Standard product information
• Power supply 9V DC via 220-240 VAC/
50 Hz adapter
• Power consumption 7 Watts
• Operating temperature 5 to 45 ˚C
• Storage temperature -25 to 55 ˚C
• Plug and Play system via SCART output connectors
• Dual source input two video source inputs
• Supported video
standards PAL/NTSC/SECAM
System information
Audio/video transmission
• Carrier frequency 2.4 GHz
• Transmission power <10 mW
• Type of modulation FM
• Multiple RF channels 4* to allow interference-free
operation
• Antenna built-in
• Typical range up to 100 m in open air,
up to 30 m indoors
* May vary per country according to local regulations
System information
Remote control extender
• Carrier frequency 433.92 MHz
• Transmission power <10 mW
• Type of modulation AM
• Antenna mounted on the rear,
can be rotated
Transmitter unit
• Dimensions (LxWxH) 204 x 168 x 65 mm
• Power on/off switch on the front
• Input selection switch on the front
• Input 1 SCART (CVBS)
• Input 2 SCART (CVBS)
• Output 1 SCART (CVBS)
• Output 2 SCART (CVBS)
• Remote control
extender cord yes, with 2 eyes
• Built-in IR transmitter yes
Receiver unit
• Dimensions (LxWxH) 204 x 168 x 65 mm
• Power on/off switch on the front
• Output SCART (CVBS)
• Built-in IR receiver yes
• Range of IR receiver up to 7 metres max.
Packaging contents
• 1 transmitter unit
• 1 receiver unit
• 2 SCART cables
• 2 power supply adapters
• 1 remote control extender cord
• 1 Instructions for use booklet
Wireless TV Link
Watch and control video source devices anywhere in your home
The Philips Wireless TV Link lets you watch, control and enjoy video sources on
a second TV anywhere in your house. There’s no need to buy or rent duplicate
A/V equipment! It is the ideal solution for delivering crystal clear pictures and
high-quality stereo sound to the second TV.
Dual source input, gives you the choice of any two devices
The Wireless TV Link has two separate inputs to allow you to choose
between any two video source devices. A button on the transmitter unit
simply selects the input.
Built-in Universal remote control extender
The Universal remote control extender also enables you to operate the video
source equipment using the original (or a universal) remote control unit.
A remote control extender cord (supplied) ensures perfect contact with the
IR remote control sensors on your video source devices.There’s no need to
run downstairs to press buttons.
Plug and Play system, install in seconds
Installation takes just a matter of seconds.The antennas are integrated into
the stylish units, and connections to source equipment and TVs are made using
familiar SCART cables (two are supplied).And there is no complicated set-up
procedure, so it really is Plug and Play.
No cable laying, hole drilling or antenna siting
Because it uses a wireless RF link, you don’t have to run long video cables
through walls or under floorboards – and no need for signal booster
amplifiers either.The antennas are built-in to the units so you don’t have
to worry about positioning them.
Signal passes through walls and ceilings
The RF signal passes right through walls and ceilings within your home.
With a range of up to 30 m inside the house, it delivers interference-free
video and stereo audio no matter where your second TV is located.
A multiple-position slide-switch allows different transmission frequencies
to be selected to avoid interference from other RF devices.
Suitable for all the latest home A/V equipment
The Wireless TV Link is suitable for all brands of Pay TV and Pay-per-View
decoders, satellite receivers, set-top boxes, DVD players,VCRs and
Camcorders. It extends your possibilities for viewing movies, sports events,
live performances and an incredibly wide range of TV channels anywhere
in your home.
Helpdesk available
Should you have any questions, comments or recommendations about
the Wireless TV Link, please call our help-line.
Philips Accessories
Data subject to change without notice
©2000 Royal Philips Electronics
All rights reserved
http://www.philips.com
SBC VL1200
SBC VL1200
Helpdesk available