Philips SHB4405, SHB4305 User Manual

SHB4405

Flite

User manual

Register your product and get support at

www.philips.com/support

1EN

Contents

1 Important safety instructions 2

Hearing Safety 2
General information 2

2 Your Bluetooth wireless

headphones 3

What's in the box 3
Other devices 3
Overview of your Bluetooth

wireless headphones 3

3 Get started 4

Charge your headphones 4
Pair the headphones with your

mobile phone 4

4 Use your headphones 5

Connect the headphones to a

Bluetooth device 5
Manage your calls and music 5
Wear your headset 6

5 Technical data 7

6 Notice 8

Notice of compliance 8
Disposal of your old product

and battery 9
Trademarks 9

7 Frequently asked questions 10

2

EN

1 Important

safety
instructions

Hearing Safety

Danger

• To avoid hearing damage, limit the time you

use headphones at high volume and set
the volume to a safe level. The louder the
volume, the shorter the safe listening time is.

Be sure to observe the following
guidelines when using your headset.

• Listen at reasonable volumes for
reasonable periods of time.

• Be careful not to adjust the
volume continuously upwards as
your hearing adapts.

• Do not turn up the volume so high
that you can’t hear what’s around
you.

• You should use caution or
temporarily discontinue use in
potentially hazardous situations.

• Excessive sound pressure from
earphones and headphones can
cause hearing loss.

• Using headphones with both
ears covered while driving is not
recommended and may be illegal
in some areas while driving.

• For your safety, avoid distractions
from music or phone calls while

in trac or other potentially
dangerous environments.

General information

To avoid damage or malfunction:

Caution

• Do not expose headphones to excessive

heat.

• Do not drop your headphones.

• Headphones shall not be exposed to

dripping or splashing.

• Do not allow your headphones to be

submerged in water.

• Do not use any cleaning agents containing

alcohol, ammonia, benzene, or abrasives.

• If cleaning is required use a soft cloth,

if necessary dampened with a minimum
amount of water or diluted mild soap, to
clean the product.

• The integrated battery shall not be exposed

to excessive heat such as sunshine, re or
the like.

• Danger of explosion if battery is incorrectly

replaced. Replace only with the same or
equivalent type.

About operating and storage
temperatures and humidity

• Operate or store in a place where
temperature is between 0ºC
(32ºF) and 55ºC (131ºF) (up to
90% relative humidity.

• Battery life may be shorter in high
or low temperature conditions.

3EN

2 Your

Bluetooth
wireless
headphones

Congratulations on your purchase, and
welcome to Philips! To fully benet
from the support that Philips oers,
register your product at www.philips.
com/welcome.
With this Philips wireless headphones,
you can:

• enjoy convenient wireless
handsfree calls;

• enjoy and control wireless music;

• switch between calls and music.

What's in the box

Philips Bluetooth wireless
headphones SHB4405

USB charging cable (for charging only)

Quick start guide

Other devices

A mobile phone or device (e.g.
notebook, PDA, Bluetooth adapters,
MP3 players etc) which supports
Bluetooth and is compatible to the
headphones (see “Technical data” on
page 7).

Overview of your
Bluetooth wireless
headphones

a Microphone
b LED indicator
c

On/o, music/call control button

d Micro USB charging slot
e Volume/Track control button

3

1

2

5

4

4

EN

3 Get started

Charge your headphones

Warning

• Only charge with a certified USB adapter

DC 5V/0.5A.

Note

• Before you use your headphones for the

rst time, charge the battery for 5 hours for
optimum battery capacity and lifetime.

• Use only the original USB charging cable to

avoid any damage.

• Finish your call before charging the

headphones, as connecting the headphones
for charging will power the headphones o.

Connect the supplied USB charging
cable to:

• the micro USB charging slot on

the headphones and;

• the certied charger/USB port

of a computer.

» LED turns red during charging

and turns o when the
headphones are fully charged.

Tip

• Normally, a full charge takes 2 hours.

Pair the headphones
with your mobile phone

Before you use the headphones
with your mobile phone for the rst
time, pair it with a mobile phone.
A successful pairing establishes a

unique encrypted link between the
headphones and mobile phone. The
headphones store the last 4 devices
in the memory. If you try to pair more
than 4 devices, the earliest paired
device is replaced by the new one.

1

Make sure that the headphones
are fully charged and turned o.

2

Press and hold for 6 seconds
until the blue and red LED ashes
alternately.
» The headphones remain in

pairing mode for 5 minutes.

3

Make sure that the mobile phone
is turned on and its Bluetooth
feature is activated.

4

Pair the headphones with the
mobile phone. For detailed
information, refer to the user

manual of your mobile phone.
The following example shows you
how to pair the headphones with your
mobile phone.

1

Activate the Bluetooth feature of

your mobile phone, select Philips

SHB4405.

2

Enter the headset password

"0000" (4 zeros) if prompted. For

those mobile phones featuring

Bluetooth 3.0 or higher, no need

to enter a password.

SHB4405

5EN

4 Use your

headphones

Connect the
headphones to a
Bluetooth device

1

Make sure that the mobile phone
is turned on and its Bluetooth
feature is activated.

2

Press and hold to turn the
headphones on.

» The blue LED ashes for every

8 seconds.

» The headphones are

reconnected to the
last connected mobile
phone/Bluetooth device
automatically. If the last one is
not available, the headphones
try to reconnect to the second
last connected device.

Tip

• If you turn on the mobile phone/Bluetooth

device or activate the Bluetooth feature
after turning on the headphones, you have
to reconnect the headphones and mobile
phone/Bluetooth device manually.

Note

• If the headphones fail to connect to any

Bluetooth device within range in 5 minutes,
it will switch o automatically to save the
battery life.

Manage your calls and
music

On/o

Task Button Operation

Turn the
headphones
on.

Press and
hold for 2
seconds.

Turn the
headphones
o.

Press and
hold for 4
seconds.

» The

red
LED is
on and
fades
out.

Music control

Task Button Operation

Play or pause
music.

Press once.

Adjust volume. +/- Press once.
Skip forward. + Long press.
Skip

backward.

- Long press.

Call control

Task Button Operation

Pick up/hang
up a call.

Press once.

» 1 beep.

Reject an
incoming call.

Press and
hold for 2
seconds.

» 1 beep.

Switch caller
during a call.

Press twice.

» 1 beep.

Mute/unmute
the microphone
in a call.

+ and - Press once.

» 1 beep.

6

EN

Other headphones indicator status

Headphones
status

Indicator

The headphones
are connected
to a Bluetooth
device, while the
headphones in
standby mode
or while you
are listening to
music.

The blue LED
ashes for every 8
seconds.

The headphones
are ready for
pairing.

The LED ashes
blue and red
alternately.

The headphones
are on but not
connected to a
Bluetooth device.

The blue LED
ashes quickly.
If no connection
can be made,
the headphones
will turn itself o
within 5 minutes.

Low battery level. The red LED

ashes 3 times for
every 10 seconds
until it is out of
power.

Battery is fully
charged.

The red LED is o.

Wear your headset

Adjust the headband to t your head.

7EN

5 Technical

data

• Music time/talk time: up to 9 hours

• Standby time: up to 300 hours

• Normal time for a full charge: 2
hours

• Rechargeable lithium polymer
battery (200 mAh)

• Bluetooth 4.1, Bluetooth mono
support (Headset Prole - HSP,
Hands-Free Prole - HFP),
Bluetooth stereo supported
(Advanced Audio Distribution
Prole - A2DP; Audio Video
Remote Control Prole - AVRCP)

• Operating range: Up to 10 meters
(33 feet)

• Auto power o

Note

• Specications are subject to change without

notice.

8

EN

6 Notice

Notice of compliance

Notice for US

This set complies with the FCC rules,
Part 15 and with 21 CFR 1040.10.
Operation is subject to the following
two conditions:

a This device may not cause harmful

interference, and

b This device must accept any

interference received, including
interference that may cause
undesired operation.

FCC rules

This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant
to part 15 of the FCC Rules. These
limits are designed to provide
reasonable protection against
harmful interference in a residential
installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
However, there is no guarantee
that interference will not occur
in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment o and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:

• Relocate the receiving antenna.

• Increase the separation between
equipment and receiver.

• Connect the equipment into
an outlet on a circuit dierent
from that to which the receiver is
connected.

• Consult the dealer or an
experienced radio/TV technician
for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC
radiation exposure limits set forth for
an uncontrolled environment. This
equipment should be installed and
operated with a minimum distance of
20cm between the radiator and your
body. This transmitter must not be
co-located or operated in conjunction
with any other antenna or transmitter.
Warning: Changes or modications
made to this equipment not expressly
approved by Gibson Innovations may
void the FCC authorization to operate
this equipment.
Model number: SHB4405
Trade Name: Philips
Responsible party: Gibson Innovations
USA Inc. P.O.Box 100572 Nashville TN
37224

Notice for Canada:

This device complies with Industry
Canada licence-exempt RSS
standard(s). Operation is subject
to the following two conditions: (1)
this device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
This Class B digital apparatus
complies with Canadian ICES-003.
IC Radiation Exposure Statement:
This equipment complies with Canada
radiation exposure limits set forth for
uncontrolled environments.
This transmitter must not be co­located or operating in conjunction
with any other antenna or transmitter.

9EN

Disposal of your old
product and battery

Your product is designed and
manufactured with high quality
materials and components, which can
be recycled and reused.

This product may contain lead
and mercury. Disposal of these
materials may be regulated due to
environmental considerations. For
disposal or recycling information,
please contact your local authorities
or visit www.recycle.philips.com.
This product contains non-removable
batteries:

• Do not incinerate. Batteries may
explode if overheated.

• For disposal or recycling
information, please contact your
local authorities or visit www.
recycle.philips.com.

Trademarks

Bluetooth

The Bluetooth word mark and logos
are owned by the Bluetooth SIG, Inc.
and any use of such marks by Gibson
Innovations is under license.

10

EN

7 Frequently

asked
questions

My Bluetooth headphones do not
switch on.

The battery level is low. Charge the
headphones.

I cannot pair my Bluetooth
headphones with a mobile phone.

The Bluetooth is disabled. Enable
the Bluetooth feature on your mobile
phone and turn on the mobile phone
before you turn on the headphones.

Pairing does not work.

Make sure the headphones are in
pairing mode.

• Follow the steps described in
this user manual (see “Pair the
headphones with your mobile
phone” on page 4).

• Make sure that the LED light
ashes blue and red alternately
before you release . Do not
stop holding the button if you see
the red LED only.

The mobile phone cannot nd the
headphones.

• The headphones may be

connected to a previously paired
device. Turn o the connected
device or move it out of range.

• Pairing may have been reset or the

headphones have been previously
paired with another device. Pair
the headphones with the mobile
phone again as described in
the user manual (see “Pair the
headphones with your mobile
phone” on page 4).

My Bluetooth headphones are
connected to a Bluetooth stereo
enabled mobile phone, but music only
plays on the mobile phone speaker.

Refer to the user manual of your
mobile phone. Select to listen to
music through the headphones.

The audio quality is poor and crackling
noise can be heard.

The Bluetooth device is out of range.
Reduce the distance between your
headphones and Bluetooth device, or
remove obstacles between them.

The audio quality is poor when
streaming from the mobile phone is
very slow, or audio streaming does not
work at all.

Make sure your mobile phone not only
supports (mono) HSP/HFP but also
supports A2DP (see “Technical data”
on page 7).

I hear but cannot control music on my
Bluetooth device (e.g. play/pause/skip
forward/backward).

Make sure the Bluetooth audio source
supports AVRCP (see “Technical data”
on page 7).

For further support, visit www.philips.
com/support.

BC

2016 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility
of Gibson Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in
relation to this product.
Philips and the Philips’ Shield Emblem are registered
trademarks of Koninklijke Philips N.V.

UM_SHB4405_27_EN_V1.0
WK1630