Philips SC2001 User Manual [de]

Register your product and get support at
www.philips.com/welcome
SC2001/01
small illustrations:
incl. numbers
2
ENGLISH 6 DEUTSCH 28 ESPAÑOL 52 FRANÇAIS 76 ITALIANO 100 NEDERLANDS 124 PORTUGUÊS 148
6

ENGLISH

Table of contents
Introduction 7
Benets 7
Intense Pulsed Light (IPL) technology for home use 7 Effective hair regrowth prevention for everyday smoothness 7 Gentle treatment, even on sensitive body areas 8
Cordless operation for maximum freedom and exibility 8
Lamp does not require replacement 8
How Philips’ Intense Pulsed Light technology works 8
Hair growth 8
Working principle 8 General description 8 Important 9
Danger 9 Warning 9
To prevent damage: 10
Caution 10
Keep the following things in mind to avoid compromising
the lifetime of your Philips Lumea: 10
For whom is Philips Lumea not suitable? 10
Contraindications 10
Never use the appliance if you are pregnant or breast feeding. 10
Never use the appliance if you have an unsuitable skin and/or hair
colour, i.e.: 10
Never use the appliance if you suffer from any of the diseases listed
below, i.e.: 11
Never use the appliance if you take any of the medications
listed below, i.e.: 11
Never use the appliance on the following areas: 11
Never use the appliance on sunburnt, recently tanned
(last 48 hours) or fake-tanned skin: 12
Electromagnetic elds (EMF) 12
Charging 12 Preparing for use 13
Preparing treatment areas 13
Setting the light intensity 13
Recommended light intensities (1-5) 14
Important 14
Tanning advice 14 Using the appliance 15
First use and skin test 15 Subsequent use 16 Guidelines for treatment 18
Average treatment time 18
Using the appliance on the legs 18
Using the appliance in the bikini area 19
Using the appliance on the underarms 19
How to achieve optimal results 19
Maintenance phase 19
Possible side effects and skin reactions 19
After use 20 Cleaning and maintenance 20
ENGLISH 7
Storage 21 Replacement 21
Replacement parts 21 Environment 22
Removing the rechargeable batteries 22 Guarantee and service 23
Technical specications 23
Troubleshooting 24
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet
from the support that Philips offers, register your product at www.philips. com/lumea. Light-based hair removal is one of the most effective methods to treat unwanted body hair with longer-lasting results. It is different from
current home hair removal methods because it signicantly reduces
hair regrowth. Philips has been investigating this method together with leading dermatologists for over 10 years. You can now use this innovative technology comfortably in the privacy of your own home, whenever and wherever you want.
This appliance has been specically designed and optimised for use by
women, but can be used by men as well. It is intended for removing body hair on areas mentioned below:
- Underarms
- Arms
- Stomach
- Bikini area
- Legs Do not use Philips Lumea on the face. Philips Lumea is designed for use by one person only. For more information about Philips Lumea, see www.philips.com/lumea. Check our homepage regularly for updates.
Benets
This appliance provides the following benets:
Intense Pulsed Light (IPL) technology for home use
Philips Lumea uses a light-based technology called ‘Intense Pulsed Light’ (IPL). IPL is also used in the professional beauty market for hair removal
and has been in use for the last fteen years. Philips Lumea now brings this
innovative technology to the comfort of your home.
Effective hair regrowth prevention for everyday smoothness
This method provides you with long-lasting hair regrowth prevention and
silky-smooth skin. Our studies have shown a signicant hair reduction
already after two treatments. Optimal results were generally achieved after
four to ve treatments. A reduction in hair density is visible from treatment
to treatment. How fast the effect becomes visible and how long the results last varies from person to person. For more information, see section ‘How to achieve optimal results’ in chapter ‘Using the appliance’.
ENGLISH8
1
Gentle treatment, even on sensitive body areas
Philips Lumea has been developed in close cooperation with leading dermatologists for an effective and gentle treatment, even on the most sensitive body areas.
Cordless operation for maximum freedom and exibility
Because the appliance runs on rechargeable batteries, it is portable and can be used anywhere.
Lamp does not require replacement
Philips Lumea is equipped with a high performance lamp which does
not require replacement. This lamp can generate over 80,000 ashes and
should enable you to continuously maintain results for more than 5 years* while saving money on expensive replacement lamps. *Based on average usage scenario and recommended treatment regime for one user.
How Philips’ Intense Pulsed Light technology works
Hair growth
Hair growth rates differ from person to person, depending on age, metabolism and other factors. However, everyone’s hair normally grows in 3 phases. 1 Growing phase (anagen phase) The hair grows actively from the root. In this phase the concentration of
melanin is highest. Melanin is responsible for the pigmentation of the hair. Melanin concentration is also the determining factor for the efcacy of this
method. Only hairs in the growing phase are susceptible to treatment with light. 2 Degradation phase (catagen phase) Hair growth stops and the root shrinks before the hair sheds. 3 Resting phase (telogen phase) The old hair separates from its hair follicle and sheds. The follicle remains at rest until the biological clock tells it to become active again and grow a new hair.
Working principle
The appliance works by heating up the hair and root beneath the skin. The melanin in the hair and hair root absorbs the released light pulses. The darker the colour of the hair, the more light can be absorbed. This process stimulates the hair to go into the resting phase. The hair now sheds naturally and the hair growth is inhibited. Hairs can take one or two weeks to shed. Optimal hair removal cannot be obtained with a single session, since only hairs in the growing phase are susceptible to treatment with light. During a treatment, hairs on the treated area are usually in different stages of the hair growth cycle. To effectively treat all hairs you have to repeat the treatment every two weeks for a few times.
An integrated optical lter ensures that no UV light reaches the skin
and guarantees that the appliance is safe for the skin.
General description (Fig. 2)
A Light exit window with integrated UV lter B Body Attachment C Metallic frame inside the attachment
ENGLISH 9
D Safety system (safety ring with contact switches) E Flash button F Intensity lights (1- 5) G % Intensity increase button H ^ Intensity decrease button I Charging light and battery low indication J On/off button K ’Ready to ash’ light L Appliance socket M Adapter N Small plug O Air vents
Also included: pouch and cleaning cloth
Important
Read this user manual carefully before you use the appliance and save it for future reference.
Danger
- Water and electricity are a dangerous combination. Do not use this
appliance in wet surroundings (e.g. near a lled bath, a running shower or a lled swimming pool).
- Keep the appliance and the adapter dry.
- If the appliance is broken, do not touch any inner part to avoid
electric shock.
- Never insert any objects into the appliance.
Warning
- This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the
appliance.
- The appliance is not intended for children under the age of 15 years.
Teenagers aged between 15 and 18 years can use the appliance with the consent and/or assistance of their parents or the persons who have parental authority over them. Adults from 19 years and older can use the appliance freely.
- Only charge the appliance with the adapter supplied.
- Do not use the appliance or the adapter if it is damaged.
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
- If the adapter is damaged, always have it replaced with one of the
original type in order to avoid a hazard.
- Do not use the appliance if the UV lter of the light exit window
is broken.
ENGLISH10
To prevent damage:
- Make sure nothing obstructs the air ow through the ventilation slots.
- Never subject the appliance to heavy shocks and do not shake or drop it.
- If you take the appliance from a very cold environment to a very warm
environment or vice versa, wait approximately 3 hours before you use it.
- Store the appliance in the pouch so that it does not become dusty.
- Never leave the appliance unattended when it is switched on. Always
switch off the appliance after use.
- Do not expose the appliance to direct sunlight or UV light for several
hours.
- Do not ash against any other surface than the skin. This can cause
severe damage to the attachment and/or the light exit window. Only
ash when the appliance is in contact with skin.
Caution
- This appliance is only intended for removing unwanted body hair from
areas below the neck. Do not use it for any other purpose.
- Use this appliance only at settings suitable for your skin type. Use at
higher settings than those recommended can increase the risk of skin reactions and side effects.
Keep the following things in mind to avoid compromising the lifetime of your Philips Lumea:
- Do not expose the appliance to temperatures lower than 15°C or
higher than 35°C during use.
- The appliance is equipped with a built-in overheat protection. If the
appliance overheats, it does not ash. Do not switch off the appliance,
but let it cool down for approx. 15 minutes before you continue with your treatment.
- Always return the appliance to a service centre authorised by Philips
for examination or repair. Repair by unqualied people could cause an
extremely hazardous situation for the user.
- Never use the appliance in any of the cases mentioned in the section
‘Contraindications’.
For whom is Philips Lumea not suitable?
Philips Lumea is not designed for everyone. If any of the following is true for you, then this appliance is not suitable for you to use!
Contraindications
Never use the appliance if you are pregnant or breast feeding. Never use the appliance if you have an unsuitable skin and/or
hair colour, i.e.:
- If your natural hair colour in the treatment areas is light blond, white,
grey or red.
- If you are of skin type VI (you rarely or never get sunburnt and you tan
very darkly; your skin colour is brownish black or darker). In this case you run a high risk of developing skin reactions, such as strong redness, burns or discolourations, when you use Philips Lumea.
ENGLISH 11
Never use the appliance if you suffer from any of the diseases listed below, i.e.:
- If you have a skin disease such as active skin cancer, you have a history
of skin cancer or any other localised cancer in the areas to be treated.
- If you have pre-cancerous lesions or multiple atypical moles in the areas
to be treated.
- If you have a history of collagen disorder, including a history of keloid
scar formation or a history of poor wound healing.
- If you have a history of vascular disorder, such as the presence of
varicose veins or vascular ectasia in the areas to be treated.
- If your skin is sensitive to light and easily develops a rash or an
allergic reaction.
- If you have infections, eczema, burns, inammation of hair follicles,
open lacerations, abrasions, herpes simplex, wounds or lesions and haematomas in the areas to be treated.
- If you have had surgery in the areas to be treated.
- If you have epilepsy with ashlight sensitivity.
- If you have diabetes, lupus erythematodes, porphyria or congestive
heart disease.
- If you have any bleeding disorder.
- If you have a history of immunosuppressive disease (including HIV
infection or AIDS).
Never use the appliance if you take any of the medications listed below, i.e.:
- If your skin is currently being treated with or has recently been treated
with Alpha-Hydroxy Acids (AHAs), Beta- Hydroxy Acids (BHAs), topical isotretinoin and azelaic acid.
- If you have taken any form of isotretinoin Accutane
in the last six months.This treatment thins the skin and can therefore make it more susceptible to tears, wounds and irritations.
- If you are on painkillers, which reduce the skin’s sensitivity to heat.
- If you are taking photosensitising agents or medications, check the
package insert of your medicine and never use the appliance if it is stated that it can cause photo-allergic reactions, photo-toxic reactions or if you have to avoid sun when taking this medicine.
- If you take anticoagulation medications, including heavy use of aspirin, in
a manner which does not allow for a minimum 1-week washout period prior to each treatment.
- If you take immunosuppressive medications.
Never use the appliance on the following areas:
- In the face.
- On nipples, areolas, labia minora, vagina, anus and the inside of the
nostrils and ears.
- Men must not use it on the scrotum and face.
- Over or near anything articial like silicone implants, pacemakers,
subcutaneous injection ports (insulin dispenser) or piercings.
- On moles, freckles, large veins, darker pigmented areas, scars, skin
anomalies without consulting your doctor. This can result in a burn and a change in skin colour, which makes it potentially harder to identify skin-related diseases (e.g. skin cancer).
- On warts, tattoos or permanent make-up. This can result in a burn and
a change in skin colour.
®
or Roaccutane®
ENGLISH12
- On areas, where you use long-lasting deodorants. This can result in skin
reactions. See chapter ‘Using the appliance’, section ‘Possible side effects and skin reactions’.
Never use the appliance on sunburnt, recently tanned (last 48 hours) or fake-tanned skin:
- All types of tanning can inuence the safety of the treatment. This
applies to exposure to natural sunlight as well as articial tanning
methods, such as tanning lotions, tanning appliances etc. If you are tanned or are planning to tan, see chapter ‘Preparing for use’, section ‘Tanning advice’.
Note: This list is not exhaustive. If you are not sure whether you can use the appliance we advise you to consult a doctor.
Electromagnetic elds (EMF)
This Philips appliance complies with all standards regarding electromagnetic
elds (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientic evidence
available today.
Charging
Fully charge the batteries before you use the appliance for the rst time
and when the batteries are empty. Fully charging the batteries takes up to 1 hour and 40 minutes. Charge the appliance when the charging light lights up orange during use to indicate that the battery is low. When this happens, the remaining capacity
is at least 30 ashes. Fully charged batteries provide at least 320 ashes at light intensity 5.
Fully charge the appliance every 3 to 4 months, even if you do not use the appliance for a longer time.
Charge the appliance in the following way:
1 Switch off the appliance.
2 Insert the small plug into the appliance and put the adapter in the
wall socket.
, The charging light ashes green to indicate that the appliance is
charging.
, When the batteries are fully charged, the charging light
lights up green continuously.
Notes:
- The adapter and the appliance feel warm during charging. This is
normal.
- You cannot use the appliance during charging.
- This appliance is equipped with battery-overheat protection and does
not charge if the room temperature exceeds 40°C.
Never cover the appliance and adapter during charging.
3 After charging, remove the adapter from the wall socket and pull the
small plug out of the appliance.
ENGLISH 13
Preparing for use
For optimal results and greatest effect, prepare the areas on which you intend to use the appliance in the manner described below.
Preparing treatment areas
1 Shave the areas you intend to treat as long as you still experience
hair regrowth.
Note: If your last depilation method involved removing hairs by the roots (e.g
epilating, waxing etc.), wait until you notice signicant hair regrowth before you
use Philips Lumea. Do not use depilatory creams instead of shaving.
Please note that treatment on unshaved or improperly shaved areas has a number of undesired effects:
- The light exit window and attachment may become contaminated with
stray hairs and dirt. A contaminated light exit window and attachment
can reduce the life and efcacy of the appliance. In addition, burns or
black spots that appear on the light exit window and attachment due to contamination can cause the treatment to become painful or cause skin reactions like redness and discolouration.
- Hairs on your skin can burn, which can result in an unpleasant smell.
2 Clean your skin and make sure it is hair-free, entirely dry and
free from oily substances (e.g. present in cosmetic products like deodorants, lotions, perfumes, tanning creams and sunscreens).
3 Check the appliance, especially the light exit window and attachment,
for trapped hair, dust and bres. If you see any contamination, clean
the appliance according to the instructions in chapter ‘Cleaning and maintenance’.
Notes:
- If shaving causes wounds or lesions, your skin may be more sensitive
and the light treatment may sometimes feel uncomfortable.
- Once the hairs stop growing back, which usually happens after 4-5
treatments, you no longer have to shave before you use the appliance.
Setting the light intensity
Philips Lumea is an appliance developed for consumer use at home and therefore not comparable with professional light-based appliances with respect to pain sensation. The pulses of light delivered by Philips Lumea are gentler than those from professional appliances and therefore you can expect a convenient and effective treatment. You have to adjust the light intensity to your skin and body hair colour and
to a level you nd comfortable.
The recommended light intensities table below helps you to establish the right light intensity.
1 Consult the table below to determine which light intensities are most
suitable for your skin and body hair colour and to check if this method is suitable for you (if it is not, this is indicated with x in the table).
2 Each body area and possibly even parts of a body area may require a
separate appropriate light intensity according to the recommended light intensities table below. The method is more effective at higher intensities, but you should reduce the light intensity if you experience any pain or discomfort.
ENGLISH14
Persons with darker skin run a higher risk of skin irritation because their skin absorbs more light. Therefore lower intensities are recommended for persons with darker skin.
The light pulse can feel warm or hot on the skin but should never be painful. To prevent skin reactions, see chapter ‘Using the appliance’, section ‘Possible side effects and skin reactions’.
Recommended light intensities (1-5)
In the table below, ‘x’ means that the appliance is not suitable for you.
Skin colour and characteristics:
Body hair colour: dark blond/light
brown/brown/ dark brown/black
white/grey/red/ light blond
White (always sunburn, no tanning)
4/5 4/5 4/5 3/4 1/2/3 x
x x x x x x
Beige (easy sunburn, minimal tanning)
Important
To check whether Philips Lumea is suitable for you, see section ‘For whom is Philips Lumea not suitable?’.
If your skin has been exposed to natural sunlight or an articial tanning
method, it may be darker than during the previous treatment. Check the table above to determine which settings are suitable for your skin colour.
Tanning advice Sun exposure before treatment
- Wait at least 48 hours after sunbathing before you use the appliance.
Sunbathing can cause skin to darken (tan) and/or can cause sunburn (reddening of the skin).
- After these 48 hours, check the skin for any remaining sunburn. Do not
use Philips Lumea as long as sunburn persists.
- When the sunburn has disappeared, perform a skin test (see chapter
‘Using the appliance’, section ‘First use’) on the area to be treated to determine the appropriate light intensity.
- If your skin is tanned, perform a skin test (see chapter ‘Using the
appliance’, section ‘First use’) on the area to be treated to determine the appropriate light intensity. A failure to do so causes a risk of developing skin reactions after treatment with Philips Lumea.
Sun exposure after treatment
- Wait at least 24 hours after treatment before you expose treated
areas to the sun. Even after 24 hours, make sure that the treated skin does not show any redness from the treatment anymore before you expose it to the sun.
Light brown (sometimes sunburn, good tanning)
Mid brown (rarely sunburn, fast and good tanning)
Dark brown (rarely sunburn, very good tanning)
Brownish black and darker (rarely to never sunburn, very dark tanning)
ENGLISH 15
- Cover treated areas when you go out into the sun or use a sunblock
(SPF 30+) in the two weeks after treatment.
- Exposing treated areas to sunlight without protection immediately
after treatment can increase the risk of adverse side effects and skin reactions. See chapter ‘Using the appliance’, section ‘Possible side effects and skin reactions’.
Tanning with articial light
- Follow the instructions in ‘Sun exposure before treatment’ and ‘Sun
exposure after treatment’ above.
Tanning with creams
- If you have used an articial tanning lotion, wait until the articial tan
has fully disappeared before you use Philips Lumea.
Note: For more details on unwanted skin reactions, see chapter ‘Using the appliance’, section ‘Possible side effects and skin reactions’.
Using the appliance
Check the recommended light intensities table in chapter ‘Preparing for use’, section ‘Setting the light intensity’ to determine which light intensities are most suitable for your skin and body hair colour. Use the appliance in a well-lit room; this reduces the perceived brightness of the ash. Shave the area you intend to treat before you use the appliance (see chapter ‘Preparing for use’, section ‘Preparing treatment areas’).
If the treatment becomes intolerably painful at any point in time, reduce the light intensity setting until the treatment is comfortable again. If you notice skin reactions stronger than slight redness, stop the treatment immediately and read section ‘Possible side effects and skin reactions’ in this chapter.
First use and skin test
1 Attach the body attachment to the appliance.
The body attachment can be used to treat unwanted body hair on all body areas below the neck (for exceptions, see chapter ‘Important’, section ‘Contraindications’).
2 Choose an area close to the area you intend to treat.
ENGLISH16
3 Press the on/off button to switch on the appliance.
, The appliance always starts automatically at the lowest setting.
4 Apply one ash at the lowest recommended intensity for your skin
type (for instructions on how to release a ash, see steps 6 to 9
of section ‘Subsequent use’ in this chapter).
5 As long as it feels comfortable (not painful), increase the setting by
one level within the recommended range for your skin type and
apply one ash for each setting. Do not apply more than one ash on
the same spot.
6 After the skin test, wait for 24 hours and check your skin for
any reaction. If your skin shows reactions, choose the highest setting that did not result in any skin reaction for subsequent use.
When you use the appliance for the rst time, we advise you to perform
a skin test on the area to be treated to check your skin’s reaction to the treatment and to get accustomed to light-based treatment.
Subsequent use
1 Before every treatment, clean the attachment, the light exit window
and the metallic frame inside the attachment of Philips Lumea. For more information see chapter ‘Cleaning and maintenance’.
2 Press the on/off button to switch on the appliance.
Note: It is normal that the appliance and the attachment become warm during use.
3 Start each treatment by selecting the light intensity very carefully,
based on your skin’s sensitivity and on how comfortable treatment feels.
Your skin may react differently on different days/occasions for a number of reasons. See section ‘Possible side effects and skin reactions’ in this chapter for more information.
ENGLISH 17
4 Press the % button to increase the intensity. To lower the intensity,
press the ^button.
, Every time you press the button, the corresponding intensity
light starts to ash. This takes a few seconds.
5 Place the appliance in a 90° angle on the skin so that the attachment
and the safety ring are in contact with the skin.
6 Press the safety ring fully onto the skin with slight pressure.
Note: The safety ring has contact switches that together are the safety system
of the appliance. This safety ring prevents unintentional ashing without skin
contact.
, The ‘ready to ash’ light on the back of the appliance lights up green
when all contact switches of the safety ring are in contact with the skin and the appliance is charged. This may take up to 3.5 seconds.
Tip: For easier use, stretch the area of skin you want to treat. On areas with softer skin, you may need to exert more pressure on the appliance to push in all contact switches.
7 Press the ash button to release a ash.
Note: The visible light produced by the appliance is the reection of the ash
on the skin and is harmless to your eyes. It is not necessary to wear goggles during use.
8 Let go of the ash button after the appliance has ashed. 9 For the next ash, repeat steps 6 to 9. After each ash it takes up to
3.5 seconds until the appliance is ready to ash again.
Do not treat exactly the same area multiple times during one session. This does not improve the effectiveness of the treatment, but increases the risk of skin reactions.
ENGLISH18
10 To avoid untreated areas, always make sure there is some overlap
with the previously treated area when you place the appliance on the skin.The effective light only comes out of the light exit window. Make
sure the ashes are produced close to each other.
11 Switch off the appliance after you have nished the treatment. 12 Check the light exit window and the attachment for hairs and
dirt and clean the appliance after use (see chapter ‘Cleaning and maintenance’).
Guidelines for treatment
Average treatment time
Area Approx. treatment time
Underarms 1.5 minutes per underarm Bikini line 1.5 minutes per side Entire bikini area 5 minutes One lower leg 12 minutes One full leg 20 minutes
Note: The average treatment times above have been observed during research and tests. Individual treatment times may vary from person to person.
Note: Fully charged batteries offer at least 320 ashes at intensity 5. How long
you can use the appliance depends on the size of the area to be treated and the intensity setting used.
Using the appliance on the legs
Check the recommended light intensities table in chapter ‘Preparing for use’, section ‘Setting the light intensity’ to see which settings are suitable for your legs.
- You can move the appliance up and down or across the leg, whichever
is more convenient to you.
Note: Bony areas like shinbone and ankles are more sensitive than other areas of the body. When you press the attachment hard onto these areas, the skin can be more susceptible to skin reactions, such as skin irritation and redness. See section ‘Possible side effects and skin reactions’ in this chapter. Press the
attachment onto the skin just hard enough to make the ‘ready to ash’ light go
on, but not harder. Tip: The appliance may leave imprints on the skin in the treated areas. These
imprints may show you where you can make the treated areas overlap.
If you use the appliance to treat both your lower and upper legs, you may have to recharge the appliance during the treatment. This is normal. How long you can use the appliance depends on the size of the treatment area and the intensity setting used.
Tip: Many users combine leg treatments with other activities around the house such as watching TV or listening to music. You can also try this to make the experience more enjoyable and relaxing.
ENGLISH 19
Using the appliance in the bikini area
Check the recommended light intensities table in chapter ‘Preparing for use’, section ‘Setting the light intensity’ to see which settings are suitable for your bikini area. In principle, Philips Lumea is safe and gentle enough for treatment of the entire bikini area (e.g. for ‘Brazilian’ or ‘Hollywood’ style). Use a lower setting on darker pigmented, more sensitive skin in the bikini area. Do not use the
appliance on inner labia, vagina and anus. Men who wish to treat their pubic
area must not use the appliance on the scrotum.
Note: For hygienic reasons, always clean the attachment before you start treating another body area.
Using the appliance on the underarms
Check the recommended light intensities table in chapter ‘Preparing for use’, section ‘Setting the light intensity’ to see which settings are suitable for your underarms.
Make sure you remove any deodorant, perfume, cream or other skin care
product from your underarms before treatment.
Tip: To achieve optimal results on your underarms, stand in front of a mirror to
get a good view of the area to be treated and the ‘ready to ash’ light. Raise
your arm and place your hand in your neck to stretch the skin in the underarm area. In this way the safety ring can be pressed more easily onto the skin, which makes the treatment easier to perform.
Note: The reected light does not harm your eyes. If the scattered light is unpleasant, close your eyes when you release a ash.
How to achieve optimal results
- It is normal that hairs are still visible after the rst few treatments (see
chapter ‘Introduction’, section ‘Working principle’ for more information).
- To remove all hairs successfully and prevent the hair follicle from
becoming active again, the treatments have to be repeated once every
two weeks for the rst two months. Your skin should be smooth and hair-free by then. Please read section ‘Maintenance phase’ to nd out
how you can keep these results.
Maintenance phase
- To ensure that your skin stays smooth and hair-free, we advise you
to repeat the treatment every four to six weeks. The time between treatments may vary based on your individual hair regrowth and also across different body areas. If too many hairs grow back between treatments, simply shorten the treatment interval again, but do not treat any area more often than once every two weeks. When you use the appliance more frequently than recommended, you do not increase the effectiveness but you do increase the risk of skin reactions.
Possible side effects and skin reactions Common skin reactions:
- Your skin may show slight redness and/or may prickle, tingle or feel
warm. This reaction is absolutely harmless and disappears quickly.
- A skin reaction similar to sunburn may occur on the treated area for a
short while. If this does not disappear within 3 days, we advise you to consult a doctor.
ENGLISH20
- Dry skin and itching may occur because of the combination of shaving
and light treatment. This is harmless and disappears within a few days. You can cool the area with an ice pack or a wet cloth. If dryness persists, you can apply a non-scented moisturiser on the treated area 24 hours after the treatment.
Rare side effects:
- Burns, excessive redness and swelling: these reactions occur very rarely.
They are the result of using a light intensity that is too high for your skin colour. If these reactions do not disappear within 3 days, we advise you to consult a doctor. Wait with the next treatment until the skin has healed completely and make sure you use a lower light intensity.
- Skin discolouration: this occurs very rarely. Skin discolouration manifests
itself as either a darker or lighter patch than the surrounding area. This is the result of using a light intensity that is too high for your skin colour. If the discolouration does not disappear within 2 weeks, we advise you to consult a doctor. Do not treat discoloured areas until the discolouration has disappeared and your skin has regained its normal skin colour.
- Skin infection and inammation: This occurs very rarely and may be
caused by using the appliance on wounds or cuts that resulted from shaving, on already existing wounds or on ingrown hairs.
- Excessive pain: this can occur during or after treatment if you have
used the appliance on unshaved skin, if you use the appliance at a light
intensity that is too high for your skin colour, if you ash the same
area more than once and if you use the appliance on open wounds,
inammations, infections, tattoos, burns, etc. See chapter ‘Important’,
section ‘Contraindications’ for more information.
After use
- Do not apply any perfumed cosmetics to the areas treated immediately
after treatment.
- Do not use deodorant immediately after treating the underarms. Wait
until any skin redness has disappeared completely.
- See chapter ‘Preparing for use’, section ‘Tanning advice’ for information
about sun exposure and articial tanning.
Cleaning and maintenance
To ensure optimal results and a long life for the appliance, clean the appliance before and after each use and, if necessary, also during the treatment. The appliance loses its effectiveness if you do not clean it properly.
Never clean the appliance or any of its parts under the tap or in the dishwasher.
Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance.
Never scratch the light exit window or the metallic frame inside the attachment.
Note: Make sure that the contact switches of the safety ring do not get congested with dirt.
ENGLISH 21
Note: Stop using the appliance when it is no longer possible to clean the light exit window or the attachment.
1 Switch off the appliance, unplug it and let it cool down.
Note: The light exit window becomes hot during use. Make sure it has cooled down before you clean it.
2 To remove the attachment, put your ngers in the recesses at the
top and bottom and pull gently. The attachment should come off easily.
3 Moisten the soft cloth supplied with the appliance with a few drops
of water and use it to clean the following parts:
- the light exit window
- the outside surface of the attachment
- the metallic frame inside the attachment
Note: If water does not clean effectively, use a few drops of high-percentage alcohol to clean the parts mentioned above.
Note: A contaminated light exit window and/or attachment can look like this picture. Make sure you clean the appliance before and after each use and, if necessary, also during the treatment according to the instructions in this section.
Tip: If it is no longer possible to clean the edges of the attachment with the
enclosed cleaning cloth, use a cotton bud instead. Make sure that no uff or bres stay behind on the attachment or on the light exit window.
4 If necessary, clean the outside of the appliance with the dry soft
cleaning cloth supplied with the appliance.
Storage
1 Switch off the appliance, unplug it and let it cool down. 2 Clean the appliance before you store it. 3 Put the appliance in the pouch supplied. 4 Store the appliance in a dry place at a temperature between 0°C
and 60°C.
Replacement
If you have to replace a part or want to purchase an additional part, go to your Philips dealer or visit www.philips.com/support. If you have problems obtaining the parts, please contact the Philips Consumer Care Centre in your country.
Replacement parts
The following replacement parts are available:
- Body attachment
- Adapter
- Pouch
ENGLISH22
Environment
- Do not throw away the appliance with the normal household waste
at the end of its life, but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve the environment.
- The built-in rechargeable batteries contain substances that may pollute
the environment. Always remove the batteries before you discard and
hand in the appliance at an ofcial collection point. Dispose of the batteries at an ofcial collection point for batteries. If you have trouble
removing the batteries, you can also take the appliance to a Philips service centre. The staff of this centre will remove the batteries for you and will dispose of them in an environmentally safe way.
Removing the rechargeable batteries
Only remove the rechargeable batteries if they are completely empty.
1 Insert an awl or another pointed tool into the bottom cap of the
appliance and pry off the bottom cap.
2 Undo the two screws in the bottom of the handle with a
screwdriver.
3 Remove the bottom part of the handle and cut the two wires that
connect the bottom part to the appliance.
ENGLISH 23
4 Pull the battery connectors off the battery terminals with long
nose pliers.
5 Pull the rechargeable batteries out of the appliance with long
nose pliers.
6 Cut the two wires one at a time to ensure that no mishaps due to
possible residual charge occur.
Guarantee and service
If you need service or information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Consumer Care Centre in your country (please look for the phone number in the
worldwide guarantee leaet). If there is no Consumer Care Centre in your
country, go to your local Philips dealer.
Technical specications
Model SC2001/01
Rated voltage 100V-240V Rated frequency 50Hz-60Hz Rated input 7.5W Protection against electric shock Class II Q Protection rating IP 30 (EN 60529) Operating conditions Temperature: +15° to +35°C
Relative humidity: 25% to 95%
ENGLISH24
Model SC2001/01
Storage conditions Temperature: 0° to +60°C
Relative humidity: 5% to 95% Spectrum of body attachment >570nm Lithium-ion battery 2 x 3.7 Volt 1500 mAh
Troubleshooting
This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, contact the Consumer Care Centre in your country
(please look for the phone number in the worldwide guarantee leaet).
Problem Possible cause Solution
The appliance does not work.
The appliance suddenly switches off.
The adapter becomes warm during charging.
The charging light does not go on when I put the small plug in the appliance socket.
The rechargeable batteries are empty.
The appliance is defective.
The rechargeable batteries are empty.
This is normal. No action required.
You have not put the adapter in the wall socket.
The wall socket is not live.
The adapter is not inserted properly into the wall socket and/or the small plug is not inserted properly into the appliance socket.
The appliance is defective.
Charge the appliance (see chapter ‘Charging’).
Contact the Consumer Care Centre in your country, your Philips dealer or a Philips service centre.
Charge the appliance (see chapter ‘Charging’).
Insert the small plug into the appliance socket and put the adapter in the wall socket.
Connect another appliance to the wall socket to check if the wall socket is live. If the socket is live but the appliance still does not charge, contact the Consumer Care Centre in your country, your Philips dealer or a Philips service centre.
Make sure the adapter is inserted properly into the
wall socket and/or the small plug is inserted properly into the appliance socket.
Contact the Consumer Care Centre in your country, your Philips dealer or a Philips service centre.
Problem Possible cause Solution
ENGLISH 25
I have switched on the appliance but I cannot increase or decrease the light intensity.
The ‘ready to ash’ light
does not go on when I place the appliance on the skin.
The ‘ready to ash’ light
does not go on when I place the attachment on my skin, but the cooling fan works.
The ‘ready to ash’ light is
green but the appliance
does not produce a ash when I press the ash
button.
The appliance becomes warm during use.
The appliance does not show light intensity 1 when I switch it on.
The appliance produces a strange smell.
The appliance has to be reset.
You have not put the attachment with safety ring properly on the skin.
The safety ring is dirty.
The overheat protection has been activated.
The appliance needs to be reset.
This is normal. No action required.
The appliance needs to be reset.
The attachment
and/or the lter
glass is dirty.
To reset the appliance, switch off the appliance and then switch it on again. If you still cannot adjust the light intensity, contact the Consumer Care Centre in your country, your Philips dealer or a Philips service centre.
Place the appliance in a 90° angle onto the skin in such a way that all contact switches touch the skin. Then
check if the ‘ready to ash’ light is on and press the ash button.
If this does not work, place the appliance on a part of your body where it is easy to establish full skin contact, for example on your lower arm.Then check
if the ‘ready to ash’ light works. If the ‘ready to ash’
light still does not go on when you place the appliance on the skin, contact the Consumer Care Centre in your country, your Philips dealer or a Philips service centre.
Clean the safety ring carefully. If you are unable to clean the safety ring properly, contact the Consumer Care Centre in your country, your Philips dealer or a Philips service centre to replace the attachment.
When the overheat protection has been activated, the fan still works. Do not switch off the appliance and let it cool down for approx. 15 minutes before
you continue to use it. If the ‘ready to ash’ light still
does not go on when you place the appliance on the skin, contact the Consumer Care Centre in your country, your Philips dealer or a Philips service centre.
To reset the appliance, switch off the appliance and
switch it on again. If the ‘ready to ash’ light is green but the appliance still does not produce a ash when you press the ash button, contact the Consumer Care
Centre in your country, your Philips dealer or a Philips service centre.
To reset the appliance, switch it off and on again. If the appliance still does not show light intensity 1, contact your Customer Care Centre, your Philips dealer or a Philips Service Centre.
Clean the attachment carefully. If you are unable to clean the attachment properly, contact the Consumer Care Centre in your country, your Philips dealer or a Philips service centre to replace the attachment.
ENGLISH26
Problem Possible cause Solution
The skin feels more sensitive than usual during treatment.
I experience an unacceptable pain sensation when I use the appliance.
The treated areas become red after the treatment.
You have not shaved the area to be treated properly.
You stored the appliance in a dusty environment.
The light intensity you use is too high.
You did not shave the areas to be treated.
The UV lter
of the light exit window is broken.
The appliance is defective.
You did not shave the areas to be treated
You treated an area for which the appliance is not intended.
You have used a light intensity which is too high for you.
The light exit window is broken.
The appliance is not suitable for your skin colour.
Slight redness is harmless and normal and disappears quickly.
If there are hairs on the area to be treated, these hairs may get burnt when you use the appliance. As a result, you notice a strange smell. Shave the area to be treated properly before you use the appliance. If shaving causes skin irritation, trim hairs as short as possible and use a comfortable setting.
The strange smell disappears after a few ashes.
Check if you have selected the right light intensity. If necessary, select a lower light intensity.
Shave the areas to be treated before you use the appliance. If shaving causes skin irritation, trim hairs as short as possible and use a comfortable setting.
If the UV lter of the light exit window is broken, do
not use the appliance anymore. Contact the Consumer Care Centre in your country, your Philips dealer or a Philips service centre.
Contact the Consumer Care Centre in your country, your Philips dealer or a Philips service centre.
Shave the areas to be treated before you use the appliance. If shaving causes skin irritation, trim hairs as short as possible and use a comfortable setting.
You must not use the appliance on your inner labia, vagina, anus, nipples, areolas, lips, inside the nostrils and
ears, in the region of your eyes and eyebrows. Men
must not use it on their face or scrotum. Reduce the light intensity to a level that is comfortable
for you. See chapter ‘Preparing for use’, section ‘Setting the light intensity’.
If the light exit window is broken, do not use the appliance with this attachment any more. Go to your dealer or a Philips service centre or contact the Consumer Care Centre to have the attachment replaced.
Do not use the appliance if you have a very dark skin. Do not use it either if your body hair is light blond, red, grey or white.
No action required.
Problem Possible cause Solution
ENGLISH 27
The skin reaction after the treatment lasts longer than usual.
The hair-removal results are not satisfactory.
Hair starts to grow again in some spots on the treated areas.
You have used a light intensity which is too high for you.
You have used a light intensity which is too low for you.
You did not make enough overlaps when you used the appliance.
You do not use the appliance as often as recommended.
The appliance is not suitable for your hair or skin colour.
You did not make enough overlaps when you used the appliance.
Hair starts to grow again as part of the natural cycle of hair growth.
Select a lower light intensity the next time. See chapter ‘Preparing for use’, section ‘Setting the light intensity.
If the skin reaction lasts longer than 3 days, contact your doctor.
Select a higher light intensity the next time.
For proper hair-removal results, you have to make overlaps when you use the appliance. See chapter ‘Using the appliance’, step 11.
To remove all hairs successfully and to prevent the hair root from becoming active again, the treatments have
to be repeated once every two weeks for the rst two
months. Your skin should be smooth and hair-free by then. To ensure that you keep these results, we advise you to repeat the treatments on the underarms, bikini area, arms and stomach every two weeks. On the legs, regrowth is usually slower. Therefore, a treatment
once every four weeks is probably sufcient to keep
your legs smooth and hair-free. If you see too many hairs grow back within these four weeks, then simply shorten the interval between treatments again, but do not treat more often than once every two weeks.
Do not use the appliance if your body hair is light blond, red, grey or white. Do not use the appliance either if you have very dark skin.
For proper hair-removal results, you have to make overlaps when you use the appliance. See chapter ‘Using the appliance’, step 11.
This is normal. It is part of the natural cycle of hair growth that hair starts growing again. The hairs that come back, however, tend to be softer and thinner.
28

DEUTSCH

Inhaltsangabe
Einführung 29
Vorteile 29
IPL-Technologie (“Intense Pulsed Light”) für die Verwendung
zu Hause 29 Das Nachwachsen von Haaren wird wirksam verhindert 29
Sanfte Behandlung, selbst an empndlichen Körperpar tien 30
Akkubetrieb für maximale Bewegungsfreiheit und Flexibilität 30 Die Lampe muss nicht ausgetauscht werden. 30
Die Technologie “Intense Pulsed Light” von Philips 30
Haarwuchs 30
Funktionsprinzip 30 Allgemeine Beschreibung 31 Wichtig 31
Gefahr 31 Warnhinweis 31
So vermeiden Sie Beschädigungen: 32
Achtung 32
Beachten Sie folgende Punkte, um die Lebensdauer von Philips Lumea
nicht zu beeinträchtigen: 32
Für wen ist Philips Lumea nicht geeignet? 32
Wichtige Hinweise 33
Verwenden Sie das Gerät nicht, wenn Sie schwanger sind oder stillen. 33
Verwenden Sie das Gerät nicht, wenn Ihre Haut- bzw. Haarfarbe für
eine Behandlung ungeeignet ist, d. h.: 33
Verwenden Sie das Gerät nicht, wenn Sie an einer der unten
aufgeführten Krankheiten leiden, d. h.: 33
Verwenden Sie das Gerät nicht, wenn Sie eines oder mehrere der
unten aufgeführten Medikamente einnehmen, d. h.: 33
Verwenden Sie das Gerät nicht an den folgenden Partien: 34
Verwenden Sie das Gerät nicht auf sonnenverbrannter, kürzlich
gebräunter (in den letzten 48 Stunden) oder künstlich gebräunter
Haut: 34
Elektromagnetische Felder 34 Laden 35 Für den Gebrauch vorbereiten 35
Die zu behandelnden Hautpartien vorbereiten 35
Die Lichtintensität einstellen 36
Empfohlene Lichtstärken (1 bis 5) 37 Wichtig 37 Hinweise zum Bräunen 37
Das Gerät benutzen 38
Erster Gebrauch und Hauttest 38
Weitere Verwendung 39
Hinweise zur Behandlung 41
Durchschnittliche Behandlungszeit 41 Das Gerät am Bein verwenden 41 Das Gerät für die Bikinizone verwenden 42
Das Gerät für die Achselhöhlen verwenden 42
Erzielen optimaler Ergebnisse 42 Behandlungsrhythmus 42
Mögliche Nebenwirkungen und Hautreaktionen 43
DEUTSCH 29
Nach dem Gebrauch 43
Reinigung und Pege 44
Aufbewahrung 45 Ersatz 45
Ersatzteile 45
Umwelt 45
Die Akkus entfernen 46 Garantie und Kundendienst 47 Technische Daten 47 Fehlerbehebung 48
Einführung
Herzlichen Glückwunsch zu Ihrem Kauf und willkommen bei Philips! Um
die Unterstützung von Philips optimal nutzen zu können, registrieren Sie Ihr
Produkt bitte unter www.philips.com/lumea.
Haarentfernung mit Licht ist eine der wirksamsten Methoden für eine lang anhaltende Entfernung von unerwünschtem Körperhaar. Sie unterscheidet
sich von gängigen Enthaarungsmethoden zur häuslichen Anwendung, indem
sie das Nachwachsen der Haare deutlich reduziert. Dieses Verfahren ist
das Ergebnis von mehr als zehnjähriger gemeinsamer Forschungs- und
Entwicklungsarbeit von Philips und führenden Dermatologen. Jetzt können Sie diese innovative Technologie jederzeit und ungestört zu Hause nutzen.
Dieses Gerät wurde speziell für Frauen entwickelt und optimiert, kann
jedoch ebenso von Männern verwendet werden. Es ist für die Entfernung von Körperhaar in folgenden Bereichen
vorgesehen:
- Achselhöhlen
- Arme
- Bauch
- Bikinizone
- Beine
Verwenden Sie Philips Lumea nicht im Gesicht.
Philips Lumea sollte nur von einer Person benutzt werden. Weitere Informationen zu Philips Lumea erhalten Sie unter www.
philips.com/lumea. Auf unserer Website nden Sie regelmäßig aktuelle
Informationen.
Vorteile
Dieses Gerät bietet die folgenden Vorteile:
IPL-Technologie (“Intense Pulsed Light”) für die Verwendung zu Hause
Philips Lumea arbeitet mit einer lichtbasierten Technologie namens “Intense Pulsed Light” (IPL), die bereits seit 15 Jahren in der Kosmetikbranche zur
Haarentfernung eingesetzt wird. Dank Philips Lumea können Sie diese
innovative Technologie nun auch zu Hause nutzen.
Das Nachwachsen von Haaren wird wirksam verhindert
Diese Methode sorgt langfristig dafür, dass weniger Haare nachwachsen
und Ihre Haut seidig glatt bleibt. Unsere Studien haben schon nach zwei Anwendungen ein deutlich geringeres Haarwachstum gezeigt. Optimale Ergebnisse wurden im Allgemeinen nach vier bis fünf Behandlungen erzielt.
Von Behandlung zu Behandlung ist eine Verringerung der Haardichte
DEUTSCH30
1
erkennbar. Wie schnell eine Wirkung sichtbar wird und wie lange die Ergebnisse anhalten, ist jedoch bei jeder Person unterschiedlich. Weitere Informationen erhalten Sie im Kapitel “Das Gerät benutzen” unter dem Abschnitt “Erzielen optimaler Ergebnisse”.
Sanfte Behandlung, selbst an empndlichen Körperpartien
Philips Lumea wurde in enger Zusammenarbeit mit führenden Dermatologen entwickelt. Das Resultat ist eine wirksame und sanfte
Behandlung, die selbst für die empndlichsten Körperpar tien geeignet ist.
Akkubetrieb für maximale Bewegungsfreiheit und Flexibilität
Da das Gerät mit Akkus betrieben wird, ist es tragbar und kann überall eingesetzt werden.
Die Lampe muss nicht ausgetauscht werden.
Philips Lumea ist mit einer Hochleistungslampe ausgestattet, die nicht ausgetauscht werden muss. Diese Lampe kann über 80.000 Lichtimpulse erzeugen. Damit sollten Sie mehr als 5 Jahre* lang gute Ergebnisse erzielen und gleichzeitig Geld für teure Ersatzlampen sparen. *Bei normalem Gebrauch und empfohlener Behandlung für einen Benutzer.
Die Technologie “Intense Pulsed Light” von Philips
Haarwuchs
Die Wuchsgeschwindigkeit von Haaren ist von Person zu Person unterschiedlich und von Alter, Stoffwechsel und anderen Faktoren abhängig. Im Allgemeinen erfolgt der Haarwuchs allerdings in 3 Phasen. 1 Wachstumsphase (Anagen-Phase) Dies ist die aktive Wachstumsphase, in der das Haar über die Wurzel
genährt wird. In dieser Phase enthält es die höchste Konzentration an Melanin – ein Pigment, das für die Färbung von Haaren verantwortlich ist. Die Melaninkonzentration ist darüber hinaus der entscheidende Faktor für die Wirksamkeit dieser Methode. Nur die Haare in der Wachstumsphase können durch Lichtbehandlung entfernt werden.
2 Abbauphase (Catagen-Phase) Das Haar wächst nicht mehr, und die Wurzel schrumpft, bevor das Haar ausfällt. 3 Ruhephase (Telogen-Phase)
Das alte Haar löst sich vom Haarfollikel und fällt aus. Der Follikel ruht, bis
ihm die biologische Uhr mitteilt, dass er wieder aktiv werden und ein neues Haar wachsen lassen soll.
Funktionsprinzip
Zum Entfernen von Haaren erhitzt das Gerät das Haar und die Wurzel
unter der Haut. Das Melanin im Haar und in der Haarwurzel absorbiert
die vom Gerät produzierten Lichtimpulse. Je dunkler das Haar, desto mehr
Licht kann aufgenommen werden. Dieser Vorgang regt das Haar an, in die
Ruhephase überzugehen. Das Haar fällt nun auf natürliche Weise aus, und der Haarwuchs wird unterdrückt. Es kann bis zu zwei Wochen dauern, bis die Haare ausfallen. Eine optimale Haarentfernung kann nicht durch eine einzige Behandlung erzielt werden, da nur Haare in der Wachstumsphase auf die Lichtbehandlung reagieren und sich die Haare im behandelten
Körperbereich normalerweise in verschiedenen Wachstumsphasen benden. Zur effektiven Behandlung aller Haare sollten Sie die Behandlung
Loading...
+ 144 hidden pages