, press to select

Silence

Calling from the call log (Redial or call back last caller)

To redial a number through the call log, press and select from the list.

Direct dialling

1- Connect the line 2- Dial from the keypad Talk to the other party

3- Hang up

Press to enter the options and select Call or directly press

To chain dial (predial mode)

You can chain dial 2 numbers. (One predialled and the other one from the

phonebook or the call log, or both from the phonebook).

1- Predial the number (for example, operator prefix)

2- Use or to open the call log or the phonebook

3- Scroll through the list

4- Select an entry and validate

You can move the cursor , erase or change a digit with

5- Connect the line

Note : It is possible to chain dial in direct dialling mode.You can also

retrieve numbers from the SMS list or the Cheapest Rates menu.

Calling/answering a call/other principles

In-call features

During an external call you can access additional features available in the in-call options. Press to enter the Options.

To mute the handset microphone

1- Press 2- Scroll to Mute and validate The caller can no longer hear you.

To resume the conversation press again to Unmute.

Intercom (if there are several Onis 300 handsets)

During a call, you can put a call on hold, transfer an external call or share the conversation on conference call : 1 external caller + 2 internal callers (See page 19).

To record a conversation (Onis 300 Vox)

1- While on line press 2- Scroll to Record and validate The call is recorded for a maximum of 6 minutes on the answer machine.

To continue recording resume from step 1 above.

To listen to the conversation use the Call log menu or the messages list ( ).

Warning : Recording a conversation may be illegal.We advise you to inform the person you are calling.

During an internal call other in-call features are available, such as Switch and End intercom.

To switch the loudspeaker ON/OFF

Press to activate/deactivate the louspeaker on the handset. A long press activates the base loudspeaker (Onis 300 Vox).

To increase/decrease the handset earpiece or loudspeaker volume during a call

Scroll the pilot key up or down on the side of the handset.

Or use the keys on the base station.

CLI/Call waiting

If you subscribe to that service, a beep in the earpiece informs you of a second incoming call. The name or the number of the second caller may be displayed if you also subscribe to the Caller Line Identification service.To answer that second call, use then (according to your network, the code may be different). Please contact your network provider for more details.

In-call features

Editing systems

Capitalisation

By default, the first letter of a sentence is in upper case. Use to change the case mode : all characters in upper case (AB) or all letters in lower case (ab). Punctuation and mathematical marks are

available through while other special characters are available on .

Scroll to move the cursor left or right. Press to delete a character ; a long press deletes the whole text.

Onis 300 uses two editing systems : Multi-tap and Eatoni®. Make a long press on to switch between both systems. Lets compare both systems to write Peter.

The standard multi-tap system allows you to enter the text character by character, pressing the corresponding key as many times as necessary to reach the desired character.

To write Peter with multi-tap

Press once : P

Press twice : Pe

Press once : Pet

Press twice : Pete

Press three times : Peter

Keypad Keys

1 2 3 4 5 6 7 8 9 0

Multi-tap Sequence

[space] 1 @ _ # = < > ( ) & ¤ £ $ ¥ a b c 2 à ä ç æ å d e f 3 è é ) N g h i 4 ì G j k l 5 7 m n o 6 ñ ò ö p q r s 7 ß A 2 E t u v 8 ù ü w x y z 9 f S X Q . 0 , / : ; " ' ! ¡ ? ¿ * + - %

The Eatoni®system is a new predictive editing system designed to help you write an SMS. A little E in the header helps you know the mode you are using.

Eatoni

is a word editor that chooses the most probable letter.

The operation of the Eatoni

system is the following : Press the key that displays the character you want to edit.The character that is most likely to be correct is displayed on the screen. If it does not match the expected letter, press to display the next most probable character available on the key.

To write Peter with Eatoni

Press

Press to

activate Eatoni

Press to

Press

change character

Press

Press to validate the name.

Press

Editing systems

Press

Eatoni®& LetterWise are trademarks of Eatoni Ergonimics, Inc. and used by Philips under license.

+ 23 hidden pages