Philips SPP6263WB/37 quick start guide

Page 1
Home Power
SPP6263WB/37
User manual
1. Plug the surge protector into a standard grounding duplex wall receptacle, covering both outlets, by fully inserting the blades and ensure that there are no exposed conductors.
2. The surge protector will now be providing power and surge protection.
3. Make sure electronic equipment is turned o before plugging into the surge protector outlets. Do not use extension cords to connect equipment to the surge protector.
4. Connected equipment can now be turned on.
5. Hold the surge protector rmly against wall when removing plugs to prevent it from pulling loose.
USB Charging
• 2.1 Amp total output allows you to charge one tablet or two smartphones at full capacity at the same time. Recharge your device at a maximum speed of
2.1 Amp when connected to a single port.
• The USB ports are used to charge portable electronic devices only. There is no data transfer capability.
NOTE: Check the blue “PROTECTED” indicator light periodically. A glowing blue indicator light shows that surge protection is being provided. If the blue “PROTECTED” indicator light stops glowing, the surge protective components have expired — though power will still be supplied to the outlets, now unprotected.
To ensure the protection of your electronics the surge protector should be replaced.
Surge Protector — Limited-Lifetime Warranty
This surge protector is warranted to be free of defects in workmanship and/or materials for the life* of the surge protector. If such a defect should arise during the life of the surge protector, we will, at our option, either repair or replace the surge protector without charge. This warranty does not cover damage caused by lightning, accident, misuse, or alterations to the surge protector.
* This surge protector, like all surge protectors, has a nite lifespan. Even under normal circumstances and in the absence of defects, the product’s life will expire when the surge protector’s component capacity has been exceeded, thereby ceasing to provide protection from surges.
Warranty replacement procedure
1. Call our Customer Information Center at 1-844-816­0320 to get a Return Authorization Number (RA#), shipping instructions and a prepaid return address label.
2. Return the said surge protector, freight prepaid, to us. Surge protectors returned to us must have an RA# included in the mailing address to be accepted.
3. The original purchaser will be asked to send the surge protector, a copy of the sales receipt for the product, your name, address, phone number and a description of the problem.
Connected Equipment Warranty
Equipment Replacement Guarantee for Surge Model: SPP6263WB/37 Maximum Warranty Amount: $50,000(USD)
NOTE: This device is not a lightning arrestor, so it will not aord protection when lightning strikes nearby power line, the house, service entrance or antenna. The warranty is void if a power disturbance damages your equipment through the coax, phone or network lines.
We will pay up to the maximum warranty amount oered for the surge protector purchased to repair or replace up to an amount equal to the fair market value or the original purchase price, whichever is less, of your electronics equipment, if damaged by a transient surge (except those caused by direct lightning), within the life* of the surge protector, while properly and directly connected to this surge protector. WE DISCLAIM AND ASSUME NO LIABILITY FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OR DAMAGE TO SOFTWARE OR DATA OR DAMAGES OR COSTS ASSOCIATED WITH BUSINESS INTERRUPTION OR OTHER DAMAGES DUE TO LOSS OR DAMAGE TO EQUIPMENT, SOFTWARE OR DATA. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specic legal rights, and you may also have other rights that may vary from state to state.
This warranty is secondary to any existing coverage of any connected equipment, including but not limited to, any manufacturer’s warranty, extended warranties, or insurance coverage.
To qualify for a connected equipment warranty:
1. All connected equipment must be safety certied by a Nationally Recognized Testing Laboratory.
2. The said surge protector must be plugged into properly wired and grounded outlets, no extension cords, adapters, other ground wires or electrical connectors may be used, with the sole exception of other standard 120 volt products approved for that use. The installation must comply with all applicable electrical and safety codes set forth pursuant to the National Electrical Code (NEC).
3. Any claim under the warranty policy must be made within 15 days of the date of the alleged damage to the connected equipment.
For connected equipment coverage, the following conditions must be satised:
A. All equipment eligible for warranty coverage must
be plugged directly into said surge protector. Equipment connected to the protected equipment, but not plugged directly into the surge protector will not be covered.
B. The equipment must have been damaged by a
covered power disturbance that passed through the said surge protector.
C. The said surge protector must be damaged from the
power disturbance.
D. The said surge protector’s protection capacity must
not have been exceeded.
Connected equipment claim procedure:
1. Call our Customer Information Center at 1-844-816­0320 to get a Return Authorization Number (RA#), shipping instructions and a prepaid return address label.
2. After you have received the prepaid return address label, return the surge protector, freight prepaid, to us. Surge protectors returned to us must have an RA# included in the mailing address to be accepted.
3. We will determine whether the damage to your equipment is covered by this warranty policy. If you are covered, a claims adjuster will contact you and we will do one of the following at our own discretion:
a. Authorize a service center to repair damaged
equipment.
b. Replace damaged equipment with equivalent
or better.
c. Reimburse customer the fair market value of the
damaged equipment.
d. Reimburse customer the initial purchase price of
the damaged equipment (customer to provide dated bill of sale).
4. We retain the right to determine whether the damage to the connected equipment is due to said surge protector failure by requesting that damaged equipment be sent to us for inspection.
WARNING
RISK OF ELECTRIC SHOCK
• DO NOT USE IN WET LOCATIONS
• KEEP CHILDREN AWAY
• USE INDOORS ONLY
• FULLY INSERT PLUG RISK OF FIRE
• DO NOT EXCEED
ELECTRICAL RATINGS
NOT FOR USE WITH
• AQUARIUMS OR OTHER WATER- RELATED PRODUCTS
• GENERATORS AND
POWER INVERTERS
• MEDICAL LIFE-SUPPORT PRODUCTS
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, USE ONLY INDOORS.
UNIT SHOULD BE PLUGGED INTO AN INTERIOR GROUNDED PARALLEL DUPLEX RECEPTACLE. NOT FOR USE WITH GROUND­FAULT CIRCUIT-INTERRUPTER RECEPTACLES OR RECEPTACLES WITH INDICATOR LIGHTS OR CONTROL. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS DEVICE WITH A RECEPTACLE IN WHICH THE SLOT OPENINGS DO NOT ALIGN WITH THE BLADES.
MADE IN CHINA This product is distributed by and warranted by Jasco
Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114, for © 2017 Gibson Innovations Limited. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by Gibson Innovations Ltd. under License from Koninklijke Philips N.V.
Questions? Contact us at 1-844-816-0320 between 7:00AM—8:00PM CST.
SPP6263WB/37 v1
08/08/17 KN
Page 2
Home Power
SPP6263WB/37
Manual de usuario
1. Enchufe el supresor de sobretensiones en un tomacorriente mural estándar doble con conexión a tierra (cubra ambos tomacorrientes) colocando bien la clavija y asegúrese de que no haya quedado ningún conductor expuesto.
2. El supresor de sobretensiones ahora debería estar habilitado para proporcionar corriente y protección contra sobretensiones.
3. Asegúrese de que el equipo electrónico esté apagado antes de enchufarlo al tomacorriente del supresor de sobretensiones. No utilice un cable de extensión para conectar el equipo al supresor de sobretensiones.
4. Ahora puede encender el aparato conectado.
5. Al desenchufar algún aparato, sostenga el supresor de sobretensiones con rmeza para que no se aoje de la pared.
Carga USB
• 2,1 Amp de salida total le permiten cargar completamente una tableta o dos teléfonos inteligentes al mismo tiempo. Recargue su dispositivo a la velocidad máxima de 2,1 Amp cuando lo conecte a un solo puerto.
• Los puertos USB se utilizan solo para cargar dispositivos electrónicos portátiles. No se ofrecen funciones de transferencia de datos.
NOTA: Verique la luz azul indicadora de “PROTECCIÓN” con regularidad. Cuando el indicador tiene un color azul brillante signica que la protección contra sobretensiones está habilitada. Si el indicador de “protección” azul deja de brillar, los componentes de protección del supresor de sobretensión han vencido*, pero los tomacorrientes seguirán recibiendo suministro de energía, ahora sin protección. Para garantizar que sus equipos electrónicos estén protegidos, deberá cambiar el supresor de sobretensiones.
Supresor de sobretensiones — Garantía de por vida limitada
Se garantiza que este supresor de sobretensiones no tendrá defectos de materiales o de manufactura durante toda su vida útil. En caso de que surgiese algún defecto durante la vida útil del supresor de sobretensiones, repararemos o reemplazaremos, según nuestro criterio, el supresor de sobretensiones sin ningún cargo. La presente garantía no cubre daños producidos por rayos eléctricos, accidentes, maltrato o modicaciones al supresor de sobretensiones.
*Este supresor de sobretensiones, como cualquier supresor de sobretensiones, tiene una vida útil limitada. Incluso en circunstancias normales y ante la ausencia de defectos, la vida útil de este producto terminará cuando se haya agotado la capacidad de los componentes del producto, y en tal momento dejará de proporcionar protección contra sobretensiones.
Procedimiento de la garantía para la reposición
1. Llame al centro de atención al cliente al 1-844-816­0320 para obtener un número de autorización de devolución (RA#), así como las instrucciones para el envío y una etiqueta prepagada con la dirección para la devolución.
2. Envíenos el supresor de sobretensiones, con franqueo pagado. A n de que se acepten los supresores de sobretensiones devueltos, estos deben incluir el número RA en la dirección postal.
3. Se le solicitará al comprador original que envíe el supresor de sobretensiones, una copia del recibo de compra del producto y que especique su nombre, dirección, número telefónico y una descripción del problema.
Garantía de equipos conectados Garantía de reposición de aparatos para el modelo de
supresor: SPP6263WB/37 Monto máximo de la garantía: USD 50 000
NOTA: Este dispositivo no es un pararrayos, de modo que no ofrece protección cuando caiga un rayo en los cables de tensión cercanos, en la casa, entrada de servicio o en la antena. La garantía queda anulada si una perturbación eléctrica causa daños a su equipo a través del cable coaxial, telefónico o de la red.
Pagaremos hasta el importe máximo de la garantía ofrecida por el supresor de sobretensiones para reparar o cambiar el aparato electrónico hasta un monto igual al valor real de mercado o al precio de compra original, el que fuera menor, si se produce un daño por sobretensiones transitoria (salvo la provocada por la caída directa de un rayo) dentro de la vida útil* del supresor de sobretensiones, siempre y cuando el aparato electrónico dañado haya estado debida y directamente conectado a este supresor de sobretensiones. NO ASUMIMOS NINGUNA RESPONSABILIDAD POR DAÑOS Y PERJUICIOS, INCIDENTALES O CONSECUENTES, INCLUSO DE MANERA NO LIMITATIVA: POR LA PÉRDIDA O DAÑO DE SOFTWARE O DATOS O DAÑOS O COSTOS ASOCIADOS CON LA INTERRUPCIÓN DE LAS ACTIVIDADES COMERCIALES U OTROS DAÑOS, DEBIDO A LA PÉRDIDA O DAÑO DEL EQUIPO, DEL SOFTWARE O DE DATOS. Algunos países no permiten la exclusión o limitación de la cláusula sobre daños incidentales o consecuentes, por este motivo las limitaciones arriba mencionadas pueden no aplicarse en su caso. Esta garantía le otorga derechos legales especícos, es posible que tenga otros derechos que pueden variar según el estado en el que vive.
Esta garantía es secundaria a cualquier otra cobertura existente que tengan los equipos conectados, incluso, de manera no limitativa, a toda garantía del fabricante, garantías ampliadas o coberturas de seguros.
Para calicar para la garantía de equipos conectados:
1. Todos los equipos conectados deben contar con un certicado de seguridad emitido por un laboratorio de pruebas reconocido a nivel nacional.
2. El supresor de sobretensiones debe estar enchufado a un tomacorriente correctamente cableado y con conexión a tierra; no se deben usar cables de extensión, adaptadores, otros cables de conexión a tierra ni conectores eléctricos; solo se podrán usar otros productos estándar de 120 V aprobados para dicho uso. La instalación debe cumplir con todos los códigos eléctricos y de seguridad conformes al Código Estadounidense de Normas de Electricidad (NEC).
3. Todo reclamo presentado durante la validez de la póliza de garantía se debe realizar en un plazo de 15 días tras haberse producido el supuesto daños del equipo conectado.
Se deben cumplir las siguientes condiciones para obtener la cobertura del equipo conectado:
A. El equipo elegible para recibir la cobertura de
la garantía debe estar enchufado directamente al supresor de sobretensiones. Todo equipo que esté conectado al equipo protegido, pero no esté enchufado directamente al supresor de sobretensiones, no estará cubierto por esta garantía.
B. El equipo deberá haber sido dañado por una
perturbación eléctrica —cubierta por la garantía—
que haya atravesado al supresor de sobretensiones.
C. El supresor de sobretensiones tuvo que haber sido
dañado por dicha perturbación eléctrica.
D. No deberá haberse superado la capacidad de
protección del supresor de sobretensiones.
Procedimiento de reclamo para equipos conectados:
1. Llame al centro de atención al cliente al 1-844-816­0320 para obtener un número de autorización de devolución (RA#), así como las instrucciones para el envío y una etiqueta prepagada con la dirección para la devolución.
2. Una vez que haya recibido la etiqueta prepagada con la dirección para la devolución, envíenos el supresor de sobretensiones, franqueo pagado. A n de que se acepten los supresores de sobretensiones devueltos, estos deben incluir el número RA en la dirección postal.
3. Determinaremos si el daño del equipo está cubierto por esta póliza de garantía. Si está cubierto, el tasador responsable del reclamo se contactará con usted, y tomaremos, a nuestra total discreción, una de las siguientes medidas:
a. Autorizaremos a un centro de reparaciones para
reparar el equipo dañado.
b. Cambiaremos el equipo dañado por otro
equivalente o mejor.
c. Reembolsaremos al cliente el valor real de
mercado del equipo dañado.
d. Reembolsaremos al cliente el precio de compra
original pagado por el equipo dañado (el cliente deberá proporcionar la factura de compra fechada).
4. Nos reservamos el derecho de determinar si el daño al equipo conectado se debe a una falla del supresor de sobretensiones; para ello, podrá solicitar que se le envíe el equipo dañado para su inspección.
ADVERTENCIA
RIESGO DE DESCARGA ELÉCTRICA
• NO UTILICE EN LUGARES HÚMEDOS
• MANTENGA FUERA DEL ALCANCE DE LOS NIÑOS
• SOLO PARA USO EN INTERIORES
• ENCHUFE COMPLETAMENTE LA CLAVIJA
RIESGO DE INCENDIO
• NO SUPERE LOS VALORES NOMINALES ELÉCTRICOS
NO USAR CON
• ACUARIOS NI OTROS PRODUCTOS QUE TENGAN AGUA
• GENERADORES Y TRANSFORMADORES
• EQUIPOS PARA EL MANTENIMIENTO DE FUNCIONES VITALES
PRECAUCIÓN: PARA REDUCIR EL
RIESGO DE DESCARGA ELÉCTRICA, UTILICE SOLO EN ESPACIOS INTERIORES.
LA UNIDAD DEBERÁ CONECTARSE A UN TOMACORRIENTE DOBLE DE RANURAS PARALELAS CON CONEXIÓN A TIERRA NO SE DEBE USAR CON TOMACORRIENTES DE CIRCUITO DE FALLOS DE CONEXIÓN A TIERRA O CON TOMACORRIENTES CON CONTROLES O LUCES INDICADORAS. PARA REDUCIR EL RIESGO DE INCENDIO O DE DESCARGA ELÉCTRICA, NO UTILICE ESTE DISPOSITIVO CON UN TOMACORRIENTE CUYAS RANURAS NO SE ALINEEN CON LAS CLAVIJAS.
HECHO EN CHINA Este producto es distribuido y tiene garantía de Jasco
Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114, para © 2017 Gibson Innovations Limited. Todos los derechos reservados. Tanto la marca Philips como el emblema de escudo Philips son marcas registradas de Koninklijke Philips N.V. y son utilizadas por Gibson Innovations Ltd. bajo la licencia de Koninklijke Philips N.V.
Este producto cuenta con una garantía limitada de por vida. Visite www.philips.com/support para conocer los detalles de la garantía.
¿Tiene preguntas? Comuníquese al 1-844-816-0320 entre las 7:00 a. m. y las 8:00 p. m. CST (hora central estándar).
Loading...