Philips EasySense, SNS100CMP, 510651 Quick Installation Manual

Sensors

EasySense

Ceiling-Mount

Philips EasySense Quick Installation Guide

Commercial Product Name Order Code

EasySense Ceiling-Mount Sensor SNS100CMP (510651)

Connection Color

White Neutral
Black Line
Green Ground
Purple SR+
Brown SR-

Compatible LED Drivers

Sensor Part Number

Driver Model Number Description

XI040C110V054VPT1 Xitanium 40W 0.1-1.1A 27-54V 120-277V SR

XI075C200V054VPT1 Xitanium 75W 0.1-2.0A 27-54V 120-277V SR

Specications available at www.philips.com/XitaniumSR.

Wiring Diagram

XITANIUM SR

LED DRIVER

LED+
LED+

LED-

LED-

RSET2
SGND

NFC ANTENNA

SR-

Connectors

SR+

RED

WHITE

LINE
NEUTRAL

GROUND

NC

36-inch 18AWG solid lead wires in
plenum-rated jacket from sensor stripped
to 3/8". Connect white wire to brown (SR-)
and red wire to purple (SR+) on driver.
Four drivers per sensor maximum.
Polarity must be maintained.

EASYSENSE

Electrical Information

Input Voltage Powered by SR driver low-voltage interface
Current Consumption 13mA
Nominal Power Consumption 200mW
Standby Power < 1 W on luminaire level, including driver standby power

Occupancy Sensing

Type Passive infrared (PIR)
Enable/Disable Default enabled
Detection O/Auto-on; Red LED indicates “on”
Hold Time 1 - 120 minutes
Viewing Angle X=72°, Y = 86° ( See detection pattern)
Background Light Level O or 5-100%
Prolong Time 0 minutes - innity
Grace Fading 0-25 sec
Response Time/Fading to Switch On/O 0.7Sec

Daylight Sensing

Enable/Disable Default enabled
Auto-calibration Upon power-up
Viewing Angle 40° (half value sensitivity); 2% cut-o point at 75°
Task Tuning
Full Light Setting 5-100%

Environment & Approbation

Operating Ambient Temperature Range 0°C to 55°C
Operating Humidity 0 – 95% non condensing
Storage Temperature -25°C to 85°C
Storage Humidity 0-95% non condensing
Max Case Temperature (Tcase) 55°C
Agency Approbations UL, CSA; Tested and approved for use in plenums; FCC ID:

2AF2N-SNS100; IC: 20659-SNS100

Certication California Title 20
Limited Warranty 5 years
Digital Interface Xitanium SR

Other

Status Indicators Red, Yellow. Yellow LED on: Vacancy & Sensor is functional;

Red LED on: Motion is detected

No. Drivers per Sensor Four drivers per sensor maximum; Wiring polarity must be maintained
Field Conguration via NFC, parameters set via Philips Field Apps

© 2016 Philips Lighting Holding B.V. All rights reserved.
Philips reserves the right to make changes in specications
and/or to discontinue any product at any time without notice
or obligation and will not be liable for any consequences
resulting from the use of this publication.
philips.com/easysense

Philips Lighting North America Corporation
10275 W. Higgins Road, Rosemont IL 60018
Tel: [phone] Fax: [phone]
Customer/Technical Service: 800-372-3331
OEM Support: 866-915-5886

Philips Lighting Canada Ltd.
281 Hillmount Rd, Markham, ON, Canada L6C 2S3
Tel. [phone]

PLt-1621QG_EasySenseCMP QIG 02/16 page 1 of 2
Document #: 4435 290 61451 REV. A

Operation and Conguration via Mobile App

EasySense operates immediately upon installation and energization without further commissioning. If changes from
default settings are desired, EasySense can be congured via an app through NFC embedded within the sensor.
The “Philips eld app” can be accessed on the Google Play Store. For a complete description of the features and default
settings—as well as details on the app and recommended Android phones—refer to www.philips.com/easysense.

FCC and IC

This device complies with part 15 of the FCC rules for the United States and Industry Canada (IC) license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Any
changes or modications not expressly approved by Philips could void the user’s authority to operate this equipment.
This product is intended for commercial use only.

Ce dispositif est conforme à la partie 15 des règles de la Federal Communications Commission (FCC) des États-Unis et
d’Industrie Canada (IC) exempts de licence RSS norme(s). Son fonctionnement est assujetti aux deux conditions suivantes
: (1) Ce dispositif ne doit pas provoquer de brouillage préjudiciable, et (2) il doit accepter tout brouillage reçu, y compris
le brouillage pouvant entraîner un mauvais fonctionnement. Tous les changements ou modications non expressément
approuvés par Philips, sont susceptibles d’annuler le droit de l’utilisateur à se servir de cet équipement. Ce produit est
exclusivement destiné à un usage commercial.

Connection Color

Red LED+
Blue LED­Orange RSET2
Green SGND

Sensor Dimensions (in/mm) Installation

Conguring Sensor Parameters

Step 1: Drill 2.5-inch hole in ceiling. It may be
more practical to remove the ceiling tile and
drill from the backside depending on material.

Step 3: Compress spring clips on sensor and
insert into ceiling hole.

Step 5: Connect the wires from the sensor to the LED Driver in the xture. Connect the white
wire from the sensor to the brown (SR-) terminal on the driver. Connect the red wire from the
sensor to the purple (SR+) terminal on the driver. Follow xture manufacturer’s instructions for
accessing the driver.

Note: Up to (4) drivers maximum can be connected to (1) EasySense. Polarity must be maintained.

EasySense operates upon energization with
no further commissioning. See sensor
datasheet for sensor presets and parameters
that can be changed during installation.
Refer to “Operation and Conguration via
Mobile App” on last page for further details.

Step 2: Feed wires from sensor into ceiling
hole. Wire length provided is 36-inches.
Cable jacket provided is plenum-rated.
Add additional wire length if necessary
(18AWG solid wire recommended).

Step 4: Sensor will clamp into place. Turn
sensor to appropriate position.

2.034 [51.65] REF.

Ø 2.500 [63.50] REF.

Ø 2.835 [72.00] REF.

3.193 [81.09] REF.

Note: Remove power from fixtures/drivers before performing any electrical work.