EN
Additional information about your energy efficient surge protector
Features |
|
|
|
Your energy efficient surge protector is specifically designed to fit within |
|
|
|
your home theater setup. You can conveniently control the on/off of your |
|
|
|
devices in either zone 1 or zone 2 outlets with your remote control. When |
TV |
|
|
switched to the off position, it eliminates the consumption of the stand-by |
|
STB |
|
power to these outlets, bringing energy savings to your fingertips. |
AMP |
||
|
|||
Zone 1 & 2 outlets group your devices by usage. |
|
DVD |
|
|
|
Always on outlets remain on even when other outlets are switched off
– these are ideal for devices which have volatile memory and require constant power. (i.e. cable modems, DVRs , set top boxes, etc)
Remote control turns your devices on/off in zone 1 & zone 2 with the touch of a button.
Cable management clips help eliminate cable clutter.
Zone 2 |
Zone 1 |
Always on
Cable management clips
LED indicators on the front of the unit provide worry-free protection and show that your surge protector functions properly.
Power – (blue) shows that the power is running to your devices.
Protecting – (red) shows that your surge protector is actively
protecting your devices.
Zone 1 & Zone 2 – (green) lights to show that the group of outlets have been switched on.
POWER
ZONE 1 |
ZONE 2 |
PROTECTING
Remote control
Instructions for changing the remote control battery
NOTE: If the remote control device stops working, replace the battery. Step 1 -Turn the unit over and slide open the battery compartment cover.
Step 2 - Remove and dispose of the old battery properly. Do not throw the old battery in the trash.
Step 3 - Insert a new battery and close the compartment cover. Replace ONLY with a 3 volt CR2032 type button cell battery.
|
|
|
|
|
|
|
RF |
|
|
|
|
(1) |
|
ation |
|
FCC ID:Remote |
|
||||
|
|
|
|
OYMSPP5107C |
||||||
|
|
|
15This |
|
|
|
|
Control |
||
|
|
|
Op |
er |
thedevice |
|
|
|
|
|
|
|
|
of |
|
|
|
|
|
||
(2 |
|
Thisfollowing |
two |
isFCC |
complies |
|
|
|
||
in |
)harmful |
|
|
|
|
|
|
|||
This |
|
device |
|
|
Rules. |
with |
|
|
||
|
|
|
|
subject to |
|
|
||||
undinterferterferencedeviceinterferenmayconditions:the |
|
part |
|
|||||||
Ch.esired |
nce |
|
must |
|
not |
|
|
|
|
|
A |
|
|
|
|
|
|
|
|
||
|
|
received,includingany |
|
|
|
|||||
|
|
that |
|
|
|
e,and |
cause |
|
|
|
|
operatio may |
|
accept |
|
|
|
|
|||
|
Made in |
cause |
|
|
|
|
|
|||
|
|
|
China |
|
|
|
|
|
|
NOTE: The remote control with this unit operates on either channel A or channel B frequency. If you have purchased more than one unit, make sure you have two different frequencies (A and B) as indicated by stickers on the bottom of the unit and on the packaging.
Instructions for attaching the base to the surge protector unit
Step 1
Align tabs of the supplied base unit to the slots on the bottom of the surge protector, then snap them into place.
Step 2
Align the cable management clips into the grooves on the base of the unit.
Step 3
Follow the direction of the arrow as indicated and snap the cable management clips into place.
PWR SRG_insert_EN_V1.0
wk10113