Philips Avent Milk Storage container
Philips Avent recipiente para almacenar leche
Philips Avent recipiente de armazenamento de leite
Philips Avent trainer cup
Philips Avent vasito de entrenamiento
Philips Avent copo de treinamento
Philips Avent breast pump
Philips Avent extractor de leche maternal
Philips Avent extrator de leite
ENGLISH
For your child‘s safety
and health
WARNING!
- Keep the cap away from
children to avoid suocation.
- Always use this product with
adult supervision.
- Never use feeding teats as a
soother, to prevent choking
hazard.
- Continuous and prolonged
sucking of uids will cause
tooth decay.
- Always check food
temperature before feeding.
- It is not recommended to
use a microwave to warm
up baby‘s food or drinks.
Microwaves might alter
the quality of food/drinks
and destroy some valuable
nutrients and may produce
localized high temperatures.
Therefore, take extra care
if and when you heat up
food in a microwave.When
heating up liquid or food in
the microwave, only place
the container without screw
ring, AirFree™ vent insert, teat
and cap. Always stir heated
food to ensure even heat
distribution and check the
temperature before serving.
- Keep all components not
in use out of the reach of
children.
- Do not allow child to play
with small parts or walk/run
while using bottles or cups.
- Do not place in a heated
oven.
- Drinks other than milk and
water, such as fruit juices and
avored sugary drinks are not
recommended. If used, they
should be well diluted and
only used for limited periods,
not constantly sipped.
- Expressed breast milk can
be stored in sterilized Philips
Avent bottles/containers
in the refrigerator for up to
48 hours (not in the door)
or in the freezer for up to
3 months. Never refreeze
breast milk or add fresh
breast milk to already frozen
milk.
- Always discard any breast
milk that is left over at the
end of a feed.
- Do not use abrasive cleaning
agents or anti-bacterial
cleaners. Do not place
components directly on
surfaces that have been
cleaned with anti-bacterial
cleaners.
- Plastic material properties
may be aected by sterilizing
and high temperatures. This
can aect the t of the cap.
- Inspect the feeding teat
before use and pull the
feeding teat in all directions.
- Throw away any part at
the rst signs of damage or
weakness.
- Do not alter the product
or parts of it in any way.
This may result in unsafe
functioning of the product.
AirFree™ vent insert
Benet: The AirFree™ vent insert
keeps the teat full of milk during
feeding, even while the bottle is
held horizontally. This supports
an upright feeding position for
your baby in order to reduce air
ingestion. This helps reduce
common feeding issues
including wind and reux (GER).
Assembly: Place the AirFree™
vent insert in the bottle before
you assemble the screw ring
with teat.
Warning: When you prepare
formula, make sure that all the
formula is fully dissolved to
avoid blocking the AirFree™
vent insert.
Note: Always make sure the
teat is full of milk by turning
the bottle upside down before
feeding your baby. While
feeding, make sure that the
AirFree™ vent insert points
upwards, in line with your baby‘s
nose (see image).
Compatibility: The AirFree™
vent insert only works with
4 oz/125 ml, 9 oz/260 ml and
11 oz/330 ml Philips Avent
Anti-colic bottle and Classic+
bottles, teat and screw ring.
The AirFree™ vent insert is
compatible with the (I/II/III)
v
ariable ow teat and the
Natural bottle range.
Note: When using an 11 oz/330 ml
bottle, the AirFree™ vent insert
insert will keep the teat full of
milk but it could be that you see
fewer air bubbles.
Philips Avent Anti-colic bottles
and Classic+ bottles can also be
used without the AirFree™ vent
insert.
not
Before rst and every use
Disassemble all parts and clean
them in warm soapy water and
rinse them thoroughly. Sterilize
the parts in boiling water for
5 minutes or by using a Philips
Avent sterilizer. This is to ensure
hygiene. During sterilizing in
boiling water, make sure that
the pan contains enough water
and prevent the bottle or other
parts from touching the side
of the pan. This can cause
irreversible product deformation,
defect or damage that Philips
cannot be held liable for. Make
sure that you wash your hands
thoroughly and that the surfaces
are clean before contact with
sterilized parts. Place all bottle
parts on a clean paper towel
or on a clean drying rack and
allow them to air dry. Excessive
concentration of detergents
may eventually cause plastic
components to crack. Should
this occur, replace immediately.
This product is dishwasher safe
- food colourings may discolour
parts. Clean and sterilize all parts
before each use. For hygiene
reasons, we recommend
replacing teats after 3 months.
Assembly
When you assemble the bottle,
make sure you place the cap
vertically onto the bottle so that
the teat sits upright (see image
for more details). The teat is
easier to assemble if you wriggle
it upwards instead of pulling it
up in a straight line.
Maintenance teat and
AirFree™ vent insert
Do not leave a feeding teat and/
or AirFree™ vent insert in direct
sunlight or heat, or leave in
disinfectant (‘sterilizing solution’)
for longer than recommended, as
this may weaken the parts. Keep
parts in dry, covered container.
Choosing the right teat
for your baby
The Philips Avent teats are
separately available with
dierent ow rates to help
your baby with drinking.
Over time you can change
the teat accommodating the
individual needs of your baby.
Philips Avent teats are clearly
numbered on the side to
indicate ow rate. Make sure
you use a teat with the correct
ow rate when you feed your
baby. Use a lower ow rate if
your baby chokes, is leaking
milk or has trouble adjusting
to the drinking speed. Use a
higher ow rate if your baby
falls asleep during feeding, gets
frustrated or when feeding takes
a very long time. These Philips
Avent teats can be used on the
Philips Avent feeding bottle and
Philips Avent storage cups.
Loading...
+ 10 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.