Philips SCF356/00 User manual

SCF356

User manual

用户手册

4213.354.3669.4

使用本产品之前，请仔细阅读本用户手册保留备用

2 3 4 5

22 23 24 25

10 11 12 13

14 15 16 17

18 19 20 21

7 8 9

ENGLISH 6

繁體中文 17

简体中文 26

SCF356

ENGLISH

General description (Fig. 1)

1 Baby bottle warmer 2 Progress indicator 3 Settings and on/off knob 4 Defrost setting 5 Milk warming setting 1 6 Milk warming setting 2 7 Milk warming setting 3 8 Baby food warming setting 9 On/off button

Important

To fully benet from the support that Philips offers, register your appliance at www.philips.com/welcome. Read this user manual carefully before you use the baby bottle warmer

and save it for future reference.

Danger

- Never immerse the appliance in water or any other liquid, nor rinse it under the tap.

Warning

- Only use the appliance indoors.

- This appliances can be used by persons with reduced physical,

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

- Cleaning and user maintenance shall not be made by children.

- Care must be taken to ensure that children do not play with the appliance.

- This appliance shall not be used by children. Keep the appliance and its

cord out of reach of children.

- Do not immerse the cord, plug or appliance in water or any other liquid.

- Do not let the mains cord hang over the edge of a table or worktop.

Excess cord can be stored in the base of the baby bottle warmer to ensure stability of the appliance.

- Keep the mains cord away from hot surfaces.

ENGLISH 7

- Only connect the appliance to an earthed wall socket. Always make sure that the plug is inserted into the wall socket properly.

- Check if the voltage indicated on the bottom of the appliance corresponds to the local mains voltage before you connect the appliance.

- If you need to use an extension cord, make sure it is an earthed extension cord with a rating of at least 13 amperes.

- Do not use the appliance if the plug, the mains cord or the appliance itself is damaged. If the mains cord is damaged, you must have it replaced by Philips, a service centre authorised by Philips or similarly qualied persons in order to avoid a hazard.

- Do not place the appliance on or near a hot gas or electric cooker, or in a heated oven.

- Do not preheat the appliance.

- Always place a fully assembled bottle with cap in the baby bottle warmer before you add water.

- Make sure you add water before you switch on the baby bottle warmer.

- Hot water can cause serious burns. Be careful when the baby bottle

warmer contains hot water.

- The accessible surfaces of the appliance may become hot during use.

- Do not move the appliance when it contains hot water.

- Always check the food temperature before you feed your child.

Caution

- This appliance is intended to be used in household and similar applications such as farm houses, bed and breakfast type environments, staff kitchen areas in shops, ofces and other working environments, and by clients in hotels, motels and other residential type environments.

- Unplug the appliance when it is not in use.

- Store any excess mains cord in the base to ensure stability of the baby bottle warmer.

- Let the appliance cool down before you clean it.

- Follow the descaling instructions to avoid irreparable damage.

- Do not try to open or repair the appliance yourself. You can contact

the Philips Consumer Care Centre in your country (see

www.philips.com/support).

- The food should not be heated for too long.

ENGLISH8

- Only use the appliance as described in the user manual to avoid potential injury due to misuse.

- The surface of the heating element is subject to residual heat after use.

You can nd the production date code YYWW in the cord storage compartment in the base of the bottle warmer.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic elds.

Using the baby bottle warmer

With this baby bottle warmer, you can safely warm and defrost milk in Philips Avent feeding bottles and milk or baby food in containers. The baby bottle warmer helps to preserve the valuable nutrients and vitamins in breast milk because it never overheats the milk. If milk becomes too warm, nutrients and vitamins are damaged. To help preser ve the quality of your breast milk, it is important to heat the milk in a safe and controlled way. The baby bottle warmer is designed to warm gently and evenly and to avoid hot spots, as the milk circulates during warming. The built-in sensor tracks and controls the milk temperature, to avoid overheating at all times.

Note: Philips Avent breast milk bags and Philips Avent 2oz/60ml bottles cannot be used in this baby bottle warmer.

Explanation of settings

- You can choose between the following settings: (Fig. 2)

- Defrost setting: To defrost a bottle or container with frozen milk or

frozen baby food. No warming occurs.

- Milk warming settings: Select one of these settings when you want to warm a bottle of milk to a safe temperature. Setting 2 warms your milk to approximately body temperature. Setting 1 warms your milk to a slightly lower temperature and setting 3 warms your milk to a slightly higher temperature.

- Baby food warming setting: Select this setting when you want to warm a container or jar with baby food.

ENGLISH 9

Using the baby bottle warmer to warm milk

1 Put the mains plug in the wall socket (Fig. 3).

2 Place a bottle centrally in the baby bottle warmer (Fig. 4).

Note: To warm milk in a milk storage container, follow the same steps as indicated for warming milk in a bottle.

3 Fill the baby bottle warmer with the same amount of drinking

water as the amount of milk you want to warm up (for example, to warm up 125ml/4oz of milk, you need to use 125ml/4oz of drinking water). If you want to heat up a large amount of milk (>180ml/6oz), the maximum water level is approximately 1cm/0.4 inches under the rim of the baby bottle warmer (which corresponds to adding 160ml/4.5oz of drinking water). An accurate water level ensures correct warming performance. (Fig. 5)

4 Select the desired setting (Fig. 6).

Note: Experience teaches that babies may have a preference for a specic

milk temperature. This can be due to personal preference or external factors (e.g. environment temperature). All three settings ensure that the milk is warmed to a safe temperature which is comfortable for your child and helps to preserve the nutrients and vitamins in the milk.

5 Press the on/off button to switch on the appliance. The light in the

button lights up to indicate that the baby bottle warmer is on (Fig. 7).

Note: The baby bottle warmer starts warming up right after you press the button.

6 Theprogressindicatorstartstollupgraduallywithwhitelightto

show the progress of the milk warming process (Fig. 8).

Note: The progress indicator shows the progress of the milk warming process.

The progress indicator starts ashing when the appliance is on. When the rst

warming phase has been completed, the bottom segment lights up continuously

and the next segment starts ashing to show that the second warming phase is

in progress. These steps continue until the third warming phase has been completed. Then the entire progress indicator lights up continuously.

ENGLISH10

Note: During the warming process, the milk circulates to ensure even warming. It takes about 10 minutes to warm 90ml/3oz of room-temperature milk. It takes slightly longer to warm cold milk or a large amount of milk.

Caution: Do not take the bottle out of the baby bottle warmer while

theprogressindicatorisashing.

7 When the entire progress indicator lights up continuously, the milk

has reached the set temperature.

- When the milk is warm, you can either take the bottle out of the baby bottle warmer to feed your baby right away (see section ‘Feeding your baby immediately’) or you can keep it warm in the baby bottle warmer (see section ‘Keeping milk warm’).

Increasing the milk temperature

1 If you want the milk to be warmer, you can increase the milk

temperature gradually after it is ready by switching to milk warming setting 3 and leaving the bottle in the appliance at the keep-warm mode (Fig. 9).

2 If you just switched off the baby bottle warmer or if it just switched

off automatically, switch it back on without removing the warm water from it, and follow the above step (Fig. 10).

3 The baby bottle warmer switches off automatically after 20 minutes

of keep-warm mode (Fig. 11).

Feeding your baby immediately

1 Press the on/off button to switch off the appliance and take out the

milk bottle (Fig. 10).

2 Always check the temperature of the milk before you feed your baby.

Gently swirl the milk in the bottle and check the temperature of the milk by sprinkling a few drops on the inside of your wrist (Fig. 12).

3 Unplug the appliance and empty the baby bottle warmer (Fig. 13).

ENGLISH 11

Keeping milk warm

1 When the milk has reached the desired temperature, the baby

bottle warmer automatically switches to the keep-warm mode. In this mode, the milk is kept at the set temperature for 20 minutes (Fig. 14).

2 The baby bottle warmer switches off automatically after

20 minutes. The progress indicator switches off to indicate that the milk is not kept at the desired temperature anymore (Fig. 11).

Note: If you want to feed your baby with milk at the set temperature, you need to take the milk bottle out of the baby bottle warmer and feed it to your baby right after the baby bottle warmer switches off, otherwise the milk cools down.

Note: You cannot prolong the keep-warm mode of the baby bottle warmer for more than 20 minutes.

Caution: It is not recommended to reheat breast milk twice, as bacteria start to develop in the milk.

3 Always check the temperature of the milk before you feed your

baby. Gently swirl the milk in the bottle or milk storage container and check the temperature of the milk by sprinkling a few drops on the inside of your wrist (Fig. 12).

4 Unplug the appliance and empty the baby bottle warmer (Fig. 13).

Re-using the baby bottle warmer right away for another bottle

If you want to heat up another bottle right away, let the baby bottle warmer cool down for a few minutes. To speed up this process, ll the baby bottle warmer with fresh cold water. When you switch on the baby bottle warmer, the progress indicator starts ashing from bottom to top to indicate that the appliance is heating up again.

Note: If the progress indicator is on but does not ash, the baby bottle

warmer is still too warm to heat up another bottle. Please switch off the baby

ENGLISH12

bottle warmer, let it cool down for a few minutes and make sure you ll it

with fresh cold water.

Using the baby bottle warmer to warm baby food

1 Put the mains plug in the wall socket (Fig. 3).

2 Place a baby food container or jar centrally in the baby bottle

warmer (Fig. 15).

Note: You can leave off the lid of the food container or jar, so you can stir the baby food during heating.

3 Fill the baby bottle warmer with the same amount of drinking

water as the amount of baby food you want to warm up (for example, to warm up 125ml/4oz of baby food, you need to use 125ml/4oz of drinking water). If you want to warm up a large amount of baby food, the maximum water level is approximately 1cm/0.4 inches under the rim of the baby bottle warmer (which corresponds to adding 160ml/4.5oz of drinking water). An accurate water level ensures correct warming performance. (Fig. 16)

4 Select the baby food warming setting (Fig. 17).

5 Press the on/off button to switch on the appliance. The light in the

progress indicator shows that the baby bottle warmer is on (Fig. 18).

Note: The baby bottle warmer starts warming up right after you press the button. Due to the large variety of baby food consistencies, it is not possible for the appliance to detect exactly how long the baby food should be warmed.

6 Theprogressindicatorstartstollgraduallywithwhitelightto

show the progress of the warming process. During the warming process, do not take the jar or container out of the baby bottle warmer but stir the baby food while the jar or container is still in the baby bottle warmer (Fig. 19).

Note: You can start stirring the baby food once the second segment of the progress indicator lights up continuously. Stirring before this moment is not effective as the temperature of the baby food is still too low.

ENGLISH 13

Caution: Do not take the food container or jar out of the baby bottle warmer during warming.

7 When the entire progress indicator lights up continuously, the baby

food has reached the desired temperature.

Note: Due to the large variety of baby food consistencies, it is strongly recommended that you continuously stir the baby food and check its temperature while it is heating up for an optimal result.

- When the baby food is warm, you can either take the baby food container or jar out of the baby bottle warmer to feed your baby right away (see section ‘Feeding your baby immediately’) or you can keep it warm in the baby bottle warmer (see section ‘Keeping baby

food warm’).

Increasing the baby food temperature

1 Always taste the baby food after warming it up to make sure it is

not too hot. If you want the baby food to be warmer, put the container back into the baby bottle warmer and leave it in there at the keep warm-mode for some time. Keep stirring the baby food (Fig. 15).

2 If you just switched off the baby bottle warmer or if it just switched

off automatically, switch it back on without removing the warm water from it, and follow the above step (Fig. 18).

3 The baby bottle warmer switches off automatically after 20 minutes

of keep-warm mode (Fig. 20).

Feeding your baby immediately

1 Press the on/off button to switch off the appliance and take out the

baby food container or jar (Fig. 18).

2 After warming, taste the baby food to ensure it is not too hot (Fig. 21).

3 Unplug the appliance and empty the baby bottle warmer (Fig. 13).

ENGLISH14

Keeping baby food warm

1 When the baby food has reached the desired temperature, the

baby bottle warmer automatically switches to the keep-warm mode. In this mode, the baby food is kept at the desired temperature for 20 minutes (Fig. 22).

2 The baby bottle warmer switches off automatically after

20 minutes. The progress indicator switches off to indicate that the baby food is not kept at the desired temperature anymore (Fig. 20).

Note: If you want to feed your baby with the baby food at the set temperature, you need to take the baby food out of the baby bottle warmer and feed it to your baby right after the baby bottle warmer switches off. If you do not do this, the baby food slowly cools down.

Note: You cannot prolong the keep-warm mode of the baby bottle warmer for more than 20 minutes.

3 Always check the temperature of the baby food before you feed

your baby. Gently stir the baby food in the baby food container or jar and taste the baby food to ensure it is not too hot (Fig. 21).

4 Unplug the appliance and empty the baby bottle warmer (Fig. 13).

Re-using the baby bottle warmer right away for another container of baby food

If you want to heat up another container or jar with baby food right away, let the baby bottle warmer cool down for a few minutes. To speed up this process, ll the baby bottle warmer with fresh cold water. When you switch on the baby bottle warmer, the progress indicator starts ashing from bottom to top to indicate that the appliance is heating up again.

Note: If the progress indicator is on but does not ash, the baby bottle

warmer is still too warm to heat up another container or jar with baby food. Please switch off the baby bottle warmer, let it cool down for a few minutes

and make sure you ll it with fresh cold water.

+ 26 hidden pages